SPECIAL REPAIRS TO ELECTRIC AND WATER SUPPLY INSTALLATIONS AND ALLIED WORKS AT AF STN PHALODI

Amount

Taking down cement plaster of any description on brick or cement concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed.

Demolition of brickwork , PCC solid block or stone/ boulder masonry, built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for precast cement concrete block of PCC 1:5:8 Type C1 masonry with solid blocks , exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Precast cement concrete hollow block masonry type C1 1:5:8 (using 16mm graded stone aggregate) exc. 10 cm in width and setting in cement mortar 1:4 complete all as specified ans as directed.

M&L for rendering 15 mm thick in two layers on stone masonry surfaces or on other than fair faces of brick/PCC block masonry of walls (first layer 10mm thick in cement mortar 1:6 and second layer 5mm thick in CM 1:4 mixed with WPC 3% by wt of cement) and finishing the surface even and smooth without using extra cement complete all as specified and directed. Note :- Supply only WPC shall be measured and paid separately under respective item and complete all as specified and directed.

Supply only integral water proofing compound ISI marked as approved complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for plastering 5mm thick on concrete surface of ceiling in CM 1:3, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over one coat of alkali-resistant priming paint complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling/soffits of chajjas complete all as specified and directed.

M&L for preparing old surfaces plastered or unplastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old plaster surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old plaster surfaces of walls and applying one coat of cement based paint complete all as specified and directed.

M&L for preparation of old painted wooden surfaces and applying one coat of synthetic enamel paint complete all as specified and directed.

-ditto- all as item above but on steel surfaces complete all as specified and as directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n exc 30 cm high on the wall/concrete surface complete all as specified and as directed.

M&L for preparation of old surface of chequered tiles including cleaning, washing and removing all dirt than apply a coats of cement base paint over a coat of alkaliresistant priming paint complete all as specified and as directed.

Taking down wooden/steel chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.50 Sqm each including hardware/iron mongery complete all as specified and directed.

Taking down wooden/steel chowkats or frames with shutters (without taking off shutters from the frame) exc.1.50 Sqm but not exc. 4.00 Sqm each including hardware/iron mongery complete all as specified and directed.

Taking down shutters of any description exc 1.0 sqm and n exc 2.0 sqm each including hardware/iron mongery complete all as specified and directed.

S&F pressed steel frames of size 125X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete complete all as specified and directed.

S&F pressed steel frames of size 105X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete complete all as specified and directed.

S&F for 2nd class hard wood 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- Glass/gauge required shall be measured and paid separately.

Supply only stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F for 2nd class hard wood, 35mm thick factory made second class hard wood (Hollock) plain framed, paneled door shutters (two panel) with lock rail and panel of 9 mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12 mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening as per specification & drawing as applicable to item No 08095 given in SSR Part-II (2010).

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and shown on serial pages No. 142, 143, 144 , 145 & 146 of SSR 2010 (Part-II) and Particular specification & as directed by Engineer-in-charge. Note :- (i) Doors shall be of make :- Rajshri Plastiwood / Sintex /Rotomould / Rotomatic.(ii) The PVC doors shall be fixed as per manufacturer's instructions and as directed.

S&F powder coated (not less than 50 micron thick) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F 4.8mm thick sheet glass, ordinary quality and glazing with oil putty or by aluminium clips in square exc 0.5 sq.m in each pane complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded aggregates) as in bed block etc for embedding hold fast including mould / necessary form and finishing the surface even and smooth without using extra cement complete all as specified and directed.

S&F 300 mm long aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts or extruded section or cast aluminum alloy and fix complete all as specified and directed.

S&F in repair 250 mm long aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts or extruded section or cast aluminum alloy and fix complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 200mm long complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolts of extruded section 200mm long complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed.

S&F in repair 150mm size extruded aluminium anodised handles fabricated type of extruded section fixed with screws to shutters complete all as specified and directed.

S&F in repair 125mm size extruded aluminium anodised handles fabricated type of extruded section fixed with screws to shutters complete all as specified and directed.

S&F 100mm size stainless steel hinges, heavy weight, fixed with ss screws to PVC door / PVC door frame complete all as specified and directed.

S&F 75mm size butt hinges, heavy weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm long (over all length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring etc. complete all as specified and directed.

Hacking out old broken glass (any size, thickness, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty and screws/nails in square n.exc 0.50sqm in each pane complete all as specified and directed. (Note : Rate of scaffolding also incl into the rate of glass pane)

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty and screws/nails in square exc 0.50sqm in each pane complete all as specified and directed. (Note : Rate of scaffolding also incl into the rate of glass pane)

S&F 3 mm thick figured glass, pin headed type and glazing with oil putty in square n.exc 0.50sqm in each pane complete all as specified and directed. Note :- The rate is inclusive of necessary scaffolding.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M&L in repair particle board 12mm thick medium density flat pressed, single layer type or three layer with BWR type adhesive, fixed with screws to timber frame work complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F for factory made mild steel window with side hung shutters including porjecting type hinges with steel handle, and steel peg stay, fixing lungs etc. complete with glazing bars dovetailed or welded complete all as specified and as directed by Engineer-in-Charge.

S&F for factory made mild steel ventilator with top hung shutters including hinges, steel peg stay, fixing lungs etc. complete with glazing bars dovetailed or welded complete all as specified and as directed by Engineer-in-Charge.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

S&F 15mm thick densified tegular edged eco friendly light weight calcium silicate tiles of approved texture spintone/cosmos/Hexa or equivalent of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at jonts to get required length and of size 24x38mm made from o.33 mm thick (minimum) sheet spaced 1200mm c/c and cross ‘T’ of size 24x28 mm made out of 0.33 mm (minimum) sheet, 1200 mm long spaced between main ‘T’ at 600 mm c/c to form a grid 1200x600mm and secondary cross ‘T’ of length 600mm and size 24x28 mm made of 0.33 mm thick sheet to be interlocked at the middle of the 1200x60 mm panel to form grid of size 600x600mm resting on periphery on wall/partition . on perimeter wall angle precoated steel of size ( 24x24x3000mm made of 0.40mm thick sheet with help of rawl plugs at 450mm c/c with 25mm long dry walls screws at the rate 230mm intervals complete as direction of manufacturers instruction

Dismantling structural steel work including doors, gates but excluding framed truss etc.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded in concrete, embedded portion and making good disturbed ground complete all as specified and as direced

Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any weight not exc. 4Kg/Sqm complete all as specified and as directed.

Dismantling of chain link fencing fencing wire mesh, any type complete all as specified and as directed.

Framed work such as grills, gratings etc. with ends of bars shouldred and/or riveted or forged into spikes; framed guard bars; barred iron doors ladders; framed balusters; walk ways; railing; framework of water tanks and similar work confirming to Fe-290 Gde-E-165 complete all as specified and as directed.

-ditto- all as per item above but as in portions frame and hung as gates, incl pintle hinges, stops, hand made sliding bolts, complete all as specified and as directed.

M&L for framed work with confirming to Fe 410-W (Gde-E-250) quality A, as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0

S&F for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in duct cover confirming to Fe-410W (Gde E-250) quality 'A" complete all as specified and as directed.

M&L for welded steel wire fabric supplied and fixed complete to wood or steel members, weight of wire febric n. exc 4.0Kg/Sqm complete all as specified and as directed.

Supply only chain link MS galvanised fencing, 100 x 100 mm in Size or any type complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

Routine maintenance of rolling shutters (with or without gear operated type) of area exc 5 Sqm but not exc 10 Sqm with any height. The maintenance following all as specified. (a) Taking down hood covers for carrying out maintenance and refixing. Dismantling MS & CI works of any description such as sheet shafts cast iron wheel and other accessories etc. (b) Refixing the serviceable shaft helical springs roller lath sheets cast iron wheel etc. (c) Replacement of unserviceable accessories such as shafts helical springs MS lath sheets hood covers cast iron wheels incl drilling welding etc complete. (d) Cleaning, oiling, greasing etc complete of all movable parts all as required. (e) Apply two coat of synthetic enamel paint complete all as dirceted.

M&L for cutting holes into or through cement concrete slabs, chajjas, columns, walls etc. reinforced or otherwise where superfacial area exc 100Sqcm but n. exc 250 Sqcm complete all as specified and as directed.

-ditto- all as per item above but superfacial area exc. 250Sqcm but n. exc. 500Sqcm complete all as specified and as directed.

M & L for fabrication and eracting of sign board/ informantary board of size 750mm X 1000mm (size of aluminium sheet) eraction in position as directed adopting the following speification :- (a) Main post 2 Nos of stainless steel pipe 60mm dia & 1.5mm wall thickness of grade 316, length of each post 2.1mtr (1.80mtr above GL and 0.30mtr below GL). (b) 2 Nos 80mm dia stainless steel hollw round balls weld on each post fixed on each pipe as a cap. (c) Frame around alumimnium sheet fabricated with 25mm size stainless steel square tube with 1.5mm wall thickness including fixing arrangment for aluminium sheet and welded on main post. (d) 2 Nos horizontel stiffener fabricated with stainless steel pipe of 40mm dia and 1.50mm wall thickness welded horizontally between main post at 1.0m above GL and one at Top. (e) 3mm thick aliumiunm sheet cut to size 750mm x1000mm fixed on frame as mention at serial No (c) above. (f) Providing both side of aluimiunm sheet high intensity prismatic grade retro reflective sheeting as base and with cut out massage (legends boarder slletters numerals, site map etc as per design and pattern approved with high intensity prismatic grade retro reflective sheeting, passing as per manufactures instruction. (g) Excavation 2 Nos post hole of size 300mm x 300mm x 450mm in soft loose soil and fixing of main post and filled with PCC 1:2:4 type B1 using 20mm graded stone grade ,removing surplus soil to distance n exc 50 mtr and site clearnce.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum (any type of soil), getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25cm, watering including removing surplus material upto 50 metre and making good surfaces complete all as specified and directed.

S&F nomenclature coloured board containing ACP sheet fixed on MS frame/cement concrete (unreinforced / reinforced) wall of beam, letters sizes upto 30cm to 40cm height on ACP board in different colour to background as directed, complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of reinforced cement concrete in floors, floors (Other than ground floors), beams, chajjas, facias, fins and similar works.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams, man hole covers, fins & facia etc complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as specified and as directed.

S&F TMT MS bar 8mm dia, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (anealed) not less than 0.9mm dia as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or slopy)

Formwork to edges of concrete fair finished surface exc. 10cm but n. exc. 20cm wide (Horizontal or slopy)

Demolition of unreinforced cement concrete of any description and in any position not otherwise specically provided complete all as specified and directed.

M&L for 40mm thick cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in floors, laid in panels of sizes as directed, finished even and smooth with using extra cement complete all as specified and directed.

M&L for glass dividing strips, 3mm thick and 38mm wide as in flooring complete all as specified and directed.

Cement concrete type B2 (1:2:4) (using 40mm graded stone aggregate) 50mm thick in floor finished the surface even and smooth without using extra cement as in plinth protection complete all as specified and as directed.

M&L for plain cement concrete as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and as directing

M&L for PCC Type B-2 1:2:4 (using 40mm graded stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and as directed.

Demolition and breaking up drain pipes salt glazed ware set in CM 150mm bore pipe.

S&F salt glazed stone ware drain pipes of 150mm bore, grade 'A' ISI marked, laid to slope in tranches, jointed in CM (1:1) and tested complete all as specified.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate in bedding in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150mm bore pipe all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecteing new drains of internal dia 150mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as reqd complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete.

M&L for chequered cement concrete tiles 25cm x 25cm x 22mm thick, set, jointed and pointed in neat cement slurry as in floors with grey cement & pigments laid over 20mm thick Screed bed in CM 1:6 over 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) all as directed by Engineer-in-Charge.

M&L for Surface excavation n.exc 30 cm deep and averaging 24cm deep and getting out in soft/loose soil complete all as specified and as directed.

M&L for 75mm thick Hardcore of gauge n.exc 63mm broken stone/boulders, deposited, spread and levelled in layers watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in pathway complete all as specified and as directed.

M&L for 25 mm thick sand filling, spreading over PCC to laying concrete paver block complete all as specified and as directed.

M&L for 80mm thick grade M-40, Machine pressed Precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 fixed with grey cement without pigment complete all as specified and as directed.

M&L for PCC type C-1 1:3:6 (using 20mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, and the like including weathering, slightly rounded for chamfered angles and throating, as directing.

Formation rolling in cutting with power road roller 8 to 12 tonne complete all as specified and as directed.

Removal of surplus soil to a distance n.exc 50m away from the site and depositing where dirceted at a level n exc 1.5m above the starting point complete all as specified and as directed.

Dismantling floor, hearth/wall tiling including cement mortar bedding (but not backing coat), pointed in any mortar, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement sand mortar 1:6 for laying floor finished complete all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 200mm x 7mm thick, on vertical surfaces such as skirting. dados & risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including rendering coat of 10 mm thick in cement sand mortar 1:3 complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over and including 20mm thick cement screed base of cement mortar 1:3 laid and jointed with grey cement slurry and mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 20-25mm thick kota stone slab in risers of steps, skirting, dado and pillar laid over 10mm thick cement rendering in cement mortar 1:3 and jointed with grey cement slurry and mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Prepare the surface of Kota stone flooring for treating the surface with beeswax polish complete all as psecified and as directed.

Taking down existing cast iron soil/waste pipe of any length size fixed on wall/laid in floor with fittings including cutting of holes and making good surface to match with existing complete all as specified and directed.

S&F 100 mm bore cast iron (spun) pipes soil, waste and vent pipes, in any length with or without ears, with cement joints fixed to walls wherever required complete all as specified & directed.

S&F 100mm bore CI bends (any radius), diminishing pieces fitted with oval access doors etc complete all as specified and directed.

S&F 100 mm bore cast iron sanitary connections - short connection pipe of length up to 300 mm with cement joints complete all as specified and directed.

S&F 100 mm bore cast iron cowls complete all as specified and directed.

Taking down existing water tanks exc 250 but not exc 500 ltrs capacity all as specified.

S&F in rotational moulded polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in posotion 500 ltrs capacity including disconnecting and refixing the GI pipe and fittings complete all as specified and as diercted.

Disconnecting existing tanks of capacity 500L, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after cleaning and removing all scale and dirt, etc, from tanks and mouth of circulating pipes etc. complete all as specified and as directed.

S&F in repairs ball valves suitable for 25 mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and directed.

-dotto- but fixed as in new water tank.

Taking up or down existing GI/UPVC tubing and connections with all fittings fixed to wall / ceiling / laid in floor of size 15 mm bore complete all as specified and directed.

Taking up or down existing GI/UPVC tubing and connections with all fittings fixed to wall / ceiling / laid in floor of size 20 mm bore complete all as specified and directed.

Taking up or down existing GI/UPVC tubing and connections with all fittings fixed to wall / ceiling / laid in floor of size 25 mm bore complete all as specified and directed.

S&F of 15mm dia bore GI tubind medium grade incl all fittings fixed to wall/ceiling/laid in floor complete all as specified and as directed.

-ditto- all as per item No. 123 above but 20mm dia bore

-ditto- all as per item No. 123 above but 25mm dia bore

S&F 100mm dia of out let cast iron nahani trap, with grating including joining to waste pipe fixed in cement concrete type B1 ( 1:2:4) complete as specified and directed.

S&F in repairs grating square/round 100 mm dia of stainless steel (minimum weight 25 grams) complete all as specified and directed.

S&F in repairs 10 liter capacity PVC valve less syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs standard size, vitreous china, Anglo Indian wash down water closet pan (Pedestal pattern) (EWC) white/colour with trap, seat cover including flush pipe, anti syphonage to soil waste pipe fixing bolts and connecting to drain and to flushing cistern complete all as specified and directed.

S&F in repairs pillar taps, cast copper alloy with capstan head, chromium plated suitable for 15mm bore dia of pipe screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed and fly-nuts, screwed for iron pipe or brass ferrule etc complete all as specified and as directed.

S&F in repairs 32mm bore waste coupling, brass, chromium plated for glazed ware basin with long screwed shanks and fly-nuts, flanged end bedded in red lead cement and other end fixed to discharge pipe (half or full threaded) complete all as specified and directed.

S&F brass chromium plated, tubular towel rail, 20mm dia; D type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed.

Supply only PVC waste pipe 32mm dia for wash hand basin complete all as specified and directed.

S&F in repairs chromium plated cast copper alloy shower rose 125mm size with swivel joint fixed to 15mm bore pipe complete all as specified and directed.

S&F in repairs PVC connections 15mm size of length 600mm high density polyethylene pipe with two brass unions complete all as specified and directed.

S&F in repairs chromium plated bib taps, suitable for 15mm bore dia of pipe, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe complete all as specified and as dorected.

S&F in repairs stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle screwed with suitable for 25mm bore GI pipe complete all as specified and directed.

S&F in repairs stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle screwed with suitable for 20mm bore GI pipe complete all as specified and directed.

S&F in repairs stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle screwed with suitable for 15mm bore GI pipe complete all as specified and directed.

M&L for Excavation in trenches n. exc 1.5m deep and not exc. 10Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/loose soil complete all as specified and as diected.

S&F in repairs standard size, vitreous china, white wash down water closet pan (Pedestal pattern) (EWC) white/colour with seat cover including flush pipe, fixing bolts and connecting to drain and to flushing cistern complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings through cement concrete block / stone walling where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10cm girth but not exc 20cm girth

S & F in repair vitreous china wash basin, white, flat back, size 550 x 400 mm including including one No 15mm bore, pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe, one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings such as switches, ceiling rose, pendants, regulators, sockets complete as directed and removing retrieved materials and making good the disturbed surface all as specified and as directed

Point wiring with cable of PVC insulated FRLS copper multistranded conductor 1.5 sqmm 1100 volts grade in and including heavy grade PVC Conduit ISI marked with all accessories and fixing arrangements on wall/ceiling on wall including new PVC gang box fixing on wall surface for housing switches/sockets/regulators etc. with and including 1.5 sqmm PVC insulated FRLS multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for the following :- (a) One light/ fan point controlled by one single pole 5 Amps switch

One switch socket out let point 5 Amps on independent board

One switch socket out let point 5 Amps on same board with other switches

Point wiring with cable of PVC insulated FRLS copper multistranded conductor 2.5 sqmm 1100 volts grade in and including heavy grade PVC Conduit ISI marked broken white/or of cream /grey colour. with all accessories and fixing arrangements on wall/ceiling surface on wall including new PVC gang box fixing on wall surface for housing switches/sockets/regulators etc. with and including 2.5 sqmm PVC insulated FRLS multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for one 15A Switch Socket Combination on independent board complete all as specified and as directed.

Supply and fixing of Piano type switch single pole 5 Amps one way 230 volts complete all as specified and directed.

Supply and fixing of switch socket combination outlet 5pin multi purpose 5 Amps flush type to be fixed in repairs complete all as specified and directed.

Supply and fixing of socket outlet 5 pin multi purpose 5 Amps complete all as specified and directed.

Supply and fixing of switch socket combination outlet 6 pin 5&15 amps multi purpose flush type universal pattern 230 v complete all as specified and directed.

Supply and fixing PVC ceiling rose 65 x 50 mm surface type with 3 terminals complete all as specified and directed.

Supply and fixing of electronic fan regulator step type upto 300watts with 5 step speed control for fans any sweep 1200 mm/1400 mm complete all as specified and directed.

Supply and fix LED Pendent luminaires, 4 feet system wattage of 20 Watts with lumen output of 2000W maintained including fitting fixed on wall/ceiling and connecting of complete with 3 core flexible cable of size 23/0.0076 complete all as specified and directed.

Supply and fix LED batten luminaire surface mounted with extruded aluminium channel, enviromental friendly energy efficient 4 feet system wattage of 20 Watts with lumen output of 2000W maintained including fitting fixed on wall/ceiling and connecting of complete with 3 core flexible cable of size 23/0.0076 complete all as specified and directed.

Supply and Fix 20W High efficient LED Security light fitting with pressure die cast LM6 Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie is 100lm/W with IP 65 specification complete all as specified and directed.

Supply and fix 10W LED bollard, pressure die cast powder coated housing with PC diffuser, efficient high output LED with IP 66 protection, fixing on concrete bed of size 1'x1'x1' complete all as specified and as directed.

Supply and fix 150W LED post top energy saving enviromental friendly long life aesthetically designed with symmetrical light distribution span aluminium landscape luminiare with higher powe LED and better uniformity incl provision of GI pipe of suitable size, MCB SP 10A housing in sintex box and fixing on place complete all as specified and directed.

Supply and fixing of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps, 240V complete all as specified and directed.

Supply and laying inreplacement of sub main wiring with Two single core PVC insulated FRLS cable with copper conductor multistranded 1100 volts grade 2.5 sqmm in and including non-metallic rigid PVC Conduit and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 2.5 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly and including taking down of old unserviceable sub main wiring complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length complete all as specified and directed.

Supply and laying inreplacement of sub main wiring with Two single core PVC insulated FRLS cable with copper conductor multistranded 1100 volts grade 4.0 sqmm in and including non-metallic rigid PVC Conduit and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 4.0 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly and including taking down of old unserviceable sub main wiring complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length.

Supply and fix sub main wiring with Two single core PVC insulated FRLS cable with copper conductor multistranded 1100 volts grade 6 sqmm in and including non-metallic rigid PVC conduit and accessories and fixing arrangements fixed to surface on wall, floor or ceiling etc including 6 sqmm PVC insulated FRLS multistranded copper earth continuity conductor and connecting to main earth dolly and including taking down of old unserviceable sub main wiring complete all as specified and directed. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length.

Supply & fixing of sheet metal enclosure MCB DB double door type 230v with suitable bus bar model all as specified and directed incl taking down old u/s DB for (a) SPN 12 ways complete all as specified and directed.

All as per item No.165 above but SPN 8 ways

All as per item No.165 above but SPN 6 ways

Supply and fixing of MCB SPN 63A, upto rupturing capacity of 10KA, C curve type incl taking down old u/s MCB SPN complete all as specified and directed.

Supply and fixing of MCB capacity SPN 40 A 10 KA incl taking down old u/s MCB SPN complete all as specified and directed.

Supply and fixing of MCB capacity SPN 32 A 10 KA incl taking down old u/s MCB SPN complete all as specified and directed.

Supply and fixing of MCB capacity SPN 25 A 10 KA incl taking down old u/s MCB SPN complete all as specified and directed.

Supply and fixing of MCB capacity SPN 10 A 10 KA incl taking down old u/s MCB SPN complete all as specified and directed.

Supply and fixing of MCB SP 06 to 32A, upto rupturing capacity of 10KA, C curve type fixed in PVC Cable loop box incl taking down old u/s MCB SP complete all as specified and directed.

Material and labour for Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground ( earth pit not less than 2.25mtrs deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised ironr steel all as shown in electrical plate No.5 connected to earthing test point incl PCC earth pit chamber of size as mentioned in SSR Part I all as specified or indiacted including testing on completion and putting indication plate by entering the earth resistance value on it with black paint on white background complete all as specified and directed.

Material and labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for earthing etc. as required 4mm dia galvanised iron wire complete all as specified and as directed

M&L for taking down carefully ceiling fan of any make, size, capacity from its position, dismantling complete fan, examine complete parts thoroughly, oiling, greasing on all parts and complete overhauling of fan including replacement of small parts such as split pin, nuts, bolts, screws and reassembling complete fan and make fully functional, re-fixing the fan in position including replacement of three core copper wire of suitable size from fan motor to ceiling rose complete all as directed by Engr-in-Charge. Note :- (i) Quoted rate is deemed to be inclusive of over hauling, rehanging & testing complete. (ii) Fan bearing, rewinding and capacitors, if essential to be changed will be measured and paid seperately).

M&L for Rewinding of ceiling fan motor of any type, any size,and make with approved quality of super enamelled copper wire as per original gauge and size including varnishing heating etc complete all as specified and directed.

Supply and fix in repair of capacitor 2.15/ 2.5 micro Farad, 240 Volt, two wired and ISI marked complete all as specified and directed.

Supply and fix in repair of ball bearing of No 6201 complete all as specified and directed.

M&L for spray painting to exposed surfaces of ceiling/exhaust fan/ Air Circulator any size with two coats of synthetic enamel paint (as per existing colour) over a coat of red oxide primer by spray gun , including preparation of old painted surface by scrapping or complete removal of old paint, filling cavities with zealer and writting MES Nos with black enemel paint complete all as specified and directed.

Supply and fix in repair of iron down rod/connecting rod of ceiling fan of size upto 600 mm with new nuts, bolts and safety pins complete all as specified and directed.

Supply and fix in repair of iron down rod/connecting rod of ceiling fan of size upto 1200 mm with new nuts, bolts and safety pins complete all as specified and directed.

S&F in repair of fan blade assembly 1200 mm sweep pearl white complete all as specified and Directed.

Supply and fixing of Name board of Glass frame of particular instrument fitted in installation duly mentioning the details of instrument as per PRB/MH Sheet and size of the board 1.5x1.0x0.03mtr complete all as specified and directed by Engr-in-Charge (Note : The letters are to be in Black colour in white background and font size complete all as specified and directed.

M&L for taking down carefully Air circulating fan fan of any make of size 750 mm sweep from its position, dismantling complete air circulating fan, examine complete parts thoroughly, oiling, greasing on all parts and complete overhauling of fan including replacement of small parts such as split pin, nuts, bolts, screws and reassembling complete air circulating fan and make fully functional, re-fixing the fan in position including replacement of three core copper wire of suitable size from switch box to ceiling rose complete all as directed by Engr-in-Charge. Note :- (i) Quoted rate is deemed to be inclusive of over hauling, rehanging & testing complete. (ii) Fan bearing, rewinding ,Gaurd set,Blade,Connecting rod,outer cover ,capacitors etc , if essential to be changed will be measured and paid seperately). (iii) Contractor will arrange ladder/tools for hanging and taking of air circulator fan from site at approx 6 mtr and rate to be deemded in quotated rates.

M&L for Rewinding of Air circulators fan motor of 750 mm sweep heavy duty with approved quality of super enamelled copper wire as per original gauge and size including varnishing heating etc complete all as specified and directed.

Supply and fix in repair of capacitor 8 micro Farad ,240 volts, two wired and ISI marked complete all as specified and directed.

Supply and fix in repair of ball bearing of No 6203 complete all as specified and directed.

Supply and fix in repair of fan blade made out of steel suitable for wall mounted air circulator fan of 750 mm sweep complete all as specified and directed.

S&F in repair of Guard set with ornament Supreme plus steel Grey 750 mm sweep suitable for wall mounting air ciculator fan complete all as specified and directed.

S&F in repair of switch box cover supreme plus steel grey 450,600 & 750mm sweep air circulator fan complete all as specified and directed.

M&L for taking down carefully Exhaust fan of any make, of size upto 300/450 mm sweep from its position, dismantling complete exhaust fan, examine complete parts thoroughly, oiling, greasing on all parts and complete overhauling of exhaust fan including replacement of small parts such as split pin, nuts, bolts, screws and reassembling complete fan and make fully functional, re-fixing the exhaust fan in position including replacement of three core copper wire of suitable size from exhaust fan motor to ceiling rose complete all as specified and directed. Note :- (i) Quoted rate is deemed to be inclusive of over hauling, rehanging & testing complete. (ii) Fan bearing, rewinding and capacitors, if essential to be changed will be measured and paid seperately). (iii) Contractor will arrange ladder/tools for fixing and taking of exhaust fan from site at approx 10 mtr and rate to be deemded in quotated rates.

M&L for Rewinding of Exhaust fan of size upto 300 mm motor of any type, any size,and make with approved quality of super enamelled copper wire as per original gauge and size including varnishing heating etc complete all as specified and directed.

All as per item No.193 above but 450mm

Supply and fixing of Exhaust fan louvers of any size to be fixed in re-placement taking down from any height of building complete all as specified and directed.

Supply and fix in repair of capacitor 3.15/4 micro Farad ,240 volts, two wired and ISI marked complete all as specified and directed.

Supply and fix in repair of ball bearing of No 6202, complete for exhaust fan of size 300mm complete all as specified and directed.

Supply and fix in repair of ball bearing of No 6203 complete for exhaust fan of size 450mm complete all as specified and directed.

S&F in repair of blade assembly of metal exhaust fan upto 300 mm sweep grey colour complete all as specified and Directed.

Supply and fix in repair of fan blade made out of steel suitable for wall mounted air circulator fan upto 450 mm sweep complete all as specified and directed.

KRISHNA CONSTRUCTION COMPANY

M/S SOLANKI GENERAL SUPPLIERS

M/S HARIOM CONSTRUCTION COMPANY

M/S SIDHU CONSTRUCTION COMPANY

Aggarwal brothers and company