CA NO.CWE BLY/GE (E)112 OF 2024- 2025 PROVN OF FARRIER SHOP NEAR PHARMACY OF 883 AT BN ASC UNDER GE (EAST) BAREILLY

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed.

M&L for cement concrete 1:4:8 type D 2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for Reinforced cement concrete (Design Mix) with M-25 (using 20 mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete. complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batte on rough finished flat surface of concretecomplete all as specified and directed.

M & L for Reinforced cement concrete (Design Mix) with M-25 (using 20 mm graded stone aggregates) as in Columns, pillars, piers, posts and strutscomplete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions on rough finished flat surface of concrete complete all as specified and directed.

M & L for Reinforced cement concrete (Design Mix) with M-25 (using 20 mm graded stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span. complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, wall of mangers etc. complete all as specified and directed.

S&F mild steel TMT bars of 8 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Ditto,but upto 8 mm dia as in stirrups , spacers and binders complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins, vertical post where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 -W (Gde- E-250) quality-A complete all as specified and directed.

S&F Hand rails, half round or other mild steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shapeas directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Framed work such as chowkhats grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, frames; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F mild steel screw bolts (Machine made) with hexagonal or square heads at one end and the screwed the other to be fitted with washers and one hexagonal or square but exc 5 cm but n.exc 10 cm long, dia of shank 5 to 10 mm complete all as specified and directed.

S & F in repair Pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L in repair for 0.8 mm plain galvanised mild steel sheeting in ridge, hip, vally gutter, drip and straight flashing class 8 mm zink coated @ 120 gms/sqm fixed with L-type or J-type or crank hooks bolts complete all as specified and directed..

M&L brick work with fly ash bricks (old size) conforming to IS 12894 -2002 specification straight or curved on plan exc 6m mean radius, built in CM1 : 6 complete all as specified and directed.

M&L for 15 mm thick cement plaster in CM 1:6 on brick or concrete surface finished even and smooth without using extra cement Complete all as specified and directed.

M&L for 15 mm thick cement plaster in CM 1:4 on brick surface finished even and smooth without using extra cement Complete all as specified and directed.

M&L hardcore of gouge n exc n exc 63mm broken stone or boulder, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75 mm thick PCC type D-2, 1:4:8 ( usng 40 mm graded stone aggregate) as in sub base and finishing the surface even and fair complete all as specified and directed.

M&L for PCC 1:11/2:3 , B1 (using 20mm graded aggregate) as in flooring/hard standing and finishing the surcafe even and smooth woth out using extra cement complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Gared A complete all as specified and directed.

S&F Welded steeel wire fabric to steel member exc 4kg per sqm complete all as specied and directed.

M&L for two coats of OBD with preparing newly plastered walls surfaces with airless electric sprayers over a coat of primer applied using airless electric spryers over two coat of wall care putty of 1mm thickness prepared and sanded with electrically operated sanding machine. Application to be done through authorised applicator of manufacturer complete all as specified and directed.

Material and labour Material for applying Two coats of cement base paint on newly platered surface by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with max material hose length 30 mtr. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturerand accessories for applying cement base paint should be able to spray in hard to reach areas and penetration of cement base paint on the surface to achive excllent application using limited manpower complete all as specified and directed.

Returning, filling in, including spreading, leveling, and well ramming in layers n. exc. 25 cm thickness in soil.complete all as specified and directed.

Removing excavated material (Soils) to distance of exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point. complete all as specified and directed.

Supply and spreading sand filling under interlocking tiles and for pritection of under ground cable including watering and consolidation complete all as specified and directed.

M & L for Machine pressed precast conctete interlocking paver block with grey cement and pigment any shape ,size and colour confirming to IS 15658-2006of 60 mm thickness, M-40 Grade, complete all as specified and directed.

M & L two coats of synthetic enamel paint on steel surfaces over one coat of red oxide or zinc chrome primer, of any description over 10cm width or girth including preparation of new or previously untreated surfaces of steel. compete all as specified as directed.

M & L for 75 mm thick cement concrete type C2. 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection and finish even and fair all as directed.

M&L for concealed point wiring for one light/ fan/ bell point controlled by one switch with 1.5 Sqmm (Nominal area) PVC insulated, unsheathed, stranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including PVC conduits of 20 mm dia with all fittings and accessories alongwith PVC insulated cable with copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 2mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/carbonite sheet cover fixed with screws,cap and washers including making good the disturbed surfaces complete all as specified and directed.

M&L for concealed point wiring with 2.5 Sqmm (Nominal area) PVC insulated,unsheathed, multi stranded Copper conductor cable FRLSH drawn in and including PVC rigid PVC conduit 25mm or higher size with all its fittngs and accessories for one 3 pin/6 pin 15 Amps socket out let point independent alongwith PVC insulated cable with solid copper conductor 2.5 Sqmm (nominal area) continuous earth wire, and connected to earth dolly including fixing of 1.20mm sunk pressed steel terminal box suitably flushed to wall with 3mm thick Hylum sheet cover fixed with screws & cup washers incl. making good complete all as specified and directed.

S&F switch piano flush type single pole one way 5/6 Amps complete all as specified and directed.

S&F Switch Piano flush type single pole one way 15/16 Amps complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin 5/6 & 15/16 Amp flush type complete all as specified and directed.

S&F ceiling rose, 3 terminals, PVC polycarbonate isolated body complete all as specified and directed.

S&F in replacement LED Tube light fittings1x 20 Watt ( T-8 ), 4' long, 220 Volts, AC decorative box type with driver,holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F Exhaust fan steel body AC single Phase 230 V of size 300 sweep with blades and frame and louvers complete all as specified and directed.

S & F Ceiling fans complete with blades, down rods, electronic regulator and accessoreis 230 V 1200 mm sweep, Min air delivery 210 CFM with service valuve 6.00 BEE Five star rated with brushless directed current motor (BLDC) complete all as specified and directed.

S&F Sheet mental enclousers DBS) when MCBs to be used 4 way , 240 Volt double door single pole & neutral with 200 Amps rated bus bar complete all as specified and directed.

S&F MCB Single phase and neutral 40-63A, 230 V 10 KA 'C' Curve type complete all as specified and directed.

S & F MCB SP 6A-32A, 230V, 10 KA 'B' Curve type complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 60cm×60cm× 6mmmm thick, buried directly in ground, vertically to a depth not less than 2.25 mtr deep below ground level with top edge of the earth plate at depth not less than 1.5 mtr below ground level earth plate surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, earth lead GI wire 4mm dia by means of bolts, nuts, check-nuts and washers of galvanized iron and thimbles and of earth wire protected by galvanized iron pipe light grade 15mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh complete including excavation and earth work, PCC chamber and cover in cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in lieu of CI cover and frame etc complete all as specified and shown in electrical plate No. 3 of SSR-2009 (Part-I).

S & F XLPE insulated armoured heavy duty electric cable with stranded aluminum conducjtor 1100 volts grade cross sectional area 4 sqmm 2 core complete all as specified and directed.

M & L for laying GI Tubing light grade 40mm dia with all fittings for cable protection complete all as specifed and directed.

S & F brick with fly ash bricks (old size) conforming to IS 12894 -2002 specification laid dry for protection of cable complete all as specified and directed.

M/S ABHISHEK ENTERPRISES (BID ID -3267712)

Tameer Enterprises (BID ID -3265395)

QUALITY CONSTRUCTIONS (BID ID -3268329)