ADDITION ALTRATION AND SPECIAL REPAIR TO JCOs, OR MD ACCN IN TARAPORE VIHAR AT SUKNA MIL STATION UNDER GE SUKNA

Amount

B/R PART Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor, etc and jointed in neat cement slurry over and including cement screed 15 mm thick CM (1:6). and pointed in white or coloured cement to match complete all as specified and directed.

All as per Srl Item No. 2.00 here-in-above but in vertical surfaces such as skirting/dado laid over and including a backing coat of 10mm thick Cement mortar (1:3) complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm mm thick as in dado set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing coat with CM (1:3) complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thickness complete all as specified and directed.

M & L for 25 mm thick plain Cement Concrete (1:2:4) type B-0 (using 12.50 mm graded stone aggregate) as in Flooring, etc., finished Concrete Surfaces even and rough to receive cement screed, complete all as specified and as directed.

M& L for PCC lean concrete type E-2 (1:5:10) (using 40mm graded stone aggregate) as in filling and mass concrete or similar work including WPC mixed as per manufacturer instruction complete all as specified and as directed. NOTE : WPC shall be measured and paid separately.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate), 75mm thick as in plinth protection/ paving finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete in (1:3:6) type C-2 (using 40 mm graded stone aggregate), as in surface channels and drains complete all as specified and directed.

Supply only liquid integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed.

M&L Plain Cement Concrete Type B-1 (1:2:4) (using 20 mm graded stone aggregate) in water tank platforms, filling and mass concrete complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20 mm thick pre-polished machine cut kota stone slab in single piece as in treads (including making 3 parallel grooves on kota stone treads), including moulding / rounding the edges of the slab, over and including 20 mm thick backing layer in cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed.

M&L Machine cut kota stone 20-25 mm thick as in riser of steps, skirting, dado etc laid over and including 20 mm thick rendering in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including rubbing/grinding and polishing complete all as specified and directed.

M&L for Granite (of any type) tiles 18-20mm as in platform thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with nosing over 20 mm screed bed in CM (1:4) complete all as specified and directed.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed bed, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for 20mm thick marble tiles machine cut in strips , floor laid over cement screed 15 mm thick CM(1:6) and jointed with grey cement slurry including cutting and polishing of type White Marble - Makrana white complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Taking down of cement plaster any thickness on brick or Stone wall complete all as specified and directed.

M&L 15 mm thick rendering external wall in cement mortar (1:4) finished even and fair without using extra cement complete all as specified and directed.

M&L 15 mm thick rendering internal wall in cement mortar (1:6) finished even and fair without using extra cement complete all as specified and directed.

M&L Rendering 10 mm thick on concrete surfaces as in ceiling in cement mortar (1:3) for finished even and smooth (without using extra cement) complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.50 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkat or frame exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutter of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed.

Refixing shutter of any description exceeding 1 sqm but not exceeding 2 sqm each in same opeining after easing etc complete all as specified and directed.

S & F 2nd Class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 35mm Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 2nd class hard wood rail and style 35 mm thick factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated incl door stopper complete all as specified and directed.

S&F solid PVC Door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel moulded PVC door shutter with particle board core 30mm thick (Stiles) with 2 panel design with 2mm thick moulded PVC sheet on ,4 consisting of frame made out of MS tubes for top & bottom rails, MS frames shall be covered with heat moulded plain colour PVC `C’ channel front face & 2mm plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F aluminium powder coated three track sliding window with 5.5mm thick glass shutters in two track and stainless steel mosquito proofing single shutters in one track 0.56 mm nominal dia of wire and average width of aperture 1.18 mm with good quality bearing ,handle star lock rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of JINDAL or of equivalent make complete all as specified and directed . (a) Bottom frame:20620 b) Top frame and Vertical:20621 (c)Handle(side)20606 (d) Sutter interlock:20724 (e) Shuuer top and bottom:20844 (f) Glazing clip:19352 NOTE : Rate inclusive glass pane and masquoto proofing nets.

M&L for powder coated aluminium frame of sectional size 25mmx30mmx2.5mm thick as in ventilators with movable louvers and fitted with figured glass strips 4mm thick complete all as specified and directed.

S&F MS butt hinges, cold rolled medium weight 100mm in size complete all as specified and directed.

S&F 75 mm MS butt hinges medium weight cold rolled complete all as specified and directed.

S&F aluminium anodized barrel tower bolts of extruded section 150mm in length complete all as specified and directed.

S&F aluminium handle, cast type 150mm in size complete all as specified and directed.

S & F 100mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 100mm Aluminium, anodized, barrel tower bolts extruded section & fixed complete all as specified and directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and directed.

S& F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repair Harrison rails, mild steel, chromium plated with fixing ornamental brackets, stops, rollers etc. complete all as specified and directed.

S& F in repair stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F Mild steel flat iron as in hold fast and similar articles conforming to Fe-290 Gde -E-165 complete all as specified and directed.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

Dismentling boarding of any description, fixed in any position with nails as in cub board Self and partition complete all as specified and directed.

S&F 18/19 mm thick Particles board medium Density, flat pressed, single layer type or three layer type with BWR type adhesive fixed with Screws to timber frame work complete all as specified and directed.

Complete all as per Srl Item No. 49 here-in-above but fixing only .

M & L for 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with necessary clips and other like to aluminium frame work, as in doors, windows, partition etc. complete all as specified and directed.

S&F 100 mm size MS Hasps and Staple , wire type, stove enameled black, including bolt to hinges plate complete all as specified and directed.

S&F 100 mm but hinges, extruded aluminium alloy with galvanished mild steel hinges pin, anodized & fixed, type B-21 complete all as specified and directed.

S & F 75mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L Brickwork with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM (1:6) complete all as specified and directed.

S&F GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in bore of pipe 15 mm including taking down of exisging pipe complete all as specified and directed.

S&F GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in bore of pipe 20 mm including taking down of existing pipe complete all as specified and directed.

M&L for cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

S&F in repairs fancy type bib tap chromium plated 15 mm bore cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs long body bib tap 15mm bore fancy type chromium plated ,cost coper alloy with crutvh or butterfly handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs CP pillar tap chromium plated 15 mm bore with capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm dia stop cock/angle stop cock fancy type chromium plated including CP nipple and socket complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rest complete including provision of lime concrete bedding complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back of size 550x 400 mm including cutting for and pining, in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 ltr capacity syphonic action type white body with MS bracket , inlet ball valve, float handle and flush pipe (for EWC or WC) etc complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT Nuts of length 450 mm complete all as specified and directed.

Supply & fixing 1000 ltrs capacity Rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm bore ball brass valves, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule after dismantling of existing water tanks and removing from site complete all as specified and directed.

S&F 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed.

Dismantling 75/100 mm dia CI pipes including tee, branch piece, bend at any position (wall or laid in trench) complete all as specified and directed.

M & L CI sand cast pipe 100mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and directed.

Except CI sand cast pipe 100mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and as directed.

M & L CI sand pipe 75mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and as directed.

Except CI sand pipe 75mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and as directed.

S & F CI branch piece 100mm bore, double(eaqual or unequal), with parallel branches and fitted with oval access door complete all as specified and as directed.

S & F CI branch piece 75mm bore, single(equal or unequal),ordinary or inverted spigot or socketted type with parallel branches and fitted with oval access door complete all as specified and as directed.

S & F CI bends 75 mm bore with oval access door complete all as specified and directed

S & F CI bends 100 mm bore with oval door access complete all as specified and directed

S & F CI cowls 75 mm complete all as specified and directed.

S & F CI cowls 100 mm complete all as specified and directed.

S & F for 100 mm bore of pipe stack clamp out of 50mm x 5 mm flat iron and 16 mm dia round iron stay including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F for 75 mm bore of pipe stack clamp out of 50mm x 5 mm flat iron and 16 mm dia round iron stay including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

M&L for 75mm dia cast iron floor/nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4) complete all as specified and directed.

M&L for 100mm dia cast iron floor/nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4) complete all as specified and directed.

S & F in repair 40mm (HDPE) of pressure rating 6 Kg/f/CM2 fixed complete to walls ceilings or in floors etc complete all as specified and directed.

Taking down any layer of water proofing treatment including plaster , PCC of any thickness complete all as specified and directed.

M & L for roof treatment including the following :- (i) Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. (ii) M & L for 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) including WPC as per manufacturers instruction as in top of roof. (iii) M & L 10 mm thick rendering on roof surface in cement mortar (1:4) finished even and fair including WPC as per manufacturers instruction without using extra cement. (iv) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric laid on primed surface by forced application complete all as specified and directed. (v) Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces. (vi) Apply 2 coat of aluminium paint over APP membrane .

M&L RCC nominal mix 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slab supported on walls ,beams and coloumns in floors,roofs,landings, kitchen slabs etc complete all as specified (Reinforcement shall be measured and paid seperately) including demolition of old concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing complete all as specified and directed.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick etc complete all as specified and directed.

Dismantling ceiling boards, any thickness including cover fillets old frame work any type complete all as specified and directed

S & F for Anodised aliminium snap grid frame work for false ceiling confirming IS:733, 737 & IS:1285 ; complete all as specified and directed.

S&F 4mm thick (E-Boards) Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws in ceiling complete all as specified and dirceted.

Dismantling wrought iron or mild steel work of any description, in any position complete all as specified and directed.

S & F Rolled mild steel in Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. - Fe 410 -W (Gde-E-250) quality-A complete all as specified and directed.

Dismantling Asbestos Cement with ridge (Corrugated, Semi corrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F Prepainted galvalume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws including dismantling of old sheets complete all as specified and directed.

S&F pre painted galvalume aluminium zink coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding / eves fixed with self tapping screws to frame complete all as specified and directed.

S&F in repair stain less steel Towel rail complete all as specified and directed.

S&F in repair swivel shower of brass chromium plated with long head for fixing with 15 mm pipe complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F kitchen plate rack made out of 0.63 mm stainless steel sheet & of size not less than 24" x 30" x 10" , standard quality fixed with brass screw complete all as specified and directed

M&L for complete removal of exisitng treatment of old decorated surfaces of wall applying two coat of oil emulsion distemper over a coat of primer over one or more coat of wall care putty (approx 1.5mm thick) for obtained smoothness of wall surfaces complete all as specified and directed.

M&L for prepration of new plastered surfaces of wall and applying two coat of oil emulsion distemper over a coat of primer over 1.5mm thick of wall care putty on wall surfaces complete all as specified and directed.

M&L for Preparation of new ceiling surfaces and two coats of distemper over a coat of primer over one coat of putty (0.5 to 1mm thick) complete all as specified and directed.

M&L for complete removal of exisitng treatment of old decorated surfaces of ceiling applying two coat of oil emulsion distemper over a coat of primer over a coat of wall care putty(0.5 to 1mm thick) for obtained smoothness of wall surfaces complete all as specified and directed.

M & L two coat of Synthetic enamel paint over a coat of pink primer on new wooden surfaces including prepareation of surface over 10cm width or girth complete all as specified and directed.

M & L one coat of Synthetic enamel paint on old wooden surfaces including prepareation over 10cm width or girth complete all as specified and directed.

S&F Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar (1:3) complete all as specified and directed.

S&F for rolled mild steel in Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. Fe 410 -W (Gde-E-250) quality-B complete all as specified and directed.

S&F Welded steel wire fabric wood or steel members - Weight per square metre - N exceeding 4 kg complete all as specified and directed.

S&F Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment - S & F - Fe 410 -W (Gde-E-250) quality-B complete all as specified and directed.

S & F 3.15mm dia wire Plain mild steel wire, galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. complete all as specified and directed. NOTE : Eeach line of wire to be measured .

Removing and Hacking of existing deteriorated damaged & loose concrete from the external surface of the structure carefully by low impact high frequency hammer or by manual chipping without damaging the existing concrete or control sand blasting including cleaning the surfaces by air jet etc, complete and also without damaging the existing structure.The rate shall also include disposal of waste/rubble/malwa from site outside MD Land upto as directed by the Engr-in-Charge along with lead and lift if any including standard steel scaffolding upto a height of 7 M complete all as specified and directed. NOTE : The above treatment will be done in presence of company authorised person and also company skilled workers.

Removing the loose scale of corrosion etc from the exposed reinforcement and cleaning the corroded reinforcement by wire brush followed by cleaniong with air blower/ water jet . Finally cleaning the rusted reinforcement / metal (iron base) by Chemical rust remover , cleaning and etching agents with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel for about 5-7 days. Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth. as per technical specifications and also as per manufacturers recommondations and also as per directions of Engineer-in- charge. The rates inclusive of labourers, materials , tools etc complete in cluding standard steel scaffolding upto a height of 7 M complete all as specified and directed. NOTE : The above treatment will be done in presence of company authorised person and also company skilled workers. Make of the Rust removing agent : Reebakelens RR from M/s Fosroc or Equivalent Makes M/s SIKA, M/s Pidilite etc.

M & L for surface cleaning and application of Two coats of Two component epoxy zinc rich primer coat on steel surfaces / reinforcement as per manufacturer's recommendation and as per technical specification and also as per the direction of Engr-in-Charge, complete including standard steel scaffolding upto a height of 7 M complete all as specified and directed. Make of Two component epoxy zinc rich primer : Nitozinc Primer from M/s FOSROC and Equivalent M/s SIKA, M/s Pidilite etc. NOTE : The above treatment will be done in presence of company authorised person and also company skilled workers.

Re-Bar Anchor: Providing and fixing shear connectors of 10 mm dia by drilling 12 mm diaholes on the concrete surface to a depth of 100 mm using a rotary cum hammering drilling machine as per technical specification and throughly cleaning the hole using compressed air and water jet and anchoring with pure Epoxy resin based anchoring grout solution complete all as specified and directed. Make of Epoxy based resin grout : LOck Fix E77 from M/s FOSROC and Equivalent M/s SIKA, M/s Pidilite etc. Note : The above treatment will be done in presence of company authorised person and also company skilled workers.

Crack Sealing : Identify the cracks and construction joints, honeycomb areas, shall be chased open into ‘U’ groove shape and sealed with High strength, abrasion -resistance epoxy reinstatement mortar, Fosroc Nitomorter S or Equivalent of M/s Sika, M/s Pidilite etc, Providing and fixing 6-8mm dia nozzle along the joints and honeycomb areas afterproper surface preparation. The injection of Conbextra EP10 or Equivalent through the nozzle till the refusal of the grouting materials complete all as specified and directed.

M & L for providing and applying Structural grade long pot life, Two component Epoxy resin concrete bonding agent prior to building up of secion with any type of mortar / concrete to ensure bond between old concrete and new concrete by brush application as per manufacturers instructions and also as per technical specifications complete all as specified and directed. NOTE : The above treatment will be done in presence of company authorised person and also company skilled workers. Make of Two component Epoxy resin concrete bondin agent : Nitibond EP from FOSROC or Equivalent M/s SIKA, M/s Pidilite etc.

M&L for 25 mm thick( Average thickness) Guniting concrete surface using mechanical means with single component, shrinkage controlled, polymer modified, fibre reinforced structural grade cementitious repair mortar having compressive strength of 45 N/ Sq.mm , Flexural strength of 7 N/Sq.mm and tensile strength of 2.50 N/sq.mm at 28 Days all as per manufacturer's recommendation and technical specification and as per the direction of Engr-in-Charge including standard steel scaffolding upto a height of 7 M complete all as specified and directed. NOTE : The above treatment will be done in presence of company authorised person and also company skilled workers. Make of single component, shrinkage controlled, polymer modified, fibre reinforced structural grade cementitious repair mortar : Renderoc SP 40 from FOSROC or Equivalent M/s SIKA, M/s Pidilite etc.

M&L for providing and laying of ready to use non shrink ,cementitious free flow micro concrete, upto required thickness at the designated areas, to the prepared slurry tight shuttering with proper shear connectors and bonding agent where ever necessary .The fluid Micro-concrete repair material shall be single component , cement based to which only site condition of water and approved graded coarse aggregate where ever specified shall be permitted . The micro concrete shall contain no mettalic aggregates or chlorides and shall be shrinkage compensated in the plastic state. The micro concrete in the flowable consistancy should achieve a compressive strength of 50 N/ Sq.mm after 28 days at 30 degrees Centigrate as per BIS 4551-80.The unrestrained expansion shall be between 1-4 % as per ASTM C827 -1987. Again as per BS 4551-80 the flexural strength shall not be less than 5 N/ Sq.mm @ 28 days. The Micro Concrte shall have a coefficient of thermal expansion 10-12 x 10 -6 /oC and thermal conductivity 1.50 W /moC . The mixed density of micro concrete shall exceed 2100-2200 Kg/Cu.M 227oC including standard steel scaffolding upto a height of 7 M complete all as specified and directed. NOTE : The above treatment will be done in presence of company authorised person and also comapany skilled workers. Make of non shrink ,cementitious free flow micro concrete micro concrete : Renderoc RG of FOSROC or Equivalent M/s SIKA, M/s Pidilite etc.

PATH Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M & L Hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface using broken boulders or stones complete all as specified and directed.

M&L for Cement concrete 75mm thick, (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set and jointed and pointed in neat cement slurry in floor with grey cement and pigment over cement screed 15 mm thick in CM 1:4 including dismantling complete all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M & L Providing PCC type B1, (1:2:4) (using 20 mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

SPECIAL ITEM M & L Preparing the new surfaces of walls plastered, and applying two coats of exterior weather paint over one coat of primer over a coat of putty on wall surface complete all as specified and directed.

M&L for complete removal of exisitng treatment of old decorated surfaces of wall applying two coat of exterior weather paint over one coat of primer over a coat of putty on wall surface complete all as specified and directed.

SEWAGE DISPOSAL Excavation in trenches not exceeding 1.5 m wide & not exceeding 1.5 mtr deep in soft and loose type of soil complete all as specified and directed.

M&L for 150 mm dia Sail-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

M&L Concrete bed type C-2 (1:3:6) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150 mm bore of pipe complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L Brickwork with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM (1:6) complete all as specified and directed.

M&L 15 mm thick rendering on wall in cement mortar (1:4) finished even and fair without using extra cement complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L pre cast RCC type B1 (1:2:4) (using 20mm grade stone aggregate) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thickness complete all as specified and directed.

M& L for PCC type D-2 (1:4:8) (using 40mm graded stone aggregate) as in foundations filling and mass concrete or similar work complete all as specified and directed.

M & L Cement concrete in surface channels and drains TypeC2, (1:3:6) ( using 40 mm graded stone agregate complete all as specified and directed.

M & L Providing, cement concrete type B1, (1:2:4) (using 20 mm graded stone aggregate) as in copings complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed. NOTE : Inner girth only to be measured.

Returning, filling in, including spreading, leveling, watering & well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

E/M PART M&L for point wiring for light points / ceiling fan points / exhaust fan points/ Wall fan points/call bell points controlled by one, one way switch with (FRLSH) PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including , PVC medium grade Concealed conduit not less than 20mm dia with MS sheet metal sunken box switch/Terminal box 1.2 mm thick and phenolic laminated sheet cover 3.0 mm thick and brass screws with cup washers all necessary wall cutting and making good disturbed surface and including taking down old unsv ones complete all as specified and as directed. NOTE :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) cutting chases shall be included in the unit rate.

All as per Srl Item No. 146.00 here-in-before but for one 6 amps socket out let point on the same board with other switches complete all as specified and directed.

All as per Srl Item No. 146.00 here-in-before but for one 6 amps socket out let point on independent board complete all as specified and directed.

All as per Srl Item No. 146.00 here-in-before but for one socket outlet 16 amp on independent board with 2.5 Sq.mm cable and 2.5 Sq.mm earth wire complete all as specified and directed.

All as per Srl Item No. 146.00 here-in-before but for one light point controlled by two, 2-way switch complete all as specified and directed.

M&L Sub main wiring power/circuit using FRLS, PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 2.5 Sqmm, earth continuity conductor of size 2.5 Sqmm to be drawn through and including PVC conduit 20mm dia medium Grade Concealed in walls/roof/floors including taking down old unserviceable ones complete all as specified and as directed. NOTE :- (i) Two single core wires of 2.5 Sqmm and one wire of 2.5 Sqmm and one run of PVC conduit shall be measured as one unit). (ii) The unit rate included for making good the disturbed surface including finishes to match with the adjoining surfaces alongwith cutting chases) .

All as per Srl Item No 151.00 here-in-before but 2 Single core of size 4 Sqmm and earth continuity conductor of size 4 Sqmm complete all as specified and as directed.

All as per Srl Item No 151.00 here-in-before but 2 Single core of size 6 Sqmm and earth continuity conductor of size 6 Sqmm complete all as specified and as directed.

S & F Switch piano 6 Amps single pole one way incluing taking down old unsv ones complete all as specified and as directed.

S & F Switch piano 5 Amps single pole two way incluing taking down old unsv ones complete all as specified and as directed.

S & F Switch piano 5 Amps single pole bell push incluing taking down old unsv ones complete all as specified and as directed.

S & F Socket outlet 5 Amps 3 pin flush type incluing taking down old unsv ones complete all as specified and as directed.

S & F Switch Socket combination 16 Amps 3 pin flush type incluing taking down old unsv ones complete all as specified and as directed.

S & F Stepped type fan regulator flush type incluing taking down old unsv ones complete all as specified.

S&F ceiling rose, 3 phase /PVC/ polycarbonate isolated body incluing taking down old unsv ones complete all as specified and as directed.

S &F Bell buzzer, Ding Dong AC. 230 volts, single pole incluing taking down old unsv ones completed as directed.

S&F Lamp holder, PVC/ polycarbonate type with cord grip cap suitable for pendate fittings including taking down old unserviceable ones complete all as specified and as directed.

S&F in repairs LED battery backup inverter bulb of Lamp wattage: - 12 Watts, Battery: - Not less than 2200mAh or not less than 4 hrs backup,Efficacy: - Not less than 120 Lm/Watt including taking down old unsv ones complete all as specified and directed.

S&F in repairs LED bulb wattage: - 9 Watts,Efficacy: - Not less than 110 Lm/Watt including taking down old unsv ones complete all as specified and directed.

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 2200 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. MAKE : Cat ref LUMILINEPLUSBS20WLED865SPCSS of Havells or Cat ref LDL-20-CDL of Crompton or Cat ref BCLSB 20W WH of Bajaj.

S & F in reapir Surface and wall mounted LED batten 10 watt 2ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1100 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. MAKE : Cat ref. LUMILINEPLUSBS10WLED865SPCSS of Havells or Cat ref LDL-10-CDL of Crompton or Cat ref BCLSB 10W WH of Bajaj.

S & F in repair LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF ≥0.95, total System Lumens 1000 lm, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed. MAKE : Cat Part No. HEXAFT10WLED857SSYMBOPC of Havells or Cat ref LBHP-10-CDL of Crompton or Cat ref BIBWP 10W LED WH of Bajaj.

S & F in repair LED Street Light 20 watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥100 Lm/W, 5 kV Surge Voltage Protection,Operating Voltage range 140 V - 270 V complete all as specified and as directed. MAKE : Cat Part No.ENDURAPEARLSL20WLED757SASYTOPCMP of Havells or Cat ref LSTS-20-CDL-M of Crompton or Cat ref ENXT P 24L WH CR PC SD of Bajaj.

S&F VTPN DB,MCCB incomer,4 ways double door,Metal door ,IP-43 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 250+24 complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unserviceable ones complete all as specified and directed. MAKE :Cat ref 507759 of Legrend/L&T or equivalent as approved by GE.

S&F MCCB 4P 125 Amps 415V ,50 Hz ,breaking capacity 16 KA including dismantling taking down unsvericeable one complete all as specified and directed.

S&F MCB ,SPN DB, 12 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including dismantling taking down unsvericeable one complete all as specified and directed.

S&F MCB SPN 40 Amps 240V ,50 Hz ,breaking capacity 10 KA," C " series. Including dismentling taking down unsvericeable one complete all as specified and directed.

S&F MCB SP,10KA, 230V, C-curve, 6-32 amps incl dismentling taking down unserviceable one complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead wire of 4 sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismentaling old unsv ones complete all as specified and as directed.

S&F GI tubing light grade 40 mm dia for protection pipe along the wall to TPN DB for protection of cable complete all as specified and directed .

S&F Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps,240V for Geysor connection complete all as specified and directed.

S&F Exhaust fan for ventilating porpose AC single phase 230/240 V of size 300 mm sweep with metal body and metal blades grey in colour complete all as specified and directed.

S&F PVC Exhaust fan for ventilating porpose AC single phase 230/240 V of size 250 mm sweep and metal blades white in colour complete all as specified and directed.

S&F PVC Wall fan AC single phase 230/240 V of size 400 mm sweep and metal blades white in colour complete all as specified and directed.

S&F in repair of energy saving BLDC ceiling fan Type of motor: - Brush Less DC Motor (BLDC) and Input Power: - 26 to 32 watts with full speed and reduced power consumption with reduced speed technology and RPM: - 340 to 375 rpm and Sweep: - 1200 mm and without remote complete all as specified and directed.

BLANK

M&L for cutting and making and enlarging existing hole for fixing of exhaust fan, nuts, bolts washer including plastering and make good the disturbed surface with the existing all as specified and directed.

S&F Storage type Smart water heater 25 ltr capacity, vertical type, energy efficient , 5 - star rated white, Slim body with remote control with and including PVC inlet & outlet connection pipe (Hot & Cold) 450 mm long and necessary grouting bolts on wall and connection complete all as specified and directed. MAKE : Havells Adonia R cat part Ref GHWCARTWH025 or equivalent as approved by GE.

M&L for fixing GI tubing 15 mm bore medium grade on wall/floor with necessary fittings and fixure (including necessary tank nipple & connection from service Tank upto water heater) complete all as specified and directed.

S&F gun metal , globe or gate valves, with iron wheel head , screwed both ends for iron pipe of dia 15 mm complete all as specified and directed.

BLANK

S & F Bib tap 15 mm dia standard of PTMT any colour screwed, for iron pipe & fixed complete all as specified and directed.

S&F of glow sign board of size 18x10x4 inch made up of pressed steel of 2mm thick with 6 nut welded for 6 nos machine screw front covered with 3mm thick blue acrylic sheet fixed on shunkan box with 6 nos machine screws. The acrylic sheet should be digitaly printed with qtr no.( to be provided by Engr-in-charge) max 8 letters of 20mm width and 150mm height, red coloured. inside box 5W LED Lamp pin type both side with 02 nos holder complete with connection with the light point in front side of building and with all fixing arragement complete all as specified and directed.

BLANK

S&F TV socket complete all as specified and directed.

S&F PVC conduit 20mm dia (for lan cable/TV cable) complete all as specified and directed.

SCHEDULE OF CREDIT DEDUCT Credit Amount B/F from Serial Page No. 22 against Schedule of Credit

M/S AHUJA TRADING

M/s HARI BHUSHAN GHOSH & Co.

MS ORIENT ENGINEERING WORKS