Repairs to pot holes resurfacing and painting to roads in Allenby lines under GE South Ambala Cantt

Amount

Material and labour for scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exceeding 400 sq m, exceeding 50 mm and not exceeding 100mm deep complete all as specified and directed.

Material and labour for preparation of black top bituminous macadam surface by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with air compressor to remove all loose dirt etc and applying evenly a bituminous tack coat of gradeVG-10 @ of 3 Kg per 10 sqm complete all as specified and as directed.

Material and labour for preparation of black top bituminous macadam surface by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with air compressor to remove all loose dirt etc and applying evenly a bituminous tack coat of GRADE VG-10 @ of 5 Kg per 10 sqm complete all as specified and as directed.

Material and labour for 75mm thick or less (consolidated thickness) premixed, bituminous macadam (with crushed and graded stone) with 4% binder content by weight of total mix, rolled and compacted to required camber and gradient with paving bitumen of grade VG-30 grade using mechanical paver and rolling with 8 to 10 tonne power roller/ tandem vibrating roller etc complete all as specified and directed.

Material and labour for repair to pot holes of any depth not exceeding 1.00 Sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads/path etc cutting around edges to at least 25mm and more as per site requirement in depth and making good by applying tack coat of paving bitumen @ of 5 Kg per 10 Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 Kg per 10 Sqm, blinded with 0.09 cum of stone chippings 6.3mm size and again well rammed (including supply of premixed macadam binder and chipping) depth of pot holes exceeding 30mm complete all as specified and directed.

Material and labour for laying bituminous premix semi dense asphaltic concrete 30mm (consolidated thickness) using with 5.5% of binder (grade VG-30) content by weight of total mix, rolled and compacted to required camber and gradient using mechanical paver and rolled with 10-12 tonne capacity vibratory road roller rolled to uniform smooth surface ,complete all as specified and as directed.

Material and labour for preparation of new road surface and applying 2mm thick retro-reflective thermo plastic road marking paint with glass beads, exceeding 10cm width or girth, hot applied on road surface mechanically conforming to BS-3262 and according to the specification laid down by IRC and MOST (Ministry of surface transport) specification 803 Vol -III.complete all as specified and directed.

Supply and fixing (in repairs), cat eye, dual (62 beads minimum), aluminium casted body, of size 100mm x 100mm x18.5mm, having ABS plastic strip containing 62 mini retro reflective glass beads of colour white/red/yellow on both sides (minimum 31 beads on each sides) and fixed complete with steel zinc plated nails/stud of dia 12mm and of length 120mm complete all as specified and directed . Note:- (i) Fixing arrangement shall be as per manufacturer's instructions. (ii) Designed to bear 25 Tonnes load and having impact strength of 253 KN.

Supply and fix in repairs 'Solar Road stud 125x125x25 mm. Solar Road stud made from Aluminium alloy ,Solar powered by monocrystal solar pannel with following specification. (i) Battery Type-. One high capacity Ni-Cd rechargeable battery. (ii)View distance of solar stud shall not be less than 1000 mtrs. (iii) LEDs shall be 10mm, 3 pieces each side and total 6 pieces for high brightness of different colours (iv) Back up time shall not be less 12 hours of continous lighting at night. (v) Designed to bear 25 Tonnes load and having impact strength of 253 KN. Note-Colour shall be decided by Engineer-in-Charge/GE.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) for including removal the rubbish/ demolished material outside defence land, complete all as specified.

Material and labour for laying sand over PCC for cushioning of paver blocks, complete all as specified and as directed.

Supply and fixing vibratory compacted precast concrete coloured(using red colour pgment ), rubber moulded , interlocking designer paver blocks, confirming to IS-15658-2006 of 60mm thickness, M-35 grade in path, hard standing, etc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified and as directed.

Material and labour for providing factory made Precast Cement Concrete kerb stone, 1:2:4 type B1 (using 20mm graded aggregate) with plain fair faces, including chamfers, weatherings, throating etc. and set in CM 1:4, complete all as specified and as directed. Note:- The minimum size of kerb stone shall be 300mm x 300mm x 100mm and shall be embedded in the ground average 10cm deep. The quoted rates includes embedding kerb stone and temping ground around kerb stone removal of surplus soil, etc.

Material and labour for preparation of new or previous untreated concrete or plastered surfaces of any description and grith not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a priming plaster coat complete all as specified and as directed.

Supply and fixing road side sign boards consisting of frame and posts of 75mm dia stainless steel pipe of Grade-304 (size of rectangle frame for writing letters is 1.00m x 0.75m), including 5mm thick MS plain black sheet painted with two coats of synthetic enamel paint of green colour over one coat red oxide primer and welded to SS frame for writing names, including writing letters of size 0.15m x 0.10m each using retroreflective tape of white colour on both bsides of MS plates, height of frame with MS pl;ate is 1.00m above GL, including excavation of post holes in soil of size 0.50m x 0.50m and embedding of vertical posts in and including PCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregate complete all as specified and as directed.

Supply and fixing road convex mirror of dia 60cm, fitted in orange colour cap body of ABS with glass mirror made up of unbreakable poly-carbonate, including MS pipe vertical post with stainless steel brackets, including excavation of post holes in soil of size 0.50m x 0.50m and embedding of vertical posts in and including PCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregate complete all as specified and as directed.

Supply and fixing speed bumps made up of polyethylene plastic of size 495mm x 420mm x 70mm each (black and yellow colour pattern interlocked alternately), UV stabilized, studded with reflectors on both sides, interlocking type, including drilling 4 Nos holes to road surface and fixing with lag bolts with anchor and washers,complete all as specified and as directed. Make: Dark Eye or equivalent as approved by GE Note:- (i) Fixing arrangement shall be as per manufacturer instructions. (ii) Designed to bear 25 tonnes lo0ad and having impact strength of 253 KN.

Note:- Amount of credit of Rs. 8,000.00 for retrieved materials is mentioned in Schedule of Credit Page Nos. 58 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Bal Singh and Sons

M/s VARINDER PAL SINGH AND CO