BID DOCUMENT FOR DEVELOPMENT WORK OF ICONIC ROAD FROM LAL DARWAJA ROAD TO PANCHAVATI CIRCLE (GAURAV PATH) AT KHAMBHAT NAGARPALIKA UNDER: SWARNIM JAYANTI MUKHYA MANTRI SAHERI VIKAS YOJANA (OUT GROUTH) GRANT. YEAR: 2025-26.

Sr. No. Description Amount

1 CONSTRUCTION OF ASPHALT ROAD WIDENING AT LAL DARWAJA Rs.

ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE).

2 CONSTRUCTION WORK OF PAVER BLOCK & KERBING AT LAL Rs.

DARWAJA ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR

3 CONSTRUCTION WORK OF DIVIDER & M.S.PEDISTRAL FOR Rs.

SCULPTURE LAL DARWAJA ROAD TO PANCHAVATI CIRCLE

(GAYATRI NAGAR CHOKE).

4 3D WALL PAINTING , PLANTATION & DECORATIVE LIGHT AT LAL Rs.

DARWAJA ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR

5 SUPPLYING, ERECTING & COMMISSIONING OF STREET LIGHT Rs.

WITH LED FROM LAL DARWAJA ROAD TO PANCHAVATI CIRCLE

(GAYATRI NAGAR CHOKE). (ROAD LENGTH 700 RMT.00 (15 RMT

6 PROPOSED R.C.C BENCHES AT LAL DARWAJA ROAD TO Rs.

PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE).

7 LED SCREENS AT LAL DARWAJA ROAD TO PANCHAVATI CIRCLE Rs.

(GAYATRI NAGAR CHOKE) (2 Nos.)

8 ROAD FURNITURE AT LAL DARWAJA ROAD TO PANCHAVATI Rs.

CIRCLE (GAYATRI NAGAR CHOKE).

9 PROVIDING ELECTRIFICATION INSTALLATION IN ENTRANCE GATE Rs.

FROM LAL DARWAJA TO PANCHAVATI CIRCLE ( GAYATRI NAGAR

SECTION-7 BILL OF QUANTITIES-307

10 SUPPLYING & ERECTING OF 12 METER HIGH MAST POLE WITH Rs.

LED FIXTURES AT ICONIC ROAD ATLAL DARWAJA ROAD TO

PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE).

11 PROPOSED CIRCLE DEVELOPMENT OF LALDARVAJA CIRCLE FOR Rs.

I / We am/are willing to carry out the work at _____________ % above / below (percent should be

written in figure and in words) of the estimated rates mentioned above. Amount of my/our tender

works out as under.

( In words ) _________________________ percentage above / below the estimated rate.

Estimated Amount put to tender Rs.

Deduct _______ % below Rs. Rs.

Estimated Amount put to tender Rs.

Add _______ % above Rs. Rs.

Total Amount Rs.

Total Amount Rs.

*( Please strike out whichever is not applicable)

Note :1 All work shall be carried out as per Public Works Department Hand Book and other specifications of

Division or as directed.

Note :2 Rates quoted include clearance of site (prior commencement of work and its close) in all respects and

hold good for work under.

Note : 3 I/ We have read the conditions mentioned in this tender and agree to abide by the same.

Note : 4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items

where there is a change as per actual mix design the cost of difference of cement consumption have been

deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Signature of Contractor President Chief Officer

Khambhat Nagarpalika Khambhat Nagarpalika

Khambhat Khambhat

SECTION-7 BILL OF QUANTITIES-308

KHAMBHAT NAGARPALIKA KHAMBHAT

NAME OF WORK:- CONSTRUCTION OF ASPHALT ROAD WIDENING AT LAL DARWAJA ROAD TO PANCHAVATI

CIRCLE (GAYATRI NAGAR CHOKE) , AT:KHAMBHAT.

Sr. Qauntity Item Total Unit Amount

1 15370.00 Preparing surface by Brushing with wire brushes for

Smt removing caked mud etc. Air compressor / sweeping

with brooms and finally fanning the cleaned surface

with gunney bags to remove all loose dirt etc.(2) Black

top/ CC surface. 17.88 Smt

2 1269.00 Providing and Laying 37.50mm thick Bituminous

M.T. Macadam with B.T. aggregate as Per MORT & H.

specification & asphalt for tack coat @ 2.50 Kg./10 Smt.

with Mechanical Sprayer & Bitumen Grade 80/100 for

mixing @ 34.00 Kg./M.T. i.e., 3.40 % of total weight of

mix including heating the aggregate & asphalt in

continous batching drum mix plant and spreading the

same by paver finisher & consolidation with vibratory

roller including providing all materials equipments,

tools & plants, fire wood, oil, kerosene, labour charges

etc. complete using contractor's own machinery drum

mix plant & paver finisher etc. complete.

3 884.00 Providing and Laying 25mm thick S.D.B.C. with B.T

M.T. Aggregate as per M.O.R.T and H. specificaton and (VG

30) asphalt grade 60/70 mixing at 50 kg/M.T. i.e. 5.0%

by weight of total mix incuing heating the aggregate

and asphalt in continous batching drum mix plant and

spreading the same by paver finisher and consolidation

with vibratory rollar including providing all materials

equipments, tols and plants, fire wood, oil, kerosene,

labour charges etc. complete using contractor own

machinary drum mix plant and paver finisher etc.

4 15370.00 Providing and laying Bituminous Painting spreading hot

Smt asphalt at the rate of 5 Kg./10 Smt. and spreading

flushing sand or stone dust at the rate of 0.15 Cmt./10

Smt. rate including all cost of sand, equipment T & P

firewood, oil, kerosene, labour charges etc. complete

by using contractor's own machineries.

SBD SECTION-7 BILL OF QUANTITIES-309

4 705.00 Supplying and fixing reinforced concrete heavy duty

Rmt non-pressure pipes with collars for culverts carrying

heavy traffic as per IS 458-1991 specifications including

setting the pipes in C.M. 1:2 watering and laying (to

level or slopes) of class NP3 of following internal

daimeters.(ii) 450mm dia.. For Utility Shifting

Add : 18% GST, Charges Rs.

Add : 2% Contingency Charges Rs.

Add : 1% Quality Controll Rs.

SBD SECTION-7 BILL OF QUANTITIES-310

KHAMBHAT NAGARPALIKA KHAMBHAT

CONSTRUCTION WORK OF PAVER BLOCK & KERBING AT LAL DARWAJA ROAD TO

PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE),AT KHAMBHAT.

Qty. Description Unit Amount

1 805.00 Excavation for foundation in Loose or soft soil

Cmt. 1:5 mt. Depth including sorting out and

stacking of useful materials and depositing of

the excavated stuff for all the leads and lift

etc. complete as directed by Engineer-in-

a) 0.00 to 1.50 M. depth 122.94 Cmt.

2 388.50 Providing and laying P.C.C. (1:4:8) mix (1

Cmt. cement, 4 coarse sand, 8 hand broken stone

aggregate of 40mm nominal size) for

foundation in true line and level including

ramming, compacting by excluding cost of

work etc. complete as directed by Engineer-in-

3 2800.00 Providing and fixing pre-cast concrete kerb

Rmt stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of

M200 grade concret as per approved design

and including excavation for fixing in proper

line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

For Kerbing 404.21 Rmt

SBD SECTION-7 BILL OF QUANTITIES-311

4 3885.00 Providing and fixing pre-cast Rubber Dye inter

Smt locking concrete block 60mm thick with grade

of concrete M300 pnumatic compressed by

mechanically pressed and as per approved

design including 75mm Sand layer for

levelling and filling the joint with sand in

proper line and level etc complete.

Add : 18% GST, Charges Rs.

Add : 2% Contingency Charges Rs.

Add : 1% Quality Controll Rs.

SBD SECTION-7 BILL OF QUANTITIES-312

KHAMBHAT MUNICIPALITY, KHAMBHAT

CONSTRUCTION WORK OF DIVIDER & M.S.PEDISTRAL FOR SCULPTUREAT LAL

DARWAJA ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE), AT KHAMBHAT .

Qty. Description Unit Amount

1 108.00 Excavation for foundation in Loose or

Cmt. soft soil 1:5 mt. Depth including sorting

out and stacking of useful materials and

depositing of the excavated stuff for all

the leads and lift etc. complete as

directed by Engineer-in-charge.

a) 0.00 to 1.50 M. depth 125.86 Cmt.

2 36.00 Providing and laying cement concrete

Cmt. 1:4:8 (1- Cement : 4- coarse sand : 8-

hand broken stone aggregates 40 mm

nominal size) and curing complete

excluding cost of formwork in (A)

Foundation and Plinth 2679.92 Cmt.

3 Providing and laying controlled cement

concrete M-200 and curing complete

excluding the cost of formwork and

reinforcement of reinforced concrete

a. 162.00 -- do -- for R.C.C Vertical Wall 4511.61 Cmt.

b. 9.50 -- do -- for Post for Sculpture 4590.39 Cmt.

4 8560.00 Providing TMT Bar FE 500D

Kgs. reinforcement for R.C.C. work including

bending, binding and placing in position

complete upto floor two level

SBD SECTION-7 BILL OF QUANTITIES-313

5 2160.00 Providing Formwork of ordinary timber

Smt. plankings so as to give a rough finished

including centering, shuttering, struting

and propping etc. height of propping and

centering below supporting floor to

ceiling not exceeding 4.0 Mt. and

removal of the same for cast in situ

reinforced concrete and plain concrete

For Vertical Wall 249.67 Smt.

6 2076.00 Providing and applying 10 mm thick

Smt. smooth cement plaster in single coat of

fair side of brick/concrete walls for

interior plastering for G.F. upto floor two

level in C.M.(1:3) (1 cement, 3 sand)

including finishing even and smooth with

floating coat of neat cement slurry

including scaffolding curing etc.

complete as directed by Engineer-in-

7 1296.00 Painting line, deashes, arrow, letter etc

Smt on road, Air fields and like in two coats

with road marking paint, brushing,

including cleaning the surface of all dirt,

dust and other foreign matter(1) over

10cm width 59.35 Smt

8 294.00 Filling in foundation and plinth with

Smt. murrum or selected soil in layers of

20cm. thickness including watering,

ramming and consolidating etc.

complete. 273.07 Smt

SBD SECTION-7 BILL OF QUANTITIES-314

9 1.00 PLANTING COST OF TREE IN DIVIDER AT

Job ICONIC ROAD

Add : 18% GST, Charges Rs.

Add : 2% Contingency Charges Rs.

Add : 1% Quality Controll Rs.

SBD SECTION-7 BILL OF QUANTITIES-315

KHAMBHAT NAGARPALIKA KHAMBHAT

3D WALL PAINTING , PLANTATION & DECORATIVE LIGHT AT LAL DARWAJA ROAD TO

PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE), AT KHAMBHAT

Item Qty. Description Total Unit Amount

1 1400.00 Providing Artistic 3D wall Painting on Godi road

Smt. Bridge location up to 10 Mtr Height.

2 140.00 Providing Loam or Clay soil of approval quality

3 700.00 Laying out Lawn: After excavating soil upto

Smt. cm depth, preparing soil for planting by

supplying and mixing pepairing soil for planting

by supplying and mixing Farm Yard Manure at

the rate of 5 cu. m. per 100 Sq. Mt. area,

providing and planting suckers of pure dharo (

doob ) grass roughly at 10 cm x 10 cm distance

and maintaining till well established etc

complete ( about 45 days ).

4 280.00 PLANTING TREES AND SHURBS After excavating

Nos. pit of the size 60 cm X 60 cm X 60 cm refilling

with the same by providing and mixing farm yard

manure at the rate of 0.06 cum per pit providing

and planting well grown sapling of specified

variety and maintaining till well established

(about 45 days) complete.

5 750.00 STREET LIGHT BRACKET - Providing,

PER SQ.FT Supplying & Installation Decorative

Bracket With Lighting

Length 2.5 ft PER

SBD SECTION-7 BILL OF QUANTITIES-316

6 240.00 (c) LED Bollard fittings of minimum height

Nos. mm & dia.100mm having polycarbonate

clear/milky diffuser mounted on 3mm thick

aluminium finished powder coated pipe with

base plate 160x160mm with erection by

M8x75mm fastner with required RCC

foundation.IP65 for 9 to 20 watt and above

,surge-4kv cat-III

5 1.00 DAHUA 2MP IP PTZ CAMERA 25X ZOOM UPTO

Job 100 MTR. AS PER DIRECTED BY EIC. 377437.00 Job

Add : 18% GST Rs.

Add : 2% Contingency Charges Rs.

Add : 1% Quality Controll Rs.

SBD SECTION-7 BILL OF QUANTITIES-317

KHAMBHAT NAGARPALIKA KHAMBHAT

ESTIMATE FOR R.C.C BENCHES & S.S. DUSTBIN AT LAL DARWAJA ROAD TO PANCHAVATI CIRCLE

(GAYATRI NAGAR CHOKE) , AT KHAMBHAT.

Sr. Item Qauntity Total Rate Per Amount

1 Pre-cast Concrete Reinforced Bench . As 40.00 8080.00 No.

Per Directed Engi. In Charge excluding

Labour, Transpotation & All Taxes. Etc

Add : 5% of Transportation Charge Rs.

Add : 18% of GST Rs.

SBD SECTION-7 BILL OF QUANTITIES-318

KHAMBHAT NAGARPALIKA - KHAMBHAT

NIRMAL GUJARAT 2.0 (ICONIC ROAD)

PROVIDING, ERECTING & INSTALLATION OF STREET LIGHT POLES

LOCATION : DEVELOPMENT WORK OF ICONIC ROAD AT LAL DARWAJA ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR

CHOKE) , AT DAHOD

Item No. & Description Qty. Unit Rate Per Amount

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm

or required depth for laying any size of cable or locating the fault all

over the run and back filling the same and making the surface as

Total 700.00 Mtr. 75.75 Mtr.

(B) If additional machinery like hammer driller or JCB use [Add]

Total 200.00 Mtr. 357.54 Mtr.

Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth in existing

trench for laying of cable. below ground / road surface for enclosing

(A)50 mm outer dia

Total 700.00 Mtr. 62.62 Mtr.

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable

1.1 KV grade to be erected as directed of following size.

(E) 3 core 2.5 Sq. mm

Total 700.00 Mtr. 137.36 Mtr.

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more

than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection.

(iv) above 90 to 120 watts

Total 164.00 Nos. 6566.01 Ea.

SBD SECTION-7 BILL OF QUANTITIES-319

Item No. & Description Qty. Unit Rate Per Amount

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe at road crossing or floor of

following size of cables.

(A) 4 core 10 Sq. mm

Total 700.00 Mtr. 676.70 Mtr.

(B) 4 core 16 Sq. mm

Total 700.00 Mtr. 987.78 Mtr.

providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark

Total 8.20 Nos. 270.68 Ea.

Pproviding and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at 415 V,having

normal current rating up to 25 A to 100A. with Fixed thermal &

magnetic release suitable to work on A.C. supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected in

existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Total 8.20 Nos. 6173.12 Ea.

Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board necessary

IP-42 and above protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body & doors,

SWG thick CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-charge with

supplied switch gears, BUSBARS, suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments, earth bus & earth

bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged

doors, handles with locking arrangement and rubber gasket,heavy

duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with

epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars, inter connecting

mains & Copper Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams) The panel shall be supplied

with following approved manufacturers with following size

(B) The standard companies switch gear shall be used and only

manufacturers at CPRI approved factory

(i) with 350mm depth

SBD SECTION-7 BILL OF QUANTITIES-320

Item No. & Description Qty. Unit Rate Per Amount

Total 8.20 Sq.Mtr 17584.10 Sq.Mtr

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner chemical

(CCM Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test report must be

[B] For Electrical installation up to 11 KV located in other than

normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr

Total 8.20 Nos. 8636.51 Ea.

Supplying and erecting approved make Conical Pole (Medium Duty )

Made from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

with required base plate and integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable terminations as erected on suitable

foundation (included) with necessary GI nut-bolts/J-Bolts. as per

details given by manufacturer considering site requirement.

The length of poles are as below.

(G) 9 Mtr. Long 70 mm Top X 205 mm bottom

dia, 3 mm thickness

Total 82.00 Nos. 16666.01 Ea.

Supplying and erecting street light pole bracket comprising main B

Class GI pipe of 4.2 cm/require outside dia. complete with suitable B

Class GI sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm or require size pole top having sufficient fastners for

fixing the brackets and having suitable rise as per site condition as

directed and spread of 2 mtr.with suitable welded stiffener reducer

and with lock nut complete painted with one coat of Red oxide / PU

base primer and two coats of Aluminium / PU paint. Suitable for side

entry fitting brackets of following nos of arms.paint with following nos

[B] Double Arm Bracket 2 Mtr.

Total 82.00 Nos. 1227.15 Ea.

SBD SECTION-7 BILL OF QUANTITIES-321

Item No. & Description Qty. Unit Rate Per Amount

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 60 x 60 x 150 cm. Deep in

below ground level with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm)

high upper ground level with necessary curing and finishing in

approved manner.

( for 9 & 10 mtr pole)

Total 82.00 Ea. 1652.36 Ea.

Supplying & erecting approved make Digital time switch having

lithium cell 6 years operative and operate battery backup 1 channel

day clock with 14 memory programme, suitable to operate on 240V +

5%, 16A with, floating contacts Minimum switching setup time

minimum & LCD display. Also comprised permanent ON/OFF

switching. Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as required with

necessary connection erected as directed.

Total 8.20 Nos. 3168.37 Nos.

Supplying & erecting power contactor ,AC3 duty for time switch

complete erected as per direction Cat III

[D] 4 pole 440V 40 Amp.

Total 8.20 Nos. 2782.55 Nos.

Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long

'B' grade G.I. pipe with necessary coupling buch buried in specially

prepared earth pit & G.I. earth wire of 8 SWG erected & connected as

Total 8.20 Nos. 823.15 Nos.

(D) LED Strip Light

(ii) Minimum 7.2W -240 LED per meter,(2 wire, IP-65) with non

integral suitable Driver complete Cat-lll

Total 1230.00 Rmt 220.18 Rmt

Total Amount Rs. ..............

Total Amount Rs. ..............

Add 18% GST Charge Rs…...…......

Add 3% Contigency Charge Rs…...…......

Net Amount Rs. ..............

SBD SECTION-7 BILL OF QUANTITIES-322

KHAMBHAT NAGARPALIKA KHAMBHAT

NAME OF WORK: LED SCREENS AT LAL DARWAJA ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE), AT

Sr. Qty. Unit Discription Total Unit Amount

1 2.00 Nos. supplying, installing, testing, and commissioning an advanced

outdoor LED display system with a 16:9 aspect ratio, made of

durable die-cast aluminium cabinets. The display will have a high-

resolution pixel pitch of up to 4 mm, a brightness of at least

nits, and IP65 protection for all-weather outdoor use. It is designed

for 24x7 continuous operation with wireless Wi-Fi connectivity for

remote content management. The scope includes providing the

mounting structure, power supply, cabling, earthing, surge

protection, and control system with software. Pixel Pitch: Maximum

4 mm * Display Size: Length 281–290 cm, Height 191–200 cm *

Brightness: Minimum 7000 nits (calibrated) * Life of Light Source:

100,000 hours * Ingress Protection: IP65 (front and rear) * Duty

Cycle: 24 x 7 continuous operation * Connectivity: Wireless Wi-Fi

802.11 b/g/n Finally, the system will be tested, commissioned, and

demonstrated, ensuring reliable performance as per the Engineer-in-

charge’s directions or any concern authority.

Add :- 18% of GST, Rs.

Add :- 1% of Qaulity Controll, Rs.

Add :- 2% of Contingency Charges, Rs.

SBD SECTION-7 BILL OF QUANTITIES-323

KHAMBHAT NAGARPALIKA KHAMBHAT

NAME OF WORK : ESTIMATE FOR ROAD FURNITURE AT LAL DARWAJA ROAD TO

PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE) , AT KHAMBHAT

SUB ESTIMATE :- FURNITURE

Qauntity Item Discription Total Rate Unit Amount

1 984.00 Road marking with hot applied thermoplastic paints with

Smt. reflectorising glass beads on bitumin surface providing

and laying a hot applied thermoplastic compound

mm thick including reflectorising glass beads @

250gms per sqm area, thickness of 2.5mm is excluding

of surface applied glass beds as per IRC:35- 2015. The

finished surface to be level, uniform and free from

streaks and holes. zebra patta /bump patta lane/center

line/ edge line/cut patta. The white color marking should

provide liminance coefficinet on cemend road shalll be

min 130 mcd/m2/lux and Asphalt road shall be min

mcd/m2/lux during the service life during the day time.

The marking should meet the performance criteria for

night time reflectivity, wet reflectivity and skid resistance

as mentioned in the section-15 of IRC 35-2015.

Warranty for the Retro reflectivity should be two years.

2 1220.00 Supplying and fixing Cat eye (Stimsonite) made out

Nos from Acrilo beautile sterine ijunction high compressed

molding with reflector made of MMC ( Prismetic type of

size 12cm x 6cm x 2.50cm) provided with betuminous

adhesive 100g. With each unit for fixing (High Intensity

SBD SECTION-7 BILL OF QUANTITIES-324

3 10.00 Direction (Junction) Sign :-Providing and fixing sign

Each boards made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite Panel); size 244x122 cms.

rectangular as per design of IRC-67- 2012. Pre treated

with phospheting process & acid etching; coated with

one coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 4.0mtr long (2

Nos.) stand post of 75 x 75 x 6mm / 65NB Circular MS

Pipe as required and frame fabricated from suitable

size iron angle of 50 x 50 x 5mm; painted with

bestquality epoxy coatings in black and white bends.

The details of symbol foreach board shall be as per

theinstruction of engineer in charge. The fixing at site

shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for

each leg.including excavation, curing etc.complete

under the supervision of engineer in charge. A warranty

for 10 years for the Retro reflective sheeting from

original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab for

the product offered shall be submitted by contractor.

(A) Class-C Type-11 Retro Reflective sheeting

4 10.00 Village Name Sign :-Providing and fixing sign boards

Each made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite Panel); size 90x60 cms.

rectangular as per design of IRC-67-2012. Pre treated

with phospheting process & acid etching; coated with

one coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 3.3mtr long

stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe

as required and frame fabricated from suitable size iron

angle of 35 x 35 x 3mm; painted with bestquality epoxy

coatings in black and white bends. The details of

symbol or inscription/letters / numerals for each board

shall be as per the instruction of engineer in charge.

The fixing at site shall be in 1:2:4 CC blockof size 45 x

45 x 60 Cms. for each leg.including excavation, curing

etc.complete under the supervision of engineer in

charge. A warranty for 10 years for the Retro reflective

sheeting from original manufacturer & a certified copy

of 3 year outdoor exposure test report from third party

test lab for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

SBD SECTION-7 BILL OF QUANTITIES-325

5 10.00 Facility Informatory Sign :-Providing and fixing sign

Each boards made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite Panel); size 80 x 60 cms

rectangular as per design of IRC-67-2012. Pre treated

with phospheting process & acid etching; coated with

one coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 3.6mtr long

stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe

as required and frame fabricated from suitable size iron

angle of 35 x 35 x 3mm; painted with bestquality epoxy

coatings in black and white bends. The details of

symbol foreach board shall be as per theinstruction of

engineer in charge. The fixing at site shall be in 1:2:4

CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under the

supervision of engineer in charge. A warranty for

years for the Retro reflective sheeting from original

manufacturer & a certified copy of 3 year outdoor

exposure test report from third party test lab for the

product offered shall be submitted by contractor. (A)

Class-C Type-11 Retro Reflective sheeting

6 2.00 STOP Sign :-Providing and fixing sign boards made out

Each of 2mm aluminium sheet / 4mm ACP (Aluminum

composite Panel); size 90 cms Octagone as per design

of IRC-67-2012. Pre treated with phospheting process

& acid etching; coated with one coat of epoxy primer

and two coats of best quality epoxy paint ;reflectorised

with Micro Prismatic Grade retro refiectivesheeting of

Type-11 as per ASTM D-4956 and latest

M.O.S.T.Specifications; 3.6mtr long stand post of 75 x

75 x 6mm / 65NB Circular MS Pipe as required and

frame fabricated from suitable size iron angle of 35 x

x 3mm; painted with bestquality epoxy coatings in black

and white bends. The details of symbol foreach board

shall be as per theinstruction of engineer in charge. The

fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x

60 Cms. for each leg.including excavation, curing

etc.complete under the supervision of engineer in

charge. A warranty for 10 years for the Retro reflective

sheeting from original manufacturer & a certified copy

of 3 year outdoor exposure test report from third party

test lab for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

SBD SECTION-7 BILL OF QUANTITIES-326

7 4.00 Route Marker sign :-Providing and fixing sign boards

Each made out of 2.0 mm aluminium sheet / 4 mm ACP

(Aluminum composite Panel); size 60x45 cm

rectangular plus 30x25cm additional plate as per

design of IRC-67-2012. Pre treated with phospheting

process & acid etching; coated with one coat of epoxy

primer and two coats of best quality epoxy paint

;reflectorised with Micro Prismatic Grade retro

refiectivesheeting of Type-11 as per ASTM D-4956 and

latest M.O.S.T.Specifications; 3.6 mtr long stand post

of 75 x 75 x 6mm / 65NB Circular MS Pipe as required

and frame fabricated from suitable size iron angle of

35x 35 x 3mm; painted with bestquality

epoxy coatings in black and white bends. the details of

symbol or inscription / numerals for each board shall be

as per the instruction of engineer in charge.The fixing

at site shall be in 1:2:4 CC block of size 45 x 45 x

Cms. for each leg.including excavation, curing

etc.complete under the supervision of engineer in

charge. A warranty for 10 years for the Retro reflective

sheeting from original manufacturer & a certified copy

of 3 year outdoor exposure test report from third party

test lab for the product offered shall be

submitted by contractor. (A) Class-C Type-11 Retro

Reflective sheeting

8 2.00 Providing and fixing overhead high intensity grade retro

Each reflective Informatory / Destination Boards 6 (six) Nos.

made out of 2mm aluminium sheet; size 180x120 cms

rectangle as per the design of IRC-67-1977. Pre-

treated with Phospheting process and acid-etching

coated with one coat of epoxy primer and two coats of

best quality epoxy paint, reflectorised with retro

reflective sheeting as per latest MOST specifications.

Letters and numerals should be as per IRC-30-1968.

The details of symbol of inscription/ numerals for each

board shall be as per the instruction of engineer in

charge. The boards shall be mounted on high level over

head type portal frame (Gantry) made out of MS

section of suitable size as per detailed drawing/ design

including cost of erection and painting.

9 10.00 Providing and fixing 5th Kilometer stone of precast C.C.

Each 1:2:4 including necessary reinforcement as per I.R.C.

type design in C.C. 1:4:8 including painting,lettering etc.

complete (For N.H., S.H. and M.D.R.)

SBD SECTION-7 BILL OF QUANTITIES-327

10 15.00 Providing and fixing Hectometer as per I.R.C. type

Nos. design including painting, lettering etc. complete.(ii)

Fixing in C.C. 1:5:10

11 16.00 The Solar Powerd Traffic Blinker are Manufactured by

Nos. using superior quality raw material & are known for their

uniterupted operation and self generated power. The

whole assembly includes solar panel, frame for solar

panel, traffic signal blinker, wire harness, charge

controller, battery, battery box, signal pole etc.

Add : 18% GST, Charges Rs. :

Add : 2% Contingency Charges Rs.

Add : 1% Quality Controll Rs.

SBD SECTION-7 BILL OF QUANTITIES-328

NAME OF WORK : PROVIDING ELECTRIFICATION INSTALLATION IN ENTRANCE GATE FROM LAL DARWAJA TO PANCHAVATI CIRCLE (

GAYATRI NAGAR CHOKE) AT KHAMBHAT.

Name of Document : Electrical Work Estimate for Entrance Gate At Khambhat.

SR REF. NO. DESCRIPTION QTY UNIT RATE AMOUNT

1 Provinding, Supplying , Fixing & installing Decorative Light with

required color LED with Designing & Drawing. Suitable For exterior

Installation for Entrance gate Including Colured LED, Outdoor LED

lights , MCB, ELCB, Required Wire/Cable With Switchgears, Control

panel, earthing and other necessary fittings and fixtures as designed 1.00 Job. 350000.00

by bidder and approved by authority/engineer in charge.[ Scop of

bidder :- Designing and submission for approval Information layout

Add : 18% GST, Charges Rs.

Add : 2% Contingency Charges Rs.

Add : 1% Quality Controll Rs.

SBD SECTION-7 BILL OF QUANTITIES-329

KHAMBHAT NAGARPALIKA, KHAMBHAT

ESTIMATE FOR SUPPLYING & ERECTING OF 12 METER HIGH MAST POLE WITH LED FIXTURES

AT ICONIC ROAD ATLAL DARWAJA ROAD TO PANCHAVATI CIRCLE (GAYATRI NAGAR CHOKE) AT

Quantity Unit Discription Total Rate Unit Amount

1 Supplying, erecting, testing, commissioning approved make M.S.

Polygonal High Mast Pole having following general Specification.

(a) Polygonal Section fabricated from M.S. Plate confirms BSEN

10025 & Hot deep galvanized minimum 65/86 micron (as per IS

2629 /1985) Lantern carriage with ring and rubber lines for

erection of luminaries of suitable site. (b) Maximum telescopic

section not more than four (c) Double drum gear pipe motorized

winch with 6mm dia S.S. Rod (For 16 mtr and above size) (d)

Approved make L.E.D. aviation light = 1 No. Lightening arrestor =

1 No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable

Unarmoured. (e) Bottom most section suitable for mounting

reversible motor and switchgears having door not more than

1400mm x 300mm with waterproof gasket & hinges & locking

arrangement. (f) Pole structure comprises suitable size of

reversible motor, cable and necessary switchgears with control

panel. (g) bottom section shall have suitable size of thickness

supports ribs foundation bolts nuts etc.

(h) Item not comprises the cost of lanterns.

(i) Necessary Cement Concrete foundation as per IS including

testing & commissioning of the entire structure for following size

of High Mast poles

3.00 Ea. [1] High Mast 12 Mtr. TOP A/F 105 mm, BOTTOM A/F 360mm,

No. of Sec. No. - 1, Bottom Thickness - 3 mm, Size of Base Plate -

Dia 520 mm x 20 mm thick, Foundation Bolt Size M24 x 850 mm,

Qty - 6 Nos., Suitable for mounting Fitting of Light - 6 Nos.

2 Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.)

SBD SECTION-7 BILL OF QUANTITIES-330

18.00 Nos. (B) Flood Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. (vii)

above 200 to 250 watts Cat-III

3 Providing and erecting XLPE (IS:7098)(I)-88 ISI marked

armoured cable multistrand Aluminium conductor for 1.1 KV. to

be laid on wall with necessary clamps or in existing cable trench

/ pipe at road crossing or floor of following size of cables.

60.00 Mtr. (A) 4 core 4 Sq. mm For Motor 117.16 Mtr.

60.00 Mtr. (A) 4 core 16 Sq. mm For Section Pillar Power 153.52 Mtr.

160.00 Mtr. (B) 4 core 25 Sq. mm For Section Pillar Power 190.89 Mtr.

4 Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including

value of earth resistance of installation duly stamped and signed

by agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report

must be submitted by Agency.

6.00 Nos. (b)For Electrical installation up to 11 KV in normal soil. Length of

Pipe : 2.00 mtrs Back filling Compound :1 no. Bag of 25 Kg.

5 160.00 Mtr. Providing & laying approved make Double Walled Corugated

pipe (DWC) of polythylene (Confirming to IS-14930-II) with

necessary connecting accessories of same materials at required

depth for laying of cable. Below ground / road surface for

enclosing cable and back filling the same to make ground as per

original. (B) 50 mm Dia 62.62 Mtr.

Add : 18 % GST, Rs.

Add : 2 % Contengancy Charges, Rs.

Add : 1 % Q. C. Charges, Rs.

SBD SECTION-7 BILL OF QUANTITIES-331

KHAMBHAT MUNICIPALITY, KHAMBHAT

NAME OF WORK :- PROPOSED CIRCLE DEVELOPMENT OF LALDARVAJA CIRCLE FOR ICONIC ROAD ,AT

Item Qty. Description Total Unit Amount

1 1.00 Demolition of Existing Existing Circle including foundation, ground

Job beam, steel structure, roofing, truss, wall etc. completed. With

disposal of unserviciable materials and stacking of serviciable

material with all lead and lift. Completed as directed by engineer in

charge or any concern authority.

2 9.00 Excavation for foundation upto depth 1.5 m. including sorting out and

Cmt. stacking of useful material and disposing off the excavated stuff upto

50 m lead (A) loose or soft soil

3 6.00 Filling available excavated earth (excluding Rock) in trenches. Plinth,

Cmt. sides of foundations etc. in layers not exceeding 20cm. In depth

consolidating each disposited layer by ramming and watering.

4 24.50 Filling in foundation and plinth with murrum or selected soil in layers

Cmt. of 20cm thickness including watering, ramming and consolidating

5 3.50 Providing and laying cement concrete 1:3:6 (1 Cement, 3 coarse

Cmt. sand, 6 Black Trap stone aggregates 40mm nominal size) and

curing complete excluding cost of formwork in (A) Foundation.

6 18.50 Providing and laying controlled cement concrete M.250 and curing

Cmt. complete excluding the cost of formwork and reinforcement for

reinforced concrete work in (B) Walls, from top of foundation level

upto floor two level 5739.83 Cmt.

7 1975.00 T.M.T. Bars

Kgs. Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level

SBD SECTION-7 BILL OF QUANTITIES-332

8 92.00 20 mm thick sand faced cement plaster on walls up to heinht

Smt metres above ground laval cosisting of 12 mm thick backing coat of

C:M 1:3 (1-cement :3-sand) and 8mm thick finishing coat of C:M 1:1

(1-cement :1-sand) etc complete.

9 34.50 Providing and laying polished Granite tiles 18 mm thick in Flooring,

Smt. risers of steps, skirting Dedo and pillars laid on 10 mm thick cement

mortar 1 : 3 (1 cement : 3 course sand) and jointed with gray cement

slurry mixed with pigment to match the shade of slab including

rubbing, polishing, Moulding etc. complete. For Flooring, Doors &

10 17.50 Providing and laying polished kota stone slab 25mm thick in risers of

Smt. steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3

(1-Cement : 3 coarse sand) and jointed with gray cement slury mixed

with pigment to match the shade of slab including rubbing and

polishing etc. complete.

11 200.00 Providing and fixing stainless steel (Grade 304) railing made of

Kgs. Hollow tubes, channels, plates etc. including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories & stainless

steel dash fasteners, stainless steel bolts etc. of required size, on the

top of the floor or the side of waist slab with suitable arrangement as

per approval of Engineer in-charge.

12 50.50 Development of lawn including excavation of area up to 150 to

Smt. mm depth as per requirement and disposal of same outside

premises, removing of weeds, cleaning, spreading garden soil,

organic fertilizer and mixing same, applying anti termite insecticides,

supplying and laying of carpet lawn, watering. And maintain up to two

month.(supplying of required quantity of carpet lawn shall be in the

scope of contractor).(With Two Years of Maintenance including

Replacement of Damage Plant, lawn Etc With Required

insecticides, pesticides, Fertilizer etc Complete as Directed By

13 1.00 Providing and fixing Statue/Sclupture with all necesarry fittings,

No materials, plumbing and electrical installation with colorful Lightning

features etc. as per directed by Engineer in charge.

14 50.00 Provinding & Supplying Synergy plast plastic flower pot of any color

Nos. ,Rectangular or oval shaped as per qoutation detailed etc. complete

SBD SECTION-7 BILL OF QUANTITIES-333

15 50.00 Providing and Displaying Acalypha Different colour well developed,

Nos. fresh &healthy with good foliage, multi branch 30 to 45 cm ht. in

cm size ofEarthen Pot/ Plastic Pot bushy as per direction of the

officer-in-charge.

16 6.00 0.90MT HIGH SCULPTURE / MONUMENT

17 6.00 ARTIFICIAL TREE WITH LED ROPE LIGHT WRAPPING IN

Nos. HELICAL SHAPE 4545.00 No.

18 8.00 Providing Supplying And Erecting Architectural pole of 5 mtr. Height

Each double arm made of galvanised icon sections of 140mm dia. &

76mm dia Inc.70W hanging type decorative luminaire made of aput

aluminum body with pressure din-cast hent management (PDCHM)

and the IP65 optical compartment with high power LEDs with Inc.

wireing ,Foundatation & Rope light 6 mtr. As per direction of the

Engineer-in-charge.

Total Amount, Rs.

Total Amount, Rs.

Add :- 18% of GST, Rs.

Add :- 1% of Quality Controll, Rs.

Add :- 2% of Contingency Charges, Rs.

SBD SECTION-7 BILL OF QUANTITIES-334