SPECIAL REPAIR TO BLDG NO T104 P21 P22 and P26 AT SUNDERBANI UNDER GE NORTH AKHNOOR

Amount

Demolition of stone slabs and tiles of bed bedded and pointed in any mortar or any description or thickness in floors, aprons etc complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) , complete all as specified & directed.

M&L for brickwork with subclass ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 including demolition of existing stone/brick masonary built in cement/cement lime mortar including all quoins arches etc but exlcuding ashlar masonry complete all as specified and directed.

Non skid ceramic coloured jointless tiles 7mm to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm, but not exceeding 0.18 Sqm, in floors over set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles including 15mm thick screed bed in CM (1:4) complete all as specified and as directed by Engineer-in-Charge.

Glazed ceramic tiles tiles, coloured (300x200 mm) x 6 to 7 mm thick on vertical surface such as skirting/dado over & jointed in neat cement slurry & pointed in white or coloured cement to match including 10 mm thick in CM 1:4 rendering other than fair faces finished even and fair to receive tiles complete all as specified and as directed by Engineer-in-Charge.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade or the slab including rubbing and polishing complete including 20mm thick screed bed or bedding layer in CM (1:4) for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

Ditto all as per item No. 7 here-in-above but as in riser of steps ,skirting, dado and pillar including 10 mm thick in CM 1:4 rendering to receive kota stone complete all as specified and as directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof overing/ cladding to wall, fixed with self tapping screws incl ridge including dismantlling of existing asbestos cement (corrugated, semi corrugated) sheets as in roof covering including ridges,hips, valleys and flashings etc complete all as specified & directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof overing/ cladding to wall, fixed with self tapping screws incl ridge complete all as specified & directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm not exc 4.0 Sqm each complete all as specified and directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth (without using extra cement) with using water proofing compound including taking down of existing cement plaster from Brick walls, stone walls etc. including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed by Engineer-in-Charge. (WPC shall be measured and paid separately).

Rendering 15 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth (without using extra cement) including taking down of existing cement plaster from Brick walls, stone walls etc. including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of new treated surfaces of walls and applying two coat of cement base paint complete all as specified and directed.

M&L for Preparation of old treated surfaces of walls and applying one coat of cement base paint complete all as specified and directed.

M&L for Preparation of new treated surfaces of walls and applying two coat of oil bound distemper over one coat of chalk whiting complete all as specified and directed.

Supply only Integral water proofing compound.

Pressed steel frames factory made for doors out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs, hinges, lock strike plate, hinges etc complete, size of frame 125x60mm including tarring ends and back of chowkats and lugs complete all as specified and as directed by Engineer-in-Charge.

PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified

35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge.

35mm thick, 2nd class hard wood glazed and skelton door shutter, open rebated and prepare to receive glass, gauzed etc (without sash bars) edges of framming plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR PART I Section 8 clause 8.24(a) supplied and fitted to chowkhat complete all as specified and as directed by Engineer-in-Charge.

200 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

300 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and directed.

Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

Aluminium handles cast type anodised of size 125 mm long ISI marked complete all as specified and as directed.

Aluminium handles cast type anodised of size 150 mm long ISI marked complete all as specified and as directed.

Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified.

All as per item No 28 here-in-above but without glazing bars.

S&F Mild steel framed work as in grills, grating etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, conforming to Fe-290 Gde-E-165, complete all as specified

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each complete all as specified and directed.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

Preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, and painting with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old untreated wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, and painting with one coat of synthetic enamel paint over existing surface complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for Preparation of old steel and iron surfaces of any description, over 10 cm width of girth, not otherwise described and applying one coat (finishing coat) of synthetic enamel paint all as specified and directed.

Rolled mild steel section as in main and cross beams, hip and jack,rafters, purlins, where connected to common, rafters and running rails and guiders for sliding doors: fixed with angle cleats or other connecting plates conforming to grade Fe 410-W (Gde E-250) quality 'A' complete all as specified & directed by Engineer-in-Charge.

S&F rolled mild steel plates (plain or chequerred) channels square cut or notched (ordinary and counter sunk) forming holes without any attachment complete all as specified and as directed by Engineer-in-Charge.

Cutting opening through walls for door, window and other opening etc cutting out defective masonry for underpinning incl providing fixing nad removing , cleaning and removing surplus to store and rubbish off the premises. all as spd & directed

Taking up or down 15mm steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

S&F 15 mm GI tube medium grade ISI marked galvanised with all necessary fittings and fixed complete to wall, ceiling or laid in floors complete all as specified and as directed by Engineer-in-Charge.

Fixing only 15mm GI tubing and connection in new or old position(walls, ceiling and floors etc) including all fittings all as specified and directed.

Taking up or down 20mm steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

S&F 20 mm GI tube medium grade ISI marked galvanised with all necessary fittings and fixed complete to wall, ceiling or laid in floors complete all as specified and as directed by Engineer-in-Charge.

Fixing only 20mm GI tubing and connection in new or old position(walls, ceiling and floors etc) including all fittings all as specified and directed.

S&F in repair Bib taps, cast copper alloy, fancy type chromium plated with long body crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, complete all as specified and directed by Engineer-in-Charge.

GI frame work 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soft it at approx x 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 centre to centre including 4 mm thick designer building board in grid fixed in position alongwith applying three coat of white wash on board including dismantling of existing wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs /blankets any thickness including cover fillets complete all as specified and directed by Engineer-in-Charge.

Mild steel springs for doors, 150 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engineer-in-Charge.

50 mm thick 75 cm wide PCC type C-1 1:3:6 (using 20mm graded stone aggregate) as in plinth protection laid in bays complete including 75mm thick consolidated hard core of broken stone over rammed earth finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge. Note :- The rate quoted shall be deemed to include for use and waste of form work / screed strips and to divide the area in panels.

M&L for chequerred cement concrete colour tiles 30 cm x 30 cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors including 20mm thick screed bed in CM (1:6) over 75mm thick PCC 1:3:6 type C-2 (using 40mm crushed stone aggregate) as in sub sub base under tiles complete all as specified and as directed by Engineer-in-Charge.

M&L for 50mm thick PCC type B1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in floors all as specified .

Non skid ceramic coloured jointless tiles 7mm to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm, but not exceeding 0.11 Sqm, in floors over set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for 5mm thick cement plaster in CM 1:4 on ceiling other than fair face, finish over complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of newly plastered or previously untreated wall surfaces and applying three coats of white wash complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2010 as specified and as directed by Engineer-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2010 as specified and as directed by Engineer-in-Charge.

Steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous china half stall type urinal white (excluding flushing cistern) including spreader waste pipe and flush pipe complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Vitreous china wash basin, white, flat back, size 550x400mm including tap, waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern waste pipe and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc, complete all as specified and as directed by Engineer-in-Charge.

S&F in repair PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets and PVC bend pipe 90 cm long 32mm dia, complete all as specified and as directed by Engineer-in-Charge.

S&F PVC floor traps 75mm dia with grating including jointing with solvent cement complete all as specified and directed.

S&F Salt-glazed stoneware gully traps, square or round mouthed, type 'P' of size 150mmx150mm complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and as directed by Engineer -in-Charge.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down/dismantling existing water tank complete all as specified and directed by Engineer-in-Charge.

S&F Stop valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, complete all as specified and directed by Engineer-in-Charge.

S&F Stop valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 20 mm, complete all as specified and directed by Engineer-in-Charge.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

M&L for Point wiring with 1100 volts grade multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm (phase -Red, Neutral-Black) drawn into and including surface rigid non metallic PVC casing and caping medium grade 'ISI marked' of 20/30mm size as required ivory colour, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick phenolic laminated white sheet cover complete with all accessories, fixing arrangements on wall /roof/floor by means of drilling by heavy duty hand drill and fixing with PVC rawl plug and screws including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch, complete all as specified & directed by Engineer-in-Charge.

All as per Srl item No. 70 here-in-above but for one 3/5 pin 6 Amps socket outlet on same board with other switches.

All as per Srl item No. 70 here-in-above but for one 3/5 pin 6 Amps socket outlet on independent board.

M&L for Point wiring with 1100 volts multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 2.5 Sqmm (phase-red, Neutral-Black) drawn into and including PVC casing and caping 'ISI marked' of 20/30mm size ivory colour as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick phenolic laminated sheet cover complete with all accessories, fixing arrangements on wall /roof/floor by means of drilling by heavy duty hand drill and fixing with PVC rawl plug and screws including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 16 Amps controlled by one switch on independent board, complete all as specified & directed. Notes for Srl Item No. 70 to 73 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

S&F angle holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

Switch piano flush type 6 Amps 240 Volt, single pole one way, complete all as specified & directed.

Switch piano flush type 16 Amps 240 Volt, single pole one way, complete all as specified & directed.

Socket outlet 2 in 1, 3 pin type, 6 & 16 Amp, flush type, complete all as specified & directed.

Socket socket combination outlet 2 in 1, 2 & 3 pin type, 6 Amp, flush type, complete all as specified & directed.

Socket outlet 2 in 1, 2 & 3 pin type, 6 Amp, flush type, complete all as specified & directed.

S&F MCB distribution board SPN, 240 volts, 8 way powder coated, CRCA steel sheet constructed as per IS:8623, degree of protection IP 43-IK 09 with metal door, recess mounted, having insulated 100amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaced as required including taking down existing MCB distribution board with incoming outgoing control any capacity complete all as specified and directed by Engineer-In-Charge.

S&F MCB distribution board SPN, 240 volts, 4 way powder coated, CRCA steel sheet constructed as per IS:8623, degree of protection IP 43-IK 09 with metal door, recess mounted, having insulated 100amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaced as required including taking down existing MCB distribution board with incoming outgoing control any capacity complete all as specified and directed by Engineer-In-Charge.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete all as specified & directed.

S&F Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 mtr below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) including taking down old existing earthing complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

S&F exhaust fan copper wound heavy duty AC single phase 230/240 volts of size 300mm complete all as specified and directed by Engineer-in-Charge.

S&F Surface & wall mounted, LED tube light fitting, 20/22W, decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified & directed. Make. Havells, Cat Part No. LHEXBLP7PN1W020 or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska LED/ GE Lighting/ Surya

S&F Energy saving 10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length, 230v, 50Hz complete all as specified & directed. Make. Havells, Cat Part No. RUGBYNEONFT10WLED760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

S&F MCB, single pole, (SP) 6 to 32 Amp, AC, 10 KA repturing capacity, ISI marked, 240 Volt, 'B' series, including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified & directed by Engineer-in-Charge.

S&F MCB, single pole & neutral, (SPN) 10 to 32 Amp, AC, 10 KA repturing capacity, ISI marked 240 Volt, 'B' series, including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified & directed.

S&F LED bulb 12 watt complete all as specified and directed.

Supply, laying and testing XLPE insulated, electric cable (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 core connected with suitable cable gland and aluminium lugs, laid in trenches or passing through pipes including taking down old existing unserviceable cable complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m deep in soft/loose soil for laying of underground cable, foundation of poles & stays etc., and getting out, complete all as specified & directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed by Engineer-in-Charge.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

M&L for 25mm bore Tubes, 'light grade', galvanised, with all fitting; laid in trenches for passing of XLPE cable complete all as specified and directed.

M/s Mool Raj Romesh Chander

M/S K K ENTERPRISES