SPL REPAIR TO BLDG NO P 205 AND SIX TOILET BLOCK OF BLDG NOS T 64 T 58 T 57 AND P 200 AND PROVN OF ATT TOILET AND SENTRY POST AT MIL STN DHRANGADHRA

Amount

Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation of pole,laying of cables etc in hard and dense soil and getting out complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation (50 mm thick sand cushioning).

Removing excvaated soil nexc 50m and depositing where directed at a level n exc 1.5 m above the stating point soil etc completed all as specified and as directed.

Removing excavated material to a distance exc. 1.50 km but n exc. 5 km from the starting point etc complete all as directed

M&L, Hardcore of broken stone of gauge n exc 63mm deposited, spreaded & levelled in layers n exc 15cm thick including watering and ramming etc complete.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n. exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation, sub base, filling and mass concrete complete all as specified and directed

M&L for cement concrete 1:3:6, type C1 using 20mm graded stone aggregate as in coping, including necessary formwork etc complete.

Providing, cement concrete type B0 1:2:4 (12.5mm graded aggregate) in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed.

M&L for pre cast cement concrete block masonry with solid block exc 10 cm in width type B1 (1:2:4) using 20mm graded stone aggregates and settting in CM 1:6 complete al as specified and directed.

M&L for providing precast cement conctete 1:2:4, type B1 using 20mm graded stone aggregate as in piers caps post boundary pillars blocks etc setting 1:4 all as specified and directed.

M & L for reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Reinforcement cement concrte B-1 1:2:4 (using 20 mm graded granite stone aggregate) as in coping, Beams, cantilevers, bressummers, lintels over 1.5m span. Set in CM 1:6 complete all as specified and directed.

Supply only, integral water proofing compound.

Cutting holes into or through stone walls built in cement mortar or cement lime mortar and walls of cement concrete having superficial area exc 150 sq.cm but n exc 400 sq.cm complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) completed as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm for sand stone and dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses completed as specified and directed.

M&L Granite or trap Stone kerb of roughly squared stones of size 20cm x 30cm, all surfaces hammer dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 20mm jointed in cement mortar 1:6 and struck flush

Rough finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

Rough finished flat Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

Taking down chowkats or frame of any description n exc 1.5 Sqm each (without taking off shutters from the frames) complete as specified and directed.

Taking down chowkats or frame of any descrip tion exc 1.5 Sqm each and n.exc 4 Sqm (without taking off shutters from the frames) complete as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications and drawings complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed by Eng-in-Charge.

S&F aluminium, anodised barrel tower bolt of extruded section and fixed 200 mm of size

S&F, 250mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 150mm size, aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

Taking down chowkats or frame of steel window/ ventilator n exc 1.5 Sqm each (without taking off shutters from the frames) complete as specified and directed.

S&F, in repairs mortice lock of mild steel, vertical type of size 75mm with duplicate key for door complete all as specified.

S&F, in repairs, brass chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F, in repairs, Door closer hydraulically regulated of aluminium (extruded section) body, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

S&F,in repairs, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

S&F MS framed work such as grills, guard bars of window and similar work with ends of bars shouldered and/ or riveted, or forged into spikes conforming to Fe 290(Gde E-165) complete all as specified and directed.

S&F mild steel bolts,purpose made,with hexagonal or square head one end and screwed the other,or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long dia of neck in exc 12 n.exc 20mm complete all as specified and directed.

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inclding cranking, bendiing spirally for hooping for columns, hooking ends and biinding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F Mild steel for roof trusses (framed), trussed purlins, crane gantires, rails and fasternings and heavy bracket framming (beam, tee, angle, channel or flat sections ) incuding distance pieces, clats etc. and confirm to Gde- Fe-410-0 or Fe 310-0 including one shop coat of zinc chrome primer complete all as specified and directed.

S&F factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

M&L for anodised aluminium frame/shutters for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to walls, fixed with self tapping screws as specified.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

M&L for rounding to edges of stone slabs two edge full round,such as in steps,cooking platform and other similar situation complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L 75 mm thick cement concrete type D2, 1:4:8 (40mm graded aggregate) in sub-floors, sub-bases, floors and pavings etc complete all as specified and directed.

M&L for 25mm thick cement concrete type B1, 1:2:4 (20mm graded stone aggregate) to receive floor finishes complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors and fixing of glass dividing strips, finishing the surface even and smooth with using extra cement complete all as specified and directed. Note -Glass dividing strips paid separately.

M&L for Glass dividing strips, 3 mm thick, Width of strip 38mm and inserted in position, conform to design complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size350x250x7mm/450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but including 600 x 600mm size in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but including 600 x 600mm size as in dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:6 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces on fair faces of brick/Stone work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (plaster shall be done in two coats. 1st coat shall be 10 mm thick in CM (1:6) and 2nd coat shall be 5mm thick in CM (1:4) mixed with water proofing compound) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed. (Note :- Water proofing compound shall be measured and paid separately )

M&L for rendering 15mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 20mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in (1:4) cm on fair faces of ceiling, chajjas, fins facia etc finished even and smooth without using extra cement complete all as specified

M&L for preparing new plastered or un-plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed.

M&L for preparation of new surfaces of plastered or unplastered of wall and application of three coat of white washing.

M&L for preparing old plastered or un-plastered walls surfaces and applying one coats of white wash on walls complete all as specified and directed.

Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc.

M&L for preparing of new plastered or un-plastered surfaces and applying two coats of oil bound distemper over a coat of primer over and including wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

S&F, in repairs, false ceiling at any height, 600x600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH-99 classic lite' with suspension system complete all as specified as per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

S&F, in repairs, 20mm dia,stainless steel, fancy type, tubular curtain rod fix on decorative brackets with decorative globe at both ends complete all as specified and directed.

S&F Glazing with sheet, 3mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane.

S&F 4mm thick Sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane

M&L for 3mm thick figured glass, pin headed type and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) not exc 0.5 sq.m from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

M&L for preparation of old steel surface of any description exc. 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L Adequate No. of coats painting to kerb stone of pavements and the like exc 10cm wide with road marking paint, white or golden yellow complete all as specified and directed.

S&F, in repair, vitreous china table top wash basin, white, flat back of size 550mm x 400mm including grouted in cement mortar 1:2 on Granite top supported on RCC slab complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately. Make : Cera (Brand Coyal/Corba/canal) or equivalent as approved by Engr-in-Charge.

Supply only Pillar cock 310mm long extended body cast copper alloy with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore Make : Cera (Cat part No F1014102) or equivalent as approved by Engr-in-Charge.

S&F in repairs 32mm waste fittings brass chromi-um plated for glazed ware basin etc with long screwed shanks and fly nuts flange end complete ISI marked complete all as specified and directed.

S&F, Bib taps,15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F, in repairs, 15mm brass chromium plated fancy type bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F, in repairs, 15mm stop valves, fancy type brass chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed.

Supply only, pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

Supply only 15mm pillar taps, brass chromium plated fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe or for union and fixed to 15mm bore pipe, complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 25mm bore of pipe complete all as specified and directed.

S&F, rotational moulded polyethylene water storage tanks of capacity 500 Litres (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I including 20mm dia PTMT ball valve complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of capacity 500 Litres (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I including disconnecting and removal of old U/S PVC tank complete all as specified and directed.

S&F in repairs 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) all as specified and directed

S&F, in repairs, 8mm dia brass chromium plated health faucet(Hand shower) with 01 metre long flexible tube and wall hook complete all as specified. Make : Jaquar Cat No. ALD-573 or equivalent as approved by GE.

S&F,in repairs, chromium plated over head shower 100mm dia round shape single flow (ABS Body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed as per Cat No EOS-542N of Essco or equivalent make approved by GE.

S&F 32mm bore, low density polyethelene pipe(LDPE) of pressure rating 6Kgf/Sqcm fixed to wall, ceilings or in floors etc complete all as specified and directed.

S&F, 40mm bore high density polythene pipes (HDPE) of pressure rating 6 Kg/cm2 fixed complete all as specified and directed.

S&F, in repairs, grating square 150mm size of PTMT (minimum weight 100 gms) complete all as specified and directed.

S&F, Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minium weight 190 gms) complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/ walls

S&F 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/walls

S&F PVC (SWR) bends of any radius with oval and access door of 75mm dia

S&F PVC (SWR) bends of any radius with oval and access door of 110mm dia

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal suitable for 110mm bore pipe.

S&F PVC (SWR) vent cowl of 75mm dia

S&F PVC (SWR) vent cowl of 110mm dia

S&F PVC (SWR) Floor/ Nahani trap with grating of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4).

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete fixed all as specified.

M&L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 200 mm bore.

M&L for Salt Glazed stone ware drain pipes, 200 mm internal dia Grade 'A' laid in trenches and jointed complete all as specified and directed.

S&F, in repair, vitreous china wash down water closet pan (wall hanging two piece pattern) including 'P' or "S" trap, and seat cover with complete fitting. Make : Cera (Brand Compell/Celiver) or equivalent as approved by Engr-in-Charge.

Cutting into existing manhole 200 dia for connection new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate, smooth finished and reforming benching as required all as directed.

S&F in repairs, Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc including seat cover etc. complete all as specified and directed.

S&F, in repairs, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repairs, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, in repairs, Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.

S&F, 32mm High density polyethylene pipes (HDPE) of pressure rating 6 kgf/sq/m as in waste pipe for urinal etc. complete all as specified and directed.

S&F, PVC flushing cistern low/high level including brackets ball valve, float etc complete capacity of 10 letres complete all as specified and directed.

S&F, vitreous china wash hand basin, white flat back of size 550x400mm excluding taps but including CI brackets, 40mm CP waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and directed.

S & F in repairs white glazed earthen ware vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste coupling Inlet/ outlet, PVC flexible pipe, 600mm size for 15 mm bore pipe with brass nut and washers etc complete.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles.

Dismantling stone slab and tiles of any description or thickness in floors,aprons etc.

Dismantling of asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes jointed in neat cement mortar and taking out of trenches if required.

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :- Make of Cable Polycab/Finolex/Havells

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(c) One multi pin 5 Amps, socket outlet on Independent board.

M&L for concealed type point wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including rigid PVC conduits ,20/25 mm ISI marked with valied CML number including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed. Make of Cable Polycab/Finolex/Havells

S&F, lamp holder insulated body with back plate for battern fittings complete all as specified and directed.

S&F, in repair, switch piano, flush button single pole, one way 5 Amps complete all as specified and directed.

S&F, switch piano, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F , modular switch 1 way 10A, 1 module complete all as specified and directed. Make of Anchor(Roma) or equivalent make Legrand/ Havell /ABB.

S&F, Ceiling rose, PVC/poly carbonate,isolated body three terminals,complete all as specified and directed.

M&L in replacement sub-main wiring with 2 single core 4 Sqmm PVC insulated, unsheathed, 1100Volts grade, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit assessories including drawing a run of PVC insulated, unsheathed, 650/1100Volts grade, copper conductor multi stranded 4 Sqmm size as continuous earth wire drawn through and connected to main switch/ DB and testing on completion. Note: (i). 2 run of main conductor and one run of earth conductor shall be measured as one length. (ii) Rates quoted shall be inclusive of cutting wall for concealing conduit and making good the same in cement mortar 1:3.

S&F, socket outlet, 2 in 1, 3 pin, 15 Amps and 5 Amps flush type complete all as specified and directed

S&F, in repair, socket outlet 2 in1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F, miniature circuit breakers, type curve ‘B’ , 10 KA, SP, 6 to 32 Amps complete all as specified and directed.

S&F, in repairs, miniature circuit breakers, Single pole and neutral, type curve ‘B’ 10KA, 32 Amps 230 Volts. complete all as specified and directed.

S&F, miniature circuit breakers, Single pole and neutral, type curve ‘C’ 10KA, 40 Amps 230 Volts. complete all as specified and directed.

Excavation in trenches in soft / loose soil n . exc 1.5 mtrs wide and not exceeding 1.5 mtrs depth for taking out / laying of under ground cables and getting out all excavated materials with bricks bats etc as directed .

Returning, filling in, trenches with soft/ loose soil including spreading levelling watering and well ramming in layers not exc 25 cm with excavated soil complete all as directed.

Removing surplus spoil to a distance not exc 50 mtr away and depositing where directed at a level n.exc. 1.5 mtr above the starting point complete all as specified.

M&L for Sand coarse filling in trenches obtained from local river for cushioning of UG cable all as specified and directed .

Supply and laying well burnt best quality locally available bricks of size 25X12.5X7.5 cm (+/-) 8% tolerance laid flat for protection of UG cable all as directed .

M&L tubing GI tubing light grade laying for protection of LT under ground cable of size 40 mm bore. Make: Jindal/ Tata/ Bansal.

S&F, in repairs, LED light fitting, batten type, housed in extruded from powder coated aluminium, 18 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed. Make of Cable Polycab/Finolex/Havells

S&F, in repairs, bell, A.C. 230 Volts, single pole, Ding doll, complete all as specified and directed.

S&F , in repairs, modular socket 10 Amps, 2/3 pin combined, 2 module complete all as specified and directed. Make of Anchor(Roma) or equivalent make of Havells/ legrand.

S&F, modular switch 1 way 20A, 1 module complete all as specified and directed. As per Cat No. 21066 of Anchor(Roma) or equivalent make Legrand/ Havell /ABB.

S&F, in repairs, modular socket 20A, 2/3 pin combined, 2 module complete all as specified and directed.Make of Anchor(Roma) or equivalent make of Legrand/ Havells.

S&F, in repairs, modular bell push 6 Amps, 1 module complete all as specified and directed. Make of Anchor(Roma) or equivalent make of Legrand/ Havells.

S&F, in repairs, modular fan step type regulator, sutabule for 1200/ 1400mm sweep, 1 module complete all as specified and directed. Make of Anchor(Roma) or equivalent make of Havells.

S&F , modular white cover plate with frame for 1/2 modules complete all as specified and directed

S&F, modular white cover plate with frame for 3 modules complete all as specified and directed

S&F, modular white cover plate with frame for 4 modules complete all as specified and directed

S&F, modular white cover plate with frame for 6 modules complete all as specified and directed

S&F, modular white cover plate with frame for 8 modules complete all as specified and directed

S&F, modular metal flush box concealed type with 1/2 module for housing modular switches complete all as specified and directed

S&F, modular metal flush box concealed type with 3 module for housing modular switches complete all as specified and directed

S&F, modular metal flush box concealed type with 4 module for housing modular switches complete all as specified and directed

S&F, modular metal flush box concealed type with 6 module for housing modular switches complete all as specified and directed

S&F, modular metal flush box concealed type with 8 module for housing modular switches complete all as specified and directed

Taking down the existing ceiling fans complete with down rods and refixing the same with supply of new down rod of size 15 mm dia made of GI pipe med grade aprox 1 metre length incl flexible wire all as specified and directed.

Supply, laying, connecting and testing of LT under ground electric cable 10 sqmm, 2 core,XLPE insulated armoured heavy duty with stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape 1100 Volts grade , laid in trenches or drawn through GI pipe or fixed to wall with providing suitable size of metal clamps, cable glands, aluminium lugs, GI nuts bolts and washers complete wherever required complete all as specified and as directed . ( Make : Havells / Finolex/ Polycab)

S&F, in repairs, sheet metal enclosures, single pole & neutral with a two pin & earth plug and socket complete with one single pole, MCB of 20 Amps, 10 KA, 240 volts complete all as specified and directed. Make ;Legrand / Havells/ standard.

S&F, in repairs, sheet metal distribution board, SPN, 8 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed

S&F, in repairs, sheet metal distribution board, SPN, 12 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A bus bar complete all as specified and directed. Make ;Legrand / Havells/ standard.

M&L for GI water tubing, medium grade laid in trenches/on wall etc with running fitting complete for 20mm dia of pipe ISI marked complete all as sepcified and directed.

M&L for GI water tubing, medium grade laid in trenches/on wall etc with running fitting complete for 25mm dia of pipe ISI marked complete all as sepcified and directed.

S&F gun metal gate valve with iron wheel head, both ends screwed of 25mm bore of pipe compelte all as sepcified and directed.

M&L for construction of brick masonary valve pits of size 600x600x600mm (internal dimension) with brick work in cement mortar (1:4) including excavation and earth work, Concrete work, 3mm thick MS sheet cover with locking arrangement, hinges and handle incl angle iron frame ,rendering work, painting to all steel surfaces with two coats of black bituminous paint over a coat of red oxide primer complete and including demolition of existing damaged valve pit .

M&L for cutting of existing CI/GI Pipe line for taking branch connecting by necessary cutting/welding work,providing GI fittings such as tee/reducers etc upto 100 mm bore complete including necessary earth work complete all as directed at site.

S&F, in repairs, LED light fitting, batten type, housed in extruded from powder coated aluminium, 18 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed. Make: As per Cat No. BAJAJ LED BATTEN 18W of Bajaj or equivalent make : Havell / wipro/ philips.

S&F, in repairs, LED Mirror light fitting, housed in extruded from powder coated aluminium, 10 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

S&F, Exhaust fan 250mm sweep, AC 50 Hz, 240 V PVC Body Complete with blade alongwith louvers all as specified and directed.

S&F of Wall mounting fan 400 mm Sweep ,AC 50 Hz 240 V Complete with 3 blade all as spcified and directed Make : BAJAJ / HAVEELS /USHA

Supply and installed Water Heater storage type 25 ltr capacity complete with all necessary items,AC 50 Hz 240 V Complete with all as spcified and directed Make : BAJAJ / HAVEELS /USHA

M&L for cutting holes into or through concrete/stone masonry walls built in cement mortar or superficial area exec 400 sq.cm but n.exc 0.10 sq.cm to a depth of 30cm including provision of suitable bolts, nuts, washers and grouting on walls and making good the disturbed surfaces to match with the existing surfaces including making good and rubbish off the premisses providing Nut bolt for fixing of Exhaust fan complete all as specified and directed.

S & F LED 24 watt recess mounting 2 x 2 luminaire of 24 watt, white powder coated CRCA housing with highpower LEDs. Aluminium front frame with flat white high transmission acrylic cover prewired and all accessories complete all as specified and directed.

S&F in replacement of building security light luminaries 25 watt with wall mounting bracket of suitable size and clamps, nut bolts etc.having pressure die cast housing with epoxy power coated dark graphite grey colour finish,prismatic polycarbonate cover with individual LED lenses-IP65 prewired Conforming to Crompton or of equivalent make of wipro/Havells/Philips wipro

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth Lead 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth strip of 25x4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 40 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 40 mm bore light grade 7.5m.

Bhumi Construction

Shree Builders

BHAVIK SUPPLY CORPORATION

AMI CONSTRUCTIONS