Construction of Additional accommodation for Govt. Sr. Sec. School at Daroh in Tehsil Palampur, Distt. Kangra (H.P.)

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil for any length clear from the edge of excavation and then returning the stacked soil in15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-Incharge, within all leads, lifts of materials and other incidentals.

Excavation in drains and channels etc; in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturator soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimeter) layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- In-charge, within all leads, lifts of materials and other incidentals.

Filling in plinth with sand under floors including watering ramming and consolidating and dressing complete to the entire satisfaction of the Engineer-in-charge within all leads and lifts of materials and other incidentals.

Providing form work with steel plates 3.15mm. (Three decimal fifteen milimetre) thick welded with angle iron frame 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ).,so as to give a fair finish including centering shuttering, strutting and propping etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation, footings, bases of columns etc and mass concrete including carriage of materials within all leads and lifts and other incidentals

Providing form work with steel plates 3.15mm.(Three decimal fifteen milimetre) thick welded with angle iron in frame 30x30x5mm.,(Thirty into thirty into five milimetre)so as to give a fair finish including centring,shuttering strutting and proping etc. with wooden battens and ballies complete upto any heights/ depth of propping and centering below supporting floor to ceiling and removal of the same for insitu- reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like including carriage of material within all leads, lifts and other incidents.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters)thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams hunching, cantilevers bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters)thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plan, within all leads, lifts of materials and other incidentals.

Providing form work with steel plates 3.15mm. (Three decimal fifteen milimetre) thick welded with angle iron frame 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ).,so as to give a fair finish including centering shuttering, strutting and propping etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling upto all heights and removal of the same for in-situ reinforced concrete and plain concrete work in stair cases with slopping or stepped soffits excluding landing including carriage of materials within all leads and lifts and other incidentals

Providing form work with steel plates 3.15mm. (Three decimal fifteen milimetre) thick welded with angle iron frame 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ).,so as to give a fair finish including centering shuttering, strutting and propping etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under 20cm (Twenty centimetre. wide the rate is inclusive of all leads and lifts of materials and other incidentals.

Providing form work with steel plates 3.15mm.(Three decimal fifteen milimetre) thick welded with angle iron in frame 30x30x5mm., (Thirty into thirty into five milimetre)so as to give a fair finish including centring,shuttering struting and proping etc. with wooden battens and ballies including dewatering/ pumping or bailing out water wherever required at site complete upto any heights/ depth of propping and centering below supporting floor to ceiling and removal of the same for insitu- reinforced concrete and plain concrete work in vertical surfaces such as walls of any thickness,partition and the like including attached pillasters buttresses,plinth and string courses and the like including carriage of material within all leads, lifts and other incidents.

Providing and laying cement concrete 1:4:8 ( One Cement : four Sand: eight graded Stone aggregate 40mm (Forty milimetre ) nominal size and curing complete in foundation and plinth excluding the cost of form work. /under flooring including carriage of materials within all leads, lifts and other incidentals

Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded /broken stone crushed aggregate 40 mm (forty milimetre nominal size) mechanically mixed, curing complete excluding the cost of form work in foundation and plinth including carriage of materials within all leads and lifts and other incidentals

Providing and laying cement concrete 1:6:12 (one cement:six sand:tweleve graded crushed stone agg. 40 mm (forty milimetre) nominal size mechanically mixed and vibrated and curing complete excluding the cost of centring and shuttering in foundation and plinth including carriage of materials and other incidentals with in all leads, lifts and other incidentals

Providing and laying cement concrete grade M-20 design mix with minimum cement contents 330 Kg. (Three hundred thirty kilogramme per Cubicmetre) 20mm (Twenty milimetre) Crushed stone aggregate mechanically mixed and vibrated and curing complete excluding the cost of form work and reinforcement for R.C.C. work in Foundations, footings bases of columns and the like and mass concrete including carriage of materials within all leads and lifts and other incidentals

Providing and laying cement concrete works of grade M-20 (M-Twenty) design mix to obtain the minimum crushing strength of 20N/mm2 with minimum cement contents 310 Kg. (Three hundred ten kilogramme per Cubicmetre) mechanically mixed and vibrated including curing complete excluding the cost of form work and reinforcement for reinforced cement in suspended floor roof landing shelves their support balconies beam girders bressumer and cantiliver including moulding cornices etc. upto all floor level including carriage of materials within all leads and lifts and other incidentals

Providing and laying cement concrete works of grade M-20 (M-Twenty) design mix to obtain the minimum crushing strength of 20N/mm2 with minimum cement contents 310 Kg. (Three hundred ten kilogramme per Cubicmetre) mechanically mixed and vibrated including curing complete excluding the cost of form work and reinforcement for reinforced cement in suspended floor roof landing shelves their support balconies beam girders bressumer and cantiliver including moulding cornices etc. upto all floor level including carriage of materials within all leads and lifts and other incidentals

Providing and laying cement concrete grade M-20 (M-Twenty) design mix to obtain the minimum crushing strength of 20N/mm2 with minimum cement contents 310 Kg. (Three hundred ten kilogramme per Cubicmetre) 20mm (Twenty milimetre) Crushed stone aggregate mechanically mixed and vibrated and curing complete excluding the cost of form work and reinforcement for R.C.C. work in Columns, pillars posts and struts upto all floor level including carriage of materials within all leads and lifts and other incidentals.

Providing and laying cement concrete grade M-20 (M-Twenty) design mix with to obtain the minimum crushing strength of 20N/mm2 minimum cement contents 310 Kg. (Three hundred ten kilogramme per Cubicmetre) 20mm (Twenty milimetre) Crushed stone aggregate mechanically mixed and vibrated and curing complete excluding the cost of form work and reinforcement for R.C.C. work in stair cases except spiral stain cases excluding landing but including preparing of the surface and finishing of nosing upto all floor level including carriage of materials within all leads and lifts and other incidentals

Providing and laying cement concrete grade M-20 (M-Twenty) design mix to obtain the minimum crushing strength of 20N/mm2 with minimum cement contents 310 Kg. (Three hundred ten kilogramme per Cubicmetre) 20mm (Twenty milimetre) Crushed stone aggregate mechanically mixed and vibrated and curing complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in string courses coping bed plates, anchor blocks plain windows sills and the like including carriage of materials within all leads and lifts and other incidentals

Providing and laying reinforcement cement concrete works of grade M-20 (M-Twenty) design mix to obtain the minimum crushing strength of 20N/mm2 with minimum cement contents 310 Kg. (Three hundred ten kilogramme per Cubicmetre) mechanically mixed and vibrated including curing completed but excluding the cost of form work and reinforcement for reinforced cement in walls any thickness not less than 0.10 m thickness including attached pilaster, butteresses plinth and string courses etc. upto all floor level including carriage of materials within all leads and lifts and other incidentals

Providing Tor steel reinforcement for Reinforced cement concrete work including bending, binding and placing in position and including cost of binding wire complete for all floors including carriage of materials within all leads and lifts and other incidentals.

Second class brick masonry in common burnt clay building bricks in super structure above plinth level upto floor any level in cement mortar 1:6 (One Cement is to Six Sand). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Second class half brick masonry in common burnt clay building bricks in super- structure above plinth level upto floor any level in cement mortar 1:4 (One Cement is to Four sand ). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Second class half brick masonry in common burnt clay building bricks in super- structure above plinth level upto floor any level in cement mortar 1:4 (One Cement is to Four sand ). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Stone filling / bat aggregate in soak pit including carriage of material within all leads,lifts and other incidentals.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints with cement mortar 1:6 (One cement Six sand) including carriage of materials within all leads and lifts of materials and other incidentals .

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints with cement mortar 1:5 (One cement five sand) including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing factory made flush door shutter 35mm thick (thirty five millimetre thick, commercial both side i.e. non decorative, (Phenol bounded, termite resistant and water proof) core of block board construction with full frame of first class hard wood well matched commercial three ply veneer with vertical grain or cross bend & face veneer on both sides of flush door ISI marked No. IS 2202 of kit ply or equivelent completed including carriage of materials within all leads, lifts, and other incidentals.

Providing and fixing 19mm (Nineteen milimetre) thick commercial board cup board shutter all cut portion of shutter shall be finished with 6mm (Six milimetre) thick hard wood edging including nikel plates bright finished piano hinges including carriage of materials within all leads and lifts and other incidentals

Providing and fixing 19mm (Nineteen milimetre) thick water proof termie registance commercial board in shelves/ box for cup board butt joints and fixing with nails and screws etc. complete. All cut portion of the shelves shall be finished with 6mm (Six milimetre) thick hard wood edging. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 6mm (Six milimetre) thick ply wood linning with butt jointing and nails (Frame work and cover fillets to be measured and paid for separately). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 19mm ( Nineteen milimetre) thick water proof commercial board shutter with hard edging and 0.63mm (Zero decimal sixty three milimetre) thick PGI (plain galvanised iron) sheet lining in the inside of shutter of approved size including bright finished nical plated pino hinges etc, complete as per detailed architectural drawings including carriage of materials within all leads, lifts and other incidentals.

providing and fixing Ist class deodar wood 12mm (Twelve milimetere) thick and 100mm (Hundred milimetere)wide pelmet with 25mm(Twenty five milimetere) diametere wooden curtain rod and brackets including fixing witgh 25x3mm(Twenty five into three milimetere) M.S flat 10cm. Long and plugs etc. complete including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 12mm ( Twelve milimetre) thick prelaminated Phenol boundedsuede finish black board size 1.80x1.00 mtrs) (One point eight zero into one point zero metre) board bounded exterior/ interior grade both side Including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing Megnetic Catcher for cup boards shutter with necessary screws complete including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 65x35mm (Sixty five into thirty five milimetre) special quality C.P. brass cup board lock with six leavers including necessary screws completed including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred milimetres) bright finished brass door stoper with rubber cushion screws etc to suit shutter thickness cmoplete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer- in-charge.

Providing and fixing M.S. plain grills of required pattern in frames of windows etc. with M.S. round headed bolts and nuts or by screws including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85-G with a wire of dia 0.56(Zero decimal Fifty six milimetres) for doors and windows and clerestory windows including bright finished black enameled iron hinges with necessary screws 40mm thick (Forty milimetres) 2nd class deodar wood, within all leads and lifts and other incidentals.

Providing and fixing 300X16mm (Three hundred fifty into Sixteen milimetre) size oxidized M.S. sliding door bolt bright finished or black enamelled with nuts and screws etc. complete including carriage of materials within all leads, lifts, and other incidentals.

Providing and fixing anodized M.S. tower bolts (barrel type) anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including carriage of materials within all leads, lifts, and other incidentals.

200x10mm (Two hundred into ten milimetre) size

150x10mm (One hundred fifty into ten milimetre)size

Providing and fixing oxidized M.S. handles or shade with necessary screws etc. complete including carriage of materials within all leads and lifts and other incidentals

(a) 125 mm (One hundred twenty five milimetre)

b) 100mm (One hundred milimetre)

c) 75mm (Seventy five milimetre)

Providing and fixing oxidized 250mm (Two hundred fifty milimetre) size hooks and eyes complete in all respect. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Precast automatic hydraulically compressed terrazzo tiles 25mm (Twenty five milimetre) thick with marble chips of 30cmx30cm (Thirty centimetre into thirty centimetre ) size laid in floor treads of steps and landings on a bed of 25mm average thickness of cement mortar 1:6 (one cement : six sand) jointed with pigment to match the shade of tiles (Wherever required) including rubbing and polishing complete with tiles of silver grey shade ISI marked I.S 1237 of approved shade and ratio including carriage of materials within all leads and lifts and other incidentals

Precast automatic hydraulically compressed terrazzo tiles 25mm (Twenty five milimetre) thick with marble chips of 30cmx30cm (Thirty centimetre into thirty centimetre ) size laid in skirting and risers of steps on 10mm average thickness of cement mortar 1:3 (one cement : three sand) jointed with pigment to match the shade of tiles (Wherever required) including rubbing and polishing complete with tiles of silver grey shade ISI marked I.S 1237 of approved shade and ratio including carriage of materials within all leads and lifts and other incidentals

40 (forty) millimetre thick cement concrete flooring 1:2:4 (one cement: two sand: three graded crushed stone aggregate 20 mm (twenty milimiter ) nominal size laid in one layer finished with a floating coat of neat cement including carriage of materials within all leads, lifts, and other incidentals.

white glazed tiles 6 mm (Six milimetre) thick 30x20cm (Thirty into twenty centimetre) in skirting risers of steps and dado 12 mm (Twelve milimetre) thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of materials within all leads, lifts and other incidentals

15 (Fifty) millimetre thick cement plaster skirting thick (up to any height (with cement mortar 1:3 (One cement : three sand) finished with a floating coat of neat cement including rounding of junction with floor within all leads, lifts and other incidentals.

Precast automatic hydraulically compressed tiles 22mm ( Twenty two milimetre) thick with cement concrete chequred tiles of 30cmx30cm (Thirty centimetre into thirty centimetre ) size laid in floor treads of steps, ramp and landings on a bed of 25mm ( twenty five milimetre) average thickness of cement mortar 1:6 (one cement : six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (Wherever required) including rubbing and polishing complete with tiles of grey shade ISI marked I.S 1237 of approved shade and ratio including carriage of materials within all leads and lifts and other incidentals

Providing and laying matt finish ceremic tiles 5.5mm.(Five decimal five milimetre) thick in flooring and treads of steps 300x300mm. (three hundred into three hundred milimetre)size laid on a bed of 12mm (Twelve milimetre) thick cement mortar 1:3 ( One Cement : Three Sand ) finished with flush pointing in white cement within all leads and lifts of materials and other incidentals.

Precast automatic hydraulically compressed terrazzo tiles 22mm (Twenty two milimetres) thick with marble chips chequred tiles of 30cmx30cm (Thirty centimetre into thirty centimetre ) size laid in floor treads of steps, and landings on a bed of 25mm (Twenty five meilimetre) average thickness of cement mortar 1:6 (one cement : six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (Wherever required) including rubbing and polishing complete with tiles of silver grey shade ISI marked I.S 1237 including carriage of materials within all leads and lifts and other incidentals

Providing and fixing (40 mm ( Forty milimetre) wide and 6mm (Sixty milimetre) thick) glass strips in joints of terrazo floors including carriage of materials within all leads, lifts and other incidentals

Providing and laying marble work (Table rubbed and polished ) in flooring 20 mm(Twenty milimetre) thick base in cement mortar 1:3 (one cement:three sand ) including jointing with cement mortar 1:2(one white cement: Two Marble dust) with an mixture of pigment to match the shade of the marble 20 mm (Twenty milimetre) thick white makrana marble in all floors within all leads and lifts of materials and other incidentals.

Providng and Fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with preparinted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limp-et and rubber washers complete with all accesories as required as per the Direction of Engineer-in-Charge including carriage of materials within all leads, lifts of materials and other incidentals .

Providing and fixing PGI Sheet 0.63mm thick in expansion joint with overall width 45 cm fixed to beam /slab with wooden plugs and screws i/c bending to slope and fixed in bitumen mix filler in proporation of 80 kg bitumen 1 kg of cement & 0.25 cum of sand hot mixed complete including carriage of materials within all leads, lifts, and other incidentals. The rate including of toll tax, sale tax or other taxes imposed by the government.

Providing and fixing Screen shall be made of 19x19mm (Nineteen into nineteen milimetre) hollow square pipe welded to M.S hollow section of size 50x50mm (Fifty into fifty milimetre) supported on bracket made of 25x3mm (Twenty five into three milimetre) M.S flat frame covered with M.S sheet as per detail drawing etc., including carriage of materials within all leads, lifts, and other incidentals. The rate including of toll tax, sale tax or other taxes imposed by the government.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per directions of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals.

Providing and fixing 15cm. (Fifteen centimetre) wide 45cm.(Forty five centimetre) Overall semicircular plain G.I. Sheet 0.63mm (Zero decimal six three)milimetre thick gutter with iron brackets 40x3mm (Forty into three milimetre)size, bolts nuts and washers etc. including making necessary conections with rain water pipe complete as per design including carriage of materials with in all leads , lifts and other incidentals

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidents.

Providng and Fixing M.S. B.P Sheet 2mm (Two milimetre) thick in eaves board/facia/soffits/ceiling including cuttng, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge (base members of steel work shall be measured & paid separately) including carriage of materials within all leads, lifts of materials and other incidentals .

Providing and fixing 100mm (One hundred milimetre) diameters pipe on wall face PVC (D-Plast) Rain water pipes of working pressure not less than 4.5 kg/square centimeter including filling the joints with approved adhesive complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face P.V.C. (D-plast)acessories for rain water pipes including filling the joints with approved adhesive complete and within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer- in-charge.

100mm (One hundred milimtres)diametere PVC Plain bend

100mm (One hundred milimtres)diametere PVC shoe

Providing and fixing 100mm (One hundred milimetre) dia metre M. S. holder bat clamps of approved design to PVC pipes embedded in and including cement concrete block 10cmx10cmx10cm (Ten centimeter into Ten centimeter into Ten centimeter) of 1:2:4 (One cement is to Two Sand is to Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size and cost of cutting holes and making good the wall etc. Including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections trusses and frame work including cutting hoisting and fixing in position and applying a primer coat of red lead paint In trusses and trussed purlins in buildings including carriage of materials within all leads lifts and other incidentals.

Providing and fixing angle iron door , windows, clerestory window frame manufactured from M.S. angle iron section of 40x40x6mm(forty into forty into six milimetre) including hinges jamb, lock jamb, beed and if required angle threshold of mild steel angle 50x25 mm (Fifty into twenty five milimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5 mm (Two decimal five milimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals.

Providing and fixing angle iron door frames (double rebate) manufactured with frame for steel section of 35x35x4mm (Thirty five into thirty five into four milimetre) and M.S. flat 50x4mm (Fifty into four milimetre) in combination as per Drawing and design including hinges jambs, locks, mild steel M.S. angle 50x25mm (Fifty into twenty five milimetre) welded or rigidly fixed by mechanical means lugs with split and tails to each jamb including steel butt hinges 2.5mm (Two point five milimetre) thick with provision of locking arrangement and shock observers as specified and applying a coat of special steel primer including carriage of materials within all leads lifts and other incidentals.

Providing and fixing angle iron cup-board (frame manufactured from M.S angle iron sections 25x25x4mm (Twenty five into twenty five into four milimetre) welded or rigidly fixed by mechanically means luge split and tails to each jambs including steel butt hinges 2.5 mm (Two point five milimetre) thick with provision for looking arrangements and shock absorbers as specified and applying a cost of approved steel primer after pre-treat-ment of the surfaces or as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals .

Providing and fixing M.S. channels in doors and windows frames manufactured from M.S. channels section 75x40mm (Seventy five into forty milimetre) 4mm (Four milimetre) thick with combination for mellions M.S. flat 75x4mm (Seventy five into Four milimetre) as per design drawing welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel butts hinges 2.5mm (Two decimal five milimetre) thick with a provision of locking arrangements shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-Charge. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded and including iron fitting, including providing and fixing of glass pans with glazing clips and special metal sash putty of approved make complete including applying a coat of read lead paints within all leads, lifts of materials and other incidentals.

Fixed steel windows

Top hung ventilators

Providing and fixing factory made double shutter for steel windows side hung (one glazed and other wire gauged) of standard rolled steel section joints with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with glazed clips and special metal such putty of glazed side of shutter and wire gauge of IS designation 85G with metal beading fixed with bolts and nuts on other side complete including priming coat of red lead paint within all leads, lifts of materials and other incidentals.

Providing and fixing M.S. rectangular pipe stair railing over M.S. flat having baluster 20mmx20mm and 12mmx12mm ( Twenty milimetre into twenty milimetre and twelve milimetre into twelve milimetre) M.S. solid square bars in combination with M.S. flat 40x6mm (Forty into six milimetre) with a clear height of 85cm @ 60 C/C, jointing in cement concrete steps and jointing with electrical gas welding at top along wing hand rail of hollow M.S rectangular pipe of 75x25mm (Seventy five into twenty five milimetre) (SWG-16) Vertical M.S solid squiare bars, baluster welded/ jointed with each with 2 Nos. M.S flat of 40x6mm (Forty into six milimetre) complete with a priming coat of read paint as per specification and direction of the Engineer-in-Charge. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 50mm diameter M.S. pipe hand rail slip resistant with round ended joint at two levels at 75 and 90cm height welded with 25mm diametre baluster embeded in cement concrete 60 C/C, jointing in with electrical gas welding at top along wing hand rail of hollow M.S pipe of 50mm diametre ( SWG-16). The baluster welded/ jointed with each with 2 Nos. M.S flat of 50x5mm complete with applying priming coat of read paint as per specification and direction of the Engineer-in-Charge. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease dirt and other foreign matter sand paparing and knotting ready mixed paint brushing wood primer pink including carriage of materials within all leads and lifts and other incidentals

Painting two coats (excluding priming costs) on new wood and wood based surfaces with enamel paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping within all leads, lifts of materials and other incidentals.

Painting two coats (excluding priming coats) on new steel and other metal surfaces with enamel paint brushing to give and even shade including cleaning the surfaces of all dirt dust and other foreign matter enamel paint other than white including carriage of materials within all leads and lifts and other incidentals

6mm (Six milimetre) thick cement plaster to ceiling with cement mortar 1:3 (One cement: Three sand) including carriage of materials within all leads, lifts and other incidentals

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:6 (1 cement : 6 sand) within all leads, lifts, and other incidentals

15 mm (Fifteen milimetre) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:6 (1 cement : 6 sand) within all leads, lifts, and other incidentals

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:5 (One cement : Five sand) including carriage of material within all leads, lifts and other incidentals.

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:3 (One cement : three sand) including carriage of material within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish so as to the surface complete including carriage of materials within all leads and lifts of materials and other incidentals .

Distempering with dry distemper of approved brand and manufacture (two coat) and of required shade on undecorated wall surfaces to give an even shade over and including priming coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth including carriage of materials within all leads, lifts, and other incidentals.

Wall painting (Two coats) with synthetic enamel paint of approved brand and manufacture for interior grade on undecorated concrete/ stone/ plastered wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for making the surface within all leads and lifts of material and other incidental

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings & other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer. including carriage of materials within all leads, lifts, and other incidentals

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete including carriage of materials within all leads, lifts, and other incidentals.

Finishing wall with apexweather proof exterior grade emulsion of Asian Paintes or its equivalent of approved shade or its equarlied on undecorated wall surfaces ( Two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including carriage of material within all leads, lifts and other incidents.

Providing under layer for plinth protection of 75 mm (Seventy five milimetre) thick unconsolidated) bed of dry brick stone broken aggregate 40mm (Forty Milimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground within all leads, lifts of material and other incidentals.

Providing plinth protection 50mm(Fifty milimetre0 thick with cement concrete 1:3:6 (One cement :Three sand: Six graded stone aggregate 20mm (Twenty milimetre)nominal size including finishing the top surface of concrete smooth within all leadsand lifts of material and other incidentals

Construction of cement concrete covered drain in cement concrete 1:3:6 ( One Cement : Three Sand : Six graded stone aggregate) earth work, shuttering and cast-in- situ R.C.C. slab over drain and C.C flooring 1:2:4 ( One Cement : Two Sand : Four graded stone aggregate) and finishing with a floating coat of neat cement complete as per standard drawing including carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete 1:5:10 (One cement isto Five Sand isto Ten graded crushed stone aggregate 40mm (Forty milimetre) nominal size) in haunching of stone ware pipe of 150mm (One hundred fifty milimetre) internal diametres including concrete for bedding necessary form work and curing complete within all leads, lifts and other incidentals.

Providing and fixing Plytheline - Aluminium - Plyethylene (PE-AL0PE) composite pressure pipe U.V stabilized with carbon black confirming to IS - 15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) Pipes exposed on wall including carriage of materials with in all leads, lifts and other incidental .

1216 (16 mm O.D. pipe).

P/L in trenches galvanized mild steel tubes (medium grade tube) fittings (earth work in trenches to be measured and paid for separately) 20mm (Twenty milimetre) nominal bore. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Making connection of galvanised steel distribution branch with galvanised mild steel 20mm to 40mm (Twenty milimetre to forty milimetre) nominal bore by providing & fixing tee including cutting and threading the pipes complete including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 110mm ( One hundred ten milimetre) dia high pressure P.V.C spigot and socket soil, waste and ventilating pipe I.S.I Marked including fixing with approvfed adhesive etc. complete The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

150mm (One hundred fifty milimetre) dia

100mm (One hundred milimetre) dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

150mm (One hundred fifty milimetre) dia

100mm (One hundred milimetre) dia

Providing and fixing PVC collars ISI markedincluding fixing with approved adhesive etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

150mm (One hundred fifty milimetre) dia

100mm (One hundred milimetre) dia

Providing and fixing PVC double equal branch with oval access door, insertion rubber asher 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

150mm (One hundred fifty milimetre) dia

110mm (One hundred ten milimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

100mm (One hundred milimetre) dia

150mm (One hundred fifty milimetre) dia

Providing and Fixing 100mm x90mm( one hundred milimetre into ninety milimetre) nominal sizse P.V.C. floor trape completed in all respect as per directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet (Anglo indian sheet white shade W.C. pan) pluto category No. 20065 of hindware cera/ or its equavalent as per direction of Enginner in charge, in white shade with dual cistern with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(One cement : One sand) (Seat and over to be measured and paid for separately):- Ordinary closet. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet squatting pan orrissa pattern W.C pan) size 580mmx 440 x 300mm (Five hundred eighty into four hundred forty into three hundred milimetre) in white shade with dual flus cistern category No. 21029 in white shade of hind ware / cera or its equivalent as per direction of Enginner in charge, (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa Pattern The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete. 110 mm dia The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, osquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately). 10 litres net capacity. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing G.I. Inlet connection for flush pipe with W.C. Pan The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing plastic seat (Solid type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers SOLID TYPE: a white plastic seat and cover. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 59x32.5x39cmISI 2556 Hindware flat back vitreous China bowl pattern urinal Code OC-13 in white shade of orient ceremic or its equivalent as per direction of Enginner in charge, including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing Stainless steel kitchen sink of size 610x460mmx 200mm ( Six hundred ten into four hundred sixty into two hundred milimetre) with drain board including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 600mm x 450 mm (Six hundred milimetre into four hundred fifty milimetre) bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing C.P. Brass Towel rail of Jel/ EES- ESS complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 750mm x 20mm (Seven hundred fifty into Twenty milimetre) ISI mark No. 8931. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing charomium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. Brass screws . The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing C.P. stop cocks of Jel/ ESS- ESS 15mm (Fifteen milimetre) dia . The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

P/F C.P Brass bib tap of Jel/ ESS- ESS with capstan head 15mm (Fifteen milimetre) dia. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

C.P Brass pillar tap of Jel/ ESS- ESS with Capstan head 15mm (Fifteen milimetre) dia .The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.I. Union for wash basin or sink 32mm (Thirty two milimetre) dia . The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing C.P. brass full way valve of Jel/ ESS- ESS with wheel 15mm (Fifteen milimetre) nominal bore. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 25 x 40x 83 cm (Twenty five into forty into eighty three centimetre) in white shade of hind ware / cera or its equivalent No. 2556 as per direction of Enginner in charge, vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings:- Flat back .The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :-1000 Litres net capacity of each tank. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 600mm x 120 mm (Six hundrred into one hundred twenty milimetre) glass shelf with C.P. Brass of Jel/ EES- ESS bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing chromium plated brass soap dish with C.P. Brass of Jel/ ESS- ESS brackets fixed to wooden cleats with C.P. Brass screws. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Constructing manhole with RCC top slab in 1:2:4 mix in (One Cement: Two Sand: Four graded stone aggregate 20mm (Twenty milimetre) nominal size), foundation concrete 1:4:8 (One Cement: Four Sand: eight graded stone aggregate 40mm nominal size), inside plastering 15mm (Fifteen milimetre) thick with cement mortar 1:3 (One Cement: Three Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ((One Cement: Two Sand: Four graded stone aggregate 20mm (Twenty milimetre) nominal size) finished smooth complete including curing and testing Inside size 800mmx800mm and 500mm deep including C.I. cover with frame, (Light duty single seal pattern –I) 455mmx610mm internal dimensions total weight of cover and frame to be not less than 38 kg(weight of cover 23kg and weight of frame 15kg) with 300mm thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 ( One Cement: Three Sand). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends with common burnt clay buiolding bricks in cement mortar 1:5 ( One Cement : Five Sand ) C.I. cover with frame (Light duty) 355 mmx 610mm internal dia mensions total weight of cover with frame to be not less than 38 Kg. ( Eight of a cover 23 Kg. and wight of frame 15 Kg.) R.C.C. top slab with 1:2:4 mix ( One Cement :o Sand : graded stone aggregate 20mm nominal size foundatin concrete 1:5:10 ( One Cement Five Sand :aded Stone aggregate 40mm nominal size) iside plaster 15mm thick with cement mortar 1:3(One Cement : Three Sand ) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete: Inside dimensions 455mm x610 mmx450mm deep single pipe line including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing C.P. jet spray of approved quality of Jel/ ESS- ESS and colour with 1.5 mtr. (one decimal five metre) tube. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing ferrule including boring and taping the main 20mm (Twenty milimetre) nominal bore. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 15mm ( Fifteen milimetre) G.I./M.I Union of following sizes (where not included in the items . The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 20mm ( Twenty milimetre) G.I./M.I Union of following sizes (where not included in the items . The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with ointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials with in all leads, lifts and other incidental .

Equal Tees 1216

Femalebranch TEE 1216 X 1216 X 15 mm thread

Female elbows:- 1216 X 15 mm thread.

Male thread connector:- 1216 X 15 mm thread.

Providing and laying 150mm (One hundred fifty milimetre) cement concrete 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of the following internal diameters, necessary form work and curing complete.The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 455 x610 mm light duty rectangular C.I Manhole with frame cover weight to be not less than 38 kg . (Thirty eight Kilogram) The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 100mm ( One hundred milimetre) P.V.C.Cowal The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing, laying (to level or slopes) P.V.C. Pipe 150mm ( One hundred fifty milimetre) dia including tasting of pipes and joints complete: The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 20mm (Twenty milimetre) nominal diametre to wall ceiling and floor galvanised mild steel tube ( medium grade ) to be fixed with clamps including making good the walls, ceiling and floor including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 150mm ( One hundred fifteen milimetre) PVC plain bend ISI marked including fixing with approved adhesive etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

M/S BALDEV KUMAR GOVT. CONTRACTOR