Loading…
Loading…
Tender Value
₹9.2 Cr
EMD Value
₹18.4 L
Closing Date
1 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
S AND T
20 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less, where V= Advertised value of the tender in crores of Rupees, N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure -VI B, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Format of Annexure VI B is attached with document tab for reference.
Date of inviting tender shall be the date of publishing tender notice on IREPS website if tender is published on website or the date of publication in newspaper in case tender is not published on website.
The balance sheet and all other financial documents attested/certified by CAs to substantiate fulfilment of Financial Eligibility Criteria should be with UDIN (Unique Document Identification Number), failing which the offer is likely to be rejected without any further reference.
(a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s)during last 07 years ending last day of month previous to the one in which tender is invited:Three similar works each costing not less than the amount equal to 30% of advertised value of the tender or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender,or One similar work costing not less than the amount equal to 60% of advertised value of the tender.b(1)In case of tenders for composite works(e.g.works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges-substructure, superstructure etc),tenderer must have successfully completed or substantially completed any one of the following categories of work(s)during last07(seven)years, ending last day of month previous to the one in which tender is invited:(i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or(ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or(iii)One similar work each costing not less than the amount equal to60% of advertised value of each component of tender. Note for b(1):Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components.(b) (2) In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity.(b)(3)To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause7of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause7of the Standard General Conditions of Contract or jointly i.e, partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s),and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50lakh,no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s)fulfilling the requirements as per clause7of the IRSGCC,with prior approval of Chief Engineer in writing.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Explanation for Eligibility Criteria- 1. Substantially Completed Work means an ongoing work in which payment equal to or more than 90% of the present contract value (excluding the payment made for adjustment of Price variation (PVC), if any) has been made to the contractor in that ongoing contract and no proceedings of termination of contract on Contractor's default has been initiated. The credential certificate in this regard should have been issued not prior to 60 days of date of invitation of present tender. 2. In case a work is started prior to 07 (seven) years, ending last day of month previous to the one in which tender is invited, but completed in last 07 (seven) years, ending last day of month previous to the one in which tender is invited, the completed work shall be considered for fulfillment of credentials. 3. If a work is physically completed and completion certificate to this extent is issued by the concerned organization but final bill is pending, such work shall be considered for fulfillment of credentials 4. In case of completed work, the value of final bill (gross amount) including the PVC amount (if paid) shall be considered as the completion cost of work. In case final bill is pending, only the total gross amount already paid including the PVC amount (if paid) shall be considered as the completion cost of work. In case of substantially completed work, the total gross amount already paid including the PVC amount (if paid), as mentioned in the certificate, shall be considered as the cost of substantially completed work. 5. If a 1.1.1 bidder has successfully completed a work as subcontractor and the work experience certificate has been issued for such work to the subcontractor by a Govt. Organization or public listed company as defined in Note for Item 10.1 Para 10 of the Tender Form (Second Sheet) of GCC JULY 2022, the same shall be considered for the purpose of fulfillment of credentials. 6. In case a work is considered similar in nature for fulfillment of technical credentials, the overall cost including the PVC amount (if paid) of that completed work or substantially completed work, shall be considered and no separate evaluation for each component of that work shall be made to decide eligibility. 7. In case of newly formed partnership firm, the credentials of individual partners from previous propriety firm(s) or dissolved previous partnership firm(s) or split previous partnership firm(s), shall be considered only to the extent of their share in previous entity on the date of dissolution / split and their share in newly formed partnership firm. For example, a partner A had 30% share in previous entity and his share in present partnership firm is 20%. In the present tender under consideration, the credentials of partner A will be considered to the extent of 0.3*0.2*value of the work done in the previous entity. For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deed(s), dissolution deed(s) and proof of surrender of PAN No.(s) in case of dissolution of partnership firm(s) etc.
8. In case of existing partnership firm, if any one or more partners quit the partnership firm, the credentials of remaining partnership firm shall be re-worked out i.e., the quitting partner(s) shall take away his credentials to the extent of his share on the date of quitting the partnership firm(e.g. in a partnership firm of partners A, B & C having share 30%, 30% & 40% respectively and credentials of Rs 10 crore; in case partner C quits the firm, the credentials of this partnership firm shall remain as Rs 6 crore). For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deed(s), dissolution deed(s) and proof of surrender of PAN No.(s) in case of dissolution of partnership firm(s) etc.9. In case of existing partnership firm if any new partner(s) joins the firm without any modification in the name and PAN/TAN no. of the firm, the credentials of partnership firm shall get enhanced to the extent of credentials of newly added partner(s) on the same principles as mentioned in item 6 above. For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deeds, dissolution/splitting deeds and proof of surrender of PAN No.(s) in case of dissolution of partnership firm etc. 10. Any partner in a partnership firm cannot use or claim his credentials in any other firm without leaving the 1.1.2 partnership firm i.e., In a partnership firm of A&B partners, A or B partner cannot use credentials of partnership firm of A&B partners in any other partnership firm or propriety firm without leaving partnership firm of A&B partners. 11. In case a partner in a partnership firm is replaced due to succession as per succession law, the proportion of credentials of the previous partner will be passed on to the successor.12. If the percentage share among partners of a partnership firm is changed, but the partners remain the same, the credentials of the firm before such modification in the share will continue to be considered for the firm as it is without any change in their value. Further, in case a partner of partnership firm retires without taking away any credentials from the firm, the credentials of partnership firm shall remain the same as it is without any change in their value. 13. In a partnership firm "AB" of A&B partners, in case A also works as propriety firm "P" or partner in some other partnership firm "AX", credentials of A in propriety firm "P" or in other partnership firm "AX" earned after the date of becoming a partner of the firm AB shall not be added in partnership firm AB.14. In case a tenderer is LLP, the credentials of tenderer shall be worked out on above lines similar to a partnership firm. 15. In case company A is merged with company B, then company B would get the credentials of company A also.
Date of inviting tender shall be the date of publishing tender notice on IREPS website if tender is published on website or the date of publication in newspaper in case tender is not published on website.
Definition of Similar Work :-Any of the Following works are considered as similar nature of work--->>> (1)Track Circuit, (2)LVCD, (3)LC Gate Interlocking, (4)Electro-mech. Rehabilitation, (5)Panel Work (Outdoor), (6)Panel Work (Indoor), (7)Panel Work (Outdoor+Indoor), (8)RRI Work (Outdoor), (9)RRI Work (Indoor), (10)RRI Work (Outdoor+Indoor), (11)EI/SSI Work (Outdoor), (12)EI/SSI Work (Indoor), (13)EI/SSI Work (Outdoor+Indoor).
45 conditions · 8 needing a document upload
A copy of certificate stating that they are not liable to be disqualified and all their statements/documents submitted along with bid are true and factual. Standard format of certificate to be submitted by the bidder is enclosed as per Annexure V. In addition to Annexure-V, in case of other than Company/Proprietary firm, Annexure-V(A) shall also be submitted by the each member of a Partnership Firm/Joint Venture (JV)/Hindu Undivided Family (HUF)/Limited Liability Partnership (LLP) etc. as the case may be. Non submission of a copy of certificate by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he are/is qualifying the Qualifying Criteria mentioned in the Tender Document.
Payment of Supply Items: - Upon successful delivery at the designated Store, 80% of Agreement value of the supply items shall be paid. Balance 20% shall be released after successful execution/installation/commissioning of the items. (An undertaking regarding acceptance of payment conditions must be submitted at the time of bidding)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Mandate form containing PAN No. should be uploaded.
The Tenderer must go through the IR GCC- 2022 available in the documents section and submit the Documents regarding constitution of the firm viz.(i) Proprietorship affidavit/ declaration, Partnership Firm/Company/Joint Venture (JV)/Registered Society/Registered Trust, MOA (Memorandum of Association)/AOA(Articles of Association) of the company; and (ii)A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors)in favour of the individual to sign the tender on behalf of the company must be submitted by the Tenderer etc. In absence of such documents the tender shall be treated as having been submitted by the individual who has signed the tender. Besides the above the tenderer also has to submit a declaration regarding blacklisted/ not blacklisted
As per GCC-2022(i)The tenderer shall clearly specify whether the tender is submitted on his own(Proprietary Firm)or on behalf of a Partnership Firm/Company/Joint Venture (JV)/Registered Society/Registered Trust/HUF etc. The tenderer(s)shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be(ii)Following documents shall be submitted by the tenderer: a)Sole Proprietorship Firm:(i)An undertaking that he is not blacklisted or debarred by Railways or any other Ministry/Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which he was/is a partner/member. Concealment/wrong information in regard to above shall make the contract liable for determination under Clause 62 of the GCC of Contract(b)HUF:(i)A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF.(ii)An undertaking that the HUF is not blacklisted or debarred by Railways or any other Ministry/Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which HUF was/is a partner/member. Concealment/wrong information in regard to above shall make the contract liable for determination under Clause 62 of the GCC.(C)For partnership firm The Tenderer shall submit -(i)A notarized copy of partnership deed.(ii)A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm.(iii)An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry/ Department of the Govt. of India from participation in tenders/contracts as on the date of opening of bids, either in their individual capacity or in any firm in which they were / are partners. Concealment /wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.(D)Company registered under Companies Act 2013:(i)The copies of MOA(Memorandum of Association) / AOA (Articles of Association) of the company. (ii)A copy of Certificate of Incorporation.(iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.(iv)An undertaking that the Company is not blacklisted or debarred by Railways or any other Ministry/Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which the Company was/is a partner/member. Concealment/wrong information in regard to above shall make the contract able for determination underClause62GCC(e)Registered Society & Registered Trust and LLP-Tenderer shall submit documents as per Clause 14 of GCC-2022.
(I)If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture /Registered Company etc., then the tender shall be treated a s having been submitted by the individual who has signed the tender.(II)After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm/ Partnership Firm / Registered Company/ Registered Trust / Registered Society / HUF etc. shall be neither asked nor considered, if submitted. Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office file set c. will be taken for consideration of the tender, if no such mention is available in tender offer submitted. (III)A tender from JV / Partnership firm etc. shall be considered only where permissible as per the tender conditions. (IV)The Railway will not be bound by any change in the composition of the firm made subsequent to the submission of tender. Railway may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
The tenderer whether his own(Proprietary Firm)or on behalf of a Partnership Firm/Company/Joint Venture (JV)/Registered Society/Registered Trust/HUF etc shall also submit all documents as per instructions given in the General Conditions of contract- 2022(Second Sheet) wherever applicable. Tenderer are thus advised to read the same before submitting their bids and upload the required documents.
A declaration regarding engagement/employment/ partnership etc. (or Not) of retired Railway employees should be uploaded by the Tenderer.
The list of personnel/organization on hand and proposed to be engaged for the tendered work. Similarly list of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work.
The tenderers shall submit a copy of certificate stating that all their statements/documents submitted along with bid are true and factual. Standard format of certificate to be submitted by the bidder is enclosed as per Annexure V. In addition to Annexure-V, in case of other than Company/Proprietary firm, Annexure-V(A) shall also be submitted by the each member of a Partnership Firm/Joint Venture (JV)/Hindu Undivided Family (HUF)/Limited Liability Partnership (LLP) etc. as the case may be. Non submission of above certificate(s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents (if any) duly self attested. NOTE- Format of Annexure V is also enclosed in document Tab for references.
For Sole Proprietorship Firm: (i) An undertaking that he is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which he was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.
For Partnership Firm :-(i) A notarized copy of partnership deed. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm. (iii) An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of opening of bids, either in their individual capacity or in any firm in which they were / are partners. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.
For Company registered under Companies Act-2013 :- (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.All other documents in terms Para 10 of the Tender Form (Second Sheet of the GCC) (iv) An undertaking that the Company is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which the Company was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.
Registered Society & Registered Trust:(i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet of the GCC)
LLP (Limited Liability Partnership): (i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet of the GCC)
HUF- A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) An undertaking that the HUF is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which HUF was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract.
An undertaking by all partners/members of JV / HUF/proprietor etc, of the partnership firm or JV or HUF or Proprietorship Firm etc. as the case may be that they are not blacklisted or debarred by Railways or any other Ministry/ Department of the Govt. of India from participation in tenders/contracts as on the date of opening of bids, either in their individual capacity or in any firm in which they were / are partners/ members/Proprietors/HUF etc. as the case may be is to be submitted.
Clarification of Bids: To assist in the examination, evaluation & comparison and prequalification of the Tender, the Railway may, at its discretion, ask any Bidder for a clarification of its Bid. Any clarification submitted by a Bidder that is not in response to a request by the Railway shall not be entertained or considered. The Railway request for clarification and the response of the bidder in this regard shall be in writing. However, if a Bidder does not provide clarification of its bid by the date and time communicated in the Railway request for clarification, the bid shall be evaluated as per the documents submitted along with the bid.
The tenderer whether sole proprietor / a company or a partnership firm / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the Power of Attorney is being issued. However, the Power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Appostille certificate.
The Tender Form(First Sheet) available in the document section must be filled in by the tenderer and uploaded duly filled in.
