PROVN OF DISPENSARY DRUG STORE ROOM WITH BUILT IN SHELVES AND PROVN OF COVERED SHED FOR PARKING OF UNIT VEHS AT 161 MH AT MIL STN PITHORAGARH

Amount

DESCRIPTION OF ITEMS

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in harde/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation, stay rods, laying of underground cable etc and getting out in hard/dense soil complete all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum,in soft/disintegrated rock and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and as directed.

Removing excavated material n .exc 50 m and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed.

M & L for hard core of broken stone or boulders gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface of broken bricks aggregate, all as specified.

M & L for filling dry sand under floor including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified.

Filling under floor (except material) including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified.

M & L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and as directed.

M & L for treating top surface of filled earth at the rate of 5 litre per sqm of surface with anti termite chemical emulsion complete all as specified.

M & L for treating the soil under plinth protection at the rate of 5 litre per sqm of surface with anti termite chemical emulsion complete all as specified.

M & L for treating the soil along with external perimeter of building at the rate of 2.25 litre of anti termite chemical emulsion per sqm of the perimeter wall complete all as specified.

M & L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M & L for Cement concrete type C2 (1:3:6) 40 mm graded aggregates in foundations, filling and mass-concrete complete all as specified and as directed.

M & L for Cement concrete type C2 (1:3:6) 40 mm graded aggregates in Cement concrete in surface channels and drains all as specified and as directed.

M & L for PCC type B-1, 1:2:4 using 20 mm graded stone aggregate as in lintels upto 1.5m clear as in span, cills, copings, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M & L for providing cement concrete 1:2:4 of type B0 using 12.5 mm graded stone aggregate 40mm thick as in damp proof course to horizontal or slapping or vertical including necessary form work and applying evenly a coat of hot blown type bitumen at the rate of 1.50 Kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and as directed.

M & L for RCC M-25 (Design Mix) as in foundation, including raft, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and as directed.

M & L for RCC M-25 (Design Mix) as in columns, pillars, piers etc complete all as specified and as directed.

M & L for RCC M-25 (Design Mix) as in beams, cantilever, lintels etc complete all as specified and as directed.

M & L for RCC M-25 (Design Mix) as in slabs supported on walls, beams and columns in roofs, landings, balconies, canopies and shelves etc complete all as specified and as directed.

M & L for RCC M-25 (Design Mix) as in chajjas complete all as specified and as directed.

M & L for use and waste of form work to sides and soffits of roof beams, lintels, lever shelves incl supports over hang etc rough finished surfaces of concrete flat all as specified and as directed.

M & L for use and waste of form work to soffits of suspended slabs such as roof slab landings and similar works n exc 200mm thick (horizontal or slopping) for rough finished surfaces of concrete flat all as specified and as directed.

M & L for use and waste of form work to chullah hoods, chajjas and similar items incl edges rough finished surfaces of concrete flat all as specified and as directed.

M & L for use and waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and as directed.

M & L for use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams or similar works vertical or to batter for rough finished surface of concrete complete all as specified and as directed.

M & L for use and waste of form work to sides of pillars, posts, struts, columns for rough finished surface of concrete complete all as specified and as directed.

M & L for precast cement concrete Block Masonary with soilid blocks type C1 1:3:6 20mm graded stone aggregate exc 10cm in width and setting in mortar 1:6 complete all as specified and directed.

M & L for 15 mm thick cement plaster on fair faces of brick work or concrete surface on wall in CM 1:4 finished fair and even complete all as specified and directed.

M & L for 15 mm thick cement plaster on fair faces of brick work or concrete surface on wall in CM 1:6 finished fair and even complete all as specified and directed.

M & L for 5mm thick rendering in CM 1:4 on ceiling, soffits, chajja projection complete all as specified and directed

M & L 15mm thick cement plaster on fair faces of brick work or concrete surface on wall in CM 1:4 mixed with waterproofing compound 3% weight of cement or as per manufacturer's instruction, finished fair and even complete all as specified and directed. (WPC will be measured separately)

M & L for 15mm thick screed bed in CM 1:4 mixed with water proofing compound as per manufacturer instruction , finishing the surface should be even and fair with out using extra cement, complete all as specified and directed. (WPC measured separately)

Supply only water proofing compound, complete all as specified and directed.

M & L for water proofing treatment to roofs surfaces including a coat of cold applied bituminous shalitex primer @ 0.30 Lit per sqm evenly on roof surface and a coat of hot blown bitumen 85/25 @ 1.2 kg/sqm shall be applied on primed surface and laying of 3mm thick APP modified polymeric membrane (weight not less than 3.0 Kg/Sqm) unrolled and bonded completely to the substrate with side over lap of 75 mm & end over lap of 100 mm and then scaled/ fused by flame or bitumen and a coat of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm shall be applied on top of APP modified polymeric membrane as per manufacture instruction and finally it will be finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm, complete all as specified and as directed.

M & L for mild steel TMT bars 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Description same as above but, 6mm dia and over and incl 10mm dia as in stirrups, spacers and binders

S & F pressed steel frames of size 125x60mm (using PBI sheet 1.25 mm thick) for doors with one or more rebates including necessary fixing lugs, hinges,lock strike plate, etc Including cement concrete 1:3:6 type C-0 (using 12.5mm graded stone aggregate) as for filling in door frames etc complete, as specified and as directed.

S & F 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 35mm thick IInd class hard wood glazed skelton shutters open rebated and prepaired to recive glass,guage etc (W/o sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of sutters as specified in SSR part - I section - 8, clause 8.20 (a). S&F to chowkhat complete all as specified and as directed.

S & F Aluminium, anodised, barrel tower bolts 200 mm of extruded section and fixed complete all as specified and as directed.

S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300 mm and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S & F 150 mm long Aluminium handles, cast type, anodised and fixed complete all as specified and as directed.

S & F steel window with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed welded complete all as specified and directed.

S & F steel window with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed welded complete all as specified and directed.

S & F steel ventilators with top hung shutters including hinges, steel handle and steel peg stay complete with glazing sash, dovetailed or welded complete all as specified and directed.

S & F M.S. Framed work such as grills grating etc. with ends of bars sholdered and / or riveted into spikes, framed guard bars, frames for iron doors, ladders and similar all as specified directed.

S & F Mild steel plain black sheets 1.00mm thick as in hearths; covering to door shutters; covering to door chowkats (frames); waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required

S & F for steel work in tubular trusses incl special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and as directed.

S & F mild steel as in plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified and as directed.

M & L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F Mild steel wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M & L MS Plates (plain or chequered) channels Fe 410-W (Gde E-250) quality B. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane all as specified and directed.

S & F Anodised aluminium frame powder coated (n. less than 50 micron) for doors, windows, ventilators etc any section with one or more rebates including joining cleat for fixing, glazing clips, rubber neoprene packing, snap beading, screws, handles, hinges and other necessary fittings as required and as directed by Engr-In-Charge complete.

S & F sheet glass 5.5 mm thick ordinary quality and glazing with/without oil putty in square exc 0.5 sqm in each pane all as specified and as directed.

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L for GI wire netting 0.90 mm dia and 12 mm mesh lathing to wood or metal studding, joists etc in walls, ceilings, beams etc including all laps, cutting and waste complete all as specified and as directed.

S & F 28mm dia fancy type wooden finish MS dropery rod fixed with wooden finale stop, brackets etc to wall complete as sample approved all as specified and directed.

M & L for three coats of white wash on ceiling/Chhajja (undecorated) surfaces including preparing of surfaces complete all as specified and directed.

M & L for applying two coats of oil bound distemper on new plastered surfaces of wall including preparation of new surface.by applying birla care putty to get smooth surface complete all as specified and directed.

M & L for preparation of new (Previously untreated) plastered surfaces of walls and applying two coats of cement based paint on walls over a coat of alkali resistant priming paint complete all as specified and directed.

M & L preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer on new wooden surfaces all as specified and directed.

M & L preparation of new steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and directed.

M & L for non-skid joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but n exc 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Ditto all as per item No 66 but on vertical surfaces over 10 mm thick rendring in CM 1:4

M & L for galzed ceramic coloured tiles 350x250x6 to 7mm / 450 x 350 x 6 to 7 mm/ 450x300x6 to 7mm thick on walls etc set & jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces over &.incl 10mm thick rendering in cement mortar 1:4 for laying wall tiles etc complete all as specified and directed.

M & L for chequered tiles rubber moulded decorative designed coloured cement concrete tiles 25 mm thicksize of tiles as approved set, jointed and pointed in neat cement slurry with grey cement and pigments in floor over and including 15 mm thick screed bed with cm 1:6 complete all as specified and directed.

M & L for granite (of any type) work (table rubbed and polished) 15-18mm thick in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed of CM (1:6) and including rounding to edges of stone slabs complte all as specified and as directed.

M & L for granite (of any type) work (table rubbed and polished) 15-18 mm thick for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding to edges of stone slabs complete all as specified and as directed.

M & L for 75mm thick PCC 1:4:8 of type D-2 using 40mm graded stone agrregate as in sub base of floors etc complete all as specified and directed.

M & L for PCC 25mm thick 1:2:4 of type B1 using 20mm graded stone aggregate as floor finishing surface complete all as specified and as directed.

M & L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) as in plinth protection laid in alternate panels 75mm thick finished even and smooth w/o using extra cement complete all as specified and as directed.

M & L for 100mm thick PCC 1:4:8 of type D-2 using 40mm graded stone agrregate as in sub base of floors etc complete all as specified and directed.

M & L for 100mm thick PCC 1:2:4 of type B-2 using 40mm graded stone agrregate as floors etc and spike rolling to surface or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

Forming construction joints 30mm deep x10mm wide filled with sealing compound grade "A" complete all as specified and as directed.

Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

M&L for point wiring Concealed type with 1.5 Sqmm, single core (FRLS), PVC insulated with multistranded unsheathed copper conductor cable including rigid non- metallic PVC concealed conduit 20 mm or higher dia, light grade ISI marked complete with all PVC conduit accessories / fittings and sunk switch boxes with 3 mm thick plastic laminated hard glossy surface sheet (white) top cover, including continuous earth wire of PVC insulated, unsheathed, green in colour 1.5 Sqmm multistrand copper conductor (FRLS) connected to all fittings, sunken boxes and common earth and connected to earth dolly, screwed with Brass screws, cup washers complete all as specified and directed for the following :-

(a) One light point/ fan/ exhaust fan point/bell point controlled by one, one way switch of 5/6 Amps.

(b) One 3 pin socket outlet 5 Amp on same board with other switch

(c) One 3 pin 5/6 amps socket out-let point on independent board controlled by one, one way switch of 5/6 amps on independent board.

All as per item 79 herein above but with 2.5 Sq mm cable (FRLS) for one 15 Amp socket outlet controlled by one switch on independent board and 1.5 Sqmm PVC insulated unsheathed multi stranded copper conductor cable as continuous earth wire complete.

S & F Switch piano, flush type, white finish, 5/6 amps, single pole, one way.

S & F Socket outlet 3 pin, 5/6 amps and 2 pin 5/6 amps flush type, complete all as specified and directed.

S & F ceiling rose, surface bakelite, AC, 220/240 volts, 3 terminals, complete all as specified and directed.

S & F lamp holder, insulated body with back plate suitable for batten /angular fittings, fixed on with & including round block 8 cm dia, 4 cm depth, closed recessed type & making connection etc complete all as specified & directed.

S & F Switch piano flush type, white finish, 15/16 amps, single pole, one way, complete all as specified and directed.

S & F Socket outlet two in one 3 pin 5/6 amps and 3 pin 15/16 amps (multipurpose), flush type, non shutters, non inter locking type, complete all as specified and directed.

Supply and fix LED Integrated Batten T5 box type surface mouted, (1x18 Watt) prewired including electric electrical connection with PVC insulated twin twisted copper wire of size 0.75 Sqmm from ceiling rose to tube light fitting complete all as specified and directed. Make:- Havells/Philips/wipro/Crompton

Supply and Fix LED 9 W bulb complete all as specified and directed. Make:- C&S/Philips/Wipro/Crompton

Supply and Fix 1x20 watt LED security light fitting, pressure die-cast aluminium including fixing the same of GI pipe 25 mm dia bore light grade bracket, 1.5 mtr long including necessary cutting / bending /welding and fixed the same with two Nos FI clamps of 40x 4mm duly painted and suitable size of nut & bolts etc. and making electric connection with two core copper flexible wire of 0.50 Sqmm complete all as specified and directed. Make:- C&S/Bajaj/Philips/wipro/Havells

Supply and Fix MCB DB sheet metal enclosure for DB, TPN, 4 way having protection with 200 amps rated bus bar, 440 volts, double door, including grauting suitable for housing MCB's and isolators complete all as specified and directed.

Supply and Fix in MCB Triple pole & Neutral 240 volts, 63 amps, of 10 KA complete all as specified and directed. Make : Legrand /ABB/Havells /L&T

S&F MCB DB sheet metal enclosure for DB, SPN, 8 way having protection with 200 amps rated bus bar, 240 volts, double door type, suitable for housing MCB's and isolators,concealed in wall complete all as specified and directed. Make-Legrand/Havells / CG / L&T / ABB /Schneider

Supply and Fix in MCB single pole, 240 volts, 6-32 Amps of 10 KA complete all as specified and directed. Make : Legrand/Havells / CG / L&T / ABB /Schneider

Supply and Fix in MCB single pole, 240 volts, 40 Amps of 10 KA complete all as specified and directed. Make : Legrand/Havells / CG / L&T / ABB /Schneider

Supply and Fix in MCB single pole & Neutral 240 volts, 6-32 amps, of 10 KA complete all as specified and directed. Make : Legrand/Havells / CG / L&T / ABB

Material and Labour for earthing complete with galvanized steel earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 m deep below normal ground level, connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts and washers of galvanised iron or steel all as shown in earth plate No 3 of MES schedule 2009 part – I connected to earthing test point including earth continuity conductor and loop earthing etc. as required 4 mm dia galvanized iron or steel wire including necessary excavation and earth work, concrete pit & chamber in PCC 1:2:4 type B1 & pit cover 75mm thck in RCC 1:2:4 type B1 duly reinforced with 6mm dia bar @ 150 c/c both ways including with lifting handle and Earth lead and GI protection pipe light grade 15 mm dia beyond 7.5 mtr from electrode to earth terminal point /main switch board and 20mm bore GI watering pipe medium grade etc. complete all as specified and directed.

Supply and laying XLPE LT 1100 volts underground earthed cable, PVC bedded, galvanized steel strip or wire armoured, electric power cable heavy duty 1100V with multi stranded, aluminum conductor of cross sectional area 4 core x 16 Sqmm including laying, testing and commissioning complete all as specified and directed.

Supply and laying XLPE LT 1100 volts underground earthed cable, PVC bedded, galvanized steel strip or wire armoured, electric power cable heavy duty 1100V with multi stranded, aluminum conductor of cross sectional area 4 core x 10 Sqmm including laying, testing and commissioning complete all as specified and directed.

M & L for sand cushioning with dry and clean sand over and under the under ground cable in trenches, ducts for cable protection incliding levellling and consodilation complete all as specified and directed.(Compacted thickness shall be measured.)

M & L for laying well burnt bricks,as in protection of cable laid dry, flat aboutting each other wide wise all as directed by Engineer-in-Charge.

M & L for GI tubing 40 mm dia light grade for cable protection all as specified and directed.

M & L GI tubing medium grade complete with all fittings laid in trenches/ walls for the size 25 mm dia bore all as specified and directed.

M & L GI tubing medium grade complete with all fittings laid in trenches/ walls for the size 20 mm dia bore all as specified and directed.

M & L for cutting of existing pipe and making threading and sutable work work for connection for pipe all as specified and directed.

S & F Gun metal gate valve screwed both end with iron head wheel size 25mm dia bore all as specified and directed.

S & F Gun metal gate valve screwed both end with iron head wheel size 20mm dia bore all as specified and directed.

S & F ceiling fan complete with accessories 230 V,1200 mm sweep, BEE 5 star rated complete all as specified and directed. Make: Bajaj / Usha / Khatian

S & F Electronic fan regulator flush type, 300 W Step type, 230 volts ISI marked complete all as specified and directed. Make: Anchor / Havells / crompton

S & F and installation of water heater storage type geyser of capacity 25 liter, ISI marked, minimum BEE 5 rating complete grouting of 4 Nos new bolts of required size, in wall and tightening the nuts, washers and making connection complete all as specified and directed. Make: Jaguar Elite Ser / Bajaj / CG / Havells

Supply, fixing and testing of refrigerator electric driven (single phase), capacity 310 Litres, double door, BEE 5 star rated including vegetable crispers, toughened glass shelves, base stand drawer, chilller compartment, with manufacturer warranty complete all as specified and directed. Make: Samsung / LG / Whirlpool / Haier

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 0.5 KVA complete all as specified and directed.

Supply and fixing of exhust fan AC single phase 230/240V of size 450 mm sweep with louvrs complete all as specified and directed. Make: Bajaj / CG / Havells

Supply and install feeder box water proof of size 75x60x45 CM mounted on 50x50x5MM angle iron frame factory made having 3phase 4 wire for connecting incoming and out going cables of various sizes with min 4 nos cable gland suitable for various cables at bottom and painting of feeder box with two coats of aluminium paint over a coat of red oxide primer incl fixing of MCB TPN 4 way ans 15 Amp socket complete all as specified and directed

M/s J P Traders