REPAIR TO JOINERY, PLASTERING, FLOORING AND SANITARY FITTING FOR HAWS AT GULMARG UNDER GE 969 EWS.

Amount

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site. Complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & tom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F aluminium anodised 100 mm long Butt hinges with galvanised mild steel screws complete.

S&F aluminium anodised barrel tower bolts, 150 mm long complete.

S&F Aluminium anodised handles, cast type anodised 125 mm long complete.

S&F 2nd class 30 mm thick soft wood (Kail) glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats size of members of shutters as specified in SSR Part - I section 8 Clause 8.23 (b) for windows, ventilators etc are provided with stiles and rails, Complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames).

S&F pressed steel frames for door of size 105 X 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6. Complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood 35 mm thick plain, framed, panelled shutters (any number) with panels of timber flat on both side (feather edge) or of veneered particle board medium density, wood particle board with commercial face veeners and fixed to chowkats Complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in bed block of hold fast etc Complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc 1.00 sqm and n exc 2.00 sqm each and removal from site.

S&F 2nd Class Soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints. Complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats. Complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc 1.00 sqm and n exc 2.00 sqm each and removal from site

M&L for 19mm thick prelaminated particle boards, solid core with decorative face veneers on both faces fixed with screws to timber frame work.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanished, width of flaps (when open) 30mm.

S&F galvanised mild steel wire cloth 0.46 mm nominal dia of wire and avarage width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple. Complete all as specified and directed by Engineer-in-Charge.

S&F MS Cold rolled Butt hinges medium weight 100 mm long complete all as specified.

S&F MS Cold rolled Butt hinges medium weight 75 mm long complete all as specified.

S&F 300 mm size mild steel ordinary rat rail rod pattern springs including roller and roller plate complete.

S&F 300 mm long aluminium sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minium of 6 bolts and nuts four on bolt plate and two on stapple plate and fixed

S&F mild steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed 200 mm long.

S&F mild steel pressed handles, oval type ISI marked stove enamelled black complete all as 150mm size specified and as directed.

S&F Aliminium anodised handles, cast type anodised 125 mm long complete.

S&F Aliminium anodised barrel tower bolts, 200 mm long complete.

S&F Aliminium anodised barrel tower bolts, 150 mm long complete.

S&F Brass mortice lock four levers vertical type size 65mm, 2 levers complete all as specified and directed by Engr-in-charge.

S&F Brass Cylinder Lock heavy model of big size fancy type complete all as specified and directed by Engr-in-charge.

Hacking out old broken glass from wooden/metal frame of any thickness incl punching or drilling out old glazing pins/springs clips and providing and fixing new ones complete all as spcified.

S&F Sheet glass 5 mm thick ordinary quality one way glazing with rubber gasket in square not exc 0.5 sqm each pane, complete all as specified.

M & L for sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames

All as per item No. 32 above but pin head type, figured glass

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) and boarding any thickness, including cover fillets complete all as specified and directed.

M&L for 4 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with screws to timber frame work on ceiling etc. Complete all as specified and directed by Engineer-in-Charge.

M&L for 4 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with screws to timber frame work in partition, wall panelling etc.

S & F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 and not exceeding 13 Sq. cm complete all as specified and directed.

S & F second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with nails, cross sectional area not exceeding 3 Sq. cm complete all as specified and directed.

M&L for 2nd class soft wood 20 mm thick in facia boarding fixed with nails in any situation planed one side with butt joints. Complete all as specified and directed by Engineer-in-Charge.

S&F 2nd Class softwood weather boarding clean swan, plain 20mm thick or feather edges 15mm to 20 mm thick and fixed with 30mm over laps, Complete all as specified and directed by Engineer-in-Charge.

All as per Srl No 40 above but except boarding.

S & F 2 nd Class softwood boarding in floor and skirting 40mm thick planed one side with but joint & fixed with nails.for repairs to existing floor in patchs etc

All as per Srl No 42 above but except boarding fixed with nails

M&L for 2nd class soft wood (kail) prelaminated wooden flooring as in boarding in floors incl 5mm thick foam, 15mm thick, planed one side and edges tongued and grooved or rebeated as in flooring fixed with nails in floor,Complete all as specified and directed by Engineer-in-Charge. Note: Colour and shade of tiles shall be approved by GE and contractor shall not have any claim whatsoever on this account.

Dismantling timber scantling 40 sq cm and over in section in any position as in unframed work, Complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd Class soft wood (Kail) as in scantling, clean swan timber fixed, Complete all as specified and directed by Engineer-in-Charge.

All as per sr item no.46 above but except timber.

Dismantling of plain or corrugated steel sheeting , any gauge and thickness in roof covering including Nainital or similar pattern roof covering Complete all as specified and directed by Engineer-in-Charge.

S&F 0.63 mm thick, galvanized, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs,walls etc with grade of zinc coating 120 grams per square metre Complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No.49 above but except sheeting.

S&F 0.80 mm thick plain , galvanised , mild steel sheeting , in ridges, hips, valley gutters, drip and straight flashing ( length and girth as fixed ) with grade of zinc coating 275 grams per square metre Complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new zinc (or galvanized) surfaces to receive painting by coating with mordant solution including washing and cleaning etc. of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer. Complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coasts of synthetic enamel paint (for steel surfaces) over a coat of red oxide to steel surfaces.

M&L for preparing wood or wood based surfaces of any description applying two coat of synthetic enamel paint over a coat of pink primer Complete all as specified and directed by Engineer-in-Charge.

M&L for preparing wood or wood based surfaces of any description over 10 cm width or girth and applying French polishing including a coat of wood filler on new works with two or more coats complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for non skid ceramic tiles 7 to 8 mm thick coloured and painted (square/rectangular) area of each tile exc 0.06 Sqm but n.exc 0.11 Sqm. in floors set and jointed over cement screed base 15mm screed bed in CM 1:6 and pointed in white or coloured cement to match complete colour painted.

S&F glazed ceramic coloured tiles 7/8 mm thick 600 x 300mm size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 15mm thick cement sand screed (1:4) complete all as specified.

S&F non vitrified coloured tiles of 10 mm thick coloured and painted (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm in floors, over and including 15 mm thick screed in CM (1:4) set and jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified.

All as per sr item no. 60 above but on vertical surfaces such as skirtings etc.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & smooth, without using extra cement Complete all as specified and directed by Engineer-in-Charge.

S & F in repair PVC low level flushing cistern of 10 litre capacity inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make

S&F vitreous China wash hand basin with pedestal, white, flat back size 550x400mm excluding tap, chain, plug but including brackets and cutting for providing ends of brackets fixed in repair Complete all as specified and directed by Engineer-in-Charge.

S & F in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440 X 260 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor. Complete all as specifed and directed by engr-In-charge.

S & F in repair Vitreous Ware wash down water closet (Pedestal), white including flush pipe and plastic water closet seat, black closed pattern with flat bottom and cover and mild steel chromoium plated amluminim hinging device etc complete all as specifed and directed by engr-in-charge.

S & F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality

S & F in repair 15 mm bore Angular stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed all as specified

S&F in repair 15 mm dia bore Chromium plated fancy type Pillar tap screwed down high pressure with or without lettred Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete

S&F in repair central hole basin mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15mm dia bore pipe Complete all as specified and directed by Engineer-in-Charge.

S&F wall mixer with telephonic shower for mixing hot and cold water screwed down for iron pipe and fixed for 15mm dia bore pipe fixed in repair all as specified.

S&F in repair 15 mm dia bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges.

S&F corner glass shelf assembly consisting of 5.5mm thick sheet glass with chromium plated bracket guard complete all as specified.

S&F in repair CP soap tray fixed to walls with rubber plugs complete all as specified and directed.

S&F Fancy type CP towel ring Complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm dia bore chromium plated bib taps, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S&F 125mm dia grating doom with/without waste hole of PTMT (Minimum weight 40 gms)

M/S ABDUL MAJID LONE