REPAIRS TO RCC ROOF , CHAJJAS, CERTAIN PLASTER TO BLDG INCLUDING PAINTING , REPAIR TO PATH AND PLINTH PROTECTION AND REPAIR TO ROLLING SHUTTERS , GATES , CUPBOARDS AND CERTAIN MISC ITEMS AT INF LINE JAMNAGAR UNDER GE (A) JAMNAGAR

Amount

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for keys scrubbing down with water etc. complete all as specified and as directed by Engineer-in-Charge

Dismantling timber fillets , rails , posts, rafters, purlins etc under 40 sqcm in section, framed work complete all as specified and as directed by Engineer-in-Charge

Dismantling boarding , any description , fixed in any position with nails complete all as specified and as directed by Engineer-in-Charge

Demolition Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level complete all as specified and as directed by Engineer-in-Charge

Demolition of brick work or stone/boulder masonary built in CM including all quoins, arches, pillars, etc but excluding ashlar, facing, dressed stone work and pre-cast concrete articles complete all as specified and as directed by Engineer-in-Charge

M&L 15 mm thick rendering on other than fair faces of external wall of brick/ stone / block masonary or concret surfaces in two layers Ist layer shall be 10mm in cm 1:6, secound and final layer shall be 5mm thick in CM 1:4 finished fair and even without using extra cement mixed with integral water proofing compound complete all as specified and as directed by Engineer-in-Charge

M&L Prepration of newly plastered surface of wall by hand held sander / long handle sander including cornices, pilasters etc and appliying with Airless spray two or more coats of 100 % premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @1.43 litre/10Sqm over and including priming coat of exterior primer applied @ 0.9 ltr/10sqm complete all as specified and as directed by Engineer-in-Charge

M&L for Prepration by hand held sander / long handle sander including cornices, pilasters etc of newly plastered on wall complete all as specified directed and applying three coat of white wash, complete all as specified and as directed by Engineer-in-Charge

M&L 5 mm thick rendering on ceiling or concrete surfaces in cm 1:3 finished complete all as specified and as directed by Engineer-in-Charge.

M&L complete removal of existing tretment by hand held sander / long handle sander washing down with Jet washer and appliying Airless spray two or more coats of 100 % premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @1.43 litre/10Sqm over and including priming coat of exterior primer applied @ 0.9 ltr/10sqm complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing roof treatment, removing rubbish off the premises, cleanning the surface and preparing to receive new roof treatment and applying roof treatment as under:- (a) Applying coat of bituminios primer @ 0.40 litre/ Sqm on prepared surfaces and allow to dry(the primer and the membrane to be used shal be of same manufacturer, (b) Supply and laying of minimum 3 mm thick APP modified polymeric membrane weighting not less than 3 KG/ Sqm black finish reinforcement with non woven polyster matt with help of torching with proplane or abutance gas using torch with minimum 75 mm side overlap and 100 mm end overlap. (c) two coat of approved aluminium paint over membrane complete. (d) all overlaps and joints shall be sealed as per manufacturers instruction complete all as specified and as directed by Engineer-in-Charge.

Roughening surfaces of old concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc incl brushing neat cement slurry with 3.0 kg of cement per sq metre complete all as specified and as directed by Engineer-in-Charge.

M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 10 mm thick in CM(1:3) with using water proofing compound on fair faces of brick work/ Fasia and roof surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course complete all as specified and as directed by Engineer-in-Charge.

M&L for racking of cracks upto 5 mm wide ,preparation and crack filling with ready to use crack fiber reinforced filler /chemical based crack fillers by approved manufacturer and filling as per manufacturer instructions in walls,roofs of any type or size (Make: Pidilite/dr fixit,fosroc, or equivalent as specified make) complete all as specified and as directed by Engineer-in-Charge.

M&L for racking of cracks exc 5 mm but not exc 10mm wide ,preparation and crack filling with ready to use crack fiber reinforced filler /chemical based crack fillers by approved manufacturer and filling as per manufacturer instructions in walls,roofs of any type or size (Make: Pidilite/dr fixit,fosroc, or as specified make) complete all as specified and as directed by Engineer-in-Charge.

Removing the plant/growth of any description size, any location of external surfaces of walls shafts by cutting & remvoing the roots completely spraying the suitable chemical (each plant 100 ML) in the removed portion to avoid re-growth & making good damaged portion to match the existing surfaces by PCC type B0 (1:2:4) 12.5 mm graded aggregate complete all as directed by Engr In Charge (Chemical :- Gramzone/Roundup or equavalent suitable chemical to remove/destroy the plants/roots)

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls/chajja by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement . clean loose rust from bars manually with brush . fixing new supplymentary bars if required,either by tying it with existing bars or by welding on it. Applying eppoxy bonding agent and making good with polymer modified plaster/micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including formwork complete all as specified and as directed by Engineer-in-Charge.

Supply only of Intergral water proofing compound as per complete all as specified and as directed by Engineer-in-Charge.

M/L 2nd class Hardwood plain fillets , square , rectangular or trigular in section , with sectional area exc 13sq cm and n exc 25sqcm, clean swawn , secured with nails or brads complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 100mm extruded brass handles, fabricated type polished and fixed with nut, screw and washer of mild steel complete all as specified and as directed by Engineer-in-Charge.

S/F in repairs for Block boards, 18/19mm thick grade 2 quality, interior grade, decorative type with veneer/lamination as approved on both face fixed with screws to timber and frame work complete all as specified and as directed by Engineer-in-Charge.

S&F 30mm width of flap continuous (piano) hinges, mild steel, bright finish complete all as specified and as directed by Engineer-in-Charge.

S&F S/s door magnets/ catcher for cupboards , fixed with screws complete all as specified and as directed by Engineer-in-Charge.

S&F for s/s cabinet chains 150mm long for cupbords ( corrosion ressistive), fixed to both sides with screws complete all as specified and as directed by Engineer-in-Charge.

M/L preparation of wooden surface of any description, n exc 10cm width or girth when connected with other painting or when painted in different tint and applying two coats of synthetic enameled painting over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.

M&L for 75mm thick cement concrete Type C-2 ,1:3:6,( Using 40mm graded aggregate) as in plinth protection , subbase complete all as specified and directed by Engr-in-charge.

S & F Framed work such as grills , gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; framed and hung as gates, including pintle hinges, stops, hand made sliding bolts , etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

Fabrication and fixing only Framed work such as grills , gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; framed and hung as gates, including pintle hinges, stops, hand made sliding bolts , etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

M&L for Hold fast for fixing of chowkats and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed by Engineer-in-Charge.

Providing cement concrete type BO 1:2:4 (12.5mm graded aggregate) in cills, steps, seismic and other similar bands plinth coureses string courses lacing courses parapets and railing copings kneelers apex bed plates kerbs. etc.. water troughs and the like including wethering slightly rounded or chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for Brickwork with fly ash moudular bricks built in CM (1:4) , straight or curved on plan exc 6m mean radius, complete all as specified and as directed by Engineer-in-Charge.

Demolition Cement Concrete (reinforced) in Roofs, floors (other than ground floors), beams, shelfs, staircases, landing, chajjas and similar suspended work complete all as specified and as directed by Engineer-in-Charge.

M&L 1:1.51:2.92 in beams, cantilevers, bressumers, as in chajja (upto 9mtr height) complete all as specified and directed by Engr-in-Charge Note : Min cement content 425kg/Cum, coarse aggregate 20mm (60%) + 12.5 (40%), slump 50mm and w/c ratio 0.4. Before commencement of work contractor will carry out Trial Mix at site and take the trial mix approval by GE. ( avg comp strength 7 days 33.33 N/mm2 and 28 days 44.85 N/mm2)

M&L for Formwork to flat soffits and edges of chajjas and similar works complete ( including necessary scafolding ) all as specified and directed by Engr-in-charge.

S&F Mild steel bars (TMT bars) 10 mm and above, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engr-in-Charge.

Servicing and greasing of rolling shutter of any type and thickness including replacement nut , screws , etc including taking down carefully of rolling shutter and cover upto height of 3.5 mtr , greasing of all parts for smooth functioning of shutter and refixing the same in existing opening/position complete all as specified and as directed by Engineer-in-Charge.

Servicing and greasing of rolling shutter of any type and thickness including replacement nut , screws , etc including taking down carefully of rolling shutter and cover upto height of 7.0 mtr , greasing of all parts for smooth functioning of shutter and refixing the same in existing opening/position complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs for Steel rolling shutters with thickness of lath 1.0 mm, gear operated type with bevelled gear box and and crank handle, without ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indi cated, complete: including taking down old one complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old steel surface of any description and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs for safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs for ball bearing for rolling shutters complete all as specified and as directed by Engineer-in-Charge.

M&L for hardcore (broken stone or boulders) of gauge n exc 63mm, deposited, spread and levelled in layers n exc. 15cm thic, watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge.

M&L for cement concrete 1:4:8 type D-2 (40mm aggregate) foundation, sub base of floors , filling mass etc.concrete complete all as specified and directed by Engr in charge.

M&L factory made 60mm thick Machine pressed precast cement concrete coloured, rubber moulded, designer(reflecting type) interlocking pavour block of M-35 grade confirming to IS 15658-2006 of shape and size as directed with coloured top laid over and including 50mm thick sand cushioning, joints of blocks filled with dry sand and compacted complete all as specified and dierected by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

sanu enterprise (BID ID -3397790)

M/S JAYCONSTRUCTION CO (BID ID -3405914)