Construction of First Floor Building and Providing Painting , Electrical , Water supply arrangments,Tiles Laying Additional works to Ground Floor Building at New Urban Primary Health Centre Lakshmi nagar srirangam in Ward no01

Amount

Investigation charges for Geophysical survery finding of yeild to the point drilling of Borewell for all etc., complete

Drilling of 150mm (6”) nominal dia vertical borewells anywhere in Tamilnadu in all formations, suitable for down the hole hammer drilling such as medium hard rock to hard rock formation, consolidated formation etc and drilling over burden to a dia not less than 200mm including insertion of 165 mm PVC casing pipe, couplings caps and other relevant materials required upto the depth as directed by the Engineer or his representative including grouting of cement 25kg (minimum) up to the depth of over burden are including borewell development flushing of borewell at a pressure 7kg/cm2 (100 lb per square inch) including yield test, crew charges, cost of consumables, transportation charges of casing pipes and all other materials including assembling complete to the satisfaction of the Engineer and as stipulated in the technical specification. The entire works should be carried out as per IS 2800 Part I & II / 1979. Finished dia of borewells shall not be less than 145mm

Supply and delivery of clear water vertical wet type 3phase submersible pump 3HP suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS 9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 % (50 Lpm X 75 m )

Labour Charges for the erection of Submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, and erection of panel board consisting of TPICN swtiches starter voltmetre, Ammeter, three point (indicating) lamps capacitor single phasing preventor and laying and jointing the cable and twin earthing for etc., Complete and testing the pumpset and trail run for 10 days.

Supply and Delivery of 200mmdia PVC casing Pipes including cost and conveyance of materials and labour charges etc. complete as per standard. Specifications

Supply and delivery of direct online starter confirming to IS13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

supply and delivery of PVC inclused and sheated 3 core flat type 2.5sq.mm castle conformustsq.m

Centering for soffits of RCC Slabs of plane surface like lintels, beams, etc., including strutting 3m high using mild steel sheets of size 90cm x 60cm x and B.G 10 stiffened with M.S angles of size 25mm x 25mm x 3mm laid over silver oak (C.w) joists of size 10cm x 6.5cm (spaced at about 90cm c/c) and supported by casurina props of 10cm to 13cm dia (spaced at 75cm c/c) complying with standard specification

With Strutting

Column

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers -

First Floor

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors etc., complete as per standard specification

Brickwork in CM 1:5 (One Cement & Five Crushed Stone Sand (M- Sand) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification.

First Floor

Special Ceiling Plastering for RC slabs and beams with cement mortar 1:3 mix 10mm thick including hacking etc., complete

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications .

Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with design Antiskid Ceramic tiles (colour and shade as directed) of size 305mm x 305mm x 6mm in all floors over a base layer of cement mortor 1:3, 20mm thick laid in-situ and pointed with same coloured cemnent etc., complete complying with standard specification

Supplying & fixing door shutters for Solid Core Flush Shutters with Teak ply on both side with teak wood lipping alround 35mm thick, single leaf confirming to IS:12406/1989 with 35x12mm T.W. Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings, such as 300 mm tower bolt 2nos, 200mm towerbolt 1 No. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos and 1No. Door stopper etc complete.

Supply and fixing of Solid PVC door shutters with frame using 19 guage 19mm Ms square tubes for styles and outer frame 15mm MS square tubes for top lock bottom rails. The steel square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutterrs using 5mm thicksolid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. the overall size of styles shall be 50mm x 30mm. the overall size of top rail, lock rail and bootom rail shall be 75mm x 30mm. the ovrall size of frames shall be 50mm x 45mm with suitable rebate for housing the shutters. etc., complete complying with standard specification

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc.,

Manufacturing, supplying & fixing in position Steel windows glazed with openable shutter frame and shutter frame made out of steel section confirming to IS 7452/ 1990.Theouter frames of windows made of Z section (F7D) of size 25 x 20 x 3 mm confirming to IS7452/1992 mullions are made of (F4B) of section size 46x25x3mm confirming tolS7452/1990.The shutters are individual and each of them can be operated separately.Sash bars are made of Section (T2) of size 25x22x3m, 2nos of sturdy hinges and onenumbers of handle cum slatch of special type are fixed for with openable shutter. Suitableopening is left for its any operation. One number of adjustable stay with locking bracketof sufficient length shall be provided for each shutter 4 nos. of 40x40x3mm anngle hold fast 230mm length are welded to the outer frame at appropriate point.M.S square bars of 12mm size is welded to the inner face of the window at equal intervals not excluding 10cm spacing’s,3mm pin headed glass is used for glazing and the glass panes shall be fixer, with good quality T.W.beeding size 15x15mm with screws for fixing. Grill members are painted with one coat of primer. Also rate is inclusive of cost of all materials, labour charges for fixing, one coat of primer, welding charges transportations to the work site, loading unloading and all other incidental chargers etc., completed.

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns,beamsor masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supplying and fixing in position of alu.Anodised partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical membersare spaced at 90cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4 M height the bottom panels should be covered with 12mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass with necessary glassing clips, rubber beading including dismandling holes in RCC columns, beams masonry wherever necessary with the power drill it extended. all the Aluminium must be anodised to 1.5 microns as per standard specification

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectanguLAB Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.

Supplying and laying in flooring with fully polished colour granite stone of 20mm thick of 4' x 2' in size laid over base layer of cement mortor 1:3 20mm thick and applying cement slurry & pointed with white cement and colour pigment to the colour of stones and polished neatly as per directed by the deparmental officers

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers etc., Complete as per standard specification.

Supplying and fixing best approved quality Oval Shape Wash hand basin of size 560 x 450mm including the cost of teak woodplugs, brass screws complete complying with standard specification.

Supplying and finishing in position 15mm diameter brass/ CP screw down tap/ (heavy duty of approved make confirming to I.S specification and quality including cost of shellac, thread etc. complying withstandard specification and including cutting and thraeding wherever necessary etc., Complete as per standard specification (SD TAP)

Supplying and fixing best approved quality Brass CP/Alu. anodised Towel rail 600 mm. long and 20mm diameter with brackets of same materials including cost of teak wood plugs and CP screw etc., complete complying with standard specification

Supplying and fixing best approved quality CP soap tray of size 150mm x 100mm including the cost of teak woodplugs, brass screws complete complying with standard specification.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm] etc., complete as per standard specification

Supplying and fixing in position best quality PVC soil/waste pipe (6KSC) of various size having ISI marks and providing leakproof joints including fixing to the wall PVC/Ms clamps etc., and making connection to all sanitary fittings, dismandling masonry /RCC works complying with standard specification

110mm PVC Pipe

90 mm PVC Pipe

Supplying and fixing in position PVC special such as plain bend, plain tee, door tee, offsets, y-junction plain with various sizes best qualityconfirming to ISS and providing leak proof joints including fixing to wall and giving connection to the PVC soil stacks, dismandling the brick masonry or RCC floor or Roof slab and redoing dismandling portionto original condition

110 mm PVC tee

110 mm PVC elbow

90 mm PVC tee

90 mm PVC elbow

Supplying laying and jointing UPVC pipes of approved quality and best variety of B class Pipes of the following pipes including fixing GI special but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs,clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc.,complete. as per standard specification - internal Open

32mm dia ( Internal open)

25mm dia ( Internal open)

20mm dia ( Internal open)

Supplying and fixing UPVC specials of approved quality and brand including all labour and material charges etc., complete as per standard specification

32mm dia UPVC Tee

32mm dia UPVC Elbow

32mm dia UPVC coupling

32x25mm dia reducer

25mm diaUPVC Tee

25mm dia UPVC Elbow

25mm dia UPVC coupling

25x20mm dia reducer

20mm dia UPVC Tee

20mm dia UPVC Elbow

20mm diaUPVC coupling

20x15mm dia reducer

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. etc., complete as per standard specification

32mm Gun Metal Valve

25mm Gun Metal Valve

20mm Gun Metal Valve

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supply and delivery of HDPE tank as per IS 1201/1996 including loading, unloading, transportation and labour charges for fixing the GI special for pipe connection including cutting threading and fixing etc., complete as per standard specification

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour - (SD 56 PWD Electrical Data)

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors. etc., complete as per standard specification

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) etc., complete as per standard specification (PWD ELECTRICAL DATA SD 17)

Wiring with 2x1.5sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3 mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 1.5sq.mm copper wire and making good of the concealed portion with suitable colour for concealed PVC plug point (sd 38)

Wiring with 2x4 sq.mm.PVC insulated SC unsheathed FRLS copper conductor cable of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with150mmx100mmx113mm TW switch box with 3 mm thick hylem sheet for 15A 3 pin non inter locking wall socket with15A flush type switch with continuous earth wire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour for concealed power plug point (sd 40)

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp (sd 107)

Earting as per PWD standards with an earth electrode of 2mts class B GI pipe of dia 32mm complete with necessary masonry works etc., complete as per standard specification (SD212)

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100 A 4P MCB Isolator as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End -sd 579

Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete etc., complete as per standard specification - (SD 129 PWD Electrical Data)

Supply and run of 4 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in 25mm dia GI pipe (Class 'B') bent at both ends with necessary angle iron up right and end supports for mains(SD No.72)

Supply and delivery 32mm GI service pipe including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specification

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Weathering course with concrete broken brick jelly 20mm size in pure slaked lime (no sand to be used) over RCC roof slab the proportion of broken brick jelly to lime being 32:12.5 well beaten with wooden beaters giving required slopes and thickness etc., complete

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (one cement & Three P-sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete (The crushed stone sand to be used in base mortar shell confom to gradation as per IS 1542-1977)

NACHIYAR CONSTRUCTION (BID ID -1500455)