Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹35.8 LAccepted-AOC | L1 | Accepted-AOC Bid Rank-L1 | |
| 2 | L2₹36.7 L+₹93,799.20 (2.62%)Rejected-AOC HIMACHAL PRADESH HP | KULLU | HIMACHAL PRADESH | 172023 | L2 | Rejected-AOC Bid Rank-L2 |
Tender Value
₹43.7 L
EMD Value
₹88,000
Closing Date
6 Mar 2023, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
O/o EE Bhawarna Division HPPWD Bhawarna
O/o EE Bhawarna Division HPPWD Bhawarna
Balance work of Ground Floor.
2023_PWD_69627_1
NIT No.19107-66 DT.21-02-2023-Bhawarna
Open Tender
Civil Works - Buildings
Item Rate
180 days
Bhawarna
Please refer Tender documents.
12 documents required · 12 mandatory
₹2,000
₹88,000
6 May 2023
25 Feb 2023
6 Mar 2023
25 Feb 2023
6 Mar 2023
25 Feb 2023
Amount
Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavation earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-in-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate inclusive royalty, malkana, toll tax, GST and other taxes imposed by the government.
Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation,. Footings bases of columns and mass concrete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plain in all floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etc. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying cement concrete 1:4:8 (One Cement isto Four Sand isto eight) graded stone aggregate 40mm (Forty millimetre) nominal size for haunching of pipes of the 150 mm ( One hundred fifty millimetre) internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.
Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) and minimum cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding cost of form work and reinforcement for reinforced concrete work in coulmn, pillers posts and struts upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (20 newton per square millimeter) and minimum cement content not less than 320 kg/cubic meter and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their supports balconies, beams, girder, bressumers and cantiliver upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) and minimum cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm square with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete in reinforced concrete Chhajjas for all thickness in up to floor two levels up to all heights including finishing the exposed surface with cement mortar 1:3 (One cement isto Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work . The rates are inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge.Rate is inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (twenty newton per square millimetre) and minimum cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design including cost of form work steel but excluding cost of reinforcement for reinforced concrete work in moulding as in cornies, window sills etcetra not exceeding 15cm in girth upto all floor levels. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying tor steel of TISCO, SAIL reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per approved drawing, design, and specification in all floor levels including the cost of binding wire and cost of dewatering if arrisen during placement of reinforcement as per PWD specification and approved, drawing design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Filling with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm (Twenty centimetre) in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m (Fifty metre) and lift upto 1.5 m (One decimal five metre) complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax , sales tax or other taxes imposed by the government..
Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate inclusive royalty, malkana, toll tax, GST and any other taxes imposed by the government.
Stone filling tightly dry hand packed under flooring including ramming and consolidation complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax , sales tax or other taxes imposed by the government.
Providing and laying plain cement concrete 1:2:4 (One cement isto two sand isto four graded crushed stone aggregate 40mm (Forty millimetre) nominal size & curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing and design including entire carriage of material with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of octroi, Royality, Malkana, sale tax, toll tax, GST and any other taxes imposed by the government.
Second class brick work using common burnt clay building bricks in cement mortar 1:6 (one cement isto six sand) in super structure upto all floor lavels as per PWD specification drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Second class half brick work using common burnt clay building bricks with hoop iron in cement mortar 1:4 (one cement isto four sand) in super structure as per PWD specification, drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and fixing M.S. channels for doors, windows, frames manufactured from M.S. section 40mmx75mmx4mm (Forty millimetre into seventy five millimetre into four millimetre) with M.S. flat 75x4mm (Seventy five into four millimetre) in combination as per drawing and design including hinges, jamb, lock jamb beed and if required thrashold including thrashold of M.S. angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm (Two decimal five millimetre) thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of the surface complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.
Providing and fixing factory made P.V.C. door frame of size 50x47 mm (Fifty into forty seven millimetre) with a wall thickness of 5 mm (Five millimetre), made out of extruded 5mm (Five millimetre) rigid PVC foam sheet, mitred at corners and joined with 2 Nos (Two Numbers) of 150 mm (One hundred fifty millimetre) long brackets of 15x15 mm (Fifteen into fifteen millimetre) M.S. square tube, the vertical door frame profiles to be reinforced with 19x19mm (Nineteen into nineteen millimetre) M.S. square tube of 19 (Nineteen) gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm (Sixty five/ Hundred millimetre) size complete, as required at site as per H.P.P.W.D. specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rate is including octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government
15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetewrs) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
6mm (six millimeter) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and laying Kota stone slab 20 mm (Twenty millimetre) thick Single slab flooring of approved shade over 20mm (Twenty millimetre) average thick base of cement mortar 1:4 (One cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Kota stone slab 20 mm (Twenty millimetre) thick in Single slab with round noising for treads and riser of stairs approved shade 12mm (Twelve millimetre) average thick base of cement mortar 1:4 (One cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and Fixing stainless steel knock down railing of kich AISI 316 of 35mm (Thirty five millimetre) Dia handrail fixed on S.S flat baluster ( Design code DT-53-2 - 163 ) placed at 1200mm (Twelve hundred millimetre) centre to centre along with 3 (Three) Numbers @ 16mm (Sixteen millimetre) mid rail connected at the side of baluster with fixture. The baluster would be fixed on to floor with casted base plate of minimum 6mm (Six millimetre) thickness. Base plate shall be concealed with suitable S.S 316 grade cover cape. Railing height to be taken 85 mm (Eighty five centimetre) from floor level complete in all as per specifications, approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.
Providing and fixing Factory made 35mm (Thirty five millimetre) thick both side commercial phenol bonded of (Century/ Alpro/ Duroply) ISI marked IS No.-2202 flush door shutter interior grade core of block board construction with Ist class frame of hard wood and well matched 1st class Indian Teak ply veneering with vertical grains or cross bands and face veneer on both faces of flush door as per approved specifications including black enamelled M.S. butt hinges with necessary screws including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.
Providing and fixing factory made double steel shutter side hungs (one glazed and one wire gauge) for steel windows side hung (one glazed and other wire gauged) of standard rolled steel sections, jointing mitered welded with manufactured to relevant ISI standard specification with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with special putty of glazed side of shutter and wire gauge of IS designation 85G with metal beading on other side complete including priming coat of red lead paint. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.
Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded with 16x3.15mm(Sixteen into three decimal fifteen milimetres) lugs 10cm (Ten centimetres) long with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with glazing clips and special metal sash putty of approved make complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Fixed steel windows
Top hung Ventilators
Providing and fixing M.S. plain grills 10x10mm (Ten into ten millimetre) square bar in combination of 20x4mm (Twenty into four millimetre) M.S. flat as per design required pattern in wooden frames of windows etc. with M.S. round headed bolts and nuts or by screws. The rate is inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.
Providing and fixing 300x16mm (Three hundred into sixteen millimeter) size coloured / anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and fixing coloured anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
250x10mm (Two hundred fifty into ten millimetre) size
150x10mm (Onw hundred fifty into ten millimetre) size
Providing and fixing 150mm (one hundred fifty millimetre) size coloured / anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and fixing 100mm (One hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etcetra to suit shutter thickness complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.
Providing and fixing 150 mm (one hundred fifty millimetre) matt finished Aluminium hard drawn hooks and eyes complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax toll tax, GST and any other taxes imposed by the government.
Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters and sand papered smooth to give final matt finish to the surface complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.
Finishing wall with Apex weather proof exterior emulsion of Asian paint/ Nerolak Suraksha paint/ Berger paint/Dulux paint of approved brand and manufacture and of required shade on undecorated wall surfaces (Two or more coats) to give an even shade after thoroughly brushing the surface to remove all dirt, dust and remains of loose powdered material including cost and carriage of material with in all leads, lifts and other incidentals as per specificatins, approved drawing as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.
Wall painting interior emulsion paint of Asian paint / Nerolac Suraksha Paint/ Berger paint / Dulux paint of approved shade for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty required for matting the surface and cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.
Wall painting (two coats) with premium emulsion paint of Asian paint / Nerolac Suraksha paint/ Berger paint / Dulux paint approved shade on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface including cost and carriage of materials with in all leads, lifts and other incidentals as per specifications, approved drawing, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.
Wall painting (two coats) with acrylic emulsion paint of Asian paint / Nerolac Suraksha Paint/ Berger paint / Dulux paint of approved shade for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty required for matting the surface including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.
Distempering (two or more coats) with dry distemper of Berger/Nerolac/Asian Paint and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings & other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer as PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.
Painting two coats(excluding priming costs) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Applying a priming coat over new wood and wood bases surfaces after and including preparing the surface by thoroughly cleaning, oil, grease, dirt and other foreign matter, sand papering and knotting with ready mixed paints brushing wood primer pink as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.
Providing and fixing 1800x1200mm (One thousand eight hundred into one thousand two hundred millimetre) green chalk board/Black board shall be made of steel of thikness 0.3 to 0.4 mm (zero decimal three to zero decimal four millimetre) It shall have vitreous Enmal coating of 0.095 mm (zero decimal zero nine five millimetre) minimum thickness on top and 0.3 mm (zero decimal three) on the back. top shall be free from waviness and shall show excellient ability. The core material shall be 9mm (Nine millimetre) thik MDF board heaving bluk density of 750kg/cum (Seven hundred fifty kilogram per cubic metre) and grade-1 as per IS : 212406-203 edition 2.2 the backing material sheet shall be min. 0.25mm (zero decimal two five millimetre) thick electro galvanised steel sheet conforming to is: 277-2003. The board shall be fixed on the wall with specially designed J clamps and Sq. clamps with help of Nylon sleves and screws as per site requirement the Government.
mukesh
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .