Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Fee/PreQual/Technical/Finance NO 1 7 NGEF QUARTERS NEAR ESI OFFICE NGEF LAYOUT BYAPPANAHALLI BANGALORE BANGALORE KARNATAKA 560038 | BENGALURU URBAN | KARNATAKA | 560038 | Admitted-Fee/PreQual/Technical/Finance |
Tender Value
Refer Docs
Closing Date
31 May 2023, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
THE ADMIRAL SUPERINTENDENT
Naval Ship Repair Yard Naval Base Karwar 581308
UNDERTAKING 12K ROUTINES ON DG 3 and 4 ONBOARD NAVAL VESSEL
2023_NAVY_596548_1
REG/2051/12K/DG 3 AND 4
Single
Marine Services
Item Rate
90 days
Karwar
Please refer Tender documents.
2 documents required · 2 mandatory
₹0
Exempted
1 Jun 2023
18 May 2023
1 Jun 2023
19 May 2023
31 May 2023
19 May 2023
Amount
(a) Carry out D Checks :- (i) 6000H2 -Fuel system: (aa) Clean and calibrate injectors and record test pressure in service log. Also change injector inlet screen. (ab) Replace rocker cover gaskets. (ac) Adjust valve tappet clearances within limits and record in service log. (ad) Replace fuel pump filter (screen and magnet). (ae) Calibrate PT fuel pump and record in service log. (ii) 6000H3- Air system: (aa) Clean turbocharger, compressor wheel and diffuser (ab) Check turbo charger radial/end bearing clearance in-situ. Note: Renew ‘O’ ring and Teflon Gasket when turbocharger is opened for checking clearances. (ac) Torque manifold nuts or cap screws as per specifications. (iii) 6000H4- Charge Air Cooler & Fresh Water Cooler: (aa) Clean the internal passages of Charge air Cooler and Fresh water cooler coolant side using Restore Plus as laid down in operating manual. (ab) Renew coolant in the system. (ac) Inspect Charge Air Cooler air side and if required clean using hot water and pressure test up to 2kg/cm2. (iv) 6000H6- Check thickness of vibration damper at 0,90,180 and 270 Degree positions. Replace damper if variation of the 4 reading exceeds 0.010 inch (0.25mm) or exceeds max allowable thickness. Checks to be undertaken in coupled condition. (v) 6000H8- Check crank end clearances with a dial indicator, attaching against damper Min-0.13mm, Max-051mm. (vi) 6000H10- Alignment checks: (For NT/NTA 855 series engines) Undertake alignment checks between the generator and engine and restore radial/ axial initial alignment to 25% of the max limit. (vii) 6000H11- For 1710/28GC1 engines- Undertake inspection of two representative pistons liners and bearings of the engine. Inspection of balance liners and bearings is to be scheduled based on inspection report of the two sample liners. (b) Carry out SR Checks : Offer performance assessment trials on external load tank to DTTT/ETMA and vibration trials to MTU. Crankcase blow by/engine smoke condition is also to be recorded along with all other performance parameters. Trial teams to forward recommendations. For 1710/28GC1 engines- Remove all cylinder heads for decarbonisation and inspect main/connecting rod bearing. Undertake replacement of liners if pitting/corrosion observed on the extracted liners. Refit cylinder heads and bearings as required for other engines - Undertake random inspection of two representative liners and bearings of the engine. Inspect other liners/bearings in case deteriorated. Following inspection and examination cylinders to be carried out: - (a) Gauging and inspection of one liner from each bank for corrosion/pitting post extraction. (b) Gauging of connecting rod big end bearing clearances and examination of big end shell for the cylinder opened. (c) Check condition of valve gear bracket, transfer sleeve sealing ring and injector tube. Inspection of valve gear parts and valve seat inserts of the cylinder head opened. (d) Examine crank pin surfaces and check for ovality and wear. (e) Examine pistons for wear and gauge piston ring clearances. Renew rings if necessary. (f) Examine lub oil pump drive for wear. Renew Rubber vibration dampers where fitted. Carry out load trials under external lode tank.
SPARES
Gasket Governor Set
Plug ,Pipe
Kit Barrel Plunger & INJ
Flange, Tur oil drain
Hose Plain
Hose Flexible
Kit Piston Asse.& Ring Set
Screw, Captive washer cap
Screw, Hexagon head cap
Elbow, Male union
Hose Flexible
Clamp, T Bolt
Hose, Plain
Gauge, Sight
Screw, Hexagon head cap
Core, Aftercooler
Key offset woodruff
Connection, exhaust outlet
Connection, exhaust outlet
Set main bearing
Drive, accessory
Pump fuel
Set ,Piston Ring
Hose, Hump
stage.html
html • 0.01 MB
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .