Construction of Combined office building at Janjehali in Tehsil Thunag Distt Mandi SH C/o Building portion WS and SI Rain water harvesting system and site development

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in all kinds of soil in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto any lead , including getting out the excavated soil and disposal of surplus excavated soils as directed, within any lead. Ordinary rock including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in all kinds of soil including getting out and disposal of excavated earth upto any lead , as directed by Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (one Cement : four coarse sand) : eight graded stone aggregate 40 mm(fourty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm (fourty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying cement concrete 1:3:6 (one cement : three coarse sand : six graded stone aggregate 20 mm (twenty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (twenty millimetre) nominal size over 75mm(seventy five millimetre) thick bed of dry brick ballast 40 mm (fourty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre) in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement: 3 Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm (fourty millimetre) nominal size and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size and finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . Foundations, footings, bases of columns, sqm etc. for mass concrete.

Suspended floors, roofs, landings, balconies and acceess platform.

Lintels, beams, plinth beams, girders, sqm bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts .

Stairs, (excluding landings) except spiralstaircases.

Edges of slabs and breaks in floors and walls : Under 20 cm (twenty cenimetre) wide.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Providing, hoisting and fixing above plinth level up to any floor level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (one cement : three coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (one cement : one point five coarse sand) : three graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of Thermo-Mechanically Treated bars of grade Fe-500D or more. approved make from factory / workshop to construction site including placing in position and binding all complete up to any level including cost of binding wire including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying in position machine batched and machine mixed design mix M-25 (M- twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability up to any floor level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing any laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admistures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strenght and durability, all works above plinth level upto any floor level including carriage of materials with in all leads, lifts and other incidnetals as per the direction of Engineer-in-Charge.

Providing and laying Reinforced cement concrete work 1:1.5:3 (one cement : one point five coarse sand) : three graded stone aggregate 20 mm (twenty millimetre nominal size) M-25 design mix up to any floor level , excluding cost of centering, shuttering, finishing and reinforcement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. beams, suspended floors, roofs having slope up to 15° ( fifteen degree) landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level .

walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to any floor level in all shapes and sizes in :Cement mortar 1:6 (one cement : six coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in Cement mortar 1:6 (one cement : six coarse sand) in foundation and plinth in all shapes and sizes including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5(seven point five) in Cement mortar 1:3 (one cement :three coarse sand) superstructure above plinth level up to any floor level. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in foundations and plinth in : Cement mortar 1:3 (one cement : three coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying 20 cm. (twenty centimetre) thick composite Punched Ashlar stone masonry with stone facing of bluish shade with 1.25 x 1.25 cm (one point twenty five into one point twenty five) groove exposed from outside in cement mortar 1:6(one cement :six sand) and concrete backing with cement concrete 1:3:6 (one cement: three sand: six graded stoneaggregate 20 mm. (twenty millimetre) nominal size) on inner face of walls including centring,shuttering and propping complete up to floor five level. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Ist quality GRC/ Unistone wall cladding conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement : three coarse sand) and jointing with grey cement slurry @ 3.3kg (three point three kilogram) per sqm, including pointing in white cement mixed with pigment of matching shade complete. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 37 mm (thirty seven millimetre) thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm ( one hundred into thirty seven millimetre) with wall thickness 2 mm (two millimetre) (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos (two number) of plastic brackets of size 75 mm x 220 mm (seventy five milimitre into two hundred twenty millimetre) at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm (twenty eight millimetre into thirty millimetre), with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm (one hundred into thirty seven millimetre), wall thickness 2 mm (two millimetre) (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm ( one hundred into twenty millimetre), and inserting 2 nos (two number) tie bar of 6 mm (six millimetre) dia and fastening with nuts and washers complete, all as per manufacturer's specification including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing 1st class Kiln Seasoned deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought,framed and fixed in position complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ISI marked decorative flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm (thirty millimetre) thick including ISI marked Stainless sqm Steel butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing factory made uPVC white colour Two track two panels sliding door made of (big series) frame 67 x 50 mm (sixty seven into fifty millimeter) & sash 46 x 82 mm (fourty six into eighty two millimetre) both having wall thickness of 2.3 ± 0.2 mm (two point three into ± ziro point two millimetre) and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm (two square metre) ( upto 5.00 sqm) (five squaremeter) sliding glazed door comprising of uPVC multichambered frame with in-built roller track and sashextruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty ± zero point two millimetre)) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVCextruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) handle with key on one side of extreme panels alongwith zinc plated miled steel multi point locking having transmission gear with keeps, zincaloy (white coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm ( one hundred into eight millimetre) size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).)complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing factory made uPVC white colour casement/ Casement door with top hung ventilator with 3D and S.S. friction hinges 400 x 19 x 1.9 mm (four hundred into nineteen into one point nine) made of (big series) frame 67 x 64 mm (sixty seven into sixty four millimetre) , sash 67 x 110 mm (sixty seven into one hundred ten millimetre) & mullion 67 x 80 mm (sixty seven into eighty millimetre) all having wall thickness of 2.3 ±. 0.2 mm (two point three ±. zero point two millimetre) and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto any sqm) cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm (one point sixty ± zero point two millimetre) thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm (one hundred into eight millimetre) size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in- Charge. (Single / double glass panes and silicon sealent shall be paid separately). complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing factory made uPVC white colour Fixed window / ventilator made of (small series) frame 47 x 50 mm (fourty seven into fifty millimetre) & mullion 47 x 68 mm ( fourty seven into sixty eight millimetre) both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto any sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm (one hundred into eight millimetre) size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm (thirty five into thirty five into five millimetre) , joints mitred and welded by angle iron 35x35x5 mm (thirty five into thirty five into five millimetre) or 35x 5 mm (thirty five into five millimetre) flat pieces to the existing Tiron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). in Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked Panelling for panelled or panelled and glazed shutters 25 mm (twenty five milimetre) to 40 mm (fourty millimetre) thick : with nickel plated piano hinges with screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm (two hundred millimetre) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge. (Only weight of grill to be measured for payment). including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 300x16 mm (three hundred into sixteen millimetre) corrosion resistant AISI-Grade stainless steel sliding door bolts with nuts and screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing corrosion resistant AISI-Grade stainless steel Tower bolts with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 200x10mm (Two hundred into ten millimeter) .

150x10mm (One hundred fifty into ten millimeter).

Providing and fixing Stainless steel handles of approved quality with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 125 mm (One hundred into twenty five millimeter).

100 mm (One hundred millimeter) .

75 mm (seventy five millimeter) .

Providing and fixing chromium plated brass 100 mm ( one hundred millimetre) mortice latch and lock with 6 (six) levers and a pair of lever handles of approved quality with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Stainless steel hard drawn hooks and eyes including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 250mm (Two hundred fifty millimeter)

200mm(Two hundred millimeter)

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 150 mm double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for doors including cost of cutting floor as required embedding in floors and cover plates etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 19 mm (ninteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from out side shall be finished with 4 mm (four millimetre) thick vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying Heavy Duty Cobble Stone 100x100x100 mm (one hundred into one hundred into one hundred millimetre) of approved shade stone laid over 25mm. (twenty five millimetre) Thick cement mortar bed of 1:4(onecement: four sand) including pointing with cement mortar1:3(onecement:three sand complete includng pianohinges and other ascessories including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying vitrified floor tiles in 450x450x15mm ( four hundred fifty into four hundred fifty into fifteen millimetre) exterior grade with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 40 mm (forty millimetre) thick Cement concrete flooring 1:2:4 (one cement : two sand: four graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing 8mm (eight millimetre) thick wooden Laminated flooring made in superior water Resistant High Density hard wood fibre board make action tesa of approved shade including fixing with all accessories including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying vitrified floor tiles of AGL/Johnson/Kajaria/Orient Bell or equivalant in size 600x600mmx10mm ( six hundred into six hundred into ten millimetre) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying vitrified floor tiles of AGL/Johnson/Kajaria/Orient Bell or equivalant in size 600x600mmx10mm ( six hundred into six hundred into ten millimetre) with water absorption less than 0.08 % and conforming to I.S.15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 8 mm (eight millimetre) thick full body vetrified tiles in matte finish of Asian/Johnson/Kajaria or equivalant 600x600x10mm ( six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 8 mm (eight millimetre) thick full body vetrified tiles in matte finish of Asian/Johnson/Kajaria or equivalant 600x600x10mm ( six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing And fixing glazed Digital tiles 300x600 x 8 mm (three hundred into six hundred into eight millimetre) thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm (twelve millimetre) thick cement mortar 1:3(one cement :three sand) and jointed with cement slurry. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying white cement based putty of average thickness 1.00 mm (one millimeter) of approved brand and manufacture over the over plaster wall surfaceto prepare the surface evean and smooth complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Wall painting (two or more coats) with plastic emulsion paint of Apex/Altek/Asian or its equivalent make on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including water thinable priming coat with cement primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm (five hundred ninty five into five hundred ninty five) of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (zero point five zero) (minimum) as per IS 8225:1987, Light reflectance of 85% (eighty five percent) (minimum). Non combustible as per BS:476 (part- 4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100% (hundred percent), thermal conductivity < 0.043 W/m K as perASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and Lsections suitably fixed according to tile size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying Pre-Laminated Particle Board 12 mm (twelve millimetre) thick ply panelling over soft wood frame 40 x 40 mm (fourty into fourty millimetre) @ 600 x 600 mm (six hundred into six hundred millimetre) c/c having decorative first class kiln seasoned teak wood polished beeding out of 25 x 12 mm (twenty five into twelve millimetre) and cornice of size75 x 60 mm (seventy five into sixty millimetre) with necessary screws priming coat on unexposed surface etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying Black granite stone in flooring 20mm (twenty millimetre) (average)thickness base of cement mortar 1:3(one cement: three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing sandwich puff roofing with top skin of 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing prepainted sandwich puff ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing prepainted sandwich puff valley 90 cm (ninety centimetre overall 0.60mm (Zero point six zero milimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5(five) microns over 5 (five) microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing flushing 38cm(Thirty eight centimeter) overall with 0.60mm ( Zero point six milimetre)thick prepainted sandwich puff sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 (twenty ) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five)microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 110 mm (one hundred ten millimetre) diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. PVC Plain Bend 87.5° (eighty seven point five degree) 110 mm (One hundred ten milimetre) dia.

Shoe 100mm dia(One hundred milimetre) dia.

Providing and fixing M.S. BP Sheet1.66 mm(One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Trusses and trussed purlins in buildings including carriage of materials with in all leads,lifts and other incidentals.

Gratings framed guard bars laddeds railing brackets and similar works including carriage of materials with in all leads, lifts and other incidentals.

In beams joists,channels angles,tees,flats with connectiong plates or angle cleats as main and cross beams hip and jack rafters purlins connected to common raffers and the like.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 62.5 mm x 50 mm (sixty two into five into fifty millimetre) hand rails in 1st class Indian teak wood straight length complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm (twenty into ten into two milimetre) braced with flat iron diagonals 20x5mm (twenty ito five milimetre) size with top and bottom rails of T iron 40x40x6mm (forty into forty into six milimetre) with 38mm(thirty eight milimetre) dia steel pully complete with bolts and nuts locking arrangements, stoppers, handles, including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 450 mm (four hundred fifty millimetre) internal diameter including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm (five centimetre to twenty centimetre) , in recharge pit, in the required thickness, for all leads & lifts, all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm (one point five to two millimetre) in recharge pit, in required thickness over gravel layer, including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm (five to ten millimetre), in the recharge pit, over the existing layer of boulders, in required thickness, including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 20 mm (twenty millimetre) nominal bore .

32mm (thirty two millimetre) nominal bore .

15 mm (fifteen millimetre) nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :. 25 to 40 mm (twenty five to fourty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre (one metre) spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 2532 OD pipe 32 mm (thirty two millimetre) .

2025 OD pipe 25 mm (twenty five millimetre) .

1620 OD pipe 20 mm (twenty millimetre) .

1216 OD pipe 16 mm (sixteen millimetre) .

Providing and fixing white vitreous china Angel C8915 wall mounting water closet of size 455x355x355 mm (four hundred fifty five into three hundred fifty five into three hundred fifty five millimetre) of approved shape including seat cover, and cistern fittings, nuts,bolts and gasket etc of Perryware , Cera,Jaquar, Hindware or equivelent complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing white vitreous china CURSE SET WC cat No. S1021114P extended wall mounting water closet of size 780x370x810 mm (seven hundred eighty into three hundred seventy into eight hundred ten millimetre) of approved shape including providing & fixing white vitreous china cistern Cat No. S1060106 with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc of Perryware , Cera,Jaquar, Hindware or equivelent complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing viterous China CASCADE NXT C0207 Wall Hung Closet 540x365x395 ( five hundred fourty into three hundred sixty five into three hundred ninty five millimetre) White Shade Wall hung WC with soft close seat cover, hinges, accessories set size mm of /Jaquar or equivalent complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Single piece slim concealed cistern with floor mounting frame installation kit and S-type Drain pipe conection set for wall hung WC (without flush control Plate) JCS-WHT-2400FS of Jaquar or equivalent including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Flushing Plate Control palate vignette prime (JCP-CHR-812415) Jaquar or equavalent including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing viterous China wash basin C8863(505x405x155) Basin (half Pedestal) In White Shade of Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing viterous China wash basin CRUSE SET CAT NO S2040101 Wash Basin 510 x 400mm (five hundred ten into four hundred millimetre) and pedestal cat no. S2090101 of perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing viterous China wash basin CASCADE NXT C0404 Basin With Half Pedastal C0379 In White Shade of Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing vitreous China Flat back urinal ASTUTE C 0586 ASTUTE water less Urinal 345 x365x 655 (three hundred fourty five into three hundred sixty five into six hundred fifty five millimetre) In White Shadeof Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm (five hundred ten into one thousand fourty millimetre) bowl depth 250 (two hundred fifty) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm (forty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm (fourty five centimetre) length 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work 40mm dia) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P. brass long nose bib cock Cat no.CON 107KN Jaquar or equivalent single control of approved quality conforming to IS standards. 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P. brass long nose bib cock Cat no.OPP -15037PM Jaquar or equivalent single control of approved quality conforming to IS standards. 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Swan neck pillar tap with left hand operating knob single control CON-CHR-123BKN of Jaquar or equivalent complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing OPP-15001PM Pillar cock Jaquar or equivalent as per direction complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Angular stop cock with wall flange of opel prime no. CON 150083KN Stop Cock of jaquar or equavalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Concealed stop cock with wall flange of opel prime no. CON 083FTK Stop Cock PM single control of jaquar or equavalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Angular stop cock with wall flange of opel prime no. OPP-15053PM jaquar or equavalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Angular stop cock with wall flange of opel prime no. CON 053KN of jaquar or equavalent single control complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P.Mixer for kitchen sink with casted swinging CON 309KN jaquar or equavalent complete In all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Soap dish recessed type stainless steel AHS-1531 of Jaquar or equivalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing Soap dish stainless steel CAN -1131N of Jaquar or equivalent complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Towel Rack with lower hanger No. AHS-1581H of hotelier series of JAQUAR, or equivalent of superior quality including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Corner glass self with bract No.ACN-1173 of hotelier series of JAQUAR, ESS-ESS or equivalent of superior quality including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Glass shelf 550 mm (five hundred fifty millimetre) long with C.P. Brass bracket and guard rail no. AQN-7771 of Jaquar or equivalent fixed with C.P. Brass screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing U Shaped wall mounted rail with hinges 600 x 100mm (six hundred into one hundred millimetre) Cat No. B2210107 and Wall Mounted Grab Bar 600mm (six hundred millimetre) Long CAT No. B2210106 jaquar or equivalent Superior quality including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 8 mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 metre (one metre) long with S.S. triangular plate to Eureopean type W.C. of quality including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge : 25mm (twenty five millimetre) .

20mm (twenty millimetre) .

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. : 15mm (fifteen millimetre) .

20mm (twenty millimetre) .

32mm (thirty two millimetre) .

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the dire

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150 mm (one hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90mm (one hundred ten into ninty millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PVC door bend with ovalaccess door, insertion rubber washer 3 mm (three millimetre) . thick bolts and nuts ISI marked complete including fixing with approved adhesive etc including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (tewenty millimetre) nominal size foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (fourty millimetre) nominal size, inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge: Inside size 120x90 cm (one hundred twenty into ninty centimetre) and 90 cm (ninty centimetre) deep including C.I. cover with frame (medium duty) 500 mm (five hundred millimetre) internal diameter, total weight of cover and frame to be not less than 116 kg (one hundred sixteen kilogram) (weight of cover 58 kg (fifty eight kilogram) and weight of frame 58 kg (fifty eight kilogram) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge: With Sewer bricks conforming to IS : 4885

Constructing soak pit 1.20x1.20x1.20 m (one point twenty into one point twenty into one point twenty metre) filled with brickbats including S.W. drain pipe 100 mm (one hundred millimetre) diameter and 1.20 m (one point twenty metre) long complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing masonry Chamber 90x90x100 cm (ninty into ninty into one hundred centimetre) inside, inbrick work in cement mortar 1:4 (one cement : four coarse sand) for sluice valve, with C.I. surface box 100 mm (one hundred millimetre) top diameter, 160 mm (one hundred sixty millimetre) bottom diameter and 180 mm (one hundred eighty millimetre) deep (inside) with chained lid and RCC top slab 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size , i/c necessary excavation, foundation concrete 1:5:10 (one cement : five fine sand : ten graded stone aggregate 40 mm (fourty millimetre) nominal size and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12 mm (twelve millimetre) thick, finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and laying 450 mm (four hundred fifty millimetre) dia RCC pipes Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (one cement : two fine sand) including testing of joints etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge

MILAP SINGH THAKUR