CA NO GE(N)AMB-26/2022-23 REPAIR TO JOINERY, PLUMBING, SANITARY, PLASTERING AND OTHER CONNECTED BUILDING REPAIR WORK IN OTM-VIII ACCN AREA OF AGE B/R-I (NORTH) UNDER GE (N) AMBALA CANTT

Amount

M & L PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

M & L plain cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in mud stops, bed blocks, lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork for rough finished surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L brick work with sub class 'B' old size bricks using old servicable bricks including cleaning of old bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290 (Gde E-165) complete all as specified and as directed by the Engineer-in-Charge.

S&F powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Material and labour for repairing of all type aluminium window/door shutter with frame and refixing it after resecuring its frame work by means of tightening with new screw or by new frame ,cleats, rubber gasket and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge. Note:- New frame shall be measured and paid for separately.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Supply and fixing galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down rolling shutter push pull or manual type incl taking down accessories like shaft, top cover, guide channel and straightening/ rectify warped/buckled parts, with and including cleaning/overhauling, greasing/oiling, make functional rolling shutter in all respect and refixing the same in same opening to walls/RCC members all as directed by the Engineer-in-Charge.

Replacement of existing unserviceable mild steel wheel gear box with new wheel gear box of suitable for large size shutters having area more then 8 sqm including handle as per existing size complete all as specified and as directed by the Engr-in-charge.

Taking down chowkats or frames area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engr-in-charge.

Taking down chowkats or frames area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engr-in-charge.

Taking down shutters of any description area not exc 1.00 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelam sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 12 mm thick prelaminated particale board,interior grade, prelaminated both side with decorative choice lamination and fixed to aluminium door with glazing clips, rubber gasket etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 150mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing stainless steel butt hinges 100mm long medium weight complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed by the Engineer-in-Charge.

S & F Continuous (piano) hinges, width of flaps 30mm mild steel, bright finish or electro galvanised complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm long fancy type stainless steel handle complete all as specified and as directed by the Engineer-in-Charge.

S&F magnet catcher fixed in cabinet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed by the Engineer-in-Charge.

S&F aluminium (Diecast) body hydraulically door closer regulated,designation No.3, universal type,suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg complete all as specified and as directed by the Engr-in-charge.

Supply and fix 100 mm size mild steel mortice lock, vertical type, 2 levers with duplicate key complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing mild steel helical door spring, 200 mm long, fixed to wooden chowkats or welded to angle iron/ steel door frames complete all as specified and as directed.

Supply and fixing as in repair, mild steel helical door spring, 200 mm long, fixed to wooden chowkats or welded to angle iron/ steel door frames complete all as specified and as directed.

Supply and fixing as in repair stainless steel, powder coated, curtain rod 25mm dia having wall thickness 1.00 mm fixed with and including decorative stainless steel brackets ,holding and funnel at the end, etc. complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick walls, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick wall ,pinning in making good to facing where required and pointing in CM 1:3 to ends or edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting exceeding 10 cm but not exceeding 20 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair, bib tap , cast copper alloy, with crutch or butterfly handles screwed down, screwed for iron pipe or for brass ferrule suitable for 15mm bore pipe or union, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body and capstan head screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing fancy type pillar tap of 15mm bore, cast copper alloy, with capstan head, chromium plated, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair, 15mm bore cast copper alloy chromium plated stop valves screwed down, high pressure with crutch or butterfly handle, scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing fancy type 15mm bore cast copper alloy chromium plated angular stop valves, screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connection, flush pipes, etc. for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe and complete accessories as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing plastic water closet seat cover, white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixed as in repair fancy type, shower rose 125mm size , brass Chromium plated, revolving type, fixed to existing steel pipe or union 15mm bore complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair, brass chromium plated wall/sink mixer for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair brass chromium plated toilet paper holder complete fixed to wall complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 450 mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair chromium plated,Health Faucet telephonic with wall hook type with CP flexible arm and chromium plated jet sprayer complete all as specified and as directed by the Engineer-in-Charge.

S & F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen with plugs, waste pipe, brass chromium plated coupling including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge

S&F 32/40mm dia PVC waste pipe of standard length for wash hand basin / Kitchen sink etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixed as in repair, PVC cabinet box type with looking mirror of size 450mm x 600mm complete all as specified and directed.

Supply and fixing brass chormium plated towel rack of size 600 mm x 250mm with lower hanger including brackets, fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china, counter top, white wash hand basin white, of size 510mm x400mm x180mm fixed and including, 32mm dia brass chromium plated waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe) but including brass chromium plated spreader, PVC waste pipe , providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) as iin repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair , vitreous chainaware, white, urinal partition of size 310 x 700 mm fixed to wall with plugs and chromium plated screws, terminating about 40cm above floor level complete, all as specified and as directed by the Engineer-in-Charge.

M&L cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity 250 litre and upto and including 500 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc .

M&L cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity exceeding 500 litre and upto and including 1000 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc .

S & F as in repair PVC tank lid/cover suitable for capacity 250 ltr and upto and including 500 ltrs with and including locking arrangments such as nuts, bolts etc complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair PVC tank lid/cover suitable for capacity exceeding 500 ltr and upto and including 1000 ltrs with and including locking arrangments such as nuts, bolts etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) tripple layer body, 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight-210 grm) complete all as specified and as directed by the Engineer-in-Charge. Note : Water storage tank shall be White in colour.

Supply and fixing as in repair 500 litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight-210 grm) complete all as specified and as directed by the Engineer-in-Charge Note:- Tank shall be in white colour.

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by the Engineer-in-Charge.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt over and including a coat bitumious primer @ 0.40 ltr /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temprature and viscosity 70-160 cps with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc after preparing the surface complete as per standred practice as per manufacture's instructions . The vital physical and chemical parameters of the membrane shall be under ;- (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d-5147) (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only complete all as specified and as directed by the Engineer-in-Charge. (iv) The work shall be carriout at a height upto 12 metre.

M & L roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, and applying neat cement slurry @3 Kg/Sqm complete all as specified and as directed by the Engineer-in-Charge.

M & L providing PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in roof kerb, mud stps rounded or chamfered on edges complete all as specified and as directed by the Engineer-in-Charge.

M & L providing PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in padding over RCC roof including form work where ever required complete all as specified and as directed by the Engineer-in-Charge.

M & L cement concrete tiles 25 cm x 25cm x 20 mm thick, machine pressed laid on screed bed and joints grouted flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M & L applying a coat of solar reflective aluminium paint @ 0.11 kg per sqm on APP membrane surfaces complete all as specified and as directed by the Engineer-in-Charge.

M & L cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets and false ceiling frame work complete all as specified and as directed by the Engineer-in-Charge.

S & F GI Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint complete for all heights as per specifications including 4mm thick HPSC pre-prime non asbestros fiber cement building board (E-classic or equivalent) decorateive finish fixed to frame work with holding down clips in false ceiling complete all as specified and as directed

S & F 5mm PVC hollow sheet (the thicknees of wall 0.7 to 1.00mm) panelling inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified including dismantling of existing paneling.

Material and labour 12 mm thick prelaminated particle board exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet , shelves for cupboard, frame with door if required including 3mm thick 2nd class hardwood leeping patti on cut edge of boards as in repair complete all as specified and as directed by the Engineer-in-Charge.

Material and labour 18 mm thick prelaminated particle board exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet , shelves for cupboard, frame with door if required including 3mm thick 2nd class hardwood leeping patti on cut edge of boards as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 5 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement but using water proofing compound @ 2% by weight of cement as per manufacturer's instructions complete all as specified and as directed by the Engineer-in-Charge. (water proofing compound shall be measured and paid for separatally)

Supply only water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

Taking down loose plaster from ceiling of slab, edges and soffit of chajjas and the like, cleaning surface with wire brush to remove all dust/dirt/loose particles to expose old steel reinforcement, applying neat cement slurry@ 3Kg per sqm and applying dubbing out 20mm thick in PCC 1:2:4 type B-0 or cement mortar 1:3 and finishing the exposed surface with 5mm thick plaster in cement mortar 1:3, finishing even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. .

M&L rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

M&L preparing new plastered surfaces and applying two coats of oil bound distemper with painting roller over a coat of alkali resistant primer complete all as specified and as directed by the Engineer-in-Charge.

M&L applying 2 to 3 mm thick wall care putty white cement based in two or more coats to achive smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of new plastered/ unplastered surfaces of brick/concrete ceiling and applying three coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of newly plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of colour lime wash over prepared surfaces of wall, pillar, cornices complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash over prepared surfaces of ceiling, pillar, cornices complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of colour lime wash over prepared surfaces of wall, pillar, cornices complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper with painting roller over prepared surfaces of the walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old wooden surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old wooden surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc., filling all holes and cracks with white cement based wall care putty and applying one coat of cement base paint complete, all as specified and as directed by the Engineer-in-Charge.

M&L preparation of old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc., filling all holes and cracks with white cement based wall care putty and applying two coats of cement base paint complete, all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls, pillars, cornices etc. and applying two coats of plastic emulsion paint with painting roller over and including 1 to 2 mm thick wall care putty white cement based in two or more coats to achive smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls, pillars, cornices etc. and applying one coat of exterior acrylic emulsion paint with painting roller over prepared surfaces, complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls and applying two coats of exterior acrylic emulsion paint with painting roller over prepared surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of 100/75 mm cast iron or reinforced concrete drain pipes or PVC pipe any dia, set in cement mortar including taking out of trenches, if required complete all as specified and as directed by the Engineer-in-Charge.

M & L 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and directed. (Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall confirm be to IS 5382-1985)

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 4.8 mm thick tinted glass to aluminium door with glazing clips, rubber gasket etc complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge

Material and labour Non-skid ceramic coloured tiles joint free 1st quality (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L Non Skid coloured ceramic tiles premium/1st quality of same description as of floor tiles in serial item No 133 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour vitrified ceramic light shade tiles premium/1st quality 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour vitrified ceramic light shade tiles premium/1st quality 10mm thick of same description as of floor tiles as in serial item No 135 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour vitrified ceramic light shade tiles premium/1st quality 10mm thick (square/rectangular) area of each tile exceeding 0.42 sqm and not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour vitrified ceramic light shade tiles premium/1st quality 10mm thick of same description as of floor tiles as in serial item No 137 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L 25mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base, finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour glazed ceramic coloured tiles joint free 1st quality in vertical surfaces/ skirtings/dados of size 450x300x7mm thick or nearest size as required , set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L machine cut kota stone slab flooring 16 to 18 mm thick of size not less than 550mm x 550mm in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M &L 10mm thick coloured paver tiles (Endura Tiles) of size 300 x 300mm in floors etc set and jointed in neat cment slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in C.M 1 :4 ,complete all as specified and as directed by the Engineer-in-Charge.

M & L providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair helical wire spring 8 gauge complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick walls, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting exc 20 cm girth complete all as specified and as directed by the Engineer-in-Charge.

S & F 2mm thick fibre glass reinforced translucent plain sheeting with minimum 10 cm side lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed by the Engineer-in-Charge.

S & F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm aluminium mortice lock, vertical type, two lever with dublicate key complete all as specified and as directed by the Engineer-in-Charge.

S&F 200 mm long disk type aluminium handle complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long peg stay of aluminium and fixed to aluminium window complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair, 20mm bore cast copper alloy chromium plated stop valves screwed down, high pressure with crutch or butterfly handle, scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair 20 mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and as directed by the Engineer-in-Charge.

M&L 6mm thick asbestos cement, corrugated or semi- corrugated in roofs,walls etc fixed with L type or J type or cranked hook bolts complete all as specified and as directed by Engr-in -charge.

M&L asbestos cement, one piece plain angular ridge 6mm thick fixed with L type or J type or cranked hook bolts in roofs/walls complete all as specified and as directed by Engr-in -charge.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 grams per Sqm (Az 150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150grams/Sqm (Az-150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wooden scantling 40 sqcm and over in section in framed work in position complete all as specified and as directed by the Engineer-in-Charge.

S & F rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe-410-W (Grade E-250) quality B complete all as specified and as directed by the Engineer-in-Charge

S&F as in repair stainless steel kitchen plate rack made from 1mm thick sheet of size 600mm x 600mm x 250mm and having weight not less than 5.00 Kg each and fixed with rawl plug and steel screws complete all as specified and as directed by the Engineer-in-Charge.

MAYANK ENTERPRISES

M/s B.S.Jain

shiv const co

M/S SHANTI CONSTRUCTION

m/s parmod kamar

Durga Enterprises

dhingra builders