SPL REPAIR TO OTM ACCN NO. P-23 AT NAGTALAO UNDER GE BANAR

Amount

Demolition of Cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level) and removing debris out of MOD land complete all as specified and directed by Engr-in-Charge .

Demolition of Cement concrete in any description and any position not otherwise specifically provided for and removing debris out of MOD land complete all as specified and directed by Engr-in-Charge .

M&L for 25 mm thick cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) to receive floor finishes etc complete all as specified and directed by Engr-in-Charge .

Demolition of RCC in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work if cement concrete is reinforced (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engr-in-Charge .

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-Charge .

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge .

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15 mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge .

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge .

M&L for coloured glazed ceramic tiles 300mmx450mmx6mmthick as per IS 13712 Grade II(a) over 15mm thick rendering in CM (1:6) set and jointed in neat cement slurry and pointed with colour cement to match on vertical surfaces as in dado (colour and pattern as approved by GE) complete all as specified and directed by Engr-in-Charge .

M&L for Non skid Ceramic tiles 7 to 8 mm thick (white), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed by Engr-in-Charge .

Taking down cement or cement lime plaster,any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed by Engr-in-Charge .

M&L for 10 mm thick rendering in CM 1:6 on stone masonry finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge .

M&L Rendering 10 mm thick in CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified and directed by Engr-in-Charge .

Preparing new surfaces plastered or unplastered on ceiling complete all as specified and directed by Engr-in-Charge .

M&L for 10 mm thick rendering in CM 1:4 on stone masonry finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge .

M&L for three coats of white wash of new surfaces on walls complete all as specified and directed by Engr-in-Charge .

M&L for three coats of white wash of new surfaces as on ceilings complete all as specified and directed by Engr-in-Charge .

M&L for two coat of oil bound distemper on plastered or unplastered on wall with distemper oil emulsion, white or tinted complete all as specified and directed by Engr-in-Charge .

Preparing new surfaces plastered or unplastered on wall complete all as specified and directed by Engr-in-Charge .

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over any type of surface complete all as specified and directed by Engr-in-Charge .

Taking down chowkat with shutters (without taking off shutter from frame) size area n.exc 1.50 sqm each complete all as specified and directed by Engr-in-Charge .

Taking down chowkat with shutters (without taking off shutter from frame) size area exc 1.5sqm but n.exc 4.0 sqm each complete all as specified and directed by Engr-in-Charge .

S&F PVC door frame wooden finish of size 50mmx 47mm of 5mm plain color PVC sheet reinforced with MS square tube complete all as specified and directed by Engr-in-Charge .

Taking down of window and ventilators of any description complete all as specified and directed by Engr-in-Charge .

M & L for 35mm thick flush shutters, solid core construction with block board core and veener face fixed on both side of door, coloured as approved by GE, complete all as specified and directed by Engr-in-Charge .

S & F 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed by Engr-in-Charge .

S&F power coated Anodised aluminium window and ventilator shutters(Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as per drg No CEJZ/TD/62/2015 Sh 1/1 & CEJZ/TD/63 Sh 1/3 to Sh 3/3 complete all as specified and directed by Engr-in-Charge. Note:- Grill, glass & wire cloth shall be measured & paid separately.

S&F Anodised aluminium powder coated decogrill for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr-in-Charge .

S&F 5.5mm thick Sheet glass ordinary quality with solar control film of 25 micron reflective type sticked with glass as per manufacturer instuction and glazing with necessary rubber packing in square in any size in each pane complete all as specified and directed by Engr-in-Charge .

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge .

M/L for two coat of synthetic enamel paint over a coat of pink primer on new wooden surface including preparation of surface, over 10Cm width or girth complete all as specified and directed by Engr-in-Charge .

S&F factory PVC moulded shutter of 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed by Engr-in-charge.

S &F of Stainless steel butt hinges medium weight, cold rolled of size 100 mm size complete all as specified and directed by Engr-in-Charge .

S&F 150 mm long aluminium anodised tower bolt complete all as specified and directed by Engr-in-Charge .

S&F 150mm long aluminium anodised handle extruded section complete all as specified and directed by Engr-in-Charge .

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge .

Taking up or down GI steel water tubing 15 mm bore and connection, including cleaning for refixing or remove to site complete all as specified and directed by Engr-in-Charge .

Taking up or down GI tubing 20 mm bore and connection, including cleaning for refixing or remove to site complete all as specified and directed by Engr-in-Charge .

Supply & Fixing 15mm bore GI Tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge .

Supply & Fixing 20mm bore GI Tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge .

S&F in repair of bib cock 15mm dia, Chromium Plated cast copper alloy fancy type, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge .

S&F in repair Fancy type Chromium plated shower roses 125mm size with arm, with or without swivel joints, 15mm bore, including fixing to steel pipe or union complete all as specified and directed by Engr-in-Charge .

S&F in repairs angular stop valves cast copper alloy chromium plated(ISI marked) screwed down high pressure fancy type screwed both ends for 15mm bore of iron pipe or union complete all as specified and directed by Engr-in-Charge .

S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified and directed by Engr-in-Charge .

M&L for 75mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate complete all as specified and directed by Engr-in-Charge .

S&F in repair tubular towel rail 20mm dia brass chromium plated `D' type 60cm long with bracket and fixed complete all as specified and directed by Engr-in-Charge .

S&F in repair vitreous china squatting Pan, Orissa Pattern of size 580X440mm white with integral foot rests and cast iron `P' or `S' trap front or back Including connection to trap etc and provision of cement concrete bedding and good to floor complete all as specified and directed by Engr-in-Charge .

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)and cast iron `P' or `S' trap front or back Including connection to trap etc and provision of cement concrete bedding and good to floor complete all as specified and directed by Engr-in-Charge .

Dismantling of cast iron/pvc soil waste & vent pipes 100/110 mm dia incl all fittings etc complete all as specified and directed by Engr-in-Charge .

Dismentaling of cast iron/pvc soil waste & vent pipes 75 mm dia incl all fittings etc complete all as specified and directed by Engr-in-Charge .

Supplying and laying of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches complete all as specified and directed by Engr-in-Charge .

Supplying and laying of 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches complete all as specified and directed by Engr-in-Charge .

Supplying and laying of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid on walls / ceiling or laying in floors complete all as specified and directed by Engr-in-Charge .

Supplying and laying of 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid on walls / ceiling or laying in floors complete all as specified and directed by Engr-in-Charge .

S&F 75 mm bore PVC (SWR) bends any radius with oval acess door complete all as specified and directed by Engr-in-Charge .

S&F 110 mm bore PVC (SWR) bends any radius with oval acess door complete all as specified and directed by Engr-in-Charge .

S&F for 100mm dia PVC (SWR) cowls, diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engr-in-Charge .

S&F 110 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by Engr-in-Charge .

S&F 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by Engr-in-Charge .

S&F 110 mm PVC (SWR) reducers complete all as specified and directed by Engr-in-Charge .

S&F 75 mm PVC (SWR) reducers complete all as specified and directed by Engr-in-Charge .

Supply and fixing in repair PVC valve less symphonic action type flushing cistern 10 ltrs capacity low level with inlet, ball valve, float and handle Including bracket and flush pipe fixed and complete all as specified and directed by Engr-in-Charge .

S&F 32mm bore low or high density polyethylene waste pipes (LDPE) of pressure rating 6Kg/Sqm fixed complete to walls, ceiling or floors etc complete all as specified and directed by Engr-in-Charge .

S&F in repair 15mm bore PVC connection 600mm long best quality with PTMT nuts complete all as specified and directed by Engr-in-Charge .

S&F in repair 15mm bore PVC connection 750mm long best quality with PTMT nuts complete all as specified and directed by Engr-in-Charge .

M&L 75 mm thick Type C-2(1:3:6)( using 40mm graded stone aggregate) as in plinth protection finished complete including forming joints in 2 mtr interval and filled with bitumen mastic complete all as specified and directed by Engr-in-Charge .

Taking down existing roof treatment in any postion and any thickness on RCC roof slab and debries to be disposed out of MOD land complete all as specified and directed by Engr-in-Charge .

M&L for roof treatement in the following stages :-(a) Applying evenly a coat of bituminous primer conforming to IS-3384 @ 0.40 ltr per sqm over and including 10 mm thick cement mortoar (1:4) and surfaces finished even and smooth without using extra cement all as specified . (b) Second coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg/Sqm . (c) Third layer of APP modified polmeric membrane centre core of 20 micron HMHDPE outer film 20 micron both sides, thickness 1.5 mm having weight 2.25 Kg/Sqm. (d) Fourth coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg per Sqm. (e) 40mm thick PCC padding in cement concrete 1:2:4 (12.5 mm graded aggregate finishing even and smooth and cutting V joints @ 120 cm bothways and filling with bitumen 85/25 @1.2 kg/Sqm complete all as specified and directed by Engr-in-Charge .

M&L for Treatment of sunken portion is as follows:- (i) demolition of lean concrete and other type of filling in sunken portion & cleaned portion incl vertical wall surface complete as directed (ii) M&L for providing 12 mm dia holes of 40 mm deep @2.00 mm c/c at junction of beams and columns as co-ordial points for inserting /pouring cement slurry by pressure grouting for sunken floors of toilet , including sealing the hole with CM 1:3,all specified and as directed by EIC. (iii)M&L for water proofing for sunken portion in CM 1:3,20 mm thick two coats with water proofing compound at rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement .(WPC to be measured and paid separately) (iv)M&L for apply in evenly two coats of industrial bitumen 85/25 at rate of 1.20kg/sqm (v)M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in filling (sunken portion),etc. (vi)M&L for PCC1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @2% by wt of cement as sub base, 75 mm thick. .(WPC will be measured and paid separately) on top (vii)M&L for plastering in CM 1:4, 15 mm thick with water proofing compound at rate of 2% by weight of cement and finishing the surface even and fair.(WPC will be measured and paid separately)(screed bed to recieve ) Note:- Above includes(a) Test again of water tightness by pounding for 72 hrs & rectify defects if any till total elimination of defect (b) The sunken portion shall be tested for leakage /seepage/dampness by pounding with water for 72 hours . in case of any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical &tested again.The process of grouting and testing shall be repeated till leakage /seepage/dampness is eliminated (c) Horizontal flat area to be measured complete all as specified and directed by Engr-in-Charge .

S&F in replacement rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) white, hoisted and fixed in position all as directed of capacity 1000 ltrs a Including 20mm bore brass ball valve high pressure with polythene float complete all as specified and directed by Engr-in-Charge .

Supply only integral water proofing compound (ISI marked) complete all as specified and directed by Engr-in-Charge .

Demolition of stone masonry /block walling built in cement mortar complete all as specified and directed by Engr-in-Charge .

M&L for squarred rubble walling Jodhpur type regular coursed well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge .

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified and directed by Engr-in-Charge .

Taking down carefully cement conc /spalled out concrete from RCC roof projections, ceiling ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc complete all as specified and directed by Engr-in-Charge .

M&L for MS 12 mm dia TMT bars by way of stitching ( welding ot tieing with existing reinf) incl drilling holes etc & securing ends in walls etc complete all as specified and directed by Engr-in-Charge .

M&L for cleaning the existing reinf of slabs , chajjas etc & applying a coat of SIKA RUSTOFF 11 to remove the loose rust particles etc & throughly cleaning the surface complete all as specified and directed by Engr-in-Charge .

M&L for applying a coat of bond coat with cement slurry (1 part cement to 1.5 -2 parts water) mixed with admixture LATEX POWER mixed @5 Kg per 50 kg of cement & applying to the conc surfaces @ 200 gm/sqm to obtain tack complete all as specified and directed by Engr-in-Charge .

M&L for 15 -20 mm thick rendering in CM 1:1:2 using1 part of cement 1 part 2-3 mm screenings of stone agg & 2 parts coarse sand ofover the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPER admixture @ 100 gm /50kg of cement & finishing the surface even & rough to receive final rendering coat complete all as specified and directed by Engr-in-Charge .

M&L for 5 mm thick rendering in CM 1:3 & finishing the surface even & smooth w/o using extra cement complete all as specified and directed by Engr-in-Charge .

M&L for 10-15 mm thick rendering in CM 1:3 over the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPER admixture @ 100 gm /50kg of cement & finishing the surface even & smooth complete all as specified and directed by Engr-in-Charge .

S&F CP brass Soap Dish as per sample complete all as specified and directed by Engr-in-Charge .

Writing letters or figures (Black Roman, Italic or Indian n. exc 30cm high with thick paint complete all as specified and directed by Engr-in-Charge .

Excavation in trenches not exc 1.50m wide and not exc 1.50m depth and getting out in soft/loose soil ext complete all as specified and directed by Engr -in- Charge.

S&F 150mm Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed by Engr-in-Charge .

M&L for cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate bed to drain pipe 150 mm dia including packing under and hunching against the pipe after they are laid including necessary formwork complete all as specified and directed by Engr-in-Charge .

M&L for Machine Cut Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. complete all as specified and directed by Engr-in-Charge .

Returning, filing in including, levelling,watering and well ramming in layers not exc 25cm thick each complete all as specified and directed by Engr-in-Charge .

Removing excavated material to a distance not exc 50m depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed by Engr -in- Charge.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge .

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed by Engr-in-Charge .

S&F in repair of Vitreous China wash basin size 450 x 300mm, white, flat back, including 32 mm CP waste coupling, waste pipe, PVC Connection 450 mm long, brackets complete all as specified and directed by Engr-in-Charge .

S&F in repair 15 mm Stop valves, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge .

S&F MS chromium plated peg set of five fixing with wall complete all as specified and directed by Engr-in-Charge .

S&F Pillar taps 15mm bore , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge .

Excavating in soft/loose soil in over areas, n exc 1.5 m deep and getting out incl removal n exc 50 m complete all as specified and directed by Engr-in-Charge .

Demolition of Cement concrete in ground floors and pavings exc 15 cm thickness above ground floors and removing debris out of MOD land complete all as specified and directed by Engr-in-Charge .

M&L 100 mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base of flooring complete all as specified and directed by Engr-in-Charge .

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and directed by Engr-in-Charge .

Providing and laying at or near ground level factory of kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including drainage opening wherever required complete all as specified and directed by Engr-in-Charge .

M&L for 25 mm thick sand cushioning / filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-Charge .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, sockets, lamp holder and conduit etc. removing materials to store for taking credit and good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-Charge . Note:- The damaged surfaces to be good with plastering & applying colour wash in required coats to matching with existing surfaces as directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible.

Taking down old DBs ,Sheet metal enclosures (including MCBs) complete, including fixture and fittings removing materials to store for taking credit and good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-Charge . Note:- The damaged surfaces to be good with plastering & applying colour wash in required coats to matching with existing surfaces as directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible.

Taking down old light fittings of any type and capacity complete, including fixture and fittings removing materials to store for taking credit and good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-Charge .

Taking down old submain wiring of any type and capacity complete, including fixture and fittings removing materials to store for taking credit and good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-Charge .

Taking down old rusted earthing complete, including fixture and fittings removing materials to store for taking credit complete all as specified and directed by Engr-in-Charge .

M&L for point wiring with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including rigid PVC CONDUIT and conduit accessories,confirming to IS specifications,concealed in wall fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing ,complete all as specified and directed by Engr-in-Charge for :-

(a) One light point controlled by one switch.

(b) One fan/ exhaust fan point controlled by one switch.

(c) One switch socket out let point 5 Amps on independent board

(d) One switch socket out let point 5 Amps on same board

Ditto all as per item No.108 herein before but with 4 sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified and directed by Engr-in-Charge .

Supply and fixing switch piano flush type 5 Amp single pole, one way complete all as specified and directed by Engr-in-Charge .

Supply and fixing for ceiling rose surface bakelite 65 x 50 mm three terminal complete all as specified and directed by Engr-in-Charge .

Supply and fixing socket outlet 5 pin 5 Amps, flush type complete all as specified and directed by Engr-in-Charge .

Supply and fixing switch-Socket outlet combination 2 in 1 3 pin 6 and 16 amp flush type universal complete all as specified and directed by Engr-in-Charge .

Supply and fixing switch- Socket outlet combination 2 in 1 3 pin 6 flush type universal complete all as specified and directed by Engr-in-Charge .

Supply and fixing lamp holder PVC/polycarbonate type with cord grip cap suitable for pendant fitting complete all as specified and directed by Engr-in-Charge .

S&F powder coated sheet metal enclosures MCCB VTPN DB, double door, tripple pole and neutral, 6 way 415 volts fitted with insulated vertical phase bus bar/neutral bar of capacity 125 A with shround earth bar cement spill proctector interconnecting wire set cable tiesblanking plates and circuit indentificationlables etc all as per IS-8623-1 IK-09 and good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified and directed by Engr-in-Charge .

Supply and fixing MCCB 415V,16KA, 4 Pole 100 Amps Adjustable overload setting & fixed magnetic setting, good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified and directed by Engr-in-Charge .

Supply and fixing MCB SPN 40 Amps 240 volts complete all as specified and directed by Engr-in-Charge .

Supply and fixing powder coated sheet metal enclosures DB, double door, single pole and neutral 12 way 240 Volt fitted with bus bar, DIN channel, neutral link and incoming contact and good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified and directed by Engr-in-Charge .

Supply and fixing MCB SPN 32 Amps 240 volts complete all as specified and directed by Engr-in-Charge .

Supply and fixing MCB SP 6 Amps to 32 Amps 230 Volt complete all as specified and directed by Engr-in-Charge .

Supply and fixing MCB SP 40 Amps 230 Volt complete all as specified and directed by Engr-in-Charge .

S&F surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x22 Watt,(4 feet) fixed properly on wall surface and connecting complete from ceilling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified and directed by Engr-in-Charge .

S&F building security light LED fitting 35 watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant , epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 35 watt, fixed / connect properly at directed location on building with IP 65/66 protection complete all as specified and directed by Engr-in-Charge .

Taking down old bracket and Supply and fixing bracket for street light fittings of any size of GI pipe medium grade 32 mm dia 1.25 mtr length bend to required size and shape including provision of clamps and fittings in position and two coat of aluminum paint over a coat of red oxide primer all as specified and directed including taking down old bracket complete all as specified and directed by Engr-in-Charge .

Taking down Old Ceiling fan, transport to workshop, removing burned motor winding and rewinding the motor using enameled copper wire of suitable gauge with Class F or H insulation, replacing old capacitor with a new one of matching rating, applying enamel-based paint on the ceiling fan for durability, and refixing on the existing location, complete all as specified and directed by Engr-in-Charge .

Taking down Old Exhaust fan transport to workshop, removing burned motor winding and rewinding the motor using enameled copper wire of suitable gaugewith Class F or H insulation, replacing old capacitor with a new one of matching rating, applying enamel-based paint on the ceiling fan for durability, and refixing on the existing location, complete all as specified and directed by Engr-in-Charge .

M & L for Sub main wiring complete with three single core 4.0 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 4.0 sqmm in and including PVC casing caping and accessories complete all as specified and directed by Engr-in-Charge . (Note:- (i) Good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 4.00 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

M & L for Sub main wiring complete with three single core 6.0 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 6.0 sqmm in and including PVC casing caping and accessories complete all as specified and directed by Engr-in-Charge . (Note:- (i) Good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 6.00 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

M & L for building earthing complete with galvanised steel earth plate electrode 60 x 60x 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level, connected to galavanised iron earth lead by means of bolt, nut, check nut and washer of galavanised iron wire 4mm as earthing lead as shown in Electrical Plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in hard/dence soil, earth pit in PCC 1:3:6 type C1 using 20mm stone aggreate, funnel, 20mm dia GI medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs, wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not excessding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part I 2009 complete all as specified and directed by Engr-in-Charge .

M/s Anand Construction Company (BID ID -3288223)

M/s Vishaka Enterprises (BID ID -3285814)