REPAIR/REPLACEMENT OF FLOORING, FOOTPATH, HARD STANDING, JOINERY, SANITARY AND WATER SUPPLY WORK AT OFFICE COMPLEX AND UNIT COMPLEX AND CERTAIN PLACES UNDER DGNP(V)

Amount

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness and removing rubbish off from the premises of MD land, complete all as specified and directed.

Material & labour for 75 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded crushed stone aggregate), as in sub base of floors, complete all as specified and directed.

Material & labour for colour chequered cement concrete tiles of size 30cmx30cmx25 mm thick, in floors jointed with grey cement and pigments with and including 20 mm thick screed bed or bedding layer of mortar (1:6) for laying floor finishes, complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Material & labour for precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar complete 1:6, complete all as specified and directed.

Dismantling of floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off from the premises of MD land, complete all as specified and directed.

Material & labour for dark coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match the shade of tile, over with and including 20 mm thick screed bed or bedding layer of mortar (1:6) for laying floor finishes, complete all as specified and directed.

Material & labour for coloured glazed ceramic tile in vertical surfaces 300 x 600 x 7 to 9mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile with and including 10mm thick rendering as backing coat in cement mortar (1:4) for receiving of tiles complete all as specified.

Material & labour for dark coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match the shade of tile, over with and including 20 mm thick screed bed or bedding layer of mortar (1:6) for laying floor finishes, complete all as specified and directed.

Material & labour for granite (of any type) tiles 18 to 20 mm thick machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, with and including 10mm thick rendering as backing coat in cement mortar (1:4) for receiving of tiles complete all as specified.

Material & labour for granite (of any type) tiles 18 to 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over with and including 20 mm thick screed bed or bedding layer of mortar (1:6) for laying floor finishes, complete all as specified and directed.

Supply and fixing in repairs aluminium, anodized, barrel tower bolts of extruded section 100 mm long, complete all as specified and directed.

Supply and fixing in repairs aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

Supply and fixing in repairs Butt hinges medium weight, cold rolled mild steel 100mm size fixed with necessary screw or welding as required complete all as specified and directed .

Supply and fixing in repairs butt hinges medium weight, cold rolled mild steel 75mm size fixed with necessary screw or welding as required, complete all as specified and directed.

Supply and fixing in repairs 150mm overall length of cover plate Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

Supply and fixing in repairs aluminium door closer (Die cast body) for Aluminium door size 6000x 1100mm environment conditions accessibility to closer arm space limitations on the top rail of door closer position, complete all as specified and directed.

Supply and fixing in repairs Aluminium, anodized, hasp and staple safety type 125 mm size, complete all as specified and directed.

Supply and fixing in repairs aluminium , barrel tower bolts 200 mm long, complete all as specified and directed.

Supply and fixing in repairs aluminium handle, cast type, anodised, 150mm size, complete all as specified and directed.

Supply and fixing in repairs galvanised aluminium wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Supply and fixing in repairs sheet glass 3 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Supply and fixing in repairs figured glass 3 mm thick pin head type and glazing with oil putty in squares n. exc 0.5 sqm in each pane, complete all as specified and directed.

Supply and fixing in repairs 150 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate, complete all as specified and directed.

Supply and fixing in repairs 25 mm dia mild steel PVC coating designer drapery/ curtain rod, complete all as specified and directed.

Supply and fixing in repairs mild steel PVC coating bracket/ holder for drapery rod fixed with screws , complete all as specified and directed. (Design and colour approved by GE)

Supply and fixing in repairs 2nd class hard wood beads sectional area n.exc 3 Sqcm for glazed or gauged Joinery, ceiling including secured with nails, complete all as specified and directed.

Supply and fixing in repairs for Block board 18/19 mm thick, grade 2 quality, interior grade, commercial type, fixed with nails/screws in cup board shutter/pelmets etc. or to timber frame work, complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) not exc 1.5 sqm, complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm and n'exc 4.00 Sqm, complete all as specified and directed.

Supply & fix powder coated aluminium frame for doors, windows ventilators with one of more rebates including joining cleat for fixing etc., complete all as specified and directed. (Thickness of powder coating not less than 50 micron).

Supply & fix powder coated aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges powder coated aluminium snap beading screws etc. complete all as specified and directed. (Thickness of powder coating not less than 50 micron).

Supply & fix powder coated aluminium window and ventilator shutters, side hung type without sash, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150 mm long (1 no.) hinges type B-21 100 mm long ( 2 nos) suitable handles (1 no.) complete all as specified and directed. (Thickness of powder coating not less than 50 micron).

Supply and fixing 9 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations fixed with screws to aluminium door shutters, complete all as specified and directed.

Supply and fixing 5.5 mm thick tinted sheet glass and glazing with aluminium beading & rubber gasket in square in each panes , complete all as specified and directed.

Supply and fixing factory made UPVC door frame made of UPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing 24 mm thick factory made UPVC door shutters to existing door frames made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanized/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a UPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter)

Dismantling PVC/CI/AC drain pipe of size 75/110mm, complete all as specified and directed.

Supply and fixing 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

Supply and fixing 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

Supply and fixing 75 mm bore PVC (SWR) bends any radius with access door, complete all as specified and directed.

Supply and fixing 110 mm bore PVC (SWR) bends any radius with access door, complete all as specified and directed.

Supply and fixing in repair wash-down water closet Orissa pattern size 580x440mm white with integral footrest and trap, including connection to drain and to flushing pipe including making good to floor and flush pipe and joint between flushing pipe and sockets of water closet pan, complete all as specified and directed.

Supply and fixing in repair vitreous china wash-down water closet pan & trap (pedestal pattern) with plastic water closet seat black closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device with flush pipe to pedestal pan including all joints including connection to drain pipe and flush pipe, complete all as specified and directed.

Supply and fixing in repair PVC low level flushing cistern 10 ltr capacity, valve less, symphonic action type with inlet, ball valve float and handle including bracket and flush pipe 32 mm dia, complete all as specified and directed.

Supply and fixing in repair vitreous china white wash hand basin flat back size 550x400 mm including brackets chain & plug and waste pipe waste coupling etc., complete all as specified and directed.

Supply and fixing in repairs Health faucet with steel tube 1.5m long with screwed nut for inlet connection, complete all as specified and directed.

Supply and fixing in repair 15mm bore, steel water tubing, medium grade, galvanised with all fitting and fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Supply and fixing in repair 20 mm bore, steel water tubing, medium grade, galvanised with all fitting and fixed to walls and ceiling or laid in floors, complete all as specified and directed.

Supply and fixing in repairs 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing in repairs 20 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing in repairs 15 mm bore self closing pillar taps, cast copper alloy, chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed for iron pipe and fixed, complete all as specified and directed.

Supply and fixing in repairs 15 mm bore stop valves, fancy type chromium plated cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed, complete all as specified and directed.

Supply and fixing in repairs 20 mm bore stop valves, fancy type chromium plated cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed, complete all as specified and directed.

Supply and fixing in repairs 32 mm bore waste coupling of PTMT (half or full threaded). Minimum weight 45 gms), complete all as specified and directed.

Supply and fixing in repairs 32 mm bore bottle trap of PTMT having minimum water seal of 25 mm. (Minimum weight 260 gms), complete all as specified and directed.

Supply and fixing in repairs grating doom 100 mm dia of PTMT. (minimum weight 25 gms), complete all as specified and directed.

Supply and fixing in repairs grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms), complete all as specified and directed.

Supply and fixing in repairs Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 300 mm, complete all as specified and directed.

Supply and fixing in repairs kitchen sinks of Stainless steel 1.00mm thick with plugs, washers and waste pipes and cast iron cantilever brackets including and connecting union to pipe over all size 495mm X 420 mm bowl size 410mm X 330mm X 160mm, complete all as specified and directed.

Taking down aluminium shutters of any description exceeding 1 Sqm and not exceeding 2.50 Sqm each and refixing in the same opening after easing and adjusting including refixing builders hardware as required and renewal of unserviceable screws, complete all as specified and directed.

SAI DIVYA DEVELOPERS AND BUILDERS

ANJANA ENTERPRISES

SREE VIGNESWARA CONSTRUCTIONS

M/S REAL POWER SYSTEMS

GVR CONSTRUCTIONS

sai ganesh enterprises

MAHIRA ENGINEERING & INFRASTRUCTURE