Development and maintenance work in the parks of Zone Ist-D area (ARC)

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand).

Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand).

Add extra for Random Rubble stone masonry with hard stone in Square or Rectangular pillars

Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete and no glass strips are used and not applying 2 coats of hot bitumen complete as per specifications. 50mm thick.

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick.

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge).

M-30, 60 mm thick to be used in non traffic areas like building premises, monument premises, land scapes, public gardens/ park, domestic drives, paths and patios, Embankment slopes, sand stabilization Area etc.( As per table 1 of IS 15658:2006 (B) Category „B‟ Denated only two side like I,Z,T shape etc. as per IRC SP 63:2004

Add extra over rates of item No. 17, if colored paver blocks are used

Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe:

Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. 150 mm Nominal bore of pipe

Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. 150 mm Nominal Bore.

S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: 150mm dia

S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set.

SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. 2.0 HP, 1-Ø, (7- 95)Mtr, (55-22) LPM

Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 for water supply suitable for submersible & jet pump with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . for vertical installation 40 mm OD 6 kg / cm2

Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 12mm (suitable up to 50 mm OD pipe)

Supply & drawing Wiring for sub mains ISI marked (IS:694) 1100 Volts grade PVC insulated flat twin core sheathed solid aluminium conductor with 10 SWG G.I. Support wire duly clipped etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 6.0 sq.mm

P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 6.0 Sq.mm 3 core flat / Round

Providing and fixing 3-layer PP-R (Polypropylene random coplymer ) pipes SDR 7.4 UV stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings and fixing the pipe with clamps at 1 metre spacing. This includes testing of joint complete as per direction of Engineer - in charge.( INTERNAL WORK- EXPOSED ON WALL) PN-16 Pipe, 32 mm OD

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : (-do-) 32mm nominal bore.

Providing, Laying & Jointing R.C.C. class NP-2 Non-Pressure pipes (IS : 458mark) of approved make with collars, jointed with C.M. 1:2 or having Spigot and socket ends with flexible rubber rings joint including testing of joints etc. complete : 200mm dia Internal

1000 mm dia

600 mm dia

300 mm dia

Supply of dry manure including loading unloading,transportation & stacking at site. Farm yard manure(organic)

Supply of Chemical Fertilizers at store in bags weighing not less than 50 kg each including loading unloading & transportation

Supply & Stacking good soil of earth at site complete including loading unloading & Transportation etc. Good soil of earth

Spreading of manure , good earth in required thickness (cost of manure and good earth to be separately )

Supply of PVC hose pipe of different sizes at store including transportation etc. complete.

Supply of different varities of tree/shrubs/climbers according to height and age of the plant at side including loading/unloading & transportation etc.complete Different flowering plants 900mm to1500mm

Different varieties of shrubs 600mm to 900 mm

Different varieties of climbers 900mm to 1500 mm

Supply of different varieties of bougainvillea in ply bags/earthen pot according to height growth and age of plant at site including loading unloading and transportation etc. complete Local variety of bougainvillea 600mm to 900mm

Supply of different varieties of palms in poly bags/earthen pot according to height growth and age of plant at site including loading unloading and transportation etc. complete. Fish tale palm 5 to 8 feet

T cycuss 3 feet 5 feet

Supply of different varieties of indoor plants in poly bags/earthen pot according to height growth and age of plant at site including loading unloading and transportation etc. complete Rubber plants etc

Different fycus plants tolairy 100mm to 125 cm height

Different champa 125 cm to 215 cm height

Ground Cover of various varieties. Golden durantain P.B(5”X6”) - 6”-1’

TecomaGoudichoudi in P.B(9”X11”) - 2’

Enarmi in P.B(5”X5”) - 1’

Laying of lawns including ploughing leveling breaking of clods manuring and removal of stones etc. (cost of manure or extra good earth to be paid separately )maintenance of lawn foe 30 days or more till the grass forms a thick lawns free from weeds and fit for moving in the duration of planting if lawn die some where the contractor will replant it at his own cost. in rows 7.5 cm apart in either direction

laosnd }kjk fuEu iztkfr;ksa ds ikS/kksa dh vkiwfrZ ,oa yxkukA ikS/kksa dh mapkbZ 5 eh- ls vf/kd gksuk pkfg;sA ikS/kk LoLFk gksuk pkfg,A laosnd }kjk ikS/kk jksi.k ls iwoZ izR;sd [kMMs esa vizqOM [kkn o vko';drkuqlkj dhVuk'kd Mkyuk gksxk ,oa ikS/kk yxkus ds i'pkr de ls de 20 ls 25 yh- ikuh izfr ikS/kk nsuk gksxkA dpukj 10 ls 12 QhV

xqyeksgj 10 ls 12 QhV

djat 10 ls 12 QhV

uhe 10 ls 12 QhV

`'kh'ke 10 ls 12 QhV

Providing and fixing benches with side panel casted in Cast Iron single piece and middle part is of mild steel. Approx. ht. is 700 mm and length is 1250 mm the carving work is as per enclosed drawing and details and instruction of engineer incharge.

S/F of following outdoor Gym (fitness) Equipment including excavation of foundation in all kind of soil/hard roack. construction of foundation as per requirement of Gym Equipment or atleast 0.40x0.40x0.60m size in RCC M-20 mix or as per direction of engineer in charge. Gym equipment should be as per enclosed drawing and design in special conditions folowing make Kilkari/Regal/Arihant/Arogyam. Double Bar: Features : -H-4'6", L-6'6", W-3' -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe Powder Coated 100-110 microns

Sit Up Board: Features : -H-3'9", L-4'6", W-2'1" -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe Powder Coated 100-110 microns

Double Surf Board: Features : -H-4'4", L-3'10", W-3'2" -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe -Powder Coated 100-110 microns - FRP Foot Rest

Sky Walker: Features : -H-4'8", L-5'1", W-1'8" -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns - FRP Seat & Foot Rest

Cross Trainer: Features : -H-5'3", L-4'5", W-1'11" -3 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns - FRP Seat & Foot Rest

Shoulder Builder Triple: Features : -H-6'3", L-4'8", W-3'6" -3 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns

Double Twister Seating : Features : -H-4'4", L-7'1", W-2'2" -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns

Ches Press Double: Features : -H-6'8", L-5'5", W-2'3" -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns - FRP Seat & Foot Rest

Rower Double: Features : -H-3'8", L-7'6", W-2'7" - 2x2 Inch Square CRCA Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns - FRP Seat & Foot Rest

Peck Deck Double: Features : -H-6'2", L-6'1", W-3,2" -3 Inch Dia, Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns - FRP Seat & Foot Rest

Leg Press Double: Features : -H-5'8", L-6'4", W-1'7" -4 Inch Dia. Galvanized Steel Pipe -Handle 1/1.25 inch Dia. M.S. Pipe - Powder Coated 100-110 microns - FRP Seat & Foot Rest

Double Swing : Double Swing is suitable for 4 to 14 years Children and frame is made of NB pipes which should be following specifications : Area : 3.0 mtr x 2.50mtr. Safe play area : 4.0 mtr x 3.50 mtr. Height : 2.40 mtr. (on ground level) Leg support : 40mm NB pipes Top bar : 50mm NB pipe Seat : 9mm thick reinforced rubber (Non skid chequired top, bearing : Housing special casting heavy duty bail bearing, suspension : 7mm dia Electro Galvanized chain (ISO : 9001-2000 make)

Single See Saw : The Single See Saw suitable for 4 to 8 years children and made of MS pipes which should be following specification : Area Required : 1.50 mtr.x 3.0 mtr. Height : 0.90 mtr. Main Pipe : 50 NB pipe Plank : 40 NB pipe Handle : 20 NB pipe Seats : MS sheet (5mm thick) FRP (ISO : 9001-2000 make)

Parallel bars : Parallel Bars is suitable for 10 to 16 years children and main verticle frame made of 50mm NB pipe and horizontal bars made of 32mm NB pipes. Horizontal bars having length 2.10 mtr. and height is 1.20 mtr. On ground level. Total area of this parallel is 2.0 mtr. x 1.0 mtr.

Up and Down Ladder : Providing and Fixing of up-down ladder made out of MS pipe 40mm, 25mm size of length 10xheight should be less than 6' pipe should be ISI marked of heavy weight.

Wave Slide : The sliding chute of wave slide is made of 6mm thick fibre glass reinforced plastic. (Binani or equivalent make) with a smooth surface consist of 3 sliding mould of 2.00 ft. (approx). The platform made out of 10 gauge MS sheet and shall be supported on 33mm OD 14 gauge. The ladder shall be 60cm wide (approx) and will be made of 25mm NP pipe with 15mm dual steps. The slide shall be supported on three parallel supports of different length. the size of the slide above the ground level shall be as follows platform height 2.40, slide length 4.20m and slide width 0.50 mtr. (approx)

Supplying and fixing of Tree guard 1.5 metre including holding legs .9 m height angle 30x30x3 mm thick and also welded expanded mesh 50x50x16 guage in framework flat iron bedding 20x3 mm including to cross laps inside and outside welding iron bolts screws clips etc complete including complete number plate of plant.

Flyash Flyash Brick work with flyash Flyash Bricks of class designation 75 in superstructure above plinth level upto floor Three Level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricks Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Granular Sub-Base with Close Graded Material (Table:- 400-1) Providing laying spreading and compacting specified graded sand, gravel (crushed stone) as per Table 400-1,400-2 or any other course material as per design mix, as per CBR in sub base course including premixing the material at OMC in wet mix plant, carriage of mixed material spreading in uniform layers with motor grader F.E loader on a prepared base and compacting with vibratory roller to achieve desired density (as per I.S.2720) including all material, labor, machinery, lighting guarding, barricading and maintenance of diversion complete.[MoRTH specification : Clause 401]. By mechanical means. For Grading-III Material

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400-12 & 400-13 and MoRTH Specification Clause 406. By Mechanical Means with all lead

Construction of Jogging work on existing track using clay sand mix (design as approved by Rajasthan sports council) including grinding of clay and mixing by mechanical means preparation of bed. Laying clay mix mechanically (hydraulic system) and compacting using roller making surface leveled and even including cost of water hire charges all T&P complete in all respect as per direction of Engineer in charge.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300-1 and 300-2 with a lead upto 50 m as per MoRTH Specification Clause 305.3

Carriage of material from quarry / crusher to work site including loading, unloading and stacking all complete. Earth, Sand, Lime, Morrum manure or sludge for 10 KM

Floral Art Work in specific traditional style (Kota-Bundi/Mandna/Kishangarh/Nathdwara) in domes, arches, mehrabs etc as per Drawing under the direction of enineer incharge and as per approval of architect

Providing & making artistic/heritage painting with the using oil paint/apex ultima or equivalent exterior paint having anti algal and dust pick up resistance with finish as per direction of Engineer in charge on wall faces/panels etc. with approved colour in following patterns including painting base works of required exterior paint in approved quality/brand:- The Painting shall be based on themes related to flora & fauna like creepers flower pots, animals, birds & natural figures. As the work shall be at the level of similar to enclosed drawing ‘C’.

P & F Stone cladding/Flooring works dressed bansi paharpur stone 25mm thick in traditional style used in cladding/Flooring with pattern over 25 to 50 mm thick base in CM 1:6 including pointing with cement mortar 1:2 (cement : 2 stone dust) matche the shade of stone with joint thickness upto 1.5mm as per direction of engineer-in-charge.

Single piece of stone element with carving work in Bansi Paharpur stone includes stone pillar, stone base, todies and thabi etc carving work as per direction of engineer in charge

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. South (Red)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 0.63 mm thick with zinc coating not less than 275 gm/m2

Maintenace of Plants by the contractor including of pits/bids watering preparation of Thavala Hoeing weeding etc. & application of insecticides etc. & security if the plant die during maintenance contractor has to replace same height plant at his own cost. (For 12 months)

nwc dk la/kkj.k dk;Z & yxh gqbZ nwc dk la/kkj.k dk;Z esa [kjirokj fudkyuk] fu;fer flapkbZ djuk] [kkn Mkyuk ,oa e’khu ds }kjk fu;fer dVkbZ djuk rkfd nwc vPNh rjg ls fodflr gks ldsA ¼12 ekg ds fy;s½

Maintenance of Hedge, Climbers, Shrubs at parks including watering, trimming, preparation of thawala, manure and complete work. (For 12 Months)

Please Enable Macros to View BoQ information