The Tenderer must go through the Tender Form(Second Sheet) thoroughly and submit all the required documents even if not clearly mentioned in the Conditions or compliances in the Tender document.
Letter of Credit as Mode of Payment in Works Tender or Service Tender has been introduced as per Rly Board's letter no. 2018/CE-I/CT/9, New Delhi, dtd: 04.06.2018. The details in this regard are given in Special conditions of contract which may be seen by the tenderers before bidding in IREPS Portal.
Tenderers(s) should read carefully the instructions given in the Tender Form (Second Sheet) of Indian Railway Standard General Conditions of Contract-2022 and submit all the required documents in compliance to the Instructions containing in the said Tender Form (Second Sheet). A copy of the Indian Railway Standard General Conditions of Contract(GCC)- 2022 is available in the document section.
S&T work in connection with Development of a Crossing Station with Provision of an additional full length loop line between Tatanagar and Haludpukur.
ST-CKP-OT-26-27-86~SER
ST-CKP-OT-26-27-86
Open
Works - General
18 Months
West Singhbhum, Jharkhand
₹0
₹18.4 L
8 Sept 2026
8 Sept 2026
17 Sept 2026
201 items across 9 schedules · ₹9,21,67,302.34 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Excavation of trench in all kinds of soils including soft rocky area and clearing of roots of trees, rocks, bushes, ballast & reconditioning etc., including bailing out water and disposal of extra soil including back filling with excavated earth and ramming of trenches after cable laying for the following depths and widths as specified in Technical Circular No. 2 of 1988 & 01/2010 issued by CSTE/SER. Note:- In case, trenches are other than prescribed depth & width, Proportionate payment shall be released. (i) Depth 1.2 meter, Width 0.5 meter. | Kilometre | 25.00 | 78,680.04 | 19,67,001 |
| 2 | Excavation of trench in all kinds of soils including soft rocky area and clearing of roots of trees, rocks, bushes, ballast & reconditioning etc., including bailing out water and disposal of extra soil including back filling with excavated earth and ramming of trenches after cable laying for the following depths and widths as specified in Technical Circular No. 2 of 1988 & 01/2010 issued by CSTE/SER. Note:- In case, trenches are other than prescribed depth & width, Proportionate payment shall be released. (i) Depth 1.0 meter, Width 0.3 meter. | Kilometre | 5.00 | 69,727.38 | 3,48,636.9 |
| 3 | Laying of S&T Cables (Signal/Quad/Power) in the excavated trench t o D r a w i n g No. CON/SK/T/5. Transportation and supply of 'U' clamps, anchoring of cable at every 10 mtrs interval with 'U' clamp on trench to Drawing No. CSTE/CON/CABLES/81. Transportation, supply and placing of cable demarcating lead belt to Drawing No. CON/SK/T/6 punched at a n interval of 30 mtrs. and wrapped round each cable throughout the cable route and also at every track/Road/ platform crossing as above specified i n Technical Circular No. 2/1988 & 01/2010 issued by CSTE/SER and guarding the cables collecting empty drums with left over cable and return to the stores of stock holder. | Kilometre | 115.00 | 19,877.1 | 22,85,866.5 |
| 4 | Transportation o f c a b l e s i n r o l l s w i t h or without wooden drums ( S & T Cables) from Central Store(CKP)/concerned s t o r e t o the site of works. | Drum-Km | 115.00 | 2,286.84 | 2,62,986.6 |
| 5 | Termination of Outdoor Cables : (Main Cables/tail cables) at both ends in locaiton boxes, cable termination rack in relay room, staiton building, generator room etc. The item includes dressing of cables and wires with dressing threads as per standard practice. All material required for this item will be supplied by contractor. The out door cable shall be tarminated in Relay room , DG Room , ASM Room etc. under supervision and instrucitons issued by Engr. In-Charge of the work. Inspection by Consignee. Note: The Unit showns as Nos means per conductor. | Per Conductor | 8000.00 | 9.38 | 75,040 |
| 6 | Fixing of Q series relay base plate/metal to metal relaymini group and major group base plate, laying, bunching ,lacing, dressing & packeting of60/40 core PVC indoorcable/flexible wire andtermination of 60/40 corecable/flexible wire on tagblock/base plate & base plates& soldering. This includes fusewiring, bus bar looping etc.required for keepinginstallation ready for circuitwiring work & panelthroughing work. The workshall be done as per approvedplan, extant practice on ER &the instruction of Rly.Engineer at site. Inspection authority: - Consignee. | Numbers | 500.00 | 407.85 | 2,03,925 |
| 7 | Supply and placing of trunking and capping (RCC Duct) of 500 mm width as per Drg No. SOD/Cable laying/007 as detailed in document No. RDSO/SI/G/2010 ver.1.1 or latest on Guidelines on signalling cable laying, with the following modification Note: " The bottom thickness increased from 30mm to 40mm duly retaining overall height of 235 mm from ground level by keeping middle partition wall height at 195 mm from top surface of bottom wall of trunking and also to provide 3 nos long steel rods to make reinforcement design of capping to have improvement strength of capping. ( I n s p e c t i o n by representative of Sr. DSTE/CKP) | Numbers | 1000.00 | 1,546.38 | 15,46,380 |
| 8 | M i c r o Tu n n e l l i n g t h r o u g h Horizontal d i r e c t i o n a l drilling (HDD) machine, preparation of sites, boring and laying of HDPE pipes of size (outer/inner diameter= 50mm/42mm) for crossing o f S & T cable through HDPE pipe at bridges/culverts/track crossing/pucca road crossing, boring trench shall be minimum 3 (three) meter below the river bed and minimum 1 m at track/road/pucca road crossing area etc. This includes supply o f permanently lubricated HDPE telecom ducts of equal length as per Specification No. RDSO/SPN/TC/45/2013 REVISION 2 . 0 w ith latest amendments. For each HDPE duct the following items are to be supplied as per requirement (a) End plug (b) Cable sealing plugs (c) Plastic coupler slip fit/push fit type (d) End plugs to b e provided along w i t h drum. I n c a s e t h e site doesn't allow to perform as per schedule, written approval must be obtained from atleast site incharge officer.Note: The boring profile s h o u l d b e r e c o r d e d a n d s u b m it t e d for verification of depth and length of boring. (i) 4 HDPE pipe. | Metre | 750.00 | 1,928.12 | 14,46,090 |
| 9 | S u p p l y , t r a n s p o r t a t i o n a n d fi x i n g of Galvanised Iro n Pipe (make: TATA/Jindal or better) w i t h threaded collars (for jointing pipe) of 80 mm nominal bore Specification No. IS: 1239, thickness 3 . 2 m m medium grade, on bridges, culverts, drain or at places a s p e r instruction o f t h e site Engineer including supply and transportation of materials required for fixing the pipe as per SEM Drawing No.15-D7 including drawing of cables inside the pipe with masonry work at bridge entry and exit of the culvert and curing for 72 hours and pipes are to be clamped at max. 2 meter apart with drilling o f holes o n the pipe a t 1 0 c m apart for the following S&T Cables. The Galvanized iron pipes and other materials required for fixing t o b e supplied b y the contractor. Material inspection s h a l l b e d o n e b y Railway Site Engineer before use. This also includes dismantling of released GI Pipe/Trough and released material s h o u l d be returned at concerned store. (Inspection by representative of Sr. DSTE/CKP) | Metre | 1000.00 | 1,000.64 | 10,00,640 |
| 10 | Excavation of trench in all kinds of soils including soft rocky area and clearing of roots of trees, rocks etc. to a depth of 1 metre and width 0.3 mtr. For Track/ pucca road/platform crossing/ level crossing as per SEM Drawing No.15-D5 including supply, transportation and laying of DWC pipes (full) with collar(for jointing pipes) Inner diameter/Outer diameter:103mm/120mm to Specification No.14830 (Part- 2):2001 as per SEM Drawing No. 15-D4,in trench and drawing of cable through DWC pipes with collar(for jointing pipes) including back filling and ramming after cable laying as specified in Tech. Circular No. 2 of 1988 & 01/2010 issued by CSTE/SER for S&T Cables (Cable laying charges is included). This includes repairing and plastering of platform/pucca road after cable laying. Material inspection shall be done by Railway Site Engineer. | Metre | 750.00 | 679.68 | 5,09,760 |
| 11 | Execution o f Full Apparatus C a s e w i t h pit, concrete foundation, surrounding earth work, erection, installation as per Drawing No. Con/SK/T/8 and wiring as per S E M Drawing No.19-D8 or as per direction of site engineer. Fixing o f Hylam sheet strip o f size approx. 925mmx100mmx3mm ( i n c l u d i n g supply) with hole on both side for writing & terminal description, terminals, fuse blocks, relay and other accessories for signal/track circuit, termination o f cable with number embossed ferrules, bunching of cables with PVC tape, earthing of cable armour as required. Painting of the apparatus case inside and outside after clearing the surface thoroughly and first coating of anticorrosive paint and subsequent two c o a t s o f Aluminium paint outside a n d r e d oxide inside and lettering etc. This includes transportation of 25 mm/12mm Hylam sheet for shelf or as required and also includes minor modification in L/Boxes as per site requirement .The contractor shall supply of 4 no. of foundation bolts 22 mm dia. x 450 mm long with 2 flat spring washers, one nut is to be used for each set, sand for filling up cable pit inside the apparatus case and bolts, nuts, screws, M S C l a m p s f o r fixing equipment/cable. Note: - Part payment shall be released after completion of- (i) Foundation- 40%, (ii) Erection - 10%, (iii) Wiring, earthing, testing - 20%, (iv) Painting, writings - 10%, (v) Plastering, sand filling & etc. - 10%, (vi) Commissioning - 10%. | Numbers | 50.00 | 8,983.34 | 4,49,167 |
| 12 | Excavation o f earth pit, placing & fixing of Earth electrode with construction of cement enclosure to SEM Drawing N o . 1 9 - D 6 and drawal of 6 SWG GI/Copper cable from earth electrode t o goomties, r e l a y room, cabin, station, etc. and drawal of MS flat 35mm x 6mm for signal post/Location b o x shall be used as the case may be, including fixing at both ends of the wire/MS flat. This includes transportation o f materials. Note: Materials such as charcoals, salt, sal ammoniac, 6 SWG G I wire, copper lugs with Steel bolts & nuts etc. shall b e supplied b y the contractor. MS fl a t 3 5 m m x 6mm/Copper cable shall be supplied by Railway. | Numbers | 70.00 | 1,759.38 | 1,23,156.6 |
| 13 | Transportation, erection, fixing, installation and commissioning of Cable Termination rack (CTR), fixing of MS Wiring ladder from relay rack to CTR, and on to top of the CTR- including supply o f 3/6mm Hylam sheet of required size for fixing terminal blocks & writing terminal description, termination of cables, bunching of cables by PVC tape and earthing of cable armours, painting, lettering as required. The contractor shall draft terminal analysis chart on the white bond paper of appropriate size & supply wiring materials l i k e e y e l e t s o f s i z e s , trough, condensers and resistances a s p e r required value, HV protection cover with fixing top caps and danger symbol, soldering material of approved quality etc. shall be supplied by t h e contractor. Cement o f approved brand, stone chips 5/8" and sand as required for mounting CTR, Sand f o r filling of cable pit a n d other required masonry work, Sundry materials such as MS plate/angles, MS wiring ladders a s p e r approved Drawing, , Anchor bolt 5/8" X 9 " with nut and washers - 4 No., Nickel plated screws 2BA X1" with nuts and washers for fi x i n g Hylam sheet, numbers embossed ferrules 2.5 sq. mm, PVC bunching tapes and buttons, paint synthetic enamel of smoke grey colour for painting, MS clamps with bolts and nuts o f sizes, D-bracket and 60mm insulator, for fixing cables, screws of sizes as required shall be supplied by the contractor. Cables should be routed properly through ladder. All the materials required for installation, wiring, testing and commissioning a s p e r t h e approved wiring diagram except the materials included in supply schedule shall be supplied by the contractor. | Numbers | 12.00 | 51,014.94 | 6,12,179.28 |
| 14 | Transportation, installation a n d w i r i n g of Rotary key transmitters/KLCR on Hylam sheet b o a r d including wiring & fixing of push button bell switch on Hylam sheet of 12mm including termination, painting & lettering. The sundry materials such as Hylam sheet, push bell switch etc. to be supplied by contractor. | Numbers | 12.00 | 1,524.56 | 18,294.72 |
| 15 | Installation, testing & commissioning of Earth Leakage Detector (ELD) - 8 channels a s per Specification No. RDSO/SPN/ 256/2002 or latest. | Set | 6.00 | 5,841 | 35,046 |
| 16 | Transportation and installation of Electric point machine including lubrication a n d MS plate fi x e d o n concrete sleepers complete with fixing of anti-theft cover, crank handle key interlocking arrangements Junction boxes, ground connections including smithy works, insulation of M S plate o n which the point machines to be fixed from the gauge tie p l a t e involving riveting/welding of angle cleats, termination o f cable s, preliminary adjustment o f operation o f points b y crank handle, wiring, painting a n d lettering as required. Drilling of holes for fixing of switch extended bracket and leading stretcher bar. Note:- All the required nut-bolt, washer, MS- plate for anti-theft, eyelets, etc. for fixing of point machine to be supplied by contractor. | Numbers | 14.00 | 13,280.9 | 1,85,932.6 |
| 17 | Transportation, installation of 2-Aspect Signal P o s t for MACLS as per drawing no. Con/SK/T/12 or SEM-Drawing No. 19-D3 complete with signal units, base, ladder and other fittings, excavation of pit, erection of posts, casting concrete foundation thereof as specified in the note given in drawing, fixing of complete fittings of the signals with n e c e s s a r y e a r t h s c r e e n protection arrangement including termination of cables, painting and lettering as required. Foundation Bolts of size 24 mm x 915 mm as per RDSO Drawing No. SA-116 A/M confirming to IS: 226 and IRS:S-10/78 Rev.8. | Numbers | 10.00 | 10,595.22 | 1,05,952.2 |
| 18 | Transportation, installation o f 3 - Aspect Signal Post for MACLS as per Con/SK/T/12 or SEM-Drawing No. 19- D3 complete with signal u n i t s , b a s e , l a d d e r a n d other fittings, excavation o f pit, erection o f posts, casting concrete foundation thereof a s specified in the note given in drawing, fixing of complete fittings of the signals with necessary earth s c r e e n protection arrangement including termination of cables, painting and lettering as required. Foundation Bolts of size 24 mm x 915 mm as per RDSO Drawing No. SA-116 A/M confirming to IS: 226 and IRS:S-10/78 Rev.8. | Numbers | 6.00 | 11,313.84 | 67,883.04 |
| 19 | Transportation, Installation, Wiring, Testing & Commissioning of LED Signals Lamps for Main signals Lighting Unit (i.e. Red, Yellow, and Green) as per instruction of railway Engineer at the site.Note:- LED particulars such as aspect, make, type, Sr. No. etc. to be recorded in proper in proper register. | Numbers | 55.00 | 1,078.52 | 59,318.6 |
| 20 | Transportation a n d fi x i n g o f C a l l i n g ON Signals/ Dependent Shunt Signals / Illuminated 'A' / Illuminated 'AG' marker for MACLS o n the erected signal post complete with marker including termination of cables, painting and lettering as required. | Numbers | 16.00 | 2,324.6 | 37,193.6 |
| 21 | Transportation, installation of Position light Shunt Signal as per Con/SK/T/12 or SEM Drawing No. 19-D4 complete with units, base and other fittings, excavation o f pit, casting o f concrete foundation thereof as per note given in drawing, fixing in complete fittings of signal including termination of cables, painting and lettering as required. Foundation Bolts of size 20 mm x 305 mm as per RDSO Drawing No. SA-110 A/M confirming to IS: 226 and IRS:S- 10/78 Rev.8. | Numbers | 4.00 | 5,010.28 | 20,041.12 |
| 22 | Transportation a n d fi x i n g o f Junction type Route Indicator w i t h Ro u t e a r m o n the erected signal post including termination of cables, painting lettering as required. (i) Route Indicator with Route arm Two way. | Numbers | 4.00 | 933.38 | 3,733.52 |
| 23 | Transportation, Installation, Wiring, Testing & Commissioning of LED Signals Lamps for Subsidiary signals lighting unit (i.e. Route aspect, Shunt Signal, Calling on aspect, A marker etc.) as per instruction of railway Engineer at the site. | Numbers | 62.00 | 909.78 | 56,406.36 |
| 24 | Execution o f Straight joint o n Q u a d cable/ j e l l y filled Telecom c a b l e u s i n g Thermo- shrink/Universal jointing kit (RTSF). This includes excavation of cable joint pit of size 1.2m x 1.2m x 1.0m for jointing of cables, back filling and ramming after jointing. | Numbers | 25.00 | 1,411.28 | 35,282 |
| 25 | Design and supply o f the following drawings t o office records a s p e r requirement o f the Railways. This includes alteration at different stages and finally supply o f all the drawings including tracings within 90 days from the date of commissioning o f t h e w o r k . This includes t h e following drawings for each station: (1) Cable layout plan (Main) (2) Cable layout plan (Tail) (3) Cable matching chart (4) Location Hut drawing (5) Termination c h a r t o f e n d g o o m t i e s and location hut (6) Traction bonding plan (7) Contact Analysis Chart (8) SWRD & GWRD (9) Equipment Layout P l a n (10) Power Supply arrangement diagram (11) Any other drawing as found relevant as per site condition. Office record include the following: ( i ) Battery History book (ii) Track Circuiting Register. (iii) Track circuit maintenance Register. (iv) Cable Meggering Register (v) S i g n a l History Register ( v i ) LED Register (vii)Glued joint/ Block joint Register (viii) Point machine Maintenance Register .(ix) Joint Inspection Register such as P. Way, Electrical & S i g n a l . ( x ) Re l a y Register (xi) Route cancellation Register (xii) Relay Ro o m Key Register (xiii) Emergency Point operation Register. (xiv) Crank Handle Register (xv) Emergency Route Cancellation Register (xvi) Axle counter reset register. Note:- (i) All the diagram will be made on CAD. The paper size of wiring diagram will be A-3 and minimum tex t size o f 2 m m should b e used. Wiring diagram will be made in 'Black colour'. Alteration to wiring diagram will be done using TWO drawing method' RED and Green colouring s h o u l d b e u s e d o n production copies of design detail to indicate changes as follows: RED = new equipment to be installed o r commissioned. G R E E N = redundant equipment to be recovered. (i) Up to 5 line yard. | Station | 1.00 | 38,045.56 | 38,045.56 |
| 26 | Design of Route Control Chart (RCC), Front Plate Diagram (FPD) and circuits for Panel Interlocking as per approved Signal Interlocking Plan and typical circuit diagram. Wiring diagram shall be made in 'Black Colour' and Alteration to wiring diagram with Red for new installation and green for deletion contact/equipment. All the drawing and design shall include the copy of production checking, independent checking, first & second level checking, and commissioning copy. Submission of Two sets of prints with all correction for Railway's approval. Approved copy (06 Sets) of all drawings in plastic folders along with the original tracings in spiral bound with editable Auto-CAD copy latest version. This includes the following drawings for each station: (1) Cable layout plan (Main) (2) Cable layout plan (Tail) (3) Cable matching chart (4) Location Hut drawing (5) Termination chart of end goomties and location hut (6) Traction bonding plan (7) Contact Analysis Chart (8) SWRD & GWRD (9) Equipment Layout Plan (10) Power Supply arrangement diagram (11) Any other drawing as found relevant as per site condition. Office record include the following: (i) Battery History book (ii) Track Circuiting Register. (iii) Track circuit maintenance Register. (iv) Cable Meggering Register (v) Signal History Register (vi) Lamp Register (vii)Glued joint/Block joint Register (viii) Point machine Maintenance Register . (ix) Joint Inspection Register (a) P. Way, Electrical & Signal. (x) Relay Register (xi) Route cancellation Register (xii) Relay Room Key Register (xiii) Emergency Point operation Register. (xiv) Crank Handle Register (xv) Emergency Route Cancellation Register (xvi) Axle counter reset register. (i) Up to 5 line yard. | Station | 1.00 | 1,13,117.16 | 1,13,117.16 |
| 27 | Installation of Single Maintenance Free Earth pit as per RDSO Drawing No. SDO / RDSO/ E&B/001 which includes the following:-a) Digging/Auguring/Boring of single earth pit of 1 0 0 m m t o 1 2 5 m m d i a . t o t h e d e p t h of approx. 3 meter. b) Insertion of 3.0 meter electrode and penetrating it minimum 150 mm by pushing gently with sledge hammer where the natural soil i s assumed. (c) Filling of earth pit with Earth Enhancement Compound (EEC) i n s l u r r y f o r m and backfilling. (d) Carrying out exothermic weld connection on single earth electrode to a copper tape of 200 x 25 x 6 mm. (e) Carrying out exothermic weld connection on the copper tape of 200 x 25 x 6 mm on Earth Electrode for connecting two 35 Sq. mm cables f o r redundancy. ( f ) T h e exothermic welding material for bonding the earth system shall be procured f r o m RDSO approved fi r m s , w h i c h includes graphite modules, clamps, weld metal powders. (g) The dimension of the chamber will be of 300 x 300 x 300 mm (inside dimension) o f RCC with 50mm thick a n d fine finish, Inspection chamber should be as per IEC 62561-5 or latest. T h e t o p R C C c o v e r s i z e s h a l l be 400mmX400mmX50mm. The date of testing and earth resistance value shall be written on the cover with black base with yellow paint. | Set | 56.00 | 5,989.68 | 3,35,422.08 |
| 28 | Digging a trench to a minimum depth of 0.5 meter and laying 50x6 m m bare Galvanized steel tape (Interconnecting tape) connecting a l l t h e earth pits. Routing a n d laying 50x6 mm Galvanized steel tape connecting all the e a r t h p i t s . Carrying o u t exothermic weld connections o n a l l t h e earth electrodes to Galvanized steel tape o f size 5 0 x 6 m m for interconnecting the earth pits. It shall be ensured that the distance between any two earth electrodes shall be minimum 3 meter (length of the earth electrode) and max up to 6 m e t e r ( t w i c e t h e l e n g t h o f t h e earth electrode) to avoid mutual resistance effects. This interconnecting t a p e s h a l l a l s o be covered with approximately 30 Kg of earth enhancing compound for each 3 meters length. Earth enhancement compound 10Kg along each meter also t o b e spreaded along the Galvanized steel tape. | Metre | 350.00 | 88.5 | 30,975 |
| 29 | Transportation, Grouting/erection, wiring as per approved wiring diagram of 19" relay rack/Composite/Q- Series Relay Rack with subsequent alteration (with 3/4 X 9" anchor bolts with one nut and one washer per bolt & D-bracket & 60mm insulator), fixing of M.S. ladder as per requirement for rack to rack connection, CTR and control panel, fixing of p l u g b o a r d s , r e l a y s , t e r m i n a l blocks, terminals, filter units, tag blocks, fuses, bus bars, shelves, strips, 6 m m Hylam sheet of r e q u i r e d l e n g t h f o r writing terminal description etc. fixing and termination of cables on t h e r e l a y r a c k s w i t h number embossed ferrules, bunching o f cables with PVC tape, earthing of cable armour including painting and lettering. Wiring and testing of complete relay rack accommodating all relays as per wiring diagram. All materials such as eyelets, M.S ladder, Hylam sheets, ferrules, trough etc., if required for modification of rack shall be supplied by the contractor and to be carried out at site within the cost. | Numbers | 12.00 | 46,785.82 | 5,61,429.84 |
| 30 | Alterations/modifications works on existing relay rack (Q- series/ Composite Relay Racks)/Cable Termination Racks (CTR) including works of installation, wiring, termination, testing and commissioning. The work includes fixing of aluminium/steel/M. S ladder along with supply a s per requirement t o accommodate additional p l u g board, r e l a y s , terminals/blocks, t e r m i n a l s , tag blocks, fuses, transformers, b u s b a r s , TW shelves/strips e t c . i n the existing relay racks/CTR's, 6 mm Hylam sheets of required length f o r writing terminal description etc. fixing and termination of cables o n the relay racks, CTR's with number embossed ferrules, bunching of cables with PVC tapes, earthing o f cable armours, covers including painting and lettering, making anti tilting arrangement. Note:- a) Existing relay rack (Q- series/ Composite Relay Racks) : Payments for alterations in existing relays upto 20 nos. relays & above 20 nos. shall be made 50% & 100% respectively. b) C a b l e Termination R a c k s (CTR):- Payments for alterations in existing C T R upto 1 2 0 cores & above 120 nos. cores shall be made 50% & 100% respectively. | Numbers | 6.00 | 20,844.7 | 1,25,068.2 |
| 31 | Transportation, installation and painting with retro reflective tape of SLB/BSLB/Legend/Stop Board etc. as per SEM Drawing No. 19-D4. This includes i) Excavation of pit of depth 900 mm, width 600 mm. ii) casting in the ratio o f cement c o n c r e t e m i x t u r e s h a l l b e 1 : 3 : 6 iii) foundation, (iv)Erection etc. Note: Supply of sighting board by contractor to be as per SEM Drawing No. 12-D1 or specified by Railway. | Numbers | 2.00 | 8,382.72 | 16,765.44 |
| 32 | Alteration/modification in existing location boxes, fixing of equipments, cable insertion, termination, wiring, testing & commissioning, two coat painting, lettering to suit the circuits a s p e r a p p r o v e d w i r i n g d i a g r a m . This includes filling with sand a n d plastering the same. Note: All the sundry materials except t h a t included in supply schedule shall be supplied by the contractor. | Numbers | 10.00 | 2,685.68 | 26,856.8 |
| 33 | Installation, Wiring, Testing, Validation and commissioning of Data logger with 1024 Digital and 64 Analog inputs with modem as per Specification No. IRS:S-99/2006 (Amdt-3) or latest. | Set | 1.00 | 45,539.74 | 45,539.74 |
| 34 | Installation, Wiring, Testing, Validation & and commissioning o f D a t a l o g g e r w i t h 512 Digital and 32 Analog input with modem as per Specification No. IRS:S- 99/2006 (Amdt-3) or latest. | Set | 3.00 | 38,891.62 | 1,16,674.86 |
| 35 | Transportation, installation, testing and commissioning of M a g n e t o Portable Telephone (desk type) a s per specification IRS/TC/79/2000 including supply of dry cell batteries. | Numbers | 10.00 | 246.62 | 2,466.2 |
| 36 | C e m e n t C o n c r e t e o f p r o p o r t i o n 1:3:6 ( C e m e n t : Sand: Stone c h i p s o f 25mm nominal s i z e ) f o r miscellaneous items. It includes excavation, ramming of CC by using vibrator, curing a n d plastering with cement and sand mixture (aggregate will not exceed beyond 3.8 cm). Note: All materials required f o r foundation a r e t o be supplied by the contractor. | cum | 70.00 | 3,582.48 | 2,50,773.6 |
| 37 | Miscellaneous arrangements for NI period comprising of a) Temporary goomty/Tent of dimension atleast 12'x12' at both side of the station yard a n d a t central panel building, furnished with one table, six chairs, emergency light a n d mosquito repellent. b) Sufficient temporary lighting arrangement throughout the yard from Sunset t o sunrise one dayprior, during and post NI work. This includes provision of two DG set of minimum 7.5 KVA capacity and halogen flood lights. T h e D G s e t s a n d Diesel etc. has to be arranged by the contractor at his own cost. c) Provision of PA System at both the end of the yard. d) Resting arrangement for atleast 16 staff at night. e) Vehicle for transportation for to and fro movement of S&T staff during N I period. f) Manning of adjacent station to be done by contractor. g) Provision of printing/Xerox copies of drawings, wiring diagram, CTR/ Location box terminal chart, point wiring, MSDAC/track circuit wiring, NI program, Signal wiring, track bonding plan, etc. in a plastic folder. No. of copies depends upon the number of team formed for NI and as per instruction of officer in-charge of NI. h) This also includes Free home & Free Starter wiring for NI as per the instruction of site engineer. (i) Up to 200 Routes. | Station | 1.00 | 1,14,548.5 | 1,14,548.5 |
| 38 | Mechanised Drilling/ Micro Tunnelling under important/ busy metal/concrete road /Railway track and laying GI pipe (make: TATA/Jindal or better) min. 75mm inner diameter Grade Medium w i t h Specn.No.IS- 1239, Pt-1, 1979 including supply), Boring and pulling cable upto 110mm dia. at a depth of min. 1 meter as per site condition. This also includes reinstatement of the surface to the original state. | Metre | 500.00 | 2,174.74 | 10,87,370 |
| 39 | Installation, Testing and Commissioning of SMPS based Integrated Power Supply System (Mini- IPS) as per Specification No. RDSO/SPN/165/2012 Ver. 3.0 or latest and conforming to SE Railway Drawing No.SK/DRG/OL/SER/237, dated 23.01.19. | Set | 3.00 | 59,000 | 1,77,000 |
| 40 | Installation, Testing and Commissioning of SMPS based Integrated Power Supply System (Large-IPS) as per Specification No. RDSO/SPN/165/2012 Ver. 3.0 or latest and conforming to SE Railway Drawing No. SK/DRG/OL/SER/253, dated 23.01.19. | Set | 1.00 | 59,000 | 59,000 |
| 41 | Transportation, grouting and laddering of Integrated Power Supply (IPS) System including termination of power & signalling cables on Hylam sheet fixing on MS angle by contractor on wall in panel room, IPS room of adequate size duly fixed with galvanized MS clamp, ladder, painting & lettering. Note: Transportation of batteries, electrolyte, bolts & nuts, screws, trough etc. and other sundry materials required for the above work shall be supplied by the contractor as required. The IPS to be commissioned by the OEM. | Set | 4.00 | 43,095.96 | 1,72,383.84 |
| 42 | Supply and Installation of Glass fronted Key box made of water resistant Engineered wood for Rotary key transmitters (RKT)/EKT/KLCR/ SM's key box of appropriate size etc. with locking arrangement and 1 no. of Godrej make or better padlock it should be done as per site supervisor instructions. After installation it should be painted and letter writing as per SER practice. (Inspection by representative of Sr. DSTE/CKP) | Numbers | 4.00 | 2,259.7 | 9,038.8 |
| 43 | Installation, Testing and Commissioning of solid state Block Proving by Axle Counter (BPAC) using Block Panel and UFSBI for Single line operation complete with all accessories as per Specification No. IRS:S- 175/2005 (Ver.1) or latest. | Set | 2.00 | 88,040.98 | 1,76,081.96 |
| 44 | Providing brick masonry in ratio 1:6 cement & mortar including plastering with 1:4 cement & sand mixture both side, 20mm thick each with contractors own class-II bricks including excavation, curing, grouting, bolting etc. wherever required. Bricks, sand & cement to be supplied by the contractor. | cum | 10.00 | 2,011.9 | 20,119 |
| 45 | Loading/Unloading & transportation of IPS from store to the execution site. Note: The unit shown as "Numbers" means "Trip". (As decided by the Site engineer) | Numbers | 4.00 | 19,608.08 | 78,432.32 |
| 46 | Installation, Testing & Commissioning of Single Section Digital Axle Counter phase reversal type as per Specification No. RDSO/SPN/177/ 2012 Ver.3 or latest without tool kit. | Set | 4.00 | 52,902.94 | 2,11,611.76 |
| 47 | Transportation and fixing of following types of C.T. Box (Aluminium/Wago type) and termination of cable as per details of jointing schedule approved by the Railway Engineers. (i)20 pair C.T. Box. | Numbers | 15.00 | 899.16 | 13,487.4 |
| 48 | Designing and Plotting of Signalling Interlocking Plan (SIP) in AUTOCAD. Two copies of prints with soft copy will be submitted to Railway for checking. If alterations are suggested/proposed by Railways then again two copies of prints will be submitted for advance approval after carrying out all the alterations as suggested/proposed by the Railways. Tracings will be submitted for all the diagrams mentioned above for the purpose of approval by Railway prior to commissioning of station. | Per SIP | 1.00 | 28,072 | 28,072 |
| 49 | Preparation of Station Working Rules (SWR) in English on the basis of station working rule diagram and gate working rule diagram to be supplied by the contractor. Submission of two draft copy to railway for checking and resubmission of draft in three copies for approval of division after making corrections. Editable Soft copy to be supplied in pen drive. | Set | 1.00 | 13,595 | 13,595 |
| 50 | Preparation of Station Working Rules (SWR) in Hindi/Regional Language of that station on the basis of station working rule diagram and gate working rule diagram to be supplied by the contractor. Submission of two draft copy to railway for checking and resubmission of draft in three copies for approval of division after making corrections. Editable Soft copy to be supplied in pen drive. | Set | 1.00 | 13,595 | 13,595 |
| 51 | Installation, painting/lettering, testing and commissioning of E-Type lock in sliding type LC gate with proper interlocking arrangement as directed by railway representative during work. All sundry materials like MS plates for fixing of E-type lock, various sizes of nuts and bolts to be supplied by the contractor. Drilling of holes for installation of E-Type lock and wherever required to be done by the contractor. | Numbers | 25.00 | 875.87 | 21,896.75 |
| 52 | Supply, Installation and commissioning of door close/open monitoring system as per direction of Railway's Engineer. (Inspection by representative of Sr. DSTE/CKP) | Set | 4.00 | 4,621.7 | 18,486.8 |
| 53 | Supply of Jointing materials for OFC suitable for jointing the Cable supplied complete and installation of O.F. Cable joint enclosure and Tenderers to enclose list of items, prices of jointing and manufacturer's name. This includes supply and installation of O.F. Cable jointing enclosure and splicing of optical fibre cable (18/24 Fibre) and testing. This also includes providing of pit as detailed in technical specification and advised by Engineer at site. The Joint enclosure shall be of Raychem/3M/TVSE/Roxtec make as per advice by the Engineer in charge of Railways. All materials to be inspected by consignee. (Inspection by representative of Sr. DSTE/CKP) | Numbers | 2.00 | 43,398.46 | 86,796.92 |
| 54 | Supply and installation of OFC Termination Box as per Specfication DOT/G/FIB-01/01 J a n . 9 3 and splicing of Optic fibre cables (18/24 Fibre) inside the termination box and with provision of take out all fibre of OFC and testing. This includes supply of installation accessories i.e.(pigtail with connector)etc. as detailed in technical specification and advised by Railway's engineer at site. Insp Rep of Sr.DSTE/CKP NOTE : (i) 10% spare to be supplied additionally within the cost by the Contractor to Rly. (Inspection by representative of Sr. DSTE/CKP) | Numbers | 2.00 | 35,464.88 | 70,929.76 |
| 55 | Supply and installation of splice/pull through chambers: Details RCC Chamber of 950mm(L)x950mm(W)x1250 mm(H) with 100 mm thick inner walls, 100 mm thick bottom slabs and 150 mm thick split type top cover as per drawing, including excavation of all types of soil, dewattering, disposal of surplus excavated earth, laying of PCC, provising opening of ducts/sealing of opening after laying of ducts and precasting, backfilling from outside. (Inspection by representative of Sr. DSTE/CKP) | Numbers | 2.00 | 9,887.77 | 19,775.54 |
| 56 | Supply & Erection of Rack /Furniture for VDU as per appproved drawing for two VDU sets, two operators and one module for storage of records and files. Supply items to be inspected by representative of Sr.DSTE/CKP. | Numbers | 1.00 | 1,38,587.48 | 1,38,587.48 |
| 57 | Manufacture, supply and transportation of Block Cupboard, installation of Block panels on Block Cupboard, Cable termination on terminals, wiring, painting, lettering, testing and commissioning of Block panels, block telephones etc. as per the instruction of the Railway's representative. Note:- All the materials required for installation, wiring and commissioning of Block Panels (other than Block Panels and those materials included in Schedule "B" of the contract for supply of materials) will have to be supplied by the contractor.The sundry materials such as Block Cupboard as per the drawing supplied by the Railway, nuts & bolts,screws of sizes, eyelets of sizes, PVC bunching tape and buttons, numbered ferrules, Hylum sheets, teak wood planks and other such sundry materials required for the work to be supplied by the contractor. Insection of supply items by representative of Sr.DSTE/CKP. | Pair | 1.00 | 28,596.8 | 28,596.8 |
| 58 | Supply, Transportation, Intstallation and commissioning of Copper Plate Earthing System complete with provison of (i) Copper plate 300 mm x 300 mm x 3 mm. (ii) Earth Pit (8 to 10 ft.in depth) filled up with Charcoal (10 Kg) and salt (25 Kg) in layers. (iii) Water funnel on GI Pipe (iv) Cast iron Top Plate (12" x 12") (v) Drawing of Copper-Earth, from Earth Pit to location with 25 mm x 3 mm Copper Strip for termination in the OFC hut Earth Bus Bar. N.B: All the require materials for execution of the work shall be supplied by the contractor. The work to be commissioned as per diretion of Rly.'s Supervisor-in-charge. (Inspection by representative of Sr. DSTE/CKP) | Numbers | 20.00 | 9,892.2 | 1,97,844 |
| 59 | Online Monitoring, REMOTE DIAGNOSTIC AND PREDICTIVE MAINTAINENACE SYSTEM of RAILWAY SIGNALING GEARS. Details of the Item-wise Breakup are as per Annexure-A3. | Station | 1.00 | 70,14,335.62 | 70,14,335.62 |
| 60 | Supply, transportation, installation and commissioning of Fire Alarm System. Details of the Item-wise Breakup are as per Annexure-A2. (Inspection by RDSO). | Lumpsum | 1.00 | 9,46,012.78 | 9,46,012.78 |
| Schedule total | ₹2,38,36,645.15 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Annexure-1and2.pdf
ATTACHMENT
Annexure-L.pdf
ATTACHMENT
Annexure-MandN.pdf
ATTACHMENT
Anneure-V.pdf
ATTACHMENT
AnnexureVIA.pdf
ATTACHMENT
Annexure-VI-B.pdf
ATTACHMENT
Annexure-VA.pdf
ATTACHMENT
Annexure-Z.pdf
ATTACHMENT
TENDERFORMFirstSheet.pdf
ATTACHMENT
ColouredFinal_GCC_April-22_pdf_27.04.22.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo.11..pdf
ATTACHMENT
AnnexuresforMSDAC.pdf
ATTACHMENT
IPSspecificationwithtoolAnnexureIandIV.pdf
ATTACHMENT
RDSOGuidelinesforRevisedTANforEarthingetc.installation_80dpi_80.pdf
ATTACHMENT
RevisedTANforMSDACdated06062026.pdf
ATTACHMENT
Annexure-A2FireAlarm.pdf
ATTACHMENT
Annexure-A3OnlineMonitoring.pdf
ATTACHMENT
Annexure-G.pdf
ATTACHMENT
SpecialConditionsofContract.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .