Jal Jeevan Mission (JJM)_Athirampuzha_5th SLSSC_Supply and Installation of 750 KVA Indoor Transformer for Power enhancement and allied works at WTP, Medical College Campus Kottayam _General Civil Work

Amount

Construction of Pump House & Transformer room

2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1:Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

100.2.2:Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10m2 on plan), including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m, in Medium Rock where Blasting is Prohibited.

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

6.1.1:Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.2.1:15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement :4 fine sand)

13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.9.1:Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.44.1:Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)

OD118968/2023-2024:Supply and commissioning of portable Monkey type Hoist with capacity upto 500kg, with lifting height of 3m, 5HP Motor, 415V 50Hz all mounted on a suitable medium vehicle patform for easy shifting of equipments and materials whenever required with complete set as per standards"

OD118969/2023-2024:Supplying conveying and fixing steel I section (2 Nos ) ( 250 mm x 125 mm x 6.9 mm ) Mild steel of 9.7 m on curbs of the newly constructed pump house to access free to and fro motion of over head crane .

2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

OD119460/2023-2024:Cost of Crompton Laser Ray Neo 2 Feet 10W LED Batten (Cool Daylight)

10.6.3:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x0.90 mm M.S. laths with 0.90 mm thick to cover

10.7:Providing and fixing ball bearing for rolling shutters.

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

100 HP Pump Set

Supply and Installation of 750 KVA Indoor USS and connected Electrical works at WTP Campus Medical College Kottayam

OD117357/2023-2024: 11KV Three Panel Switchgear(Indoor)-Supply, erection, testing and commissioning of 11KV, 630A,35 kA3sec totally enclosed, single bus bar, floor mounting in metal clad, indoor extensible type flush mounted horizontal isolation and draw out type vacuum circuit breaker fitted with manual/motor operated spring charge mechanism with 230V AC motor and motor control switch,shunt trip coil of 24 volt DC auxiliary contact 6NO+6NC, Mechanical ON/OFF indicator,Mechanical operation counter,Anti pumping feature,Automatic safety shutters and push button etc, four panel system (1 no. VCB as incomer and 2 Nos. VCBs as outgoings) suitable for installation in 3 phase , 3wire, 50Hz. AC,11kv, effectively earthed supply system,comprising of motorised and spring assisted, independent, trip free closing mechanism and all metering equipments, MC61A numerical protective relays etc. draw out type resin cast 11kv/110volt <br> PT with contoling fuses for both side .2s class Dual core CT , LED panel lamps , panel heaters etc complete as approved by Kerala Electrical Inspectorate and relevant standards. Armoured multi core 2.5 Sqmm copper control cables shall be used for all external & internal interconnections. The cost of control cables both internal and external shall be included in the cost of HT panel, 11KV Switchgear (Indoor). The incomer VCB shall be provided with tariff TOD meter with 3 nos 60/ 5 Amps class 0.2S 15 VA CT and 3 nos 11KV / 110 Volt class 0.2 PT etc as per attached specification including sealing and locking arrangement all civil works such as transportation , handling making suitable foundations etc charges for testing calibration by TMR charges for erection and commissioning is included complete.

OD117362/2023-2024:Supply Installation, testing and commissioning of unitised substation 750KVA, 11KV/433V, 3-phase, 50Hz, Cast resin dry type indoor Transformer with all standard accessories linked with a 12kV Load break SFU with HRC fuse shunt trip, remote tripping mechanism, seal off bushings etc. including all control wiring, testing of relays/CTs etc. installation shall be done as per standards and as per CEA regulations applicable.

OD117366/2023-2024: Supply and Laying 11kV, 3C x 300 sq.mm XLPE power cable of 11 KV grade direct in duct/ trench ground including excavation, sand cushioning, protective covering and refilling the trench etc as required complying to specifications and standards. From DP Structure to VCB Panel And VCB panel to 750kVA USS including all materials for laying

OD165509/2023-2024:supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable fo 3 core,300 sqmm XLPE aluminium conductor cable of 11 KV grade as required :

OD117372/2023-2024:Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 3 core, 300 sqmm XLPE aluminium conductor cable of 11 KV grade as required :

OD117426/2023-2024:Supply, Design, Fabrication, Erection, Testing and Commissioning of following cubicle type, fully compartmentalised LT switchboards dust tight and vermin proof, fabricated out of 14/16 SWG CRCA sheet, chemically treated and powder coatd with 2 coats approved shade. The Panel boards shall have an IP rating of IP 4. The switchboards should have a set of suitably rated TPN Aluminium busbars with the specified current and ault level, insulated with heat shrinkable, color coded PVC sleeves and supported using DMC/SMC pillar or Finger type busbar supports.The design shall be as per the standards of the State Electrical Inspectorate. All indication lamps should be LED type, all MCCBs shall be with rotary operating handle.

OD117439/2023-2024:Supply, Design, Fabrication, Erection, Testing and Commissioning of following cubicle type, fully compartmentalised LT switchboards dust tight and vermin proof, fabricated out of 14/16 SWG CRCA sheet, chemically treated and powder coatd with 2 coats approved shade. The Panel boards shall have an IP rating of IP 4. The switchboards should have a set of suitably rated TPN Aluminium busbars with the specified current and ault level, insulated with heat shrinkable, color coded PVC sleeves and supported using DMC/SMC pillar or Finger type busbar supports.The design shall be as per the standards of the State Electrical Inspectorate. All indication lamps should be LED type, all MCCBs shall be with rotary operating handle.

OD117441/2023-2024:DISTRIBUTION BOARDS Supply installation testing and comissioning of reputed make 4way vertical distribution boards consisting of 100A Isolator as incommer and suitably rated TP MCBs of rating 16A to 32A, 4nos as per standards. - for VDB

OD117443/2023-2024:Supply installation testing and comissioning of reputed make TPN 6way distribution board consisting of 32A/30mA 4P ELMCB as incommer and18 nos of 6A SP MCBs of as per standars. - for LDB1 & 2.

OD117461/2023-2024:Supply installation testing and commissioning locable on/off push button of reputed make for emergency trip of HT incomer supply

OD117463/2023-2024:Supply and Laying reputed make 4Rx3.5Cx 400 sqmm 1.1kV grade armoured aluminum conductor XLPE cable as per standards (USS to MSB, MSB to SSB1

OD117473/2023-2024:Supply and Laying reputed make 3.5x185 sqmm 1kV grade armoured aluminum conductor XLPE cable as per standards (SSB 1 to 100Hp Motors 1&2 and APFC)

OD117497/2023-2024:Supply and Laying reputed make 3.5x 95 sqmm 1kV grade armoured aluminum conductor XLPE cable as per standards SSB 1 to 75Hp Motors

OD117499/2023-2024:Supply and Laying reputed make 3.5x 70 sq mm 1kV grade armoured aluminum conductor XLPE cable as per standards SSB 1 to 60Hp Motors

OD117536/2023-2024:Supply and Laying reputed make 3.5 x 35 sq mm 1kV grade armoured aluminum conductor XLPE cable as per standards SSB 1 to VDB, to 30HP Air blower)

OD117546/2023-2024:Supply and Laying reputed make 3 x 10 sqmm 1kV grade armoured aluminum conductor XLPE cable as per standards(VDB to backwash 10 Hp Motor)

OD117552/2023-2024:Supply and Laying reputed make 2x 2.5 sqmm 1kV grade armoured copper conductor XLPE cable as per standards (Apfc,remote control, neutral CT to EFR)

OD117556/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for 3.5 X400 sq mm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117571/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for 3.5 X185 sq mm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117575/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for3.5 X95 sqmm XLPE aluminium conductor cable of 1.1 KV grade as required. DAR 2018- 9.1.24 - cost index included

OD117583/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for3.5 X70 sqmm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117588/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for3.5 X35 sqmm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117591/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for3 X10 sqmm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117594/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for 3.5 x10 sq mm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117597/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for 2 X2.5 sq mm XLPE aluminium conductor cable of 1.1 KV grade as required.

OD117673/2023-2024:Earthing with G.I. earth plate1200 mm X1200 mm X 12 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. . (All civil works shall be done by the contractor) as per standards of BS 3048 and CEA regulations

OD117674/2023-2024:supply and laying 50 x6mm hot dip GI strip for earthing the system

OD117715/2023-2024:Providing and fixing 25 mm X 5 mm G.I. hot strip for connections etc. as required. (for Panel earthing)

OD117760/2023-2024:supply and laying of SWG no.10 copper wire for VDB earthing

OD117845/2023-2024:Supply and fixing of MS angle/supports for cable trays for clamping of cables in trenches/ through walls and trusses etc. Angles and plates should be painted one coat of primer and two coat of enamel paint as required as per KEI standards

OD117882/2023-2024:Supply and fixing 6kg DCP fire extinguisher

OD117886/2023-2024:Supply and installing 2 Fire buckets with single stand

OD117889/2023-2024:Supply and laying 11KV Rubber mat size of 1800 x1900 x12mm

OD117892/2023-2024:Supply and laying LT Rubber mat 2000mm x 1000mm x 6 mm

OD117898/2023-2024:Supply and fixing Shock treatment chart

OD117900/2023-2024:Supply and fixing first aid box with medicines

OD117920/2023-2024:Statutory Approval - Obtaining statutory approval from Eletrical Inspectorate including preparation of drawings, obtaining approval for the drawings arranging inspection of the installations and obtaining safety certificate etc.after completion of the work.The necessary statutory fees if any payable to the Electrical Inspectorate/ KSEB will be paid by KWA (Note: Scheme approval from the Electrical Inspectorate has to be obtained before supplying the equipments. Payment for the supply of materials will be released only on production of scheme Approval.)"

Bidder Name

Tesla Heavy Electricals Pvt. Ltd.