SPECIAL REPAIR TO BLDG NO P-198 MD ACCN AND CERTAIN REVENUE / MINOR WORKS UNDER GE SHIKARGARH

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc; overall thickness and removing the dust debris etc to a distance not exc 250 meter from site and disposing the same complete all as specified and as directed by Engineer in charge.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Rendering 10mm thick in 1:4 mixed with integral water proofing liquid compound all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement. Note : (WPC shall be measured separately and paid for under respective item of schedule). (ii) First coat of bitumen primer confirming to IS 3384 @0.300 Kg/ Sqm over plastered surafces (iii) Second layer of 3.0 mm thick APP modified polymeric membrane with centre core of Single non woven polyster reinforcement and having weight 3.6 Kg/ Sqm with mineral gravel finish on top complete laid with blown type bitumen grade 85/25 @ 1.20 Kg/ Sqm complete all as specified and as directed. (iv) Finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against UV, including preparing of surfaces of roof (second coat applied after 24 hrs or as per manufacturing instructions).

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregates as over roof for making good depression/ undulation to make the existing roof surfaces plane as filling in depression of roof slab/ floor padding or as in roof kerbs rounded etc complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregates or as in roof kerbs rounded complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-1,using 20mm graded stone aggregates as in coping to parapet walls including necessary formwork complete all as specified and as directed.

Supply only integral water proofing liquid ISI marked Make: Pidiproof LW or equivalent

Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site all as specified and as directed.

Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specifide.

M&L for non skid ceramic tiles 10mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for non skid ceramic tiles 10mm thick (square/ rectangular) as in skirting / dado, Cut out of ceramic tiles of size exceeding 0.11 sqm but not exceeding 0.38 sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles of approved shade and pattern, 7 to 8 mm thick , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm laid in floor, set and jointed (square/ rectangular) in neat cement slurry and pointed in cement mixed with pigment to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in cement to mixed with pigment match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20 mm (+ 2mm) thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for mirror polished machine cut Kota stone slab 15-16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed.

M&L for 16 -18mm thick granite (black colour) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms and like, moulding of edges, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and as directed.

M&L for Jodhpur stone slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted (vertical or horrizontal) and set, jointed and grouted cement mortar 1:3 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab complete complete all as specified and as directed.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified.

M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified.

M&L for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg/Sqcm, of shape and colour as approved by GE , laid over 25mm thick compacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed.

M&L for factory made precast cement concrete solid blocks M-30 Grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size (with plain or interlocking joints as directed) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground around blocks and removal of rubbish/ surplus soil etc., complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified.

Demolition of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work, serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed.

M&L for squared rubble walling jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

-ditto- all as per above item but, except stone complete all as specified and as directed.

M&L for providing precast cement concrete block masonary 1:3:6 with solid blocks exc 10cm in width and setting in cement mortar 1:6 all as specified and as directed.

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.

Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed

M&L for rendering 15 mm thick in CM 1:6 over stone masonary, concrete surfaces, finished even and smooth (without using extra cement), all as specified and as directed.

M&L for 15 mm thick rendering on stone masonary wall surfaces in CM 1:4 finished fair and even all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for carrying out water proofing treatment for sunken portion in the following stages - (i) Taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces, washing down with water and rubbish of the pemises , cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00kg/sqm and grouting 25mm thick cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate on sunken slab portion and finishing the top surfaces even and smooth without using extra cement. (ii) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXITpidifin 2k manufactured by M/s Pidilite Industries Ltd or equivalent) and followed by a overlay protective screed (10mm thick cement mortar (1:4) along with liquid water proofing compound approved make as per manufacturer's instructions) on top surfaces of sunken slab after preprations as mentioned above. Method of application for acrylic cementitious water proofing coating achieved as per manufacturers instruction complete all as specified and directed.

Dismantling cast iron work of any description and in any position complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

Fixing only in repair 100mm bore any type of soil, waste and vent pipes in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

Fixing only in repair 100mm bore any type of soil, waste and vent pipes in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

Fixing only in repair 75mm bore any type of soil, waste and vent pipes in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

Fixing only in repair 75mm bore any type of soil, waste and vent pipes in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 100mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 75mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 100mm bore pipe cast iron cowls, complete all as specified.

Fixing only in repair 100mm bore pipe cast iron or any type cowls, complete all as specified.

S&F 75mm bore pipe cast iron cowls, complete all as specified.

Fixing only in repair 75mm bore pipe cast iron or any type cowls, complete all as specified.

M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified.

Fixing only in repair any type or cast iron up 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified.

M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) applied as per manufacturing instructions, complete all as specified.

M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) applied as per manufacturing instructions, complete all as specified.

S&F for 100mm bore pipes stack clamps out of 50mm by 3mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

S&F for 75mm bore pipes stack clamps out of 50mm by 3mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

M&L cement concrete type E-2, 1:5:10 (40mm graded crushed stone aggregate) as in sunken portion complete all as specified.

S&F 40mm bore steel water tubing medium grade galvanised inserted at the end of lateral slope projecting at least 15cm beyond the outer most projected part of the building below the drain pipe up to two storey construction as spout for sunken complete all as specifide.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.00 sqm each and removing from site or to store as directed by Engineer incharge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site or to store as directed by Engineer incharge.

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and removing from site or to store as directed by Engineer incharge.

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing the shutter in same opening after easing and adjusting complete as directed by Engineer incharge.

S&F Pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

S&F Pressed steel framed made out of 1.25mm thick MS sheet, of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc., complete all as specified

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary form work complete all as specified

M&L for Factory made 35 mm thick Plain framed, panelled shutters (two panel) with 2nd class hard wood rail and style with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified.

M&L for Factory made 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified.

S&F of Factory made steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8/10mm square bars as directed by Engineer incharge, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. (with provision of fixing for cooler if required) all as shown on drawing No CEJZ/TD/20 sheet 1/3 to 3/3 fixed in repairs i.e, incl taking down and removal of old steel windows from site or to store complete all as specified and directed. Note:- Guard bar/ grill shall be measured and paid separately under respective item of Sch 'A'.

M & L for aluminium powder coated ventilators (with louveres) fabricated with anodized aluminium rectangular section in frame & with deco grill of approved design & stainless steel wire cloth on the outer side of frame & trade pattern louvers with suitable mechanism for tilting /opening closing etc all as per sample kept in GE office & fixed in position complete all as directed. (Note : Glass pane in louvers & stainless steel wire cloth shall be measured & paid separately)

S&F Sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed.

.-Ditto- all as per above item but 4mm thick frosted glass complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed.

Mild steel round bars welded to steel windows or ventilators as in guard bars framed or unframed complete all as specified & as directed by Engineer incharge. Note: - Guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. Cost of factory welding & Shop coat of primer is deemed to be included in quoted rates.

S&F Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cementas specified MSSR. Make : Rajshree Doors or equivalent as approved by GE.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as specified in SSR. Make : Rajshree Doors or equivalent as approved by GE.

S & F 100 mm size PVC/ Stainless Steel (as approved by Engineer incharge) butt hinges all as specified and directed.

S&F mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified.

S&F Mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified.

S&F 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified.

S&F Mild steel rat tail rod pattern helical door spring of size 300mm including roller and roller plate fixing to iron frame by welding complete all as specified & as directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise specifically provided for (framed/ unframed work) complete all as specified.

S&F framed work as in doors chowkats of MS angle iron or MS hollow square/ rectangular any type/ size with gusset plates, rails, braces,cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to FE- 290 (Gde-E- 165) complete all as specified and directed by Engineer-in-charge.

S&F MS Pipes 150mm dia heavy weight (C-Class) using as structural work (single piece) erection with base/ top plate (thickness of bottom side plate is 16mm and thickness of top side plate 10mm), using 16mm bolt 300mm long double nut & washers four number each including welding throughout with medium channels (MC-100) with one priming coat etc; as directed complete all as specified.

M&L for RCC 1:1-1/2:3 Type A-1 using 20mm graded stone aggregate as in foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc as in mass concrete complete all as specified.

M&L for TMT bar 10mm dia & over cut to length,bent to shape as required annealed with mild steel wire not less than 0.9mm dia.

M&L for Form work to sides of concrete foundation, footing, base of columns, raft and raft beams, sides and soffits of foundation and plinth beams; and similar work etc; complete all as spesified.

S&F Pressed steel rectangular frames for built in cup board doors,(Godrej Pattern) made out mild steel sheet 1.25mm thick with girth of frame 185mm including necessary MS rawal plugs and fixing 75mm long butt hinges medium weight cold rolled mild steel etc including applying a shop coat of Zinc chromate primer all complete as specified .

S&F Pressed steel door shutters including stiffners made out of mild steel sheet 1.25 mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angles etc as required and applying a shop coat of zinc chromate primer all as per Godrej Pattern and as directed by Engr-in-Charge. Note: (i) Measurement of door shutter shall be taken as exact size of cup board opening (excluding door frame and folded/turned up portions). (ii) Stiffners of 150mm girth and height equal to height of shutter mode to shape as directed by EIC shall be provide to each leaf. Cost of these stiffners shall be deemed to be included in the unit rate quoted for door shutters and no extra measurement/ payment shall be made for the same. complete all as specified.

S&F Pressed steel shelves made out of mild steel sheet 1.25mm thick cut to size, holes punched including bending or turning up all around, mitered angles etc as required and applying a shop coat of zinc chromate primer all as per Godrej pattern and as directed by Engr-in-Charge (shelves shall be fixed to wall with required Nos of cadmium plated screws using PVC rawl plugs) Note : (i) Measurement of shelves shall be taken as exact horizontal inner size of cup board (excluding folded/turned up portions) complete all as specified.

S&F Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm (Make Godrej/Harison/Navtal) including MS chromium plated handle and 2 Nos MS locking rods out of 10mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick all as per Godrej pattern and as directed by EIC complete all as specified.

S&F Supply and fixing Stainless steel decorative type hanging rod of MS pipe 19mm bore having 1.6mm wall thick in any length (as per sample) complete all as specified and as directed. Note: - Each curtain rod to be provided with one pair of brackets trade pattern suitable for 19mm bore hanging rod fixed to wall (brackets shall be fixed to wall with MS Chromium plated screws using PVC rawl plugs) complete all as specified.

S&F Prelaminated particle board 18/ 19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work with wooden beading as required fixed in repairs i.e., including taking down and removal of old unserviceable boarding of any description and in any position complete all as specified and as directed.

S&F 2nd class hard wood plain fillets, square rectangular or triangular in section, wrought bullnozed , rounded or chamferred on one edge or face fixed with nails not exc 3 sqcm complete.

S&F Continous (piano) hings mild steel bright finish or elecrogalvanised fixed in repair Width of Flap 40 mm when open complete.

S&F ball catches with 8mm dia steel ball and brass body and stiking plate incluing letting and fixed in repairs.

S&F alluminium anodised handles 100 mm long fixed to windows all as specified and directed.

S&F 50mm dia polished hard wood knobs fixed with screw complete fixed in repairs.

S&F Decorative mild steel curtain rods 32mm dia (powder/PVC coated) including fixing brackets & side cups complete fixed in repairs i.e., including taking down the existing unserviceable curtain rods complete all as specified and directed

S&F Powder coated aluminium anodised decogrill weighing not less than 1.40 kg/ sqm and fixing necessary joining cleats/ frame etc; complete all as specified.

Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Taking down 20mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Taking down 25mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specifide.

Supply, fixing, Jointing and testing 15 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed

Supply, fixing, Jointing and testing 20 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed

Supply, fixing, Jointing and testing 25 mm bore galvanised mild steel water tubing 'medium grade' with and including all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed

Fixing only 15mm bore steel water tubing any grade with all New ISI marked fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Fixing only 20mm bore steel water tubing any grade with all New ISI marks fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

Fixing only 25mm bore steel water tubing any grade with new all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide.

S&F Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flush pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified.

S&F PVC 10 ltr. Cap. valveless syphonic action type, flushing cistern, low level, white/ coloured with inlet, ball valve, float and handle including brackets flush pipe 32 mm dia and connection to pipe etc. all as specified.

S&F Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified.

S&F in repair stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including bedding in cement mortar on to dwarf walls, or including fixing cantilever iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supplying and fixing in replacement of stainless steel plate rack, as in repairs, made out of 0.63 mm thick sheet of size 750x900x250mm (appx.), as per standard pattern and design (approved quality) with plugs, screws, washers etc complete all as directed. Note : Weight of plate rack shall not be less than 8.00 kg each.

S&F Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified.

Disconnecting existing PVC tank exc 500 Ltrs and not exc1000 Ltrs setting aside (or lowering if required) for repairs. Cleaning, etc and hoisting if required reconnecting refixing in position complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified.

S&F in repair 15mm bore chromium plated Bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

Supply and fix in repair for Pillar tap, brass, 15mm dia, with capston heads, chromium plated, fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed.

S&F in repair 15mm bore stop valve/ angle stop cock chromium plated, fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified.

S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified

S&F in repair Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc; complete all as specified.

S&F in repair CP towel rail 450mm long fixed with and including CP brass screws and wooden/ plastic cleats complete all as specified.

S&F in repair CP greating doom 100mm dia complete all as specified.

Supply and fixing 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight for 25mm ball valves-455gms) fixed in repairs i.e., incl taking down and removal of old unserviceable float valves complete all as specified and as directed.

S&F in repair PVC SWR type 'B' socketed rain water pipes 110mm dia conforming to IS: 4985/ IS: 13592 complete all as specified and as directed.

S&F in repair PVC SWR bend/shoe of PVC 110mm dia suitable for 110 mm bore / dia PVC SWR rain water pipes complete all as specified and as directed.

M&L for carrying out treatment for RCC Chajja’s, Ceilling, facia etc; in the following stages :- (i) Dismantling and removing damaged core concrete by manually/ mechanically means in columns, beam, roof slab, chajja, lintels, etc complete including disposal of unserviceable debris. (ii) Diamond wire saw cutting making profile at edges and avoiding feather edges.(iii) Hydro-demolition cutting / cleaning with high-pressure water jetting (iv) Chipping of loose concrete from surface to expose sound concrete beneath using light chisel, hammer & also preparing concrete surface to receive further treatment, disposing the unserviceable debris (v) Sand blasting for cleaning of reinforcement and chipped surface of concrete so as to cause an intense abrading of the reinforcement and removal of rust from entire surface of reinforcement to achieve shining bright surface (vi) Cleaning reinforcement of total rust by tapping or using wire brush or any other suitable way including from behind and around the reinforcement bars to give it a totally rust free finished steel surface (vii) Providing and applying approved chemical rust remover with paint brush on corroded rebar and removing loose particles after 24 hours of its application and washed with sufficient quantity of water to make rebar free from corrosion (Dr. Fixit Rust Remover/equivalent), (viii)Surface preparation to remove all dust, dirt, loose rust scales etc., with wire brush, emery papers, rotary wire bristle brushes and grinding (if required) to the concrete surfaces to receive further repair treatment .(ix) Providing & fixing new reinforcement of various diameters as required at site in the form of mild steel and /or steel confirming to IS and lapping, welding, anchoring suitable to the old reinforcement including cutting, bending with all tools & tackles etc; (x) Providing and fixing GI weld mesh (1” x 1” x 12 gauge) with 30 cm lap at junction, one layer around the cross section of beams/ slab and along the span length. (xi) Providing and applying approved epoxy zinc rich anti-corrosive coating of 40 micron dry film thick/approved thickness of Dr. Fixit Zinc Rich Primer/ equivalent to the exposed reinforcing bars after application of rust remover, on the shear connectors/welded mesh/additional reinforcement of entire concrete repair surface. (xii) Dubbing out PMC 20mm thick (average thickness),(Polymer modified mortar/concrete) on uneven/ irregular surface such as walls / ceiling / chajjas etc. (using 12.5mm graded crushed stone aggregate) including 10mm thick PMM plaster in CM 1:3 ratio (Polymer modified mortar) on concrete surface (when concrete is green) ,(using Polymer modified 20% by weight of cement) complete all as specified and directed by Engr-in-charge.

M&L for Preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cm and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer incharge.

M&L for Preparing new plastered surfaces and applying chalk whitening/ concrete primer as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of Distemper oil Emulsion on new plastered surfaces all as directed by Engr in charge.

M&L for Preparing new plastered surfaces and applying cement based putty concrete primer as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of Distemper oil Emulsion on new plastered surfaces all as directed by Engr in charge.

M&L for Preparing new plastered surfaces and M&L for applying concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of cement base paint on new plastered surfaces all as directed by Engr in charge.

M&L for Preparation of new plastered surfaces of walls etc. & applying three coats of lime white wash on walls complete all as specified.

M&L for Preparation of new plastered surfaces of ceiling etc. & applying three coats of lime white wash on ceiling complete all as specified.

M&L for Preparing old plastered surfaces brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of distempered or painted surfaces and M&L for applying one coat of distemper oil emulsion on old plastered surfaces all as directed by Engr in charge.

M&L for Preparing old surfaces incl brooming surfaces, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil or greasy spots incl washing rubbing down and stopping of distempered and painted surfaces and M&L for applying one coat of cement base paint on walls etc., complete all as specified and as directed.

M&L for Preparation of old decorated plastered surfaces of walls etc. & applying one coat of white wash complete all as specified.

M&L for Preparation of old decorated plastered surfaces of ceiling etc. & applying one coat of white wash on ceiling complete all as specified.

M&L for Surface excavation n.exc 30 cm deep & averaging 15 cm deep getting out in soft/ loose soil complete all as specified and directed.

M&L for Preparing new or previously untreated surfaces of stone/ concrete any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of priming paint plaster coat complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

M&L PCC 1:4:8 type D2 (40 mm graded aggregate) in foundation filling and mass concreteetc complete etc.all as specified and as directed.

M&L for Pre-cast cement concrete block 1:3:6 mix as in masonry with solid blocks, n.exc. 10 cm in width and setting in cement Mortar 1:4 complete all as specified and as directed.

M&L for Form work to sides and soffits of floor or roof RCC beam sides of lintel beam flat fair finish surfaces complete all as specified and as directed.

M&L for Reinforcement 8 to 10mm dia TMT bars cut to length, bent to shape required and binding with MS wire annealed not less than 0.9mm dia in stirrups complete all as specified and as directed.

M&L for providing RCC 1:1-1/2:3 type A1 (using 20mm graded stone aggregate) as in beams, lintel up to 1.5m clear span, lintel bands etc; complete all as specified and as directed.

Returning,filling in,including spreading,levelling,watering and well ramming in layers not exc 25 cm each layer in hard/dense soil all as specified and directed.

Removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point all as specified and directed.

M&L for PCC 1:2:4 type B-1, 25 mm thick using 12.5mm graded stone aggregates as in sub floors/base floors under tiles as in levelling course etc all as specified and directed.

S&F of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of appertuer 1.40 mm fixed fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

S&F butt hinges, medium weight ,stainless steel of 100mm long size and fixed complete all as specified and as directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, 150mm long all as specified and as directed

S&F extruded aluminium alloy handles, 150mm long size, fabricated type, anodised all as specified and as directed.

Supply and fix Bib tap,15mm bore, fancy type, brass chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

Supply and fix Angle valve,15mm bore, fancy type, brass chromium plated, concealed type, with long shank and cup, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

S&F for cast copper alloy chromium plated 2 in 1 Angle Cock Complete all as per sample and all as specified and as directed.

S&F Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe with 15mm pipe all as specified and as directed.

S&F in repair CP greating doom 100mm dia complete all as specified.

S&F Vitreous China wash down water closet pan (Pedestal Pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet with 1.00 to 1.50m long tube (Make of Jet 'Praayag' Cat Part No 5211 or Equivalent) incl making connection to inlet flush pipe, & to 'P' or 'S' drain trap, incl supply of long special 'P' or 'S' trap fixed in repair complete and making good the disturbed portion etc. all as specified and directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks triple layer(cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 gms.) all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head/ handle screwed both ends for 25mm bore iron pipe and fixed all as specified and as directed.

M&L for bedding to drain pipes 150mm dia including packing under, and haunching in PCC 1:3:6 type C2 using 40 mm graded stone aggregate against the side of SWSG after they are laid and tested all as specified and as directed.

M&L for 150 mm bore SWSG drain pipe, of grade 'A' laid in trenches and jointed in CM 1:1, complete all as specified and directed, including testing etc complete all as specified and as directed.

M & L for PCC (1:3:6) type C1 using 20 mm graded stone aggregate as in surfaces channel and drain of man holes finishing surfaces even and smooth complete all as specified and as directed.

S & F 50mm thick Sand stone slabs in Manhole/ drain cover stones etc.n exc. 2m in length,punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4. complete

Cutting into existing manholes, for insertion of 150mm dia of pipe for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching all as directed and specified as directed.

M&L for Formwork for chullah hoods, chajjas through and similar items including edges, surface fair finished complete all as specified and as directed.

M&L for keyed pointing in CM (1:3 ) to Jodhpur type regular coursed masonry complete all as specified and as directed.

M&L for two coats of cement base paint on new pointed/plastered surfaces of walls including preparation of new surfaces over a coat of primer all as specified and as directed.

S&F Pillar tap, brass, 15mm dia, with capston heads, chromium plated, fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin complete all as specified and as directed.

S&F in repair for Vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement , suitable PVC waste pipe with brass unions, including making all connections to existing connections,complete all as specified and as directed.

M&L for Jodhpur stone patti slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, laid dry as in manhole coveres, sizes as directed by Engineer incharge complete all as specified and as directed.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

M & L for concealed point wiring One light / bell / buzzer / fan / exhaust fan point controlled by one no, 1-way, 5 Amps switch complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed FRLS cable 1100 volt grade, confirming IS 694 & proper colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls / floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, all as specified, directed and shown on drgs for The rates of chase cutting on wall done concealed conduit and steel terminal boxes are included in the unit rates all as specified and directed by Engr-in-Charge.

All as per srl item no 175 here-in-before but for One light point controlled by two nos, 2-way, 5 Amps switch.

All as per srl item no 175 here-in-before but for One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per srl item no 175 here-in-before but for One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per srl item no 175 here-in-before but forwith 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for indpendent 15 Amp point.

S&F of Switch piano type, single pole, one way, 5 amps, 230 volts, complete all as specified and directed. Make : Havells (Rio) / Gold Medal / SSK

S&F of Switch piano type, single pole, two way, 5 amps, 230 volts, complete all as specified and directed. Make : Havells (Reo) / Gold Medal / SSK

S&F of Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed. Make : Havells (Reo) / Gold Medal / SSK

S&F of Switch piano type, single pole, one way, 15 amps, 230 volts, complete all as specified and directed. Make : Havells (Reo) / Gold Medal / SSK

S&F of Socket, 6 pin, 5/15 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed. Make : Havells (Reo) / Gold Medal / SSK

S&F of Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed. Make : Havells (Reo) / GM / SSK

S&F LED lamp 7W complete all as specified and directed by the Engineer-in-Charge. Make : Havells / Wipro / Crompton

S&F of wall mounting light fitting City 2 and incl suitable size 9W retrofit LED bulb and making necessary electric connection, complete all as specified and directed. Make : Havells City 2 / Philips / Crompton

S&F of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed. Make : Havells (Rio) / Gold Medal / SSK

S&F of Bell push, flush type 5 amps, 230 volts. Make : Cona / Havells (Reo)/ Gold Medal

S&F of electric call bell ding dong AC 230 volts Single Pole. Make : Gold Medal / Havells / Cona

S&F of resistance type regulator A/C 240 Volts. Make : Cona / Havells (Rio)/ SSK

S&F of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single MCB SP 20 Amps. Make : Legrand / ABB / L&T

Fixing only of LED light fitting 1 X 20/22 watt (4 feet) and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed.

Fixing only of LED light fitting 1 X 10 watt (2 feet) and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed.

S&F of bldg security LED Light Luminaire of 45 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with fixing of GI pipe 40 mm bracket appx 1.50 m long bend to shape as directed including drilling holes nuts & bolts 2 coats of red oxide paint on GI pipe and fixing with wall security light on building wall complete all as specified and directed. Make : Philips / Crompton / Wipro

S&F of plastic ventilating fan 200 mm sweep plastic body including louvers with cutting chases on brick wall and grounting with nut bolts on aluminium frame complete all as specified and directed. Make : Crompton / Havells / Orient

S&F of Vertical Distribution Board, double Door, suitable for 'A' Frame FP MCCB 100A made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 4 way, 415 volts with bus bar rating 300 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Make : Havells Cat Part No DHDLVSRWGOFO04 / Schneider Elect / Legrand / ABB Note : MCCB & MCB will be measured and paid separately under respective items

S&F of Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 08 way (Concealed flush to wall), 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Make : Havells / Schneider Elect / Legrand / C&S / Hager

S&F of MCB, C Curve type, 10 kA, 63Amp, SPN with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Havells

S&F of MCB, C Curve type, 10 kA, 40Amp, SPN with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F of MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager

Taking out old worn out wooden frame / steel frame and supply & fixing of single door sheet metal borad complete with flush door handle with locking arrangement painted with powder coated finishing with necessary PCC work complete size 1000x1000x300 Make : BCH Cat Part No BIL 50540 or Equivalent make in Havells/Hagger

All as per srl item no. 202 here-in-before but size 800x800x300 Make : BCH Cat Part No BIL 50310 or Equivalent make in Havells/Hagger

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15/20 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two run of 6 Sqmm wire and one run of 4 Sqmm wire will be measured as one unit. 3. Make of Wire : Standard / KEI / C&S / RR Kabel

All as per srl item no. 204 here-in-before but with 2 run of 4.0 sq mm FRLS copper wire with 4.0 Sqmm FRLS copper cable as earth wire.

All as per srl item no. 204 here-in-before but with 2 run of 4.0 sq mm FRLS copper wire with 4.0 Sqmm FRLS copper cable as earth wire including casing capping complete with all accessories.

All as per srl item no. 204 here-in-before but with 2 run of 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper cable as earth wire including casing capping complete with all accessories.

Supply, laying, testing and commissioning of LT UG cable, XLPE insulated, PVC sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 16 sqmm 4.0 core confirming to IS:7098 (Part-I), suitable for earthed system, laid in duct/trench/along pole/wall etc including nuts, bolts, washers, saddles & screws etc and making connection from LT over head line to DB, complete all as directed. Make : Finolex / KEI / Polycab Note : 1. The cost of Al thimbles/lugs and cable gland etc is included in quoted rate and no extra payment will be made for it. 2. Excavation, earth work, sand cushioning and brick protection will be measured and paid separately under respective items.

Excavation in trenches in hard / dense soil not exceeding 1.5 meter depth and not exceeding 1.5 meter wide and getting out including trimming of sides, complete all as directed.

Supply and laying 40 to 50 mm thick roughly hammer dressed Jodhpur stone slab cover 25 to 30 cm wide and not less than 60cm long dry laid, abutting each other gap between adjacent slabs not exceeding 10mm for protection of underground cable complete all as specified

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 10cm after laying of cable in trenches complete all as directed and sand cover to under ground cable complete all as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick, complete all as specified

Removing excavated material to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point, complete all as specified.

S&F of GI pipe of 50 mm nominal dia light grade fixed to poles with clamps nuts, bolts and washers or laid under road crossing or fixed to wall including painting with two coats of aluminium paint over a coat of red oxide paint complete all as directed. Note : The cost of MS clamp, nut, bolt, washer and GI fittings etc shall be inclusive in the item rate.

Taking down carefully of old Ceiling Fan / Electric Meter and Exhaust fan, keep in safe custody and refix the same after completion of consturction work with all accessories, making necessary electric connection from ceiling rose / Main DB to fitting terminal, complete all as specified and directed

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.

M/L Point wiring for One fan point controlled by one 5 Amps switch complete with 1.5 sqmm single core PVC insulated and PVC unsheathed FRLS multistranded copper conductor cable 1100 volt grade enclosed in and including PVC casing and capping with accessories fixed on surface on walls/ceiling by means of PVC sleeves Dash-fastners and cadmium plated screws all as per ISI including sunk type boxes for mounting fitting like switches, socketes fan regulators with 3 mm thick phenlic laminated sheet top covers concealed in walls etc including 1.5 Sqmm single core multi stranded copper conductor PVC insulated and unsheathed cable as earth continuity conductor to common earth dolly.

Ditto but for One independent socket point controlled by one 5 Amps switch ditto-

Fixing only of ceiling fan 1200 mm sweep, alongwith fan regulator incl down rods and connecting up with 3 runs of 1.5 Sqmm, single core PVC insulated but unsheathed, FRLS cable with multi stranded copper conductors IS 694 marked, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed.

Fixing only heavy duty Exhaust fan 300 mm sweep, 900 RPM, including louvers with cutting chases on brick wall and grounting with nut bolts connecting up with 3 runs of 1.5 Sqmm, single core PVC insulated but unsheathed, FRLS cable with multi stranded copper conductors IS 694 marked, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed.

M&L Opening of wall and making good disturb surface as per existing surface complete all as specified and directed.

Fixing only Water cooler electric driven (single phase), having approx storage capacity of 80 litre and nominal cooling capacity of 40 Litres per hour, including staging, necessary pipe and electric connection and all connected works, complete all as specified and directed by Engineer-in-Charge.

Fixing only 2 KVA Voltage stabilizer for Water cooler with output voltage stabilized at 230 V with accuracy of ± 2.5% and making necessary electric connection thorugh stablizer to fitting terminal, complete all as specified and directed.

Fixing only of storage type electric Water heater (Geyser), including fastner nut and bolts, and making necessary electric & pipe line connection, complete all as specified and directed by Engr-in-Charge.

S&F 15mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed by Engr-in-Charge. Make : Leader /Zenith / Zoloto

S&F flexi PVC connection pipe of size 15mm dia with brass nut 2 Nos suitable for Hot water connection of geysers, complete all as specified and directed by Engr-in-Charge. Make : Prayag or equivalent ISI Marked

Fixing only Desert cooler electric driven single phase, fixing of float valve, inter-connect with water pipeline and necessary electric connection complete all as specified and directed by Engr-in-Charge.

S&F Cooler stand 1.2x1.0 mtr in rectangle shape of hallow MS pipe including applying two coats of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge

S&F PVC float valve with PVC floats 15mm dia pipe suitable for desert cooler complete.Make : Prayag or equivalent ISI Marked

Supply & Installation, testing & commissioning of galvanised steel sheet (G.S.S) square / rectangular ducting made out of 24 guage galvanised sheet class VIII fabricated from galvanised steel sheet of the following thickness having zinc coating of 160gm / Sqm total on both sides complete with gaskets, elbows, splitters, valves etc., as per IS 655/1963 (Revised upto Date) all as specified and including with required scaffolding work to install the duct at site :-

Supply & Installation, testing & commissioning of galvanised steel sheet (G.S.S) square / rectangular ducting made out of 22 guage galvanised sheet class VIII fabricated from galvanised steel sheet of the following thickness having zinc coating of 160gm / Sqm total on both sides complete with gaskets, elbows, splitters, valves etc., as per IS 655/1963 (Revised upto Date) all as specified and including with required scaffolding work to install the duct at site :-

S&F in replacement of MCCB, A Frame, thermal adjustable magnectic setting, Ics = 75% 25 kA, 415V, 100 Amp, 4 Pole MCCB with over load and short circuit protection, complete all as directed. Make : Havells Cat part NoIHLASF0100 # / Schneider Elect / Legrand / ABB

Supply & fixing Fresh Air Damper of size 450mm x 300mm made out of Galvanised steel sheet cutting / opening in wall on fixing in aluminium frame of existing window all as directed by Engineer-in-Charge.

Supply & fixing Ultra Violet Tube Lights of 2' on wall / in duct & near cooling coil of AHU unit. DVC 254nm all as directed by Engineer-in-Charge. Make : Philips / Crompton / Havells

M&L for Jodhpur stone slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, laid dry as in manhole covers, sizes as directed by Engineer in charge complete all as specified .

AB Constructions

Panwar Electricals

M/S Dharam Chand Lal Chand Jain

M/S KAUTILYA GARG

KARNI CONSTRUCTION COMPANY

M/S gayatri construction company

Bhagwati Construction Company

Pawan Kumar Shrama Contractor