SITC of Pumping Machinery along with accessories with 5 year free comprehensive maintenance Guarantee Period at Mudetha GIDC Industrial Estate.

Name Of Work: SITC of Pumping Machinery along with accessories with 5 year

free comprehensive maintenanace Guarantee Period @ Mudetha Industrial

Sr. Item Description Qty Unit Rate/Unit Amount

No. Excl. GST Excl.

(Rs.) GST (Rs.)

PART - I- FOR BORE WELL.

1 Supplying submersible pump set for bore of 250mm/300 2.0 Set 117502.39

mm. dia having 3 phase motor capacity about 60 H.P

/80 H.P discharge capacity having below working at

Phase 400/440 volt 50 c/s AC Supply & 2900 R.P.M.

a) Capacity: 100 to 400 LPM.

b) Head range : 182 to 265 mtrs

c) Dupty point : 250 mtrs

d) The pump shall have best efficiency at duty point &

Suitable to 100 mm Delivery pipe e) Pump should have

Minimum number of Stage and It should be Suitable for

bore dia 300 mm Ø.

f) Supply 3 phase. 415 V, 50 Hz AC power

g) Method of starting :ATS

h) The guaranteed minimum overall efficiency of pump

shall be as per the ANNEXTURE– ‘B’ attached herewith.

The pump having overall efficiency less than the

specified in ANNEXTURE-B shall not be accepted.

2 Projviding and Erecting ISI marked PVC insulated PVC 350.0 Rmt. 993.84

sheathed Flat flexible submersible copper cable. (J)

Core X 35 sq.mm

3 Supplying and erecting approved make3 phase motor 2.0 No 87191.28

control panel (ATS) made from 16 G. CRCA sheet duly

painted with epoxy power paint inside and outside with

hinged doors and locking arrangement, consisting, of

suitable switch of AC 23 duty with HRC fuses (Cat.III),

starting and running contactors, overload relay,

Automatic water level controller, Electronic timer with

master timer CT operated Ammeter with selector

switch, Voltmeter with selector switch, phase indicating

lamps, single phasing preventer , water level guard, over

load, start, run and stop push buttons, air cooled auto

transformer with 60%, 70%, 80% tapping with required

protection relays and control accessories. Panel to be

erected on angle iron frame grouted on wall as

directed., contactors relays, timer etc. shall be of L & T

Siemens / Cutler Hammer make. Suitable to above

Pump-Motor Set. ATS from 91 to 100 HP.

4 Providing & erecting approved make Four pole moulded 2.0 No 20946.39

case circuit breaker having breaking capacity/strength

ICU of 35 K.A. at 415V. having normal current rating up

to 250A. with variable thermal & magnetic release

suitable to work on A.C.supply 50 c/s. with all internal

connections & complete erected on polished wooden

board/ in existing 16 G.M.S housing.ICS = 100% of ICU

5 Supply of 100 mm diameter of HEAVY UPVC column 240.0 Rmt. 1130.19

pipe with coupler and wire locks in approximate length

of 3.00 mtrs,35 kg /cm^2 waight.

6 Supply of SS TOP & BOTTOM accessories with pump 2.0 Set 3872.34

guard set suitable to item no.5 as directed by Engineer -

in - charge with necessary plumbing as desired.

7 Supplying & erecting G.l. bend for pipe connections 8.0 No 548.43

suitable for 100 mm dia column pipe. (04 nos for bore

well + 04 nos for UG sump)

8 Supplying & erecting ISI Marked 100 mm dia G.l. Union 2.0 No 486.82

for pipe connections suitable for 100 mm dia column

9 Providing and erecting ISI mark CI Double Flanged 100 5.0 No 4077.37

mm sluice valve as per IS :14846 including all

taxes,insurance ,transportation ,freight, charges

,octroi,inspetion charges ,loading,un

loading,conveyance to departmental stores ,staking

etc.complete with ISI mark only . P.N,1.6 With hand

wheel /cap operated (PD type Short Body) (2 no for Bore

well+2no for UG sump)

10 Providing and erecting ISI mark 100 mm C.I Non Return 3.0 No 6062.02

valve including all taxes,insurance ,transportation

,freight, charges ,octroi,inspetion charges ,loading,un

loading,conveyance to departmental stores ,staking

etc.complete with ISI mark only , IS 5312 ,PN-1.6 (1 no

for Bore well+2no for UG sump)

11 Supply of errection clamps with nut & bolts Clamp made 4.0 Pair 282.80

from M.S. plate with 3 holes on either side with nuts &

bolts of std. Make and suitable size 4"(Width)x

1.5"(Thickness)x 24" length flate suitable to 100 mm dia

column pipe & 300 mm dia Borewell. (2 pair for bore

well+ 2 pair for UG sump)

12 Supply of all flanged, heavy duty CI Tee as per IS 1538/ 2.0 No 1523.08

1986 specification suitable for use with C.I. column pipe

of 100 mm dia. size of C.I. Tee- 100 x 100 x 100 mm dia

Supply of M.S. Blind blank flange having 15 mm

thickness. With standard holes for 12.5 mm dia bolts. (1

nos for bore well + 1 nos for sump)

13 Supplying & erecting in earthpit of minimum bore dia. 2.0 No 5842.85

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to

submit test certificate including value of earth resistane

of installation. (A).For electrical installation up to 440 V

length of pipe 1 Mtr back filling compound -1 Nos of bag

of 15 kgs. (1 no for bore well + 1 nos for sump with pump

14 Lowering of submersible motor pump set complete with 1.0 Job 2996.67

required. Nos. and size of casing pipes erected by means

of proper chain pulley block & pipe wrenches after

checking of threads of each pipe with coupling to take

the load of the pump set and pipe assembly filled up

with water. Above 120 mtr & up to the depth as directed

by Engineer-In-Charge

15 Design, Supply, Installation, Testing, Commissioning of 1.0 No 66495.37

Full Bore 100 mm dia Electromagnetic flow meter with

factory calibrated, Regular Power Operated, flanged

connection, Flow sensor, Indicator, transmitter and

totaliser with all accessories viz. (I) Flow Meter/ Sensor:

DC pulsed type, IP 68 Protection, Flanged process

connection as per IS 1538 or equivalent standard,

SS304/ Metallic Alloy Flow Tube, SS316/ SS 316 L/

Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/

Inbuilt Grounding Electrode, Neoprene/ Polyurethane/

Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/

Carbon steel with Anticorrosive Paint Coil Housing with

Junction Box, CS flanges.(II) Flow Transmitter/ Converter

( Remote Field Mounted):Microprocessor based,

Modular design, 2 line LCD for indication of actual flow

rate, forward, reverse, sum totaliser display, ±0.5%

accuracy at 0.3 to 4 m/sec velocity, 4 to 20 mA with

HART/Modbus output, one scalable pulse, one status

output, IP 67 protection, Die cast aluminium/

polycarbonate/ SS316 with Anticorrosive Paint/ PU

finish with glass window enclosure, Inbuilt EEPROM and

Data Logger, 20 meters cable length for sensor to

transmitter communication etc alongwith wall

mounted/ stand ounted cabinet.

16 Design, Supply, Installation, Testing, Commissioning of 3.0 No 1039.29

Bourdon TypePressure Gauge, ±1% accuracy, Direct

bottom 1/2" NPT (M) process connection, IP

Glycerine filled, SS304 Case with Bayonet Type Bezel,

SS316 L Bourdon Tube, SS 316 Movement material,

Aluminium dial with black graduation on white

background, Micro Zero adjustable pointer, neoprene

gasket, Blow out disc, shatter proof glass, SS tag plate

etc as per IS 3624. 100 mm Dial Size (0 to 21 Kg/cm2)

PART - II- PMC FOR UNDER GROUND SUMP.

17 Providing & erecting open well horizontal mono block 2.0 No 35026.80

pump set having 3 Phase 400/440 Volt,50 C/S,A.C Supply

& 2800 RPM following IS 9079 at departmental stores

with following MOC: Casing:CI-FG260,Impeller:Bronze &

Shaft:SS:410 having 500 to 900 in LPM @ 15 to 30 mtr

Mtr head suitable for 100 mm dia delivery pipe

i) Discharge capacity range = 500 LPM to 900 LPM (1

Working + 1 Standby)

ii) head range = 15 to 30 Mtrs.

Duty point =20 mtr

iii) Impellers : SS(Stainless Steel)-410

iv) Delivery size : 100/150 mm dia.

18 Providing and erecting ISI marked PVC insulated PVC 60.0 Mtr 146.45

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (C) 3 Core x 4 Sq. mm

19 Supplying & erecting approved make motor control 2.0 Set 15818.62

cubical panel (STAR-DELTA) made from 16 G. CRCA sheet

duly epoxy powder painted inside and outside with

hinged doors and locking, arrangement consisting of

suitable size of ON- OFF isolator (AC - 3/23duty) main

fuses, single phasing preventer, indicating lamps for R- Y

- B phases, overload relay, Automatic water level

controller, Ammeter, Voltmeter each with two way

selector switch incoming, wires duly socket crimped,

main contactor & overload relay, start - stop push

buttons, to be erected on angle iron frame grouted on

wall as directed. The isolator, overload relay &

contactors will be of L & T, Siemens or BCH make only.

20 Providing & erecting weather proof, dust & vermin 2.0 Sq. 14902.55

proof, floor mounted front operated indoor type cubical mtr

panel board having IP-64 protection made from 14 SWG

thick CRC M.S. sheet for outer body & doors, 16 SWG

thick CRC M.S.sheet for internal partitions with

necessary supporting angles, flats including cutting,

bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, with suitable size of

inter connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control fuses for

measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and

rubber gasket complete. The Panel shall be painted with

epoxy powder coating. (The rates excludes the cost of

switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams) The panel shall

be supplied with following approved manufacturers

with following size. (B) The standard companies switch

gear shall be used and only manufacturers at CPRI

approved factory and shall be certified by that company

whose switch gears are used after fabrication for

beneficial use locally fabricated panel box with 350 mm

21 Supplying and erecting triple pole & neutral 440V / 500V 6.0 RMT 1961.42

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence

of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections.(A) Suitable for 100 Amp.

22 Supplying and erecting aprroved make 3 Phase Digital 1.0 set 2834.06

Ammeter & Voltmeter having 3.5 digit LED display 0 to

750 AC volt range for volt meter and 0 to 1000 A for A-

meter erected on existing panel board with all

connection wiring and manufacturer calibtration

23 Supplying and erecting approved make set of indicator 6.0 No 43.43

lamps of LED type lamp, lens cover, Bakelite holder

complete erected with necessary connections.

24 Supplying and erecting APP type capacitor suitable for 25.0 KVAR 287.85

415 v 50HZ 3 phase AC power supply with earting

terminals and test certificate.

25 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 25.0 RMT 378.75

cable multistrand Aluminium conductor for 1.1 KV. to

be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables (D) 3 x 1/2 core

x 70 Sq. mm ( 35 Sq. mm 1/2 core)

26 Providing and erecting LT CT with bar primary 50/05 to 3.0 nos 274.72

1000/05 ration 15 VA burden erected in existing CRCA

box duly secured with insulating material connected to

the meter coil.

27 Supplying and erecting aprroved make PF meter having 1.0 nos 5102.52

150 mm dia balanced and un balanced load to work with

provided CT 100/5 amp to 400/5 Amp ration and other

assesories complete erected in MS box and connected

to circuit by PVC copper core leads

28 Supplying and erecting aprroved make single phasing 1.0 nos 1078.68

preventor in MS enclouser with wiring up to 20 HP

29 Miniature circuit breaker single pole 6A to 32A suitable 2.0 nos 299.97

to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming

to IS 8828/1996 with ISI Mark cat-III

30 Approved make Four pole moulded case circuit breaker 1.0 No. 6173.12

having breaking capacity ICU of 25 KA. at 415 V,having

normal current rating up to 100A. with Fixed thermal &

magnetic release suitable to work on A.C. supply 50 c/s.

with all internal connections & complete erected in

existing 16 G.M.S. housing.Rating - 32 Amp/440 V.

ICS=100% of ICU only Cat III.

31 Supplying ISI Marked (Embossed) following size of Heavy 100.0 Mtr. 804.97

duty “C” Class G.I . Pipe & erecting as directed by

Engineer-in-charge with necessary plumbing as desired.

(G) Nominal 100 mm dia mtr.

32 Supplying & erecting Mild Steel heavy duty Flanges with 20.0 No 212.10

rubber packing and hardware materials for pipe

connections suitable for Nominal Dia : 100 mm dia.

33 Lowering of 15 hp submersible motor pump set 2.0 Job 1284.72

complete with required. Nos. and size of casing pipes

erected by means of proper chain pulley block & pipe

wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe

assembly filled up with water

34 CABLE GLANDS & CABLE LUGS 0.00 -

Supply and fixing heavy duty flange type brass cable

glands with rubber ring for suitable size PVC armoured

cable complete with out going tails, insulating tape etc.

for following size of cable.

a 3.5 core 70 sq mm. 6.0 nos 103.02

b 3 core 35 sq mm for gland 10.0 nos 66.66

c 3.5 core 70 sq mm for lugs 24.0 nos 27.27

d 3 core 35 sq mm for lugs 45.0 nos 22.22

PART - III- Out Door Street Light.

35 7 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm 8.0 No 11411.99

thickness with 225mm X 225mm X 16mm base

plate,Supply and Installtion of 4 nos. 4 - M20 Bolts and

600mm long J-Bolt. (4 Nos. Per St. Lght Pole or Above

Foundation ) Hot Dip galvanised octagonal type

Streetlight Pole complete without Bracket & accessories

with following specifications.(a) Overall length of pole

: 7.00 mtrs. (b) Height above ground level : 7.00 mtrs.

(C) Length of section - Out side dia. & Wall thickness

Bottom : 135 mm, Top : 70 mm.

36 Providing and fixing of heavy duty Double Compression 8.0 No 38.38

type Brass Cable Gland with rubber ring suitable for 2 to

4.0 Core x 10 Sq. MM PVC Insulated Alu. Armoured cable

complete with outgoing tails, insulating taps etc. - (2

Nos. Glands Per Sintex Box on St. Light Pole)

37 Providing and fixing of Solderless Crimping Type 2.0 No 13.13

Aluminium Lugs (4 Nos. per termination) conforming to

IS suitable for 1 x 4.0 Core x 10 Sq. MM PVC Insulated

Aluminium Armoured cable tail complete erected with

insulating materials for each termination.evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. - (2 Nos. Termination Per

St. Light Pole)

38 Supplying and erecting bakelite sheet 6 mm thick 68.0 No 337.80

HYLAM make on existing angle iron frame having the

weight 1 KG & Size suitable to mount on JB with 15A.

way bakelite connector duly erected on existing

board.(incoming & out going cable) with stud type

terminals suitable for 4 C x 16 sq.mm cable with

,Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

capacity double pole 6 A to 32 A, MCB (Cat-III) with ISI

marked suitable to operate on 240 V, A. C. supply and

having overload & short circuit triping element and

breaking capacity 10 kA conforming to IS: 8828 with

mounting clamp with nuts, bolts & washers suitable for

erection on pole with cable clamps & earth bolt. - (1 No.

Per St. Lght Pole) (Hylam Sheet Area = 12 cm X 8 cm =

39 SITC of funnel type pipe earthing having 1.50 Mtr. Long 8.0 No 602.57

and 25 MM dia. Medium Class Galvanised iron pipe with

coupling and buch burried in specially prepared earth pit

with salt & charcoal complete with necessary double

SWG GI earth wire - 0.8 Kg (2 x 3.5 Mtr. = 7Mtr.) laid upto

bolt fitted in pole for earthing . (Earthing at each poles)

as per drawing - (1 Job Per St. Light Pole)

40 Providing and erecting Street Light pole bracket 8.0 No 561.56

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S. sleeve

tubing of approx. 45cms.length and suitable for 76.5 mm

/80mm / required size of pole top having sufficient

fasteners for fixing the brackets and having spread of

1.0.mtr. length with 100 deg.with vertical plane (Boom

angle should be 10 Degree) & suitable welded stays,

reducer and with check nuts complete painted with one

coat of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

SINGLE Arm Bracket 1.0 mtr

41 Supplying and erecting 60 Watt LED street light fittings 8.0 No 4997.48

with High power White LEDs wattage of 1 Watt and

above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses with company mark/name

engraved or embossed 120 to 300 V,Power Factor more

than 0.95, THD < 10 %, CCT 5000 K to 5700K, Uniformity

ratio >0.45, Luminaire efficiency> 85 lumens/watt . LED

driver efficiency > 85 %. CREE / OSRAM / PHILIPS

Lumileds / NICHIA / SEOUL/ LG/BridgeLux (U.S.A.) make

LED used for luminaire. ( Each fittings required LM-79 &

LM-80 certificates) - (1 No. of Luminaire equivalent to

120 W HPSV (8320 Lumens) fitting per streetlight pole,

Surge-4K) (Cat- III)

42 Supplying and erecting Flexible PVC insulated multi 64.0 Mtr 77.77

strand multi core 1.1 kV grade ISI marked copper wires

of following size to be erected as directed FR PVC

insulated ISI Marked Stranded Copper cable having

Conductor 3 Wire 2.5 Sq. MM.,3 core round PVC

sheathed in exising pipe/ in street light pole erected with

2.5 Sq. MM. copper conductor FR PVC insulated

stranded wire of green colour for earth continuity.

43 Providing, laying, erecting ,testing & commissioning of 1 300.0 Mtr. 140.39

x 4.0 Core x 10 Sq. MM, XLPE (IS: 7098 (i) - 88), ISI Mark,

Armoured, Multistranded, Aluminium Conductor

suitable for 1.1 kV grade to be laid at depth 90 Cms

under ground or to be laid on wall with necessary clamps

or in existing cable trench/ pipe at road crossing or on

floor and making the ground as per original. - For

Streetlight between two poles & Service Connections.

44 Providing & laying of approved make 50 MM Nominal 250.0 Mtr. 62.62

OD Doubled Walled Corrugated Pipes (DWC) of

polyethylene (conforming to IS 14930 - II) with necessary

connecting accessories like coupler, Tee, L - Bow, etc. of

same material at required depth (90 cms) including

excavation for laying of cable below ground/ road

surface for enclosing cable and back filling the same to

make ground as per original & as per instruction of

Engineer Incharge - for Streelight Cable of 1 x 4 core x

Sq. MM and Service cable of 1 x 4 core x 10 Sq. MM. (25

Mtr Per Between two Pole)

45 Providing & laying of approved make 90 MM Nominal 50.0 Mtr. 95.95

OD Doubled Walled Corrugated Pipes (DWC) of

polyethylene (conforming to IS 14930 - II) with necessary

connecting accessories like coupler, Tee, L - Bow, etc. of

same material at required depth (90 cms) including

excavation for laying of cable below ground/ road

surface for enclosing cable and back filling the same to

make ground as per original & as per instruction of

Engineer Incharge - for Streelight Cable of 1 x 4 core x

Sq. MM and Service cable of 1 x 4 core x 10 Sq. MM. (2.5

Meter per Pole )

46 Supplying & erecting MINI SECTION PILLAR 60 x 30 x 45 1.0 No 1884.66

cms fabricated from 16 Gauge thick joint legs M.S. Sheet

with angle iron legs 45 cms long made from 35 x 35 x

mm thick. Jointless M.S. Angle with cable clamps to be

burried in ground to have appropriate erection to work

Uniform Until erected with cement concrete foundation

and 45 cms high bricks work finishing with plaster etc.

hinged double door with 3" x 4" vision panel covered

with Mesh & V. panel overlapping with flap for meter

reading internally supported on both side, with internal

and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is

welded and other with nut and bolt for erecting backlite

sheet. Painting the Section Pillar inside and out side with

three tank powder coated paint.. section pillar roof

should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of

47 Supplying and erecting bakelite sheet 12mm thick 1.0 Sq. 2311.89

HYLAM make on existing angle iron frame. mtr

48 Supplying & erecting approved make Digital time switch 1.0 No 3168.37

having lithium cell 6 years operative and operate battery

backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A with,

floating contacts Minimum switching setup time

minimum & LCD display. Also comprised permanent

ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover

erected as required with necessary connection erected

49 Providing & Fixing of 4 pole 440 V 40 A power contactor 1.0 No. 2782.55

for time switch complete erected as per direction CAT-

50 Providing & Fixing of approved make 415 V four pole 1.0 No. 815.07

MCB for lighting load (B Curve) having 10 KA breaking

capacity confirming to IS - 8828, with enclosure having

capacity of 40 A.Cat-III.

51 Supplying & erecting funnel type earthing having earth 1.0 No. 7874.97

plate of following size burred in specifically prepared

earth pit 3 mtr. below ground with 40 kg. charcoal and

salt with alternate layers of charcoal & salt, 20mm.dia.

G.I. pipe with Funnel with a wire mesh for watering &

bricks masonry block, C.I. Cover complete as per para

of IS 3043 with necessary length of double Galvanised

Iron / copper earth wire No 6 SWG bolted with lug to the

plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long

complete connected to the nearest switch gear with end

socket as per direction & duly tested by earth tester

confirming to IS (As per drawing) with following

specification (C) with 60 x 60x 0.315 cms. Copper earth

52 Drilling of Road without breaking the road surface for 40.0 mtr 492.88

laying of cable [A] up to 100 mm bore dia.

53 Making trench in soft soil of suitable width of 90 cm 250.0 Mtr. 55.55

deep for laying cable or locating the fault all over the

run and back filling the same and making the surface as

PART - IV- Electrification for Bore Room

54 Point wiring for Light / Bell with 2-1.5 sq.mm & 8.0 Pt. 449.45

earthwire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper

wires, in following type of pipe to be erected concealed

in/ on surface on wall/ceiling complete with 6A Modular

type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic

box, single mounting base frame covered with

textured/metallic front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (a) with

medium class Rigid PVC pipe and accessories. Cat. III

55 Point wiring for FAN with 2-1.5 sq.mm & earthwire of 2.0 Pt. 638.32

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multistrand copper wires, in

following type of pipe to be erected concealed in /

flushed on wall/ceiling complete with 6A Modular type

switch and hum free EME four or more step type

electronic fan regulator with separately mounted and

accessories with earth continuity of following type

erected on PVC / Metallic box, single mounting base

frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed.(a) with medium class Rigid PVC pipe and

accessoriesCat. III

56 Point wiring for Individual Plug with & earthwire of 1.5 2.0 Pt. 475.71

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper wires, in following

type of to be erected concealed in / on surface of wall /

ceiling complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic box covered with appropriate

front plate modules erected on / in wall / ceiling as per

pipe erected with following type of accessories. [I] For

6A Plug with 2-1.5 sq.mm Cu. Wire. (a) with medium

class Rigid PVC pipe and accessoriesCat. III

57 Providing and erecting ISI mark Medium class RIGID PVC 30.0 Mtr. 33.33

PIPES of following size complete to be erected on/in wall

or ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed

58 Providing and erecting ISI mark Medium class RIGID PVC 10.0 Mtr. 67.67

PIPES of following size complete to be erected on/in wall

or ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed

59 Mains with 1.1 KV grade FRLS PVC insulated ISI marked 50.0 Mtr. 82.82

stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (a) with medium class Rigid PVC pipe and

accessories(b) 2 wire 2.5 sq. mm

60 Mains with 1.1 KV grade FRLS PVC insulated ISI marked 25.0 Mtr. 112.11

stranded Copper conductor wire in following type of

pipe to be erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size(a)

with medium class Rigid PVC pipe and accessories (a)

61 Approved make ELCBs / RCCBs conforming to IS: 12640 1.0 No. 1969.50

and having sensitivity of 30 mA and Short Circuit

withstand capacity of 6 KA and suitable for operation on

single phase 240 V. having characteristic of quick action

& tripping with all advance feature & do not incorporate

any electronic component. for following Max. rating

erected as directed (i) 25 Amps.DP Cat.III

62 Providing & erecting 415 V MCB Four Pole for Motor & 1.0 No. 737.30

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity - ( c ) 63 Amp

63 Providing and erecting Approved make Ceiling fan with 2.0 No. 1596.81

double ball bearing ISI mark with condenser A.C.

23OV.50 c/s.1200 mm. sweep complete, canopy and

cms. down rod erected on existing hook or clamp with

24/0.2 , 3 core flexible wire with earthing. [Make shall

be approved by Engineer in charge]

64 Supplying and erecting Fan Hook of 10 mm.M. S. 2.0 No. 43.43

Roundbar grouted in RCC slab with Making the site as

65 Supplying & erecting fan hook box of 10mm MSRound 2.0 No. 108.07

bar bounded to the RCC bars up to 50 mm length each

side and peirced through 16 gauge MS box/heavy duty

PVC box complete erected in ceiling with necessarry

66 Providing fan clamp of for Ceiling fan complete erected 2.0 No. 98.98

with necessary bolts and nuts..

67 Providing 2.5mm.thick laminated /pvc sheet to cover 2.0 No. 18.18

the fan hook or Fan box.

68 Supplying and erecting 18 W LED indoor fittings with 4.0 No. 1823.05

LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA

polyester powder coated and high U.V. & corrosion

resistance with diffuser and/or Polycarbonate optics

with company mark/name 120 to 300 V,Power Factor

more than 0.9, THD < 10 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7, Luminaire

efficiency> 85 lumens/watt , LED driver efficiency > 85 %

CREE / OSRAM / PHILIPS Lumileds / NICHIA /

SEOUL/Bridgelux(U.S.A.) make LED used for luminaire.

(Each fitting required LM-79 & LM-80 Certificates) (A)

Tube Light with integral driver (ii) 18 Watts, Surge -

2KV,IP-20 conventional 4 feet. Cat-lll.

69 Providing and erecting metallic vitrified danger notice 2.0 No. 81.81

board as per language suggested by engineer incharge

for HIGH VOLTAGE installation to be erected as per IS.-

70 Providing pair of rubber hand gloves suitable for working 1.0 No. 214.12

on 11 KV/22 KV supply.

71 Supplying 12 mm thick rubber matting as per 1.0 Sq. 3081.51

IS:15652/IEC 61111 mtr

72 Supplying stand first AID box with antiseptic cream, 1.0 No. 299.97

medicine for use on wounds due burn, crepe bandage,

gauge bandage, medicated ready to use bandage (Band-

aid) adhesive tape for medicinal user, Scissors, anti-

septic solution (Savlon or similar) etc. (All above

contents shall be of standard makes)

73 Supplying & erecting ABC powder type 'Ceasefire' type 2.0 No. 848.40

Fire extinguisher as per IS 13849 or 1 Kg capacity with

necessary clamp for erection on wall

Say, Total Amount Excl. GST (Rs.) :-

Say, Total Amount Excl. GST (Rs.) :-