CONSTRUCTION OF RISING MAIN PUMP HOUSE and ALLIED WORKS AT MOTHROWALA (DEEPNAGAR) DEHRADUN

Amount

Rising Main & Allied Works Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge

Bituminous road

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Excavation in soil mixed with single boulder etc. requiring the use of special T&P, if any, for pipe line trenches including lift unto 1.5 m and lead unto 50 m and refilling, watering, ramming of excavated earth in to the trenches and disposal of surplus earth unto 50 m from the center of the trenches.

Providing of all materials, carting from site store to site of work, lowering into trenches with true to alignment, Laying & Jointing of full lenght S&S Centrifugally cast (spun) Ductile iron pipes including supply of "EPDM" rubber gaskets conforming to IS : 5382/1985 with testing of pipe line complete.

D.I. Pipe conforming to IS: 8329/2000

D.I. Pipe S&S K-9

200 mm dia

Providing & Laying D.I. special of class K-12 suitable for push on jointing as per IS:9523-2001

Upto 600mm dia

Providing push on joints to Centrifugally (spun) cast iron pipes or Ductile iron pipes including testing of joints and the cost of rubber gasket

200 mm dia

Making connection between Tube Well & exixting distribution system of following size including all material, labour, T&P etc. complete.

80 mm dia to 150 mm dai.

200 mm dia to 300 mm dai.

Disinfecting C.I./D.I. water mains by flushing with water containing bleaching powder @ 0.5 gms per litre of water and cleaning the same with fresh water, operation to be repeated three times including getting the sample of water from the disinfected main tested in the municipal laboratory.

200 mm dia

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

200 mm dia (Class II)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

80 mm dia (Class II)

Providing and fixing Fire Hydrant (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

80 mm dia (Class II)

Supply of all materials, labour T&P etc. and construct following valve chambers with a floating coat of neat cement complete as per standard design : With F.P.S. bricks

Sluice Valve chambers

Air Valve chambers

Fire Hydrent Valve chambers

Supply, delivery and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable mechanism, magnetic drive, dry dial, hermetically sealed register, class B type, manufacutured in accordance with ISO-4064 standards or equivalent and approved by the Engineer . The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter body. The meters shall be equipped with a suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 10 Bar & temperature of 45oC. The meter shall be preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D / Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials(puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Water Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

200 mm dia PN 1.0 Bulk water Meter with Sluice valve for 200 mm pipe

Supply of all material, labour T&P etc. and provide Nala and Culvert crossing by Pipe line.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size. For Cement Concrete Pavment:

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) For Cement Concrete Pavment:

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Supplying and stacking at site 90 mm to 45 mm size stone aggregate

63 mm to 45 mm size stone aggregate

53 mm to 22.4 mm size stone aggregate

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density

Surface dressing one coat on old surface with bitumen of specified grade at the rate of 1.22 kg/ sqm of surface area with 1.10 cum of stone chippings 11.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity etc. complete :

Using bitumen emulsion (minimum 50% bitumen content- RS grade conforming to IS : 8887)

Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge.

50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge.

40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :

On bituminous surface @ 0.50 Kg I sqm

Interlinking of newly laid DI pipeline with the Reservoirs outlet pipeline by providing, laying and jointing with the required DI/CI/MS specials by flanged joints/mechanical joints including cost of specials, jointing materials cutting old pipelines, necessary reducers, enlargers, bolts, nuts, rubber insertions, labour charges etc., complete in all respect and as directed by the Engineer in charge.

For 150 mm dia DI Pipe to 200 mm dia CI/MS/DI Pipe

For 350 mm dia DI Pipe to 350 mm dia CI/MS/DI Pipe

For 350 mm dia DI Pipe to 400 mm dia CI/MS/DI Pipe

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Pump House, Boundary Wall, Gate & Site Development

EARTH WORK

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete.

CONCRETE WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

REINFORCED CEMENT CONCRETE WORK

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.c.c work Using Thermo-mechanically treated bars

Centring and shuttering including strutting,ropping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform.

BRICK WORK

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement :4 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in superstructure Cement mortar 1:6 (1 cement : 6 coarse sand)

STEEL WORK

Providing and fixing pressed steel door frames confirming to IS: 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge

Profile 'B' (Single Pattam)

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of onlysteel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 5.5 mm thick glass panes.

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.

With 12 mm mild steel U beading

FLOORING

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

ROOFING

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Coupler

110 mm bend

Shoe (Plain)

110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

FINISHING

12 mm thick cement plaster in 1:6 ( 1 cement and 6 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.

12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand)

15 mm thick cement plaster in cement mortar 1:6 on Rough face of brick wall including supply of all material , labour and T&P etc.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

20 mm cement plaster

Pointing on tile brick work with cement mortar 1:3 (1 cement :3 fine sand) Flush/ Ruled/ Struck or weathered pointing

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (New work (two or more coats) over and including priming coat with cement primer)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Fencing with angle iron post placed at required distance embedded incement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with 01/05/2012 - 1horizontal wires, of barbed wire 9.38 kg per 100 m (minimum) between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used.With G.I. barbed wire corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire 9.38 kg per 100 m (minimum) between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately):- Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire.

Supplying at site Angle iron post & strut of required size including bottom kilogram 73.30 41121 to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. Size 50×50×6mm

WATER PROOFING

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge.

Finishing the surface with 20 mm thick joint less cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

E&M work

Transportation of Rig Machine, Air compressor O.P unit camp equipages, connected T&P & necessary material required for drilling up to site of work, including loading, unloading etc. complete.

Erection and Leveling of Rig Machine at site of work

Dismantling of Rig Machine & Clearance of site after satisfactory completion of work.

Drilling of borehole from GL to 170mtr. BGL

Supply & Lowering of TW assembly as below-

300 mm dia MS ERW fincut 7.9 mm thick Plain pipe

300 mm dia MS ERW fincut 7.9 mm thick Slotted pipe

Supply and fixing of 300 mm dia, 8 mm thick tubewell cap.

300 mm dia Bail plug with nut & U- bolt as required.

Supply and fixing of 300 mm dia M.S.D.I housing clamp and girder.

Supply and shrouding of Pea gravel

Development of tubewell by 350 PSI/1100 CFM Air compressor.

Development of tubewell by the suitable capacity O.P unit.

Geohydrological survey of site.

Chemical & bacteriological testing of water sample

visual checking of Tubewell with 3600 submission by sensor system to analyse the packing of gravel, avoid presence of bentonite or any other unwanted particle/ matter along with the condition of towered assembly with complete report including rechecking after rectification of any unwanted parts upto the complete depth of tubewell & the satisfaction of proper/ Optimum finding of tubewell for maximum discharge.

Supply of Submersible pump-set of discharge 1500 lpm, 90mt head with suitable capacity motor to operate on 415±10% Volts, 3 Phase, 50 c/s A.C. supply complete

Wall/Floor mounting Starter cum panel suitable for above submersible motor.

P.W. & Earthing materials -

25 Sq mm PVC insulated Cu conductor, 3- core, XLPE submersible cable.

70 Sq mm PVC insulated, Al conductor, 3.5 - core, XLPE armoured cable.

Main Incomer MCCB-250A with MCCB enclosure box.

Double loop earthing of all electrical equipments. (as per I.E.Rules)

Main Piping & Valves

150 mm dia. CIDF Sluice valve PN-1.6 with hand wheel

150 mm dia. CIDF Reflux valve PN-1.6

MS column pipe assembly 150 mm dia 7.1 mm thick

Main Piping & specials : comprising of pressure gauge,MS bends, Tee, Ventury,DF pipes & specials etc. complete of size 150 mm dia.

Supply of tools

Supply of chain pulley block of 5 ton capacity 4.5 mt lift complete.

Supply of rubber resistance sheet of size 1 m × 2 m × 0.025 m.

Installation, testing, & commissioning of of pumping plants against guaranteed figures of Schedule 'E' at site

SITC of DG set of 80 KVA capacity

supply of 200 A TPN change over switch

Complete double loop earthing of DG set

Making foundation of DG set

Supply & Installation of chlorine dosing pump 6 kg/cm2, 8 lph, suitable to operate at single phase supply 240 +/- 10% along with Injector and NRV, Starter cum panel,Single phase automatic stabilizer, 200 Ltr.Capacity PVC tank, Chlorine testing kit, PVC pipes etc. including first fill of Sodium hypo-chloride (Naocl) solution.

Supply of Sodium hypo-chloride (Naocl) solution.

Intelligent GSM based remote terminal units/PLC with Analog & Digital Paramenter and features as specified to store and transmit data on GSM backbone.RTU/PLC designed with logic to transfer data at multiple stations and also compatible to satellite communication.

GSM Based wireless Communication system capable to transfer and gathered data from site to existing MCS including all accessories

Intelligent Energy meters

Isolation transformer (440v to step down 220v) for protection of RTU/PLC & instruments from high voltage and low voltage)

Auto phase reversal unit for auto phase corrector. (40-100 H.P.Motor)

Pressure transmitter

Electronic flow meter up to 150 mm size

Valve actuators (150 mm size)

Actuator panels.

Hard wired timer circuit for actuators

Signal/ Control cabling between RTU's and field instruments 2 pair ×1.5 PVC coated flexible screens cable.

Signal/ Control cabling for 3 ph actuators 4 c x 2.5 sq mm. cu power cable.

Signal/ Control cabling 10 c x 1.5 sq mm. cu power cable.

Conduit Pipe 1" (PVC)

Conduit Pipe 1.5" (PVC)

Accessories like AC relays,DC flexible & pipe,lugs etc.

Erection, Commissioning & Customization of i- RTU/ PLC & software & Integration with existing SCADA Station

Supply of 3-phase, rolling contact Servo Voltage Stablizer 100 KVA with input range 300 V-480 V with constant output of 415 V +/- 1% complete in all respect ONAN type.

Double loop earthing of Servo voltage stablizer. (as per I.E.Rules)

Foundation of Servo voltage stablizer as provided by the manufacturer including providing & fixing of foundation bolts & nuts etc.

Installation, testing, & commissioning of threee phase Servo voltage stablizer

Operation, running & maintenance of pumping plants for a period of 06 month in automation mode.

Internal Electrification of pump house

Wiring for light point, fan point etc. with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface PVC conduit with piano type switch, phenolic laminated sheet, suitable size GI box, with earth wire of 1.5 sq mm FR PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/submain alongwith earth wire with size of 2x2.5 sq. mm + 1x2.5 sq. mm earth wire of FR PVC insulated copper conductor single core cable in surface PVC conduit as required.

Wiring for circuit/submain alongwith earth wire with size of 2x4 sq. mm + 1x4 sq. mm earth wire of FR PVC insulated copper conductor single core cable in surface PVC conduit as required.

Supply and fixing of 5/6 amp piano type switch on the existing switch box/ cover including connections etc. as required.

Supply and fixing of 3 pin 5/6 amp socket outlet on the existing switch box/ cover including connections etc. as required.

Supply and fixing of brass batten / angle holder including connections etc. as required.

Supply and fixing of metal box of 180 rnm x 100 mm x 160 mm deep on surface with suitable size phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 amp and 15x16 amp socket outlet and 15/16 amp piano type switch, connections, painting etc as required.

Supply and fixing of metal box of 150 mm x 75 mm x 160 mm deep on surface with suitable size phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amp socket outlet and 5/6 amp piano type switch, connections, painting etc as required.

Supply and fixing of 3-pin, 5 amp ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation, testing & commissioning of pre-wired fluorescent fitting/ compact fluorescent fitting of all type complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq. mm PVC insulated copper conductor, single core cable & earthing etc. as required.

Installation, testing & commissioning ofceiling fan, including wiring the down rods of standard length, including connection with 1.5 sq. mm PVC insulated copper conductor, single core cable & earthing etc. as required.

Installation & fixing of stepped type electronic fan regulator on the mofular type plate switch including connection but excluding modular plate etc. as required.

Supply and fixing of 6 way double door S.P.N. sheet steel, MCB DB, 240 V on surface complete with copper bus bar, neutral bus bar, earth bar, inter connections including earthing etc as required. (But without MCB/RCCB/Isolator)

Supply and fixing of 5 A to 32 A, 240 V, 10 KA, C serious MCB suitable for inductive load of following pole in the existing MCB DB complete with connection, testing etc as required.

Supply and fixing of double pole, 240 V, isolator ( 40amp. ) in the existing MCB DB complete with connection, testing etc as required.

Supply and fixing of 20 W LED tubelight complete in all respect (Bajaj/Philips or Equivalent make)

Supply in fixing of LED 8 watt bulb

Supply in fixing of bulk head with 8 watt LED