REPAIR MAINTENANCE OF VALVE CHAMBER INTERCONNECTED DISTRIBUTION VALVES ALLIED WORKS OF WATER SUPPLY ELECTRIC MOTORS PUMPS AND CONNECTED WORKS SERVICES FOR SEWAGE TREATMENT PLANT TERTIARY PUMP HOUSE ETP ETC AT INA EZHIMALA

Amount

M&L for collecting the waste water/effluent sample monthly from STP before and after treatment, sample handling, transporting to NABL accredited lab approved by authorities, carry out the analysis of the following by latest IS methods complete all as specified and as directed. (i)BOD(Bio chemical Oxygen Demand) (ii)COD (Chemical Oxygen Demand) (iii)TSS(Total Suspended Solids) (iv)Total dissolved solids (TDS) (v)Turbidity (vi)PH

M&L for disconnecting the electrical connection and pipe line connection from existing position and lifting submersible sewage pumpset from sewage well / sewage sump using chain pully for repairing / winding of motor /cleaning the blockages of pump set and lowering errecting the pump set in its position reconnecting the electrical connection / pipe line and trial running for ensuring functionality complete all as specified and as directed of following capacity:- (Note:- Repair/cleaning/winding will be measured and paid separately)

M&L for dismantling of nonclog submersible sewage pump set and replacement of wornout deep groove ball bearing 2 nos, impeller, mechanical seal 2 nos, shaft protection sleeve, gaskets and O-ring and topping of lubricaton oil level. assembling the pump coupling and motor with correct alignment and testing complete all as specified and as directed of following capacity:-

M&L for dismantling 3 phase electric motor of non clog submersible sewage pump set removing burnt out winding wire from stator slots, cleaning, rewinding with super enamelled copper wire of existing gauge with proper insulation,varnishing and heating and re-assembling the same and testing complete all as specified and as directed of following capacity:-

M&L for dismantling of nonclog submersible sewage pumpset removing the blockages inside of pump and cleaning of impeller and delivery mouth / line etc and assembling the same and testing complete all as specified and as directed of following capacity :-

Supply and fixing fully automatic star delta starter (FASD) 415volts 50Hz of following capacity including taking down of old material complete all as specified and as directed.

Material and labour for scrapping existing old paint, preparation of sheet metal enclosure (LT Panel boards), sewage pipe lines of different sizes , MS walk way support bridge, hand rails etc. with one coat of primer and two coats of synthetic enamel paint complete all as specified and as directed.

M&L for repair of induction motor of 15 HP pump set, disconnection of electric cable from the terminal box of motor, decoupling the motor from the pump, remove the motor from the foundation bed and taking out the motor and transporting to authorised work shop,dismantling the motor and taking out the burnt copper winding /fibre strip/insulating materials and worn out ball bearing-2 set, clean the stator slots by CTC solution and rewind on stator slots with super enameled copper wire of existing gauge with insulating materials /fibre strip/ varnishing and made terminal connection of fibre glass coated wire. Remetalling the shaft by lathe work and welding work for correct alignment for fixing of bearing. Replacement of ball bearing -2 set. Assembling the motor and painting with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer including removal of existing paint. Replacing the burnt out gland rope, studs, nuts, bolts,washers rubber gasket,metal filling,turning/grinding and balancing the shaft etc complete all as specified and directed by Engr-in-charge.

M&L for repair of induction motor of 12.5 HP pump set, disconnection of electric cable from the terminal box of motor, decoupling the motor from the pump, remove the motor from the foundation bed and taking out the motor and transporting to authorised work shop. Dismantling the motor and taking out the burnt copper winding /fibre strip/insulating materials and worn out ball bearing-2 set. Clean the stator slots by CTC solution and rewind on stator slots with super enamelled copper wire of existing gauge with insulating materials /fibre strip/varnishing and made terminal connection of fibre glass coated wire. Remetaling the shaft by lathe work and welding work for correct alignment for fixing of bearing . Replacement of ball bearing -2 set. Assembling the motor and painting with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer including removal of existing paint, replacing the burnt out gland rope,studs,nuts, bolts, washers rubber gasket,metal filling,turning/grinding and balancing the shaft etc complete all as specified and directed by Engr-in-charge.

M&L for taking out sluice valves, refacing, regrinding including nut and bolts with washers and refixing complete all as specified and as directed of following sizes:-

(a) 300mm bore

(b) 200 mm bore

(c) 100 mm bore

(d) 80 mm bore

Material and labour for repairing of valve chamber by means of taking down existing plaster and replaster in CM 1:4 15mm thick, 2 coats of white wash and one coat of synthetic enamel painting on steel surface of size 120 x 120x 120 cm of inner dimension complete all as specified and as directed.

Material and labour for scrapping existing old paint, preparation and painting the compressor with electric motor 40 HP capacity with one coat of primer and two coats of synthetic enamel paint complete all as specified and as directed.

Supply and fixing single phase preventor 415Volts 50Hz including taking down of old material complete all as specified and as directed.

M&L for disconnecting of electrical connection and dismantling of 3 HP induction motor from secondary clarifier mechanism, removing worn out winding wire from stator slots, rewinding with super enameled copper wire of suitable gauge with proper insulation replacement of front and rear bearing, shaft protection sleeves,o rings ,gasket, mechanical seal and impeller assembling and reconnecting of electrical connection the same as existing and testing complete all as specified and as directed.

Supply and laying flat submersible 1100 Volts grade, 3 core copper conductor PVC insulated and PVC sheathed cable of 6 Sq mm including taking down old material complete all as specified and as directed.

M&L for disconnection of electric connection, decoupling the 40 HP elelctric motor of twin lob positive display rotary compressor from its position removing worn out winding wire from stator slots, rewinding with super enameled copper wire of suitable gauge with proper insulation assembling and coupling replacement of shaft protection sleeves, ball bearings, mechanical seal, the same reconnection of electrical connection and testing complete all as specified and as directed.

M&L for cleaning the raw sewage RCC sump of size 7.15mx3.5mx 5.5m once in 11 months complete all as specified and as directed. The cleaning includes :- a) Dewatering the sump with portable submersible pump. b) Removal of left over dirty water and sludge with a special sludge removal pump. c) Removal of remaining sludge from the floor with the help of industrial vacuum cleaner. d) Spraying of non-toxic, bio-degradable, eco-friendly anti-bacterial agent to disinfect the tank from all harmful pathogens.

All as per item no.17 above but sump of size 7.15mx7.15mx6m complete all as specified and as directed.

M&L for cleaning of sewage well No. 21 of size 3.5mx2.5mx10m once in 11 months of capacity 87500 ltrs complete all as specified and as directed. The cleaning includes:- a) Dewatering the well with portable submersible pump. b) Removal of left over dirty water and sludge with a special sludge removal pump. c) Removal of remaining sludge from the floor with the help of industrial vacuum cleaner. d) Spraying of Non-toxic, bio-degradable, eco-friendly anti-bacterial agent to disinfect the tank from all harmful pathogens.

Supply and fixing MCCB 250 Amps, 3pole, 415volt, 50Hz, 36 KA (fixed thermal magnetic type) complete all as specified and as directed.

Supply and fixing MCCB 200 Amps, 3pole,415volt,50Hz,36 KA (fixed thermal magnetic type) complete all as specified and as directed.

Supply and fixing MCCB 160 Amps, 3pole,415volt,50Hz,36 KA (fixed thermal magnetic type) complete all as specified and as directed.

Supply and fixing MCCB 125 Amps, 3pole, 415volt, 50Hz,16 KA (fixed thermal magnetic type) complete all as specified and as directed.

Supply and fixing MCB 40-100 Amps, C curve,TPN ,415volt, 50Hz,10 KA complete all as specified and directed.

Supply and fixing MCB 25 Amps, C curve ,TP ,415volt, 50Hz,10 KA complete all as specified and directed.

Supply and fixing MCB 16 Amps, C curve ,TPN, 415volt, 50Hz,10 KA complete all as specified and directed.

Supply and fixing MCB 40 Amps, SPN ,230volt, 50Hz,10 KA complete all as specified and directed.

Supply and fixing MCB 32 Amps, SPN ,230volt, 50Hz,10 KA complete all as specified and directed.

Supply and fixing MCB 6-32 Amps, SP,230volt, 50Hz,10 KA complete all as specified and directed.

Supply and fixing in replacement of centric butterfly valves wafer type PN1.6 as per BS-5155 &IS-13095 lever operated body grey cast iron disc-SGI epoxy coated disc seal-Nitrile/Epdm 250 &300 mm in gear operated of size 100 mm bore with all fittings confirming to IS specification complete all as specified and as directed.

Supply and fixing in replacement of 80 mm bore sluice valve with brass spindle, nuts with brass ring, flanged type of class PN 1.6 with all accessories conforming to IS specification complete all as specified and as directed.

Supply and fixing in replacement of 100 mm bore sluice valve with brass spindle, nuts with brass ring, flanged type of class PN 1.6 with all accessories conforming to IS specification complete all as specified and as directed.

M&L for removing of filth/sludge and cleaning of aeration tank of size 25mx12.5mx 4.5m depth, of capacity of water 14 Lakhs ltrs of STP either manually or using infrastructure as the case may be. The filth/sludge is expected to be around one feet thickness at bottom of the tank. Dumping of filth/sludge which was removed from aeration tank by using their own vehicle/manpower at designated place /dump yard with proper approach and in consultation with Engr-in-charge so that the vehicle carrying filth/sludge can reach easily. Note:- (a) The filth/sludge will be lifted from tank and loaded and unloaded in their own vehicle by using their own tools and machineries and will be unloaded at the designated place properly. (b) After removing of flith/sludge and cleaning of above aeration tank the same will be provided dully drained of water. (c) Rates for all equipment, manpower, vehicle and safety equipments required to complete the job is deemed to be included in the quoted rate. (d) Any damage done to the structure of piping or any equipment, contractor will be sole responsible to replace the same with identical. (e) Work will not be permitted to commence without safety gears and equipment to the workers for which Engr-in-charge will give go ahead to commence the work.

Comprehensive maintenance including repairs, replacing the spare parts and calibration to the following complete all as specified and directed by Engr-in-charge :- Multiparameter analyser(PH/COD/BOD/TSS) – 1 no Chlorine analyser – 1 no. Electromagnetic flow meter with digital display device (Outlet) – 1 no. Open channel flowmeters(Inlet) