Construction Work of R.C.C. Road With Rajula Stone Footpath On Both Sides Of Road, RCC Divider With LED Light Pole With Light, Green Plantation Work In The Middle Of The Road (Part-1), Anganwadi, RCC Pipe Drainage Line, PVC Pipe Line, Solar LED Street Light and Bore With Submersible Pump as Per Various Location Chart At, Rajula, Dist.: Amreli Under District Mineral Foundation Year-2025-26

NAME OF WORK:-CONSTRUCTION WORK OF R.C.C. ROAD WITH RAJULA STONE FOOTPATH ON

BOTH SIDES OF ROAD, RCC DIVIDER WITH LED LIGHT POLE WITH LIGHT, GREEN PLANTATION

WORK IN THE MIDDLE OF THE ROAD (PART-1), ANGANWADI, RCC PIPE DRAINAGE LINE, PVC

PIPE LINE, SOLAR LED STREET LIGHT AND BORE WITH SUBMERSIBLE PUMP AS PER VERIOUS

LOCATION CHART, AT. RAJULA

TOTAL AMOUNT PUT TO TENDER

TOTAL AMOUNT PUT TO TENDER

PERCENTAGE RATE TENDER

Sr.No. Schedule Amount

1 Schedule - "B"- 1

2 Schedule - "B"- 2

3 Schedule - "B"- 3

4 Schedule - "B"- 4

5 Schedule - "B"- 5

6 Schedule - "B"- 6

7 Schedule - "B"- 7

8 Schedule - "B"- 8

9 Schedule - "B"- 9

10 Schedule - "B"- 10

11 Schedule - "B"- 11

12 Schedule - "B"- 12

13 Schedule - "B"- 13

14 Schedule - "B"- 14

15 Schedule - "B"- 15

16 Schedule - "B"- 16

Total Amount Rs……...

Total Amount Rs……...

I/We am/are willing to carry out the work @ ________% Above / Below_____________Percentage (should

be writen in figures and words) of the Estimated rates mentioned above amount of my / our Tender works

Estimated Amount Estimated Amount

Put to Tender Rs. 4,73,37,348=00 Put to Tender Rs. 4,73,37,348=00

Add % Rs. Deduct %Rs.

Total Rs. Total Rs.

(In Words (In Words

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDING, LAYING, JOINTING 900MM R.C.C. PIPE GUTTER

LOCATION :- Ward No.7, Bidikamdar, Near Rameswar Hanumanji Temple, Rajula.

SCHEDULE - "B-1"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation upto 1.5M depth including sorting out and

stacking of useful materials and disposing of the excavated stuff upto

all lead. (A) Loose or soft soil 39.00 122.93 Cumt

(B) Dense or Hard soil 97.50 157.15 Cumt

(C) Hard Murrum 39.00 268.92 Cumt

(D) Soft rock not required Blasting 19.50 276.23 Cumt

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete 13.00 481.80 Cumt

Providing, laying (to level or slopes) and jointing reinforced concrete

light duty non-pressure pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for collar joints including

testing of joints complete.(D) 900mm dia NP2 Class 130.00 2212.24 Rmt

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-

coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of

neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With

230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. /Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm

diameter sewer. incl. excavation work 10.00 19350.08 No

Filling around the pipes with murrum including dressing, tampering

etc. complete. 180.80 86.03 Cumt

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDING, SUPPLYING, LOWERING, LAYING AND JOINTING OF 300MM RCC PIPE

LOCATION :- Ward No.3, Vadli Road Gutterline Work, Rajula.

SCHEDULE - "B-2"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Providing and supplying ISI Standard R.C.C. pipes in standard

lengths of following class and diameter suitable for either collar joints

or rubber ring joints including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. (IS - 458/

1989) Note : One collar should be supplied with each full length plain

ended RCC pipe, cost included in rates below. One rubber ring

should be supplied with each full length socketed pipe, cost included

in rates below. 10.1 (D) Class NP-3 Test Pressure 0.7 kg/Sqcm.

Providing and constructing Sewer manholes, scraper manholes and

unit house connection chamber, as per the type design in brick

masonary in C.M. 1:5 and outsice plastering in C. M. 1:3 necessary

100mm coping with reinforcement in R.C.C.M. 200 fixing C. I. steps

and fixing manhole frame and covers (But excluding supply of

manhole frame and covers) over manholes and house connection

chambers and fixing Manhole covers (but excluding supplying of

manhole covers) over scraper manhole etc. complete, providing and

fixing safety chain wherever necessary as per the stipulations in the

type desing comp. as per latest CPHEEO manual (incl. excavation) a)

Manhole type 'A' - Circular, having inside diameter of 1200mm

for depth up to 1.50m (For 150 mm to 500mm dia. sewers).

Manhole type "A" as above but upto 1.0m depth

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at

store or at site of work precast RCC M.200 Frame & cover suitable to

drainage M.H. and as per type design & Drawing including cost of

reinforcement M.S. Angles or Flate, curring mold work etc.Heavy

Duty Frame Suitable for 50cm opening of MH 12.00 1121.00 No

Cover Suitable for 50cm opening of MH 12.00 1173.00 No

Providing and supplying ISI marked only Standard length Stoneware

pipes in standard lengths of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. (IS - 651 / 1989) 11.1 Class A 100mm dia

Excavation for pipe line trenches incl. all safety provisions using site

rails and stacking excavated stuff up to a lead of 90 mts. cleaning the

site etc. complete for lifts and strata as specified. # 0.00 to 1.50m

300mm dia a) In all sorts of soil and soft murrum (20%) 60.60 89.00 Cumt

b) In hard murrum, boulders Incl. macadam road (50%) 151.50 135.00 Cumt

c) In soft rock and / or masonry in CM or L M or (30%) 90.90 163.00 Cumt

Providing bedding incl. ramming, watering, levelling, consolidationg

etc.. Complete as per standard and instruction of engineer in charge

As above with selected excavated earth available near site 14.00 60.00 Cumt

Item No. & Description Quantity Rate Per Amount

Lowering, laying and jointing R. C. C. pipes with gasket joint of

following diameters in proper position, grade and alignment as

directed by Engineer-in-charge including conveyance from stores to

site of work, labour, giving hydraulic testing as per ISI code, etc

complete including cost of jointing materials. R.C.C. NP-3 300mm dia

Lowering, laying and jointing Stone Ware pipes of following diameters

with cement joints in C. M. 1:1 proportion in proper position, grade

and alignment as directed at all level by Engineer-in-charge including

conveyance from stores to site of work, Jointing material, etc comp.

100mm Dia 60.00 58.00 Rmt

Refilling the pipe line trenches including ramming, watering,

consolidating & disposal of surplus stuff as directed within a radius of

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDING, LAYING, JOINTING 300 MM R.C.C. PIPE GUTTER

LOCATION :- Ward No.7, Old Khakhbai Road, Khodiyarnagar, Various Street Of Near Policeline, Rajula.

SCHEDULE - "B-3"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation upto 1.5M depth including sorting out and

stacking of useful materials and disposing of the excavated stuff upto

all lead. (A) Loose or soft soil 90.00 122.93 Cumt

(B) Dense or Hard soil 225.00 157.15 Cumt

(C) Hard Murrum 90.00 268.92 Cumt

(D) Soft rock not required Blasting 45.00 276.23 Cumt

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete 30.00 481.80 Cumt

Providing, laying (to level or slopes) and jointing reinforced concrete

light duty non-pressure pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for collar joints including

testing of joints complete.(D) 300mm dia NP2 Class 300.00 434.28 Rmt

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-

coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of

neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With

230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm

diameter sewer. 16.00 19350.08 No

Filling around the pipes with murrum including dressing, tampering

etc. complete. 391.20 86.03 Cumt

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDING, LAYING, JOINTING 300 MM R.C.C. PIPE GUTTER

LOCATION :- Ward No.7, Telephone Exchange Office, Kasturba Chhatralay To Bypass Rajula.

SCHEDULE - "B-4"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation upto 1.5M depth including sorting out and

stacking of useful materials and disposing of the excavated stuff upto

all lead. (A) Loose or soft soil 99.00 122.93 Cumt

(B) Dense or Hard soil 247.50 157.15 Cumt

(C) Hard Murrum 99.00 268.92 Cumt

(D) Soft rock not required Blasting 49.50 276.23 Cumt

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete 173.00 481.80 Cumt

Providing, laying (to level or slopes) and jointing reinforced concrete

light duty non-pressure pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for collar joints including

testing of joints complete.(D) 300mm dia NP2 Class 330.00 434.28 Rmt

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-

coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of

neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With

230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm

diameter sewer. 12.00 19350.08 No

Filling around the pipes with murrum including dressing, tampering

etc. complete. 290.30 86.03 Cumt

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDEING, LOWERING, LAYING AND JOINTING 450MM R.C.C. PIPE LINE

LOCATION :- Mafatpara Bapasitaram OttaTo Bachubhai Pancharvala's Shop,Rajula.

SCHEDULE - "B-5"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation upto 1.5M depth including sorting out and

stacking of useful materials and disposing of the excavated stuff upto

all lead. (A) Loose or soft soil 150.00 212.52 Cumt

(B) Dense or Hard soil 150.00 272.56 Cumt

(C) Hard Murrum 37.50 465.13 Cumt

(D) Soft rock not required Blasting 37.50 532.90 Cumt

Supplying and fixing reinforced concrete heavy duty non-pressure

pipes with collars for culverts including setting and joining the pipes in

C.M. 1:2 watering and laying (To level of slops of I.S. 458 /

Class NP3 casted by vertically vibrated technology of following

internal diameter. (i) 450 mm dia. 250.00 1462.00 Rmt

Filling around the pipes with murrum including dressing, tampering

etc. complete. 278.90 86.03 Cumt

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-

coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of

neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i) Inside size

900mm x 1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With

230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for

150mm diameter sewer. 15.00 19349.63 No

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDING, SUPPLYING, LOWERING, LAYING AND JOINTING OF 450MM RCC PIPE

LOCATION :- Ward No.6,New Court Building To Thomas School,Rajula .

SCHEDULE - "B-6"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Providing and supplying ISI Standard R.C.C. pipes in standard

lengths of following class and diameter suitable for either collar joints

or rubber ring joints including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. (IS - 458/

1989) Note : One collar should be supplied with each full length plain

ended RCC pipe, cost included in rates below. One rubber ring

should be supplied with each full length socketed pipe, cost included

in rates below. 10.1 (D) Class NP-3 Test Pressure 0.7 kg/Sqcm.

Providing and constructing Sewer manholes, scraper manholes and

unit house connection chamber, as per the type design in brick

masonary in C. M. 1:5 and outsice plastering in C. M. 1:3 necessary

100mm coping with reinforcement in R.C.C.M. 200 fixing C. I. steps

and fixing manhole frame and covers (But excluding supply of

manhole frame and covers) over manholes and house connection

chambers and fixing Manhole covers (but excluding supplying of

manhole covers) over scraper manhole etc. complete, providing and

fixing safety chain wherever necessary as per the stipulations in the

type desing comp. as per latest CPHEEO manual (incl. excavation)

a) Manhole type 'A' - Circular, having inside diameter of 1200mm

for depth up to 1.50m (For 150 mm to 500mm dia. sewers).

Manhole type "A" as above but upto 1.0m depth 30.00 12179.00 No

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at

store or at site of work precast RCC M.200 Frame & cover suitable to

drainage M.H. and as per type design & Drawing including cost of

reinforcement M.S. Angles or Flate, curring mold work etc. Heavy

Duty Frame Suitable for 50cm opening of MH 30.00 1121.00 No

Cover Suitable for 50cm opening of MH 30.00 1173.00 No

Providing and supplying ISI marked only Standard length Stoneware

pipes in standard lengths of following class and diameter including

all taxes, insurance, transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. (IS - 651 / 1989) 11.1 Class A 100mm dia

Excavation for pipe line trenches incl. all safety provisions using site

rails and stacking excavated stuff up to a lead of 90 mts. cleaning the

site etc. complete for lifts and strata as specified. # 0.00 to 1.50m

300mm dia a) In all sorts of soil and soft murrum (20%) 252.73 89.00 Cumt

b) In hard murrum, boulders Incl. macadam road (50%) 631.83 135.00 Cumt

c) In soft rock and / or masonry in CM or L M or (30%) 379.10 163.00 Cumt

Providing bedding incl. ramming, watering, levelling, consolidationg

etc.. Complete as per standard and instruction of engineer in charge

As above with selected excavated earth available near site

Item No. & Description Quantity Rate Per Amount

Lowering, laying and jointing R. C. C. pipes with gasket joint of

following diameters in proper position, grade and alignment as

directed by Engineer-in-charge including conveyance from stores to

site of work, labour, giving hydraulic testing as per ISI code, etc

complete including cost of jointing materials. R.C.C. NP-3 450 mm

Lowering, laying and jointing Stone Ware pipes of following diameters

with cement joints in C. M. 1:1 proportion in proper position, grade

and alignment as directed at all level by Engineer-in-charge including

conveyance from stores to site of work, Jointing material, etc comp.

Refilling the pipe line trenches including ramming, watering,

consolidating & disposal of surplus stuff as directed within a radius of

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- CONSTRUCTION WORK OF RCC GUTTER

LOCATION :- Ward No.7,Dolino Pat Area,Near Bhutnath Temple, Rajula.

SCHEDULE - "B-7"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto all

lead and sretta 68.40 157.15 Cumt

Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork but excluding reinforcement for

reinforced concrete work in (K) Vertical and Horizontial its upto floor

two level. 30.00 4907.31 Sqmt

Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- coarse

sand : 4- graded stone aggregates 20 mm nominal size) exposed work

with curing etc. complete including the cost of formwork but excluding the

cost of reinforsement for R.C.C work in (iii) Slabs having more than

cm and upto 13 cm. thickness 12.70 7454.03 Sqmt

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and Placing in position complete upto floor two level

Providing formwork of ordinary timber planking so as to give a rough finish

including centering shuttering strutting and propping etc. height of

Propping and centering below supporting floor to ceiling not exceeding

M. and removal of the same for in situ reinforced concrete and Plain

concrete work in. (C) Vertical surface such as walls (any thickness)

partitions and the like including attached buttresses & string course

& the like. 266.00 243.86 Sqmt

Providing and constructing rectangular brick masonry chamber for house

connection as per type design in brick masonry in C. M. 1:3 including M-

100 in foundation M-150 in benching inside plastering in C. M. 1:3 and

outside plastering in C. M. 1:3 coping in M200 and fixing RCC precast

manhole frame and covers, but exd. supply of manhole and cover etc.

complete incl. excavation. 6.00 8001.22 No

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

Plain Grill. 180.00 106.23 Kg

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- Providing, Supplying, Lowering, Laying and Jointing of PVC Pipe Line

LOCATION :- Water Sump Through Khakhabai Ghana Behind Bidikamdar Police Line, Rajula.

SCHEDULE - "B-8"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Providing and supplying in standard length ISI mark rigid unplasticised PVC

pipe suitable for potable water with ringfit joint including cost of ring as per IS

specification no. 4985/1988 including all local and central taxes,

transportation, freight charges, octrol, inspection charges, loading, unloading

conveyance to the departmental stores and incl. cost jointing material etc.

complete Test Pressure 6 Kg/cm² 110mm Ø PVC Pipe Line 1700.00 199.00 Rmt

Providing and supplying at store or site of work incl. freight, loading,

unloading, stacking, insurance and all taxes etc. complete PVC Tail Plece

with PVC Flange (ISI) Heavy duty (Moduled) 110mm dia 1.00 320.00 No

PVC Tee (Moulded) 110mm x 110mm dia 1.00 407.00 No

Excavation for pipe line trenches incl. all safety provisions using site rails and

stacking excavated stuff up to a lead of 90 mts. cleaning the site etc.

complete for lifts and strata as specified. 110mm Ø PVC Pipe Line Up to

1.50 mt. depth A) In all sorts of Soil and Soft murrum 765.00 89.00 Cum

B) In Hard Murrum 561.00 135.00 Cum

C) In Soft Rock 459.00 163.00 Cum

D) In Hard Rock 255.00 372.00 Cum

Lowering, laying and jointing PVC pipes and specials of following class and

diameter includind coat of converyance from store to site of works including

cost of labour, material, cement solvent, giving satisfactory hydraulic testing

as per ISI code. For 110mm Ø PVC Pipe Line 1700.00 19.00 Rmt

Refilling the pipe line trenches including ramming, watering, consolidating &

disposal of surplus stuff as directed within a radius of 3 km. 2023.85 22.00 Cum

Making job connection for old pipes in connecting the pipe line with existing

main and inserted of special incl. Cost of excavation cutting of pipes,

dewatering testing refitting etc. complete incl. all jointing materials etc. comp.

(excl. cost of specials pipes and fittings) 5.00 874.00 Job

Providing and cast in-situ ordinary cement concrete M-200(1:1.5:3) for

average 20cm thick wearing coat/c.c. pavement as directed in approved

fixed side formwork of steel channel including vibrating by screed-needle

vibrator and finishing by plate vibrator and finished in continuous operation

including providing of contraction joint at every 4.00mtr. and expansion joint

at interval of 40mtr. applying debonding strips, bitumen primer, bituminous

sealant and curing etc. complete. 178.50 5057.07 Cum

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- Providing, Supplying, Lowering, Laying and Jointing of PVC Pipe Line

LOCATION :- Durlabhnagar Water Carrying Pipe Line, Rajula.

SCHEDULE - "B-9"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipe

suitable for potable water with ringfit joint including cost of ring as per IS

specification no. 4985/1988 including all local and central taxes, transportation,

freight charges, octrol, inspection charges, loading, unloading conveyance to the

departmental stores and incl. cost jointing material etc. complete Test Pressure

6 Kg/cm² 90mm Ø PVC Pipe Line 150.00 139.00 Rmt

Providing and supplying at store or site of work incl. freight, loading, unloading,

stacking, insurance and all taxes etc. complete PVC Tail Plece with PVC

Flange (ISI) Heavy duty (Moduled) 90mm dia 2.00 236.00 No

PVC Tee (Moulded) 90mm x 90mm dia 2.00 324.00 No

Excavation for pipe line trenches incl. all safety provisions using site rails and

stacking excavated stuff up to a lead of 90 mts. cleaning the site etc. complete

for lifts and strata as specified. 90mm Ø PVC Pipe Line Up to 1.50 mt. depth

A) In all sorts of Soil and Soft murrum 67.50 89.00 Cum

B) In Hard Murrum 49.50 135.00 Cum

C) In Soft Rock 40.50 163.00 Cum

D) In Hard Rock 22.50 372.00 Cum

Lowering, laying and jointing PVC pipes and specials of following class and

diameter includind coat of converyance from store to site of works including cost

of labour, material, cement solvent, giving satisfactory hydraulic testing as per

ISI code. 90mm Ø PVC Pipe Line 150.00 17.00 Rmt

Refilling the pipe line trenches including ramming, watering, consolidating &

disposal of surplus stuff as directed within a radius of 3 km. 178.58 22.00 Cum

Making job connection for old pipes in connecting the pipe line with existing

main and inserted of special incl. Cost of excavation cutting of pipes, dewatering

testing refitting etc. complete incl. all jointing materials etc. comp. (excl. cost of

specials pipes and fittings) 5.00 850.00 Job

Crushed stone aggregate for machine cut hard quality (I) 40mm to 63mm size

all lead and lift 13.50 609.13 Cum

Supplying of Stone Dust all lead and lift 1.10 308.05 Cum

Providing and laying cement concrete 1:4:8 (1- Cement : 4-coarse sand : 8-

Machine Cut stone aggregates 40mm nominal size) and curing complete

including cost of formwork in (A) Foundation and Plinth 9.00 2896.68 Cum

Providing and cast in-situ ordinary cement concrete M-200(1:1.5:3) for average

20cm thick wearing coat/c.c. pavement as directed in approved fixed side

formwork of steel channel including vibrating by screed-needle vibrator and

finishing by plate vibrator and finished in continuous operation including

providing of contraction joint at every 4.00mtr. and expansion joint at interval of

40mtr. applying debonding strips, bitumen primer, bituminous sealant and curing

etc. complete. 54.00 5182.31 Cum

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer Chief Officer President

"DESIGN POINT" Rajula Nagarpalika Rajula Nagarpalika Rajula Nagarpalika

Amreli Rajula Rajula Rajula Sche B9-12

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- PROVIDING, ERECTING & INSTALLATION OF SOLAR LED STREET LIGHT

LOCATION :- Bidi Kamdar Area, Rajula.

SCHEDULE - "B-10"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Supplying and erecting LED Solar street lights with High power white

LEDs wattage of 1Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and polycarbonate optics/ lenses with

company mark/ name engraved or embossed with 36 hours battery

backup & MPPT 24V,7.5 A charge controller with 12 hours automatic

switch on/off with wind speed resistance 44 m/s asper IEC 61215 (C)

21W, IP-65, PV Module – 100W and 5 mtr poles complete erected 18.00 21364.53 Ea

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 45 x 45 x 100cm. Deep in below

ground level with plinth of 45 cm x 45cm (or 45cm dia x 45cm) high upper

ground level with necessary curing and finishing in approved manner. (for

Providing and erecting Pipe type earthing having 150 cms. long and

cms. dia. galvanised iron pipe with coupling and buch buried in specially

prepared earth pit complete with necessary 8 SWG earth wire. 18.00 368.65 Ea

For using salt and charcoal/ coke as required for pipe type earthing. 18.00 171.70 Ea

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- DRILLING OF 165MM DIA BORE WITH PROVIDING, SUPPLY, INSTALLATION, TESTING,

COMMISSIONING OF SUBMERSIBLE PUMP-1

LOCATION :- Dholiya Dungar Khodiyar Mandir Pase,Rajula.

SCHEDULE - "B-11"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Drilling of 200 / 215 mm dia. bore hole in overburden strata by DTH rig up to

required depth including fixing of 180 dia PVC casing pipe & further drilling

of 165 mm dia. bore hole in hard rock (trap etc.) strata by DTH drilling

method up to total depth of 300 meters including measuring the yield by V

notch and flushing of bore etc. complete in all districts of Zone V. (Casing up

to 12 Mts.) From 0 to 150 Mt. depth 450.00 264.00 Mtr

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming to

latest ISI including jointing materials. 180mm dia 6kg/cm² 400.00 571.00 Mtr

Providing and fixing bore plug having 100mm height made from M.S. plate

with 3 holes at equal distance on circumference for nut-bolts type, locking

arrangement with nuts-bolts & lock nuts of standard make complete. From

5mm thick MS plate suitable for 175mm dia pipe 1.00 654.96 No

Single phase borewell submersible pump motor set MOC: Casing: CI-

FG260, Impeller: Bronze & Shaft: SS:410 14) Cat.5.0, 40 LMP, 90 Mtr.

Supplying & installation Control panel board DOL / Star Delta starter suitable

for local & remote pump control application consisting of MPCB, overload

relay and contactors as per Type II coordination including digital voltmeter,

analogue ammeter with selector switch, run hour meter, required protective

relays & control accessories. C) D. O. L. up to 7.5 HP 1.00 8383.00 No

Supplying PVC insulated flat submersible copper cable as per detailed

technical specifications of R/C of GWSSB conforming to IS 694, IEC 60227 /

Manufacture, Supply and delivery of following ISI marked H.D.P.E. Pipes

(IS:4984/1985 with latest amendment) having material Grade PE-80 in

approximate 100 mtr. Coil length or as per GWSSB requirement with SS-

316 Nipple at both end having 11 TPI threading as per specification, press

fitted and bolted having nominal diameter as under as per detailed Technical

Specification. DN 32 PN-10 200.00 36.00 Mtr

Manufacture, supply and delivery of clamp made from M.S. plate with

holes on either side with nuts & bolts of standard make and suitable size.

450 mm x 50 mm x 10 mm flat suitable to 32 mm dia pipe 1.00 370.65 Pair

Lowering of single phase submersible pump set complete with required

length of HDPE pipe and cable in bore well and fitting of control panel board

including wiring work and satisfactory testing as per instruction of Engineer-

in-charge including carting of material to site. A) Upto 90 mtr. depth 1.00 700.00 Job

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer Chief Officer President

"DESIGN POINT" Rajula Nagarpalika Rajula Nagarpalika Rajula Nagarpalika

Amreli Rajula Rajula Rajula

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- CONSTRUCTION WORK OF ANGANWADI

LOCATION :- Ward No.7,Bidikamdar Anganwadi Cente No.17, Rajula.

SCHEDULE - "B-12"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Demolition of Brick work and stone masonry including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift.(ii) In Cement Mortar. 16.56 562.89 Cumt

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work 8.49 1082.34 Cumt

Dismentaling tiled of stone floors laid in mortar including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift. 56.52 49.11 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto all

lead and all sretta 43.44 157.15 Cumt

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand :

6 Machine cut stone aggregate 40mm nominal size ) and curring

complete including cost of formwork in (a) Foundation and plinth 9.39 3095.24 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (A) Foundation footing

base of column and mass concrete 24.38 4118.64 Cumt

Providing and laying controlled cement concrete M.200 exposed work

with curing etc. complete including the cost of formwork but excluding

the cost of reinforcement for R.C.C. work in (A) BEAMS :(ii) Having

cross-sectional area more than 0.08Sq.M and upto 0.12 Sq.M 7.76 9485.95 Cumt

Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2-

coarse sand : 4- graded stone aggregates 20 mm nominal size) for

R.C.C lintel including finishing smooth with,curing etc. complete

including the cost of formwork but excluding the cost of reinforcement. 0.99 8518.14 Cumt

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand

: 4- graded stone aggregates 20 mm nominal size) for reinforced

concrete Chhajjas not exceeding 10cm. thickness upto floor two level

including finishing the exposed surfaces with cement mortar 1:3 (1-

cement, 3 Fine sand) to give a smooth and even surface centering and

formwork and curing complete excluding cost of reinforcement. 0.39 6693.29 Cumt

Providing and laying controlled cement concrete M.200 exposed work

with curing etc. complete including the cost of formwork but excluding

the cost of reinforcement for R.C.C. work in (B) COLUMNS:(ii) Having

cross-sectional area more than 0.08 Sq.M and upto 0.18 Sq.M 3.20 12577.32 Cumt

Providing and laying controlled cement concrete M.150 and exposed

work with curing etc. complete including the cost of formwork but

excluding the cost of reinforsement for R.C.Cwork in (iii) Slabs having

more than 10 cm and upto 13 cm. thickness 6.59 7501.89 Cumt

Item No. & Description Quantity Rate Per Amount

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level. 4001.13 77.28 Kg

Filling available excavated earth (excluding rock) in trenches. plinth,

sides of foundations etc. in layers not exceeding 20 cm. in depth

consolidating each disposited layer by ramming and watering. 4.50 136.91 Cumt

Filling in foundation and plinth with murrum or selected soil in layers of

20 cm. thickness including watering, ramming and consolidating etc.

completed. 18.74 301.77 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 23.03 4245.09 Cumt

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement Mortar

1:3 (1 cement : 3 Sand) 90.14 195.42 Sqmt

Providing 10mm thick cement plaster in single coat on brick/ concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) 50.22 145.65 Sqmt

20 MM thick sand faced cement plaster on walls upto height 10meters

above ground level consisting of 12MM thick backing coat of Cement

Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing coat of Cement

Mortar 1:1 (1-Cement : 1-Sand) etc. complete 243.04 342.41 Sqmt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc. complete for light shade 50.22 1264.40 Sqmt

Providing and laying marble stone slab flooring over 20mm

(average)base of cement mortar 1:6 (1-cement : 6 coarse sand) and

jointed with gray cement slurry including rubbing and polishing complete.

(A) Marble slab 25mm thick 4.00 2231.50 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème

out upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and

oxalic acid etc. as directed. 50.22 779.70 Sqmt

Providing and mixing Dr. Fixit water proofing material in cement

concrete in mix proportion recommended b the manufacturers. (0.18

Kg./1 Sqmt.) 9.04 49.15 Lit/Kg

Provoding and fixing flush door shutters, solid core construction with

frame of first class hardwood with cross board and face veneer or

plywood face panels, including anodised alluminium butt hinges with

necessary screws. (B) Non-decorative type and block board core

anodised alluminium butt hinges in flush door shutters (2) 35 mm thick.

Item No. & Description Quantity Rate Per Amount

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm (of Jindal

Section no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track member

size 92mm x 31.75mm x 1.30mm (of Jindal Section no:8688,@ Wt.1.07

Kg/mt), vertical member of size 92mm x 31.75mm x 1.50mm (of Jindal

Section no:8933,@ Wt. 1.06 Kg/mt) with sliding shutters of horizontal

member size 40 mmx18mm x1.29mm (of Jindal Section no:8947@ wt.of

0.456 Kg/mt), vertical member of size 40mm x 18mm x 1.29 mm (of

Jindal Section no:8949 @ wt.of 0.456Kg/mt/ with 5 mm thick transparent

bronze colour tinted float glass/S.S. Mosquito Jali with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass fixing

to frame as per details etc 9.00 1583.95 Sqmt

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead. 7.20 36.74 Sqmt

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 7.20 92.20 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 140.36 82.85 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete 243.04 120.26 Sqmt

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white front

plate modules erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as directed. (a)

with medium class Rigid PVC pipe and accessories erected flushed

on wall/ceiling complete.Cat. III 10.00 449.45 No.

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%, CCT 3000 K to

6500K, Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency

> 85% as per approved vender list make (fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with integral

driver (ii) 12-14 Watts, Surge-2 KV, IP-20, conventional 4 feet Cat-lll

Item No. & Description Quantity Rate Per Amount

Providing & erecting Approved make Ceiling Fan with double ball

bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep

complete, canopy erected on existing hook or clamp with earthing [

Make shall be approved by Engineer in Charge] 1.00 1738.21 No.

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete on

terrace 1000.00 3.95 Litre

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nutsor by screws (A)

Plain Grill. 517.50 106.23 Kg

Providing and laying cement concrete M-200 and curing complete

including cost of formwork in (A) Wall Caps / Coping 0.95 5130.80 Cumt

Single phase borewell submersible pump motor set MOC: Casing: CI-

FG260, Impeller: Bronze & Shaft: SS:410 1.00 12824.00 No.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height including

covering the top with stone including providing vatas in C.M. 1:3 with

finishing curing etc. complete as directed. 2.00 3457.27 Each

Providing and Fixing Wooden wardrobe with 4 shelves size: H-1500X W-

1100X D-450mm, Finish of exterior / edge, PVC Edge Banding, Material

of Lamination in Top Section, Number of Doors: 2, Opening Mechanism

of Door(s), RFID Lock, Bar Handle, Approved as per choice of users

department and concern officers in charge as directed by the Architect/

Engineer. 5.00 20200.00 No.

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete. 19.15 481.80 Cumt

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- CONSTRUCTION WORK OF ANGANWADI

LOCATION :- Gokulnagar Anganwadi Center No.26, Rajula.

SCHEDULE - "B-13"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Demolition of Brick work and stone masonry including stacking of

serviceable materilas and disposal of unserviceable materials with all lead

and lift. (ii) In Cement Mortar. 32.68 562.89 Cumt

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work 7.66 1082.34 Cumt

Dismentaling tiled of stone floors laid in mortar including stacking of

serviceable materilas and disposal of unserviceable materials with all lead

and lift. 49.86 49.11 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto all

lead and all sretta 47.96 157.15 Cumt

Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand :

Machine cut stone aggregate 40mm nominal size) and curring complete

including cost of formwork in (a) Foundation and plinth 9.51 3095.24 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (A) Foundation footing

base of column and mass concrete 25.81 4118.64 Cumt

Providing and laying controlled cement concrete M.200 exposed work with

curing etc. complete including the cost of formwork but excluding the cost

of reinforcement for R.C.C. work in (A) BEAMS :(ii) Having cross-

sectional area more than 0.08Sq.M and upto 0.12 Sq.M 7.82 9485.95 Cumt

Providing and laying ordinary cement concrete 1:2:4 (1-Cement 2- coarse

sand : 4-graded stone aggregates 20mm nominal size) for R.C.C lintel

including finishing smooth with,curing etc. complete including the cost of

formwork but excluding the cost of reinforcement. 0.91 8518.14 Cumt

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand :

4- graded stone aggregates 20 mm nominal size) for reinforced concrete

Chhajjas not exceeding 10cm. thickness upto floor two level including

finishing the exposed surfaces with cement mortar 1:3 (1- cement, 3 Fine

sand) to give a smooth and even surface centering and formwork and

curing complete excluding cost of reinforcement. 0.26 6693.29 Cumt

Providing and laying controlled cement concrete M.200 exposed work with

curing etc. complete including the cost of formwork but excluding the cost

of reinforcement for R.C.C. work in (B) COLUMNS: (ii) Having cross-

sectional area more than 0.08 Sq.M and upto 0.18 Sq.M 3.51 12577.32 Cumt

Providing and laying controlled cement concrete M-150 and exposed work

with curing etc. complete including the cost of formwork but excluding the

cost of reinforsement for R.C.Cwork in (iii) Slabs having more than

cm and upto 13 cm. thickness 5.76 7501.89 Cumt

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level. 3897.11 77.28 Kg

Item No. & Description Quantity Rate Per Amount

Filling available excavated earth (excluding rock) in trenches. plinth,

sides of foundations etc. in layers not exceeding 20 cm. in depth

consolidating each disposited layer by ramming and watering. 7.15 136.91 Cumt

Filling in foundation and plinth with murrum or selected soil in layers of

cm. thickness including watering, ramming and consolidating etc.

completed. 16.20 301.77 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 24.42 4245.09 Cumt

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished even

and smooth in with Floating coat of neat cement. (i) cement Mortar 1:3 (1

cement : 3 Sand) 73.00 195.42 Sqmt

Providing 10mm thick cement plaster in single coat on brick/concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) 43.56 145.65 Sqmt

20 MM thick sand faced cement plaster on walls upto height 10meters

above ground level consisting of 12 MM thick backing coat of Cement

Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing coat of Cement

Mortar 1:1 (1-Cement : 1-Sand) etc. complete 266.20 342.41 Sqmt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete for light shade 43.56 1264.40 Sqmt

Providing and laying marble stone slab flooring over 20mm (average)base

of cement mortar 1:6 (1-cement : 6 coarse sand) and jointed with gray

cement slurry including rubbing and polishing complete. (A) Marble slab

25mm thick 2.90 2231.50 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème out

upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and oxalic

acid etc. as directed. 43.56 779.70 Sqmt

Providing and mixing Dr. Fixit water proofing material in cement concrete

in mix proportion recommended b the manufacturers. (0.18 Kg./1 Sqmt.) 7.84 49.15 Lit/Kg

Provoding and fixing flush door shutters, solid core construction with

frame of first class hardwood with cross board and face veneer or

plywood face panels, including anodised alluminium butt hinges with

necessary screws. (B) Non-decorative type and block board core

anodised alluminium butt hinges in flush door shutters (2) 35 mm thick. 7.25 1829.73 Sqmt

Item No. & Description Quantity Rate Per Amount

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm (of Jindal Section

no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track member size 92mm

x 31.75mm x 1.30mm (of Jindal Section no:8688,@ Wt.1.07 Kg/mt),

vertical member of size 92mm x 31.75mm x 1.50mm (of Jindal Section

no:8933,@ Wt. 1.06 Kg/mt) with sliding shutters of horizontal member

size 40 mmx18mm x1.29mm (of Jindal Section no:8947@ wt.of

Kg/mt), vertical member of size 40mm x 18mm x 1.29 mm (of Jindal

Section no:8949 @ wt.of 0.456Kg/mt/ with 5 mm thick transparent bronze

colour tinted float glass/S.S. Mosquito Jali with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as

per details etc 5.40 1583.95 Sqmt

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead. 4.32 36.74 Sqmt

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 4.32 92.20 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 116.56 82.85 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete 266.20 120.26 Sqmt

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (a) with medium class

Rigid PVC pipe and accessories erected flushed on wall/ceiling complete.

Cat. III 10.00 449.45 No.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%, CCT 3000 K to 6500K, Luminaire efficacy>

lumens/watt ,LED driver efficiency > 85% as per approved vender list

make (fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges

shown.) (A) Tube Light with integral driver (ii) 12-14 Watts, Surge-2

KV, IP-20, conventional 4 feet Cat-lll 3.00 238.36 No.

Providing & erecting Approved make Ceiling Fan with double ball bearing

ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep complete,

canopy erected on existing hook or clamp with earthing [ Make shall be

approved by Engineer in Charge] 1.00 1738.21 No.

Item No. & Description Quantity Rate Per Amount

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete on

terrace 1000.00 3.95 Litre

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nutsor by screws (A)

Plain Grill. 396.00 106.23 Kg

Providing and laying cement concrete M-200 and curing complete

including cost of formwork in (A) Wall Caps / Coping 1.20 5130.80 Cumt

Drilling of 200 / 215 mm dia. bore hole in overburden strata by DTH rig up

to required depth including fixing of 180 dia PVC casing pipe & further

drilling of 165 mm dia. bore hole in hard rock (trap etc.) strata by DTH

drilling method up to total depth of 300 meters including measuring the

yield by V notch and flushing of bore etc. complete in all districts of Zone

V. (Casing up to 12 Mts.) From 0 to 150 Mt. depth 92.00 264.00 Mtr

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming to

latest ISI including jointing materials. 21.00 571.00 Mtr

Providing and fixing bore plug having 100mm height made from M.S. plate

with 3 holes at equal distance on circumference for nut-bolts type, locking

arrangement with nuts-bolts & lock nuts of standard make complete.

Single phase borewell submersible pump motor set MOC: Casing: CI-

FG260, Impeller: Bronze & Shaft: SS:410 1.00 12824.00 No.

Supplying & installation Control panel board DOL / Star Delta starter

suitable for local & remote pump control application consisting of MPCB,

overload relay and contactors as per Type II coordination including digital

voltmeter, analogue ammeter with selector switch, run hour meter,

required protective relays & control accessories. C) D. O. L. up to 7.5 HP

Supplying PVC insulated flat submersible copper cable as per detailed

technical specifications of R/C of GWSSB conforming to IS 694, IEC

Manufacture, Supply and delivery of following ISI marked H.D.P.E. Pipes

(IS:4984/1985 with latest amendment) having material Grade PE-80 in

approximate 100 mtr. Coil length or as per GWSSB requirement with SS-

316 Nipple at both end having 11 TPI threading as per specification, press

fitted and bolted having nominal diameter as under as per detailed

Technical Specification. 21.00 36.00 Mtr

Manufacture, supply and delivery of clamp made from M.S. plate with

holes on either side with nuts & bolts of standard make and suitable size.

Lowering of single phase submersible pump set complete with required

length of HDPE pipe and cable in bore well and fitting of control panel

board including wiring work and satisfactory testing as per instruction of

Engineer-in-charge including carting of material to site. 1.00 700.00 Job

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height including

covering the top with stone including providing vatas in C.M. 1:3 with

finishing curing etc. complete as directed. 1.00 3457.27 Each

Item No. & Description Quantity Rate Per Amount

Providing and Fixing Wooden wardrobe with 4 shelves size: H-1500X W-

1100X D-450mm, Finish of exterior / edge, PVC Edge Banding, Material

of Lamination in Top Section, Number of Doors: 2, Opening Mechanism of

Door(s), RFID Lock, Bar Handle, Approved as per choice of users

department and concern officers in charge as directed by the Architect/

Engineer. 4.00 20200.00 No.

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete. 6.12 481.80 Cumt

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- CONSTRUCTION WORK OF ANGANWADI

LOCATION :- Ward No.3, Mafatpara Anganwadi Center No.21, Rajula.

SCHEDULE - "B-14"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work 6.38 1082.34 Cumt

Dismentaling tiled of stone floors laid in mortar including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift. 51.03 49.11 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto all

lead and all sretta 50.22 157.15 Cumt

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand :

6 Machine cut stone aggregate 40mm nominal size ) and curring

complete including cost of formwork in (a) Foundation and plinth 10.48 3095.24 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (A) Foundation footing

base of column and mass concrete 26.52 4118.64 Cumt

Providing and laying controlled cement concrete M.200 exposed work

with curing etc. complete including the cost of formwork but excluding the

cost of reinforcement for R.C.C. work in (A) BEAMS :(ii) Having cross-

sectional area more than 0.08Sq.M and upto 0.12 Sq.M 8.58 9485.95 Cumt

Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2-

coarse sand : 4- graded stone aggregates 20 mm nominal size) for R.C.C

lintel including finishing smooth with,curing etc. complete including the

cost of formwork but excluding the cost of reinforcement. 0.99 8518.14 Cumt

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand

: 4- graded stone aggregates 20 mm nominal size) for reinforced

concrete Chhajjas not exceeding 10cm. thickness upto floor two level

including finishing the exposed surfaces with cement mortar 1:3 (1-

cement, 3 Fine sand) to give a smooth and even surface centering and

formwork and curing complete excluding cost of reinforcement. 0.39 6693.29 Cumt

Providing and laying controlled cement concrete M.200 exposed work

with curing etc. complete including the cost of formwork but excluding the

cost of reinforcement for R.C.C. work in (B) COLUMNS: (ii) Having

cross-sectional area more than 0.08 Sq.M and upto 0.18 Sq.M 3.67 12577.32 Cumt

Providing and laying controlled cement concrete M.150 and exposed

work with curing etc. complete including the cost of formwork but

excluding the cost of reinforsement for R.C.Cwork in (iii) Slabs having

more than 10 cm and upto 13 cm. thickness 6.69 7501.89 Cumt

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level. 3697.28 77.28 Kg

Filling available excavated earth (excluding rock) in trenches. plinth,

sides of foundations etc. in layers not exceeding 20 cm. in depth

consolidating each disposited layer by ramming and watering. 7.20 136.91 Cumt

Item No. & Description Quantity Rate Per Amount

Filling in foundation and plinth with murrum or selected soil in layers of

cm. thickness including watering, ramming and consolidating etc.

completed. 19.07 301.77 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 25.25 4245.09 Cumt

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement Mortar

1:3 (1 cement : 3 Sand) 77.66 195.42 Sqmt

Providing 10mm thick cement plaster in single coat on brick/concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) 51.03 145.65 Sqmt

20 MM thick sand faced cement plaster on walls upto height 10meters

above ground level consisting of12 MM thick backing coat of Cement

Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing coat of Cement

Mortar 1:1 (1-Cement : 1-Sand) etc. complete 291.13 342.41 Sqmt

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete for light shade 51.03 1264.40 Sqmt

Providing and laying marble stone slab flooring over 20mm

(average)base of cement mortar 1:6 (1-cement : 6 coarse sand) and

jointed with gray cement slurry including rubbing and polishing complete.

(A) Marble slab 25mm thick 4.00 2231.50 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème out

upto surface using white cement including rounding off junctions and

extending them up to 15cm. along the wall, clearing with water and oxalic

acid etc. as directed. 51.03 779.70 Sqmt

Providing and mixing Dr. Fixit water proofing material in cement concrete

in mix proportion recommended b the manufacturers. (0.18 Kg./1 Sqmt.) 9.19 49.15 Lit/Kg

Provoding and fixing flush door shutters, solid core construction with

frame of first class hardwood with cross board and face veneer or

plywood face panels, including anodised alluminium butt hinges with

necessary screws. (B) Non-decorative type and block board core

anodised alluminium butt hinges in flush door shutters (2) 35 mm thick. 7.88 1829.73 Sqmt

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm (of Jindal

Section no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track member

size 92mm x 31.75mm x 1.30mm (of Jindal Section no:8688,@ Wt.1.07

Kg/mt), vertical member of size 92mm x 31.75mm x 1.50mm (of Jindal

Section no:8933,@ Wt. 1.06 Kg/mt) with sliding shutters of horizontal

member size 40 mmx18mm x1.29mm (of Jindal Section no:8947@ wt.of

0.456 Kg/mt), vertical member of size 40mm x 18mm x 1.29 mm (of

Jindal Section no:8949 @ wt.of 0.456Kg/mt/ with 5 mm thick transparent

bronze colour tinted float glass/S.S. Mosquito Jali with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass fixing

to frame as per details etc 9.00 1583.95 Sqmt

Item No. & Description Quantity Rate Per Amount

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead. 7.20 36.74 Sqmt

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 7.20 92.20 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 128.69 82.85 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete 291.13 120.26 Sqmt

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected, with necessary

Lamp holder/ceiling rose / H.D.Connector as directed. (a) with medium

class Rigid PVC pipe and accessories erected flushed on wall/ceiling

complete. Cat. III 10.00 449.45 No.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V, Power Factor

more than 0.95, THD < 15%, CCT 3000 K to 6500K, Luminaire efficacy>

85 lumens/watt, LED driver efficiency > 85 % as per approved vender list

make (fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges

shown.) (A) Tube Light with integral driver (ii) 12-14 Watts, Surge-2

KV, IP-20, conventional 4 feet Cat-lll 3.00 238.36 No.

Providing & erecting Approved make Ceiling Fan with double ball bearing

ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep complete,

canopy erected on existing hook or clamp with earthing [ Make shall be

approved by Engineer in Charge] 1.00 1738.21 No.

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete on

terrace 1000.00 3.95 Litre

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nutsor by screws (A)

Plain Grill. 474.00 106.23 Kg

Providing and laying cement concrete M-200 and curing complete

including cost of formwork in (A) Wall Caps / Coping 1.33 5130.80 Cumt

Item No. & Description Quantity Rate Per Amount

Drilling of 200 / 215 mm dia. bore hole in overburden strata by DTH rig up

to required depth including fixing of 180 dia PVC casing pipe & further

drilling of 165 mm dia. bore hole in hard rock (trap etc.) strata by DTH

drilling method up to total depth of 300 meters including measuring the

yield by V notch and flushing of bore etc. complete in all districts of Zone

V. (Casing up to 12 Mts.) From 0 to 150 Mt. depth 92.00 264.00 Mtr

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming to

latest ISI including jointing materials5 21.00 571.00 Mtr

Providing and fixing bore plug having 100mm height made from M.S.

plate with 3 holes at equal distance on circumference for nut-bolts type,

locking arrangement with nuts-bolts & lock nuts of standard make

complete. 1.00 654.96 No.

Single phase borewell submersible pump motor set MOC: Casing: CI-

FG260, Impeller: Bronze & Shaft: SS:410 1.00 12824.00 No.

Supplying & installation Control panel board DOL / Star Delta starter

suitable for local & remote pump control application consisting of MPCB,

overload relay and contactors as per Type II coordination including digital

voltmeter, analogue ammeter with selector switch, run hour meter,

required protective relays & control accessories. C) D. O. L. up to 7.5 HP

Supplying PVC insulated flat submersible copper cable as per detailed

technical specifications of R/C of GWSSB conforming to IS 694, IEC

Manufacture, Supply and delivery of following ISI marked H.D.P.E. Pipes

(IS:4984/1985 with latest amendment) having material Grade PE-80 in

approximate 100 mtr. Coil length or as per GWSSB requirement with SS-

316 Nipple at both end having 11 TPI threading as per specification,

press fitted and bolted having nominal diameter as under as per detailed

Technical Specification. 21.00 36.00 Mtr

Manufacture, supply and delivery of clamp made from M.S. plate with

holes on either side with nuts & bolts of standard make and suitable size.

Lowering of single phase submersible pump set complete with required

length of HDPE pipe and cable in bore well and fitting of control panel

board including wiring work and satisfactory testing as per instruction of

Engineer-in-charge including carting of material to site.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height including

covering the top with stone including providing vatas in C.M. 1:3 with

finishing curing etc. complete as directed. 1.00 3457.27 Each

Providing and Fixing Wooden wardrobe with 4 shelves size: H-1500X W-

1100X D-450mm, Finish of exterior / edge, PVC Edge Banding, Material

of Lamination in Top Section, Number of Doors: 2, Opening Mechanism

of Door(s), RFID Lock, Bar Handle, Approved as per choice of users

department and concern officers in charge as directed by the Architect/

Engineer. 2.00 20200.00 No.

Item No. & Description Quantity Rate Per Amount

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- CONSTRUCTION WORK OF ANGANWADI

LOCATION :- Ward No.1,Tavvakalnagar Anganwadi Center No.12,Rajula.

SCHEDULE - "B-15"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work 8.59 1082.34 Cumt

Dismentaling tiled of stone floors laid in mortar including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift. 57.33 49.11 Cumt

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

all lead and all sretta 36.66 157.15 Cumt

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse

sand : 6 Machine cut stone aggregate 40mm nominal size ) and

curring complete including cost of formwork in (a) Foundation and

plinth 8.44 3095.24 Cumt

Providing & Laying controlled cement concrete M-200 and curing

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (A) Foundation

footing base of column and mass concrete 22.23 4118.64 Cumt

Providing and laying controlled cement concrete M.200 exposed work

with curing etc. complete including the cost of formwork but excluding

the cost of reinforcement for R.C.C. work in (A) BEAMS :(ii) Having

cross-sectional area more than 0.08Sq.M and upto 0.12 Sq.M

Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2-

coarse sand : 4- graded stone aggregates 20 mm nominal size) for

R.C.C lintel including finishing smooth with,curing etc. complete

including the cost of formwork but excluding the cost of reinforcement.

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse

sand : 4- graded stone aggregates 20 mm nominal size) for

reinforced concrete Chhajjas not exceeding 10cm. thickness upto

floor two level including finishing the exposed surfaces with cement

mortar 1:3 (1- cement, 3 Fine sand) to give a smooth and even

surface centering and formwork and curing complete excluding cost

of reinforcement. 0.39 6693.29 Cumt

Providing and laying controlled cement concrete M.200 exposed work

with curing etc. complete including the cost of formwork but excluding

the cost of reinforcement for R.C.C. work in (B) COLUMNS:(ii)

Having cross-sectional area more than 0.08 Sq.M and upto

Sq.M 2.73 12577.32 Cumt

Providing and laying controlled cement concrete M.150 and exposed

work with curing etc. complete including the cost of formwork but

excluding the cost of reinforsement for R.C.Cwork in (iii) Slabs

having more than 10 cm and upto 13 cm. thickness 6.69 7501.89 Cumt

Item No. & Description Quantity Rate Per Amount

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level.

Filling available excavated earth (excluding rock) in trenches. plinth,

sides of foundations etc. in layers not exceeding 20 cm. in depth

consolidating each disposited layer by ramming and watering. 1.62 136.91 Cumt

Filling in foundation and plinth with murrum or selected soil in layers

of 20 cm. thickness including watering, ramming and consolidating

etc. completed. 19.07 301.77 Cumt

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional 20.01 4245.09 Cumt

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement

Mortar 1:3 (1 cement : 3 Sand) 81.67 195.42 Sqmt

Providing 10mm thick cement plaster in single coat on brick/ concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

20 MM thick sand faced cement plaster on walls upto height

10meters above ground level consisting of 12 MM thick backing coat

of Cement Mortar 1:3 (1-Cement : 3-Sand) and 8MM thick finishing

coat of Cement Mortar 1:1 (1-Cement : 1-Sand) etc. complete

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 (1 cement 6 coarse sand) on new surface

or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc.

complete for light shade 51.03 1264.40 Sqmt

Providing and laying marble stone slab flooring over 20mm

(average)base of cement mortar 1:6 (1-cement : 6 coarse sand) or

L.M. 1:1.5(1- lime putty : 1.5 - coarse sand) laid and jointed with gray

cement slurry including rubbing and polishing complete. (A) Marble

slab 25mm thick 4.00 2231.50 Sqmt

Providing and laying broken China Mosaic Flooring for Terrace using

12mm to 20mm broken pieces of glazed tiles to be laid over cement

mortar 1:3 to plain or slope and to be tempered to bring mortar crème

out upto surface using white cement including rounding off junctions

and extending them up to 15cm. along the wall, clearing with water

and oxalic acid etc. as directed.

Providing and mixing Dr. Fixit water proofing material in cement

concrete in mix proportion recommended b the manufacturers. (0.18

Kg./1 Sqmt.) 9.19 49.15 Lit/Kg

Item No. & Description Quantity Rate Per Amount

Provoding and fixing flush door shutters, solid core construction with

frame of first class hardwood with cross board and face veneer or

plywood face panels, including anodised alluminium butt hinges with

necessary screws. (B) Non-decorative type and block board core

anodised alluminium butt hinges in flush door shutters (2) 35 mm

thick. 9.45 1829.73 Sqmt

Providing and fixing window having extruded aluminum Colour

anodized section frame main outer size 95mm x 24mm x 1.17mm (of

Jindal Section no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track

member size 92mm x 31.75mm x 1.30mm (of Jindal Section

no:8688,@ Wt.1.07 Kg/mt), vertical member of size 92mm x

31.75mm x 1.50mm (of Jindal Section no:8933,@ Wt. 1.06 Kg/mt)

with sliding shutters of horizontal member size 40 mmx18mm

x1.29mm (of Jindal Section no:8947@ wt.of 0.456 Kg/mt), vertical

member of size 40mm x 18mm x 1.29 mm (of Jindal Section no:8949

@ wt.of 0.456Kg/mt/ with 5 mm thick transparent bronze colour tinted

float glass/S.S. Mosquito Jali with powder coated aluminum fittings

and fixtures and transparent silicon sealant glass fixing to frame as

per details etc 9.00 1583.95 Sqmt

Applying priming coat over new steel and other metel surface after

and including preparing the surface by throughly cleaning, oil,grease,

dirt and other foreign matter and scoured with brushes fine steel

wood, scrapers and sand paper with ready mixed priming paint

brushing red lead. 7.20 36.74 Sqmt

Painting two coats (excluding priming coat) on new steel and other

metal surface with enamel paint, brushing, interior to give an even

shade including cleaning the surface an even shade including

cleanicn the surface of all dirt, dust and other foreign matter. 7.20 92.20 Sqmt

Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth. 132.70 82.85 Sqmt

Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete 199.64 120.26 Sqmt

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push & accessories

and earth continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (a) with medium class Rigid PVC pipe

and accessories erected flushed on wall/ceiling complete.Cat. III

Item No. & Description Quantity Rate Per Amount

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as

a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%, CCT 3000 K to

6500K, Luminaire efficacy> 85 lumens/watt ,LED driver efficiency >

85% as per aaproved vender list make ( fitting required LM-79 & LM-

80 Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.) (A) Tube Light

with integral driver (ii) 12-14 Watts, Surge-2 KV, IP-20,

conventional 4 feet Cat-lll 3.00 238.36 No.

Providing & erecting Approved make Ceiling Fan with double ball

bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep

complete, canopy erected on existing hook or clamp with earthing [

Make shall be approved by Engineer in Charge] 1.00 1738.21 No.

Providing erecting and fixing double coated ISI water tank of required

capacity each with all necessary fittings and connection etc. complete

on terrace 1000.00 3.95 Litre

Providing and fixing M.S. grills of required pattern to wooden frames

of windows etc. with M.S. flats at required spacings and frame

alround, square or round bars with round headed bolts and nutsor by

screws (A) Plain Grill. 357.60 106.23 Kg

Providing and laying cement concrete M-200 and curing complete

including cost of formwork in (A) Wall Caps / Coping 0.59 5130.80 Cumt

Drilling of 200 / 215 mm dia. bore hole in overburden strata by DTH

rig up to required depth including fixing of 180 dia PVC casing pipe &

further drilling of 165 mm dia. bore hole in hard rock (trap etc.) strata

by DTH drilling method up to total depth of 300 meters including

measuring the yield by V notch and flushing of bore etc. complete in

all districts of Zone V. (Casing up to 12 Mts.) From 0 to 150 Mt.

depth 92.00 264.00 Mtr

Providing & Lowering of 180mm dia. x 6 Kg/cm² PVC Pipe confirming

to latest ISI including jointing materials5 21.00 571.00 Mtr

Providing and fixing bore plug having 100mm height made from M.S.

plate with 3 holes at equal distance on circumference for nut-bolts

type, locking arrangement with nuts-bolts & lock nuts of standard

make complete. 1.00 654.96 No.

Single phase borewell submersible pump motor set MOC: Casing: CI-

FG260, Impeller: Bronze & Shaft: SS:410 1.00 12824.00 No.

Supplying & installation Control panel board DOL / Star Delta starter

suitable for local & remote pump control application consisting of

MPCB, overload relay and contactors as per Type II coordination

including digital voltmeter, analogue ammeter with selector switch,

run hour meter, required protective relays & control accessories. C)

Supplying PVC insulated flat submersible copper cable as per

detailed technical specifications of R/C of GWSSB conforming to IS

Item No. & Description Quantity Rate Per Amount

Manufacture, Supply and delivery of following ISI marked H.D.P.E.

Pipes (IS:4984/1985 with latest amendment) having material Grade

PE-80 in approximate 100 mtr. Coil length or as per GWSSB

requirement with SS-316 Nipple at both end having 11 TPI threading

as per specification, press fitted and bolted having nominal diameter

as under as per detailed Technical Specification. 21.00 36.00 Mtr

Manufacture, supply and delivery of clamp made from M.S. plate with

3 holes on either side with nuts & bolts of standard make and suitable

size. 1.00 370.65 Pair

Lowering of single phase submersible pump set complete with

required length of HDPE pipe and cable in bore well and fitting of

control panel board including wiring work and satisfactory testing as

per instruction of Engineer-in-charge including carting of material to

site. 1.00 700.00 Job

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height

including covering the top with stone including providing vatas in C.M.

1:3 with finishing curing etc. complete as directed. 1.00 3457.27 Each

Providing and Fixing Wooden wardrobe with 4 shelves size: H-1500X

W-1100X D-450mm, Finish of exterior / edge, PVC Edge Banding,

Material of Lamination in Top Section, Number of Doors: 2, Opening

Mechanism of Door(s), RFID Lock, Bar Handle, Approved as per

choice of users department and concern officers in charge as

directed by the Architect/ Engineer. 4.00 20200.00 No.

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4

(1- Cement : 4 -coarse sand ) in foundation and plinth (B)

Conventional 2.93 629.83 Sqmt

Box cutting the road surface to proper slope and camber for making a

base for road work including removing the excavated stuff and

depositing on the road side slope as directed upto all lead and sretta

Crushed stone aggregate for machine cut hard quality (I) 40mm to

63mm size all lead and lift 17.16 609.03 Cumt

Supplying of Stone Dust all lead and lift 1.38 308.05 Cumt

Spreading the stone aggregate for rolling and W.B.M. including filling

the interstices to required camber and gradient (excluding spreading

of Blindage) (ii) 40mm to 63mm size aggreagates 17.20 262.23 Cumt

Spreading blindage or road crust filling the gaps in metal and leveling

to camber and gradient as directed.. 1.40 154.84 Cumt

Rolling and consolidating water bound macadam (except laterite and

Kankar) including watering not exceeding 150mm thickness (Main

layer including binding materials) including filling in depressions which

occur during the process. (A) With power roller

Item No. & Description Quantity Rate Per Amount

Providing and fixing pre-cast Rubber Dye / steel Dye inte locking

concrete block 60mm thick with grade of concrete M-300 pnumatic

compressed /vibrated mechanically and as per approved design

Confirming to IS 15658 : 2006 including 35mm Sand/stone dust/

greet layer for levelling and filling the joint with sand in proper line and

level as per guidlines of IRC : SP 63-2018 etc. Complete. 101.24 706.93 Sqmt

Providing cement vata (10cm. x 10 cm. size) quarter round in cement

mortar 1:1 including neat cement finishing, watering etc. complete.

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika

RAJULA NAGARPALIKA - RAJULA

SCHEME:- DISTRICT MINERAL FOUNDATION YEAR-2025-26

NAME OF WORK:- CONSTRUCTION OF RCC ROAD WITH RAJULA STONE FOOTPATH ON BOTH SIDES OF

ROAD & RCC DIVIDER WITH LED LIGHT POLE WITH LIGHT & GREEN PLANTATION WORK IN THE MIDDLE

OF THE ROAD (PART-1)

LOCATION :- Ahir Samaj Entrance Gate To Ambedkar Circle (Both Side), Station Road, At Rajula.

SCHEDULE - "B-16"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

RCC ROAD, RAJULA STONE FOOTPATH, RCC DIVIDER

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work 1201.50 1082.34 Cumt

Box cutting the road surface to proper slope and camber for making a

base for road work including removing the excavated stuff and

depositing on the road side slope as directed up to all lead and sretta 4476.90 109.41 Cumt

Filling in foundation and plinth with murrum or selected soil in layers

of 20cm. Thickness including watering, ramming and consolidating

etc. complete. 1692.00 301.77 Cumt

Crushed stone aggregate for machine cut hard quality (I) 40mm to

63mm size all lead and lift 1725.60 534.59 Cumt

Supplying of Stone Dust all Lead and lift 431.40 241.39 Cumt

Spredding the stone aggregate for roling and W.B.M. including filling

the interstices to required camber and gradient (excluding spreading

of blindage) (i) 40mm size aggregates. 1725.60 262.23 Cumt

Spreading blindage or road crust filling the gaps in metal and leveling

to camber and gradient as directed. (ii) Sand/Stone dust 431.40 154.84 Cumt

Rolling and consolidating water bound macadam (Except laterite and

kankar) including watering not exceeding 150mm thickness (main

layer including binding materials) including filling in depressions which

occur during the process. (A) With power roller 9500.10 15.87 Sqmt

Providing and filling in foundation with ordinary cement concrete M-

100 mix and providing necessary vertical pin headers including

formwork, vibrating, ramming and curing complete. 1764.10 3345.58 Cumt

Providing and fixing 100mm thick Hand cut RAJULA STONE floor as

per approved design laid on a Bed of 20mm thick cement mortar 1:3

(1 cement : 3 coarse sand) including of labour all tax, loading,

unloading, transportation in site size of Rajula Stone L 0.30 to 0.60 mt

W 0.30 to 0.45 mt D 80mm to 100 mm th. 1495.80 1394.81 Sqmt

Pointing on Uncoursed stone masonry with cement mortar 1:3 (1-

cement : 3-coarse sand) (A) Flush pointing 1495.80 108.57 Sqmt

Providing and fixing pre-cast concrete kerb stone of gray cement

based concrete block 30cm length, 30cm height and 15cm thick of

M250 grade concrete as per approved design and including

excavation for fixing in proper line and level, filling the joint with C:M

1:3 (1cement : 3fine sand) etc complete. 1720.80 374.92 Rmt

Item No. & Description Quantity Rate Per Amount

Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork but excluding reinforcement

for reinforced concrete work in (K) Vertical and Horizontial its upto

floor two level. 109.20 6348.86 Cumt

Providing and casting in situ controlled cement concrete M-250 for

average 75mm thick wearing coat laid as directed including tamping,

vibrating, finishing, curing and filling in joints with bitumen complete

and incl. admixtures Melamine Base/ Naphthalene Base using

Kg. per Cement Bage 2326.50 5129.79 Cumt

Providing and using of quartz base non metallic, dry shake natural

aggregate Concrete Surface Hardner of approved made and

manufacture @ 4 kg/ Sq.mt. 31020.00 30.30 Kg

Providing and using Polyester Fiber (12mm) with triangular or

equivalent cross section with specific gravity 1.35 to 1.40 (as a

secondary reinforcement) in concrete of any grade at the rate of

gms. (1-Packet of 125 gms.) per 50 kg. of cement consumption. 20939.00 26.26 Packet

Providing and laying M.S.side rail of road thickness with necessary

nut bolt plates, fixing as per width, applying plate vibrator, electric or

diesel on channal. comp. with V.D. system (Trimix) by using the all

nessesory equipment and material and machinery, such as running

creed vibrator on prelaid M.S. channel for levelling vaccume pupms,

floating and power trovelling etc. comp. 7755.00 97.97 Sqmt

Providing TMT Bar FE 500D reinforcement for R.C.C. Work including

bending, binding and placing in position complete upto floor two level. 38719.50 77.28 Kg

Supplying premoulded bituminous joint filler (I) 12mm Thick 747.30 553.79 Sqmt

Steel work, welded in built up sections framed work including cutting,

hoisting, fixing in position and applying a priming coat of red lead

paint.(A) In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross beams. Hip

and jack rafters, purlins conneted to common rafters and the like 41.96 9108.48 Qtl

Applying priming coat of over new steel and other metal surface after

and including preparing the surface by thoroughly cleaning, oil

grease, dirt and other foreign mater and scoured with brushes fine

steel wool, scrapers and sand paper with ready mixed priming paint

brushing red lead. 1919.90 36.74 Sqmt

Painting two coats (excluding priming coat) on new steel and other

metal surface with enamel paint, brusing interior to give an even

shade including cleaning the surface an even shade including

cleaning the surface of all dirt, dust and other foreign matter. 1919.90 92.20 Sqmt

Providing P.V.C. SWR pipes IS 13592 for water spouts 110mm dia

meter including necessary iron gratings as per drawings. 204.30 265.33 Rmt

7.00 mt Ht. LIGHTING POLE WITH LED LIGHT

Item No. & Description Quantity Rate Per Amount

Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/ 2633/ 4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile 35mm X

7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable

foundation (Included) as per details given by manufacturer

considering site requirement.

(E) 7Mtr. Long 70mm Top X 135mm bottom dia, 3mm thickness

with 225mm X 225mm X 16mm base plate, 4-M20 Bolts and

600mm long with necessary G.I. J Bolts . Approx Pole weight

Providing and erecting Street Light pole bracket comprising main B

Class GI pipe of 4.2cm/ require out side dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms. length and suitable for

76.5mm/ 80mm/ required size of pole top having sufficient fasteners

for fixing the brackets and having spread of 1.5.mtr. length with

110deg. with vertical plane & suitable welded stays, reducer and with

check nuts complete painted with one coat of Red oxide/ PU base

primer and two coats of Aluminium/ PU paint. paint with following nos

of arms. [B] Double Arm Bracket 1.5 Mtr 22.00 1002.93 Ea

Supplying and erecting LED street light/ Flood light fittings with high

power white LEDs wattage of 3 watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and

polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more

than 0.95, THD<10 %, CCT 3000 K to 5700K, Uniformity ratio >0.45,

Luminaire efficacy>100 lumens/watt. LED driver efficiency> 85% as

per approved vender list make.(fittings required LM-79 & LM-80

certificates) (NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. (ii)

above 48 to 60 Watts, Cat-III 44.00 4997.48 Ea

Supplying & erecting IP 55 grade following size section pillar

fabricated from joint less M.S. Sheet with angle iron legs made from

jointless M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement

concrete foundation and 45 cm high bricks work finishing with plaster

etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated

paint. section pillar roof should be without joint with water leakage

proof & tested as per IP 55 test & followed by IS 2147 of

(C) 60 X 30 X 45 cm section pillar fabricated from 16 Gauge MS

Sheet with angle iron legs 45 cm long made from 35 X 35 X 5 mm

thick MS angle. 1.00 1884.66 Ea

Supplying & erecting approved make time switch with single pole air

break contacts suitable for 230V. 15/16A. complete with self starting

motor driven clock ‘ON’&’OFF’ automatic arrangement at any

predetermined time during each 24 hours, With nickel cadmium

rechargeable battery backup erected as directed. 1.00 2354.31 No.

Item No. & Description Quantity Rate Per Amount

Supplying & erecting power contactor, AC 3 duty for time switch

complete erected as per direction Cat III (C) 4 pole 440V 16 Amp. 1.00 857.49 Ea

Providing and erecting HOT deep Galvanised iron strip wire 8 to

Providing and erecting Pipe type earthing having 150 cms.long and

2.5 cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

For using salt and charcoal / coke as required for pipe type earthing. 22.00 171.70 Ea

Supplying & erecting earth pit of minimum bore dia. 150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS3043-1987 made of corrosion free hot dipped

G.I. Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

values urrounded by highly conductive compound with high charge

dissipation suitable for following type of application swith chamber

and heavy duty cover. (A) (approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer In charge has to ensure

the value of earthing resistane mentioned intest Certificate) & having

back filling compound of (B) Inner chemical (CCM Compound) -

Resistivity: -0.2 ohm/ meter testing as per IEC 62561-2017, Voltage

drop :-<1 volt at no load & dry form, Sulphar content :-<2%

(B) Inner chemical (CCM Compound) -Resistivity: -0.2 ohm/ meter

testing as per IEC 62561-2017, Voltage drop :-<1 volt at no load & dry

form, Sulphar content :-<2% (C) Back fill Compound :-Earthing

compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. (a) For Electrical

Installation up to 440V in normal soil Length of pipe - 1 Mtr Back filling

compound - 1 Nos Bag of 15 Kg. 2.00 4591.46 Ea

Supplying and erecting Flexible PVC insulated multi strand multi core

1.1 kv grade ISI marked copper wires of following size to be erected

as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed 154.00 46.46 Mtr

providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark. Cat-III 22.00 270.68 Ea

Providing & erecting 415 V MCB Four Pole Switch for Lighting Load

(Bcurve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (b) 40 Amp., Cat III 1.00 638.32 Ea

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand/ Solid Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size of

cables (A) 4 core 4 Sq. mm 484.00 117.16 Mtr

Providing & laying approved make double walled corrugated pipes

(DWC) of polyethylene (conforming to IS 14930 II) with necessary

connecting accessories of same material at required depth in existing

trench for laying of cable. below ground/ road surface for enclosing

cable (A) 50mm dia. 500.00 62.62 Rmt

Item No. & Description Quantity Rate Per Amount

Making trench in soft soil of suitable width of 90 cm deep for laying

cable or locating the fault all over the run and back filling the same

and making the surface as normal ground. 488.00 55.55 Mtr

12 MT. HIGH MAST TOWER

Supplying, erecting, testing, commissioning approved make M.S.

Polygonal High Mast Pole having following general Specification. (a)

Polygonal Section fabricated from M.S. Plate confirms BSEN 10025 &

Hot deep galvanised minimum 65/86 micron (as per 2629/ 1985)

Lantern carriage with ring and rubber lines for erection of luminaries

of suitable site. (b) Maximum telescopic section not more than four

(c) Double drum gear pipe motorised winch with 6mm dia S.S. Rod

(For 16 mtr and above size) (d) Approved make L.E.D. aviation light=

1 No. Lighting arrestor= 1 No. with necessary wiring of 2.5 sq.mm

core ISI copper cable Unarmoured. (e) Bottom most section suitable

for mounting reversible motor and switchgears having door not more

than 1400mm x 300mm with waterproof gasket & hinges & locking

(f) Pole structure comprises suitable size of reversible motor, cable

and necessary switchgears.(g) bottom section shall have suitable size

of thickness supports ribs foundation bolts nuts etc.(h) Item not

comprises the cost of lanterns.(i) Necessary Cement Concrete

foundation as per IS including testing & commissioning of the entire

structure for following size of High Mast poles [CAT.II] [1] High

Mast 12 Mtr. TOP A/F 105 Mm, BOTTOM A/F 360mm, No. of Sec.

No.- 1, Bottom thickness- 3mm, Size Base Plate- 520 x 20mm

thick, Foundation Bolt Size M24 x 850mm, Qty- 6 Nos., Suitable

for mounting Fitting of Light- 6 Nos. 1.00 141616.14 Ea

Supplying and erecting LED street light/ Flood light fittings with High

power White LEDs wattage of 3 watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and

polycarbonate optics/ lenses, with toughened glass with company

mark/ name engraved or embossed 160 to 270 V, Power Factor more

than 0.95, THD<10 %, CCT 3000K to 5700K, Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/ watt. LED driver efficiency> 85% as

per approved vender list make (fittings required LM-79 & LM-80

certificates) (NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.) (B) Flood Light

(IP-65), Surgeprotection-4KV integral and, Light must have

440VAC line supply with over-voltage protection. (vii) above

to 250 watts Cat-lll 6.00 10263.62 Ea

Providing and erecting XLPE (IS:7098) (I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench/ pipe at road crossing or floor

of following size of cables. (A) 4 core 10 Sq. Mm 50.00 676.70 Mtr

GREEN PLANTATION

Providing & Fixing Cast Iron powder coating garden bench capicity

seat and finishing & fixing as per instruction etc. complete. 63.00 8080.00 Ea

Providing & Fixing Dustbin Outdoor Twin Wast Bins of Capicity

40x2ltr. Detail Given As per atteched specification complete. 20.00 1616.00 Ea

Supplying and stacking of good earth at site including royalty and

carriage upto 5 km lead complete (earth measured in stacks will be

reduced by 20% for payment) 124.60 811.78 Cumt

Item No. & Description Quantity Rate Per Amount

Mixing earth and sludge or manure in the required proportion

specified or directed by the Officer-in-charge. 124.60 56.25 Cumt

Supplying and stacking of well decayed cattle manure at site including

royalty and carriage upto 5km lead complete (Cattle manure

measured in stacks will reduced by 8% for Payment) 8.90 673.77 Cumt

Providing New Plantetion for Flower tree, Decorative outdoor plants

etc.including The work including cost of all materials, labour,

plantation with expertise, tranportation, loading, unloading, all taxes

etc. complete with Five years operation and maintanance after the

plantation. The work carried out as per directed by Engineer-in-

charge. Kashmiri Gulab, Red Jasud 50.00 45.45 Ea

Vasant Mori, Hemeliya 50.00 56.56 Ea

Movari 26.00 39.39 Ea

Parijat 26.00 67.67 Ea

Karen 26.00 102.01 Ea

Providing and fixing Tree Guard of required pattern to MS Angle

frames with M.S. flats at required spacing's and frame around with

SWG Jali, oil paint with all types of tax, loading, unloading,

transportation, etc. complete and dimension shown in the details

drawing attached herewith. 178.00 1212.00 Ea

DISPLAY SIGN BOARD

Buy HINLED DISPLAY SYSTEMS 5500 Nits Br. nline_Government e

Marketplace 1.00 212100.00 Ea

Providing and fixing Retro Reflective engineering grade board using

C.R.C. (M.S.) sheet 2mm, angle iron 75x75x6mm. Descaling and

degreasing the board as per requirement using epoxyprimer epoxy

paint and carrying retro reflactive process by screen painting as

directed etc. complete including transporting and fixing in C.C. 1:4:8

with necessary excavation curing etc. complete as per I.R.C type

design. (A) Engineer Grade 8.10 11887.43 Sqmt

ROAD PAINTING WORK

Providing and laying of Hot applied Thermoplastic compound 2.5 mm

thick including Reflectorising Glass Beads @ 250 gms per sqm area,

thickness of 2.5 mm is exclusive of surface applied glass beads as

per IRC : 35 & finished surface to be level, uniform and free from

streaks and holes. 188.00 367.72 Sqmt

Supplying and fixing cat eye (Stimsonite) made out from Acrilo

beautile sterine injuction high compressed molding with reflector

made of MMC (prismatic type of size 12cm x 6cm x 2.5cm) provided

with bituminous adhesive 100g. with each unit for fixing. (High

Intensity grade) 376.00 375.72 No.

Total Amount Rs.........

Total Amount Rs.........

Stamp with Signature of Contractor

Consl.Engineer Engineer

"DESIGN POINT" Rajula Nagarpalika

Chief Officer President

Rajula Nagarpalika Rajula Nagarpalika