SPL REPAIR OF STAIRCASE OF BLDG NO 48 OF HQ 122 INF BDE, PROVN OF COVERED SHED OLD-10 JCO MESS OF 8 ASSAM AND PROVN OF SENTRY POST AT MANGAL VIHAR UNDER GE BARRACKPORE

Amount

Surface dressing n.exc. 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep in soft/loose soil and getting out complete all as specified and as directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation, laying of pipe or for shafts, wells cesspits, man holes, pier holes, laying of cable etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm in soft / loose soil complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

Bringing approved earth (as approved by Garrison Engineer) from sources outside defence land including all costs such as royalty if any transportation taxes etc. for area filling / forming including raising earth spreading in layers not exc 30 cm thick each layer, watering, compaction with 8 tonne to 12 tonne power roller and finished to required size and shape etc, any high / depth from EGL. Notes:- (i) Earth required for the item shall be supplied by contractor out side MOD land of any lead at his own arrangement. (ii) All cost of procurement of earth including cost of transportation, compaction, royalties, tax etc. shall be deemed to be included in the unit rate quoted by the contractor. (iii) with reference to clause 3.6 of MES schedule Part-II on serial page no- 21 it is clarified that measurement of the above item shall be finished embankment/ traverse of filled earth after consolidation/ compaction and 5% deduction shall be made from measured and calculated volume to allow for increase in bulk. (iv) Total quantity/ partial of earth may not be available in Barrackpore area. The contractor shall bring the earth outside area it is advised to quoted the rate considering availability of soil and its lead involved complete all as specified and as directed.

Demolition of plain cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for hard core with broken stone or boulder of gauge not exc 63 mm, deposited , spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surfaces complete all as specified and as directed.

M&L for PCC 1:4:8 Type D-2 ( Using 40 mm graded crushed stone aggregate) as in foundation , filling, and mass concrete complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for PCC 1:3:6 Type C-2 ( Using 40mm graded crushed stone aggregate) as in foundation , filling, and mass concrete complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for PCC 1:3:6, type C2 (using 40 mm graded crushed stone aggregate) as in surface channel or drain including necessary form work complete all as specified and as directed.

M&L for 75 mm thick PCC 1:2:4, type B2 (using 40 mm graded stone crushed aggregates) as in path / paving / hard standing / floor complete all as specified and as directed.

M&L for 50 mm thick PCC 1:2:4 type B2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for PCC 1:2:4, type B1 (using 20 mm graded crushed stone aggregate) as in coping, cills, hold fasts, fixing of post, water trough, lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, etc. including necessary formwork (straight or curved) complete all as specified and as directed.

M&L for Damp proof course in cement concrete, 25mm thick type 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

M&L for RCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in foundations, footings, foundation beams, plinth beams, bases for columns, etc. complete all as specified and as directed. Note : Reinforcement will be measured and paid seperately.

M&L for RCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in columns, pillar, piers, posts and struts etc. complete all as specified and as directed.

M&L for RCC, 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in beams, seismic bands, cantilevers, bressumers and lintels over 1.5 m span complete all as specified and as directed.

M&L for RCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc. complete all as specified and as directed.

M&L for RCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in Chajja etc.complete all as specified and as directed.

Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter fair finished flat surfaces of concrete complete all as specified and as directed.

Use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions (Square, Circular rectangular or polygonal) for fair finished flat surfaces of concrete complete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintels over 1.5m clear span, cantilevers, shelves including supports overhangs etc also splays between floors and beams for fair finished flat surfaces of concrete complete all as specified and as directed.

Use and waste formwork to soffits and sides of suspended slabs such as roof slabs, floor slabs, landings sun shade, chajja, floors, roofs, landings, balconies etc., n exc 200 mm thick (horizontal or sloping) for fair finished surface of concrete complete all as specified and as directed.

Use and waste of form work to chullah hoods, chajjas, troughs and similar items including edges for smooth finishes complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, roof slab treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for flat, fair finished surfaces complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and as directed.

M&L for mild steel TMT bars 8 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M&L for Cutting holes for superficial area exc. 150 sq.cm but n-exc 400 Sq cm into or through brick walls built in Cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 complete all as specified and as directed.

M&L for brick work with subclass ‘B’ bricks, (locally available best quality) straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4) complete all as specified and directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following of treatment/specification from bottom to top:- (i) M&L 10mm thick screed bed in cement mortar (1:4) using water proofing compound complete all as specified. (ii) M&L applying evenly a coat of oil based bitumen primer confirming to IS-3384 on roof, canopy, chajja, parapet ( vertical surfaces etc ) @0.40 litre per sqm by the same membrane manufacturer of density 250C, 0.87 to 0.89 litre And viscosity 70-160 cps after proper cleaning of the roof surface (Horizontal/vertical) and providing APP based polymeric membrane min weighing 3.6 kg/sqm and min 3mm thick reinforced with polyester non wove fabric ( weight not less than 150 gms/sqm ) laid on primed surface with side overlap of 100mm and end overlap 150mm, using bitumen torch or by LP gas torching & sealing all joints etc and ensuring complete thermos fusing and applying one coat of aluminium paint complete all as specified and as directed. (Note:- (i) Water proofing treatment shall be done by the approved authorised applicators.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound @ 200Ml per bag(50Kg) of cement or as per manufacture's instructions, finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as "Supply only".

M&L for rendering 5 mm thick in cement mortar (1:3) as in ceiling surface finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying one coat of alkali resistant primer over a coat of 2 mm thick (average) wall care putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of oil bound distemper complete all specified and as directed

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for complete removal of existing finishes/treatment of wall and applying two coat of oil bound distemper over one coat of primer including 2 mm thick(average) wall care putty complete all as specified and as directe.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using Airless Paint Primer Sprayer using smart technique over 1.5 mm thick (average) wall care putty on newly plastered surface of wall including preparation complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 -W (Gde?E- 250) quality A complete all as specified and as directed.

S&F Rolled mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated Fe 410-W (Gde E-250 quality A) complete all as specified and as directed.

S&F Rolled mild steel Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete conforming to Fe 410-W (Gde E-250 quality A) complete all as specified and as directed.

M&L for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to grade Fe-410-W (Gde E 250 quality A) for fixing complete all as specified and as directed.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290, Gde-E-165 completed all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and as directed. Note: To be executed for provision of ridges and hips.

Dismantling timber scantling 40Sqcm and over in section as in framed work in any position complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

MM&L for 2nd class hardwood boarding, 40 mm thick Planed one side & edges tongued and grooved or rebated, and ditto as in Floors and Skirting complete all as specified and as directed.

M&L for 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F factory made solid PVC door frame of size 40mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc with plain, chamfered or rounded, mitred beads (without sash bars) for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed.

S&F 100 mm size stainless steel butt hinges, complete all as specified and as directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

S&F 300 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators, partitions etc. with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters (sliding type), aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified and as directed.

S&F 3mm thick frosted glass, ordinary quality and glazing with rubber beading in square not exceeding 0.50sqm in each pane complete all as specified and as directed.

S&F stain-less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F 25mm aluminium powder coated single curtain rod ( thickness not less than 1mm) including funnels etc complete all as specified and as directed.

S&F aluminium brackets( Heavy duty), powder coated of best quality as approved for fixing 25mm bore curtain rod fixed in wall complete all as specified and as directed.

Dismantling timber scantling framed work under 40sqcm in section in fillets, rails, rafter, purlins etc fixed with nails/screw etc complete all as specified and as directed.

M&L for 2nd class hard wood, in scantlings, clean sawn wrought timber as in framed work complete all as specified and as directed.

M&L for 1st Class Hard wood 35 mm wrought treads with rounded nosings, with 20 mm wrought risers on tongued both edges, glued, wedged and blocked complete all as specified and as directed.

M&L for 1st Class Hard wood 40 mm wrought riser with rounded nosings, risers, glued, wedged and blocked complete all as specified and as directed.

M&L for 1st class hardwood Newel posts, wrought, with square, rounded, chamfered or stop, chamfered edges, mortices for strings and handrails, sectional area exc. 100 mm x 100 mm and fixed complete all as specified and as directed.

M&L for 1st class hardwood Rounded and mitred ends to tops of newels ends & caps etc complete all as specified and as directed.

M&L for 1st class hard wood 100×75mm moulded Handrails rounded or shaped with splayed faces in straight lengths and fixed complete all as specified and as directed.

M&L for 1st class hard wood section n exc 50 x 50mm Balusters, rounded, square wrought and fixed, with ends housed (square or splay) to handrails and treads or strings complete all as specified and as directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and as directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old work with two or more coats complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

M&L for vitrified ceramic tiles, light shade, 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for vitrified ceramic tiles, light shade, 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in skriting dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for coloured joint free non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc. over and including 15 mm thick screed bed in cement motar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, complete all as specified and as directed.

M&L for glazed light coloured/printed ceramic tiles 350x250x7mm/450x350x7mm thick in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry pointed in white or coloured cement to match colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for pre painted, polished chequered cement concrete tiles in floor, area exc 0.06 Sqm but not exc 0.11 Sqm, 25 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with colour pigment to match with the tiles over and including screed bed of 20 mm thick cement mortar (1:6) including dismantling of old tiles of any description complete all as specified and as directed.

S&F 60 mm thick machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 M-35 Grade over and including 50 mm thick sand bed complete all as specified and as directed.

S&F 500 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I with and including 20mm bore dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed.

S&F 20mm bore gun metal globe or gate valve cast copper alloy, screwed down, high pressure with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S&F GI tubing15 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F GI tubing 20 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F bib taps 15mm dia cast copper alloy chromium plated, fancy type with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directe.

S&F fancy type Brass chromium plated 600mm long Towel Rail fixed with screws and wooden/plastic cleats etc. complete all as specified and as directed.

S&F health faucet chrome plated fancy type with push bottom flexible steel pipe with PVC lining of 1.2m long suitable for 15mm pipe complete all as specified and as directed.

S&F Vitreous China Wash hand basin with matching pedestal type, white/colour flat back size 630x450 mm including brackets and pillar tap, 15 mm bore chromium plated, cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia 450mm long PVC connection pipe complete all as specified and as directed.

S&F vitreous china wash down water closet (padestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for padestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets,PVC connection pipe 15mm dia, 450mm long etc complete all as specified and as directed.

S&F Vitreous china urinal, half stall white (excluding flushing cistern) including urinal spreader, 450mm long PVC connection pipe , 32mm PVC waste pipe & 32mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and laid in trenches or in floor/wall complete all as specified and as directed. Note : Earth work shall be measured and paid separately under respective item.

M&L for pcc 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in bed for drain pipes 110/100 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

S&F 75mm bore PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends with access door any radius complete all as specified and as directed

S&F 75 mm dia PVC (SWR) bends with access door any radius complete all as specified and as directed

S&F 110mm dia PVC (SWR) junction single, (single T) equal or unequal provided with access door complete all as specifiec and as directed.

S&F 75mm dia PVC (SWR) junction single, (single T) equal or unequal provided with access door complete all as specifiec and as directed.

S&F 75 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F GI tubing 25 mm bore, medium grade with all fittings and fixed complete laid in trenches/wall/floor complete all as specified and as directed. Note : For item no 119 & 120 Earth work shall be measured and paid separately under respective item.

S&F GI tubing 20 mm bore, medium grade with all fittings and fixed complete laid in trenches/wall/floor complete all as specified and as directed.

S&F stop valves, 25mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F stop valves, 20mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

M&L for Cutting the existing pipe of size 25 mm pipe and making new connection including provision of TEE complete all as specified and as directed.

M&L for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in and including PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit for one light/fan/wall fan/exhaust fan/bell point controlled by one No, one way 5/6/10 Amp switch complete all as specified and as directed. Note: Cutting chases for concealed type point wiring including making good the same with plaster/putty and Modular boxes with cover plate is deemed to be included in quoted rate.

All as per item serial No 124 here-in-before but for One 3 pin 5/6/10 Amp switch socket outlet on independent board.

All as per item serial No 124 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable and earth continuity wire with 2.5 Sqmm cable for 6 pin 15/20 Amp socket outlet on independent board.

S&F Modular switch 1 way 6A/10A, 1 module, single pole one way 240 volts complete all as specified and as directed.

S&F modular switch socket combination 2 in 1, 6 Amp/10Amp, 240 volts, shuttered type complete all as specified and as directed.

S&F Modular switch socket combination shuttered type, 6/16A or 10/20Amp, 240 volts. 2/3 pin combined 2 module complete all as specified and as directed.

S&F lamp holder, insulated, PVC / polycarbonate /bakelite body including 12W LED bulb complete all as specified and as directed.

S&F ceiling rose surface bakelite, 65x50mm three terminal complete all as specified and as directed.

S&F decorative box type 20/22-watt light fitting, blue coloured end caps, pre-wired, and including providing PVC/Wooden round/square block -02 Nos and connected with LED fitting to ceiling rose and including LED T-8 tubular lamp of 20 Watt extruded aluminium/PC body and PC diffuser complete with inbuilt LED driver complete all as specified and as directed. Make of light fitting: Crompton Model No.DMLN1LT8-16/Havells Model REGALBATTENT8UPTO1X22WSSBSWH/Bajaj Model No BLRB-DB 218 or equivalent make in Philips Make of LED Rod Crompton Model No.LT8-20-865-2 / Havells Code No.PHOTONULTRA1213T8SSTL20WLED865SPC/Bajaj Model No BLRB20CW LED or equivalent make in Philips

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed. Make:- Havells Model HEXAFT10WLED857SSYMBOPC or equivalent Model of make : Philips / Crompton /Bajaj/Wipro.

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 Watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Make: Havells/Crompton Greaves/Bajaj

S&F exhaust fan of any type/size sturdy engineering plastic exhaust fan 300 mm sweep,1200 rpm, 240Volts, AC, 50Hz as approved colour and connecting of electrical connections and testing including wall cutting finishing and fixing arrangements complete all as specified and as directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and as directed.

S&F single pole & neutral DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or L&K Cat No DESPN008DDS or equivalent model in Siemens / Schneider/Havells.

S&F MCBs, SPN 40 to 63 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed.

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed.

Supply, laying and testing XLPE Insulated , PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16 sqmm 4 core laid in trenches /floor or fixed on wall/pole in existing or new location including brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

M&L for sand cushioning with dry river sand in trenches for cushioning of underground cable including spreading, leveling, punning down the thickness of sand upto 18cm and consolidated complete all as specified and as directed. Note: Punned thickness of sand cushioning will be measured and paid.

M&L for sub class ‘B’ old size well burnt brick laid flat in trenches with length of brick perpendicular to length of cable, over the cable for protection of LT cable complete all as specified and as directed.

M&L for earthing in replacement complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cm X 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I complete all as specified and as directed.

PUNAM ENTERPRISE (BID ID -3497120)

S S ENTERPRISE (BID ID -3497220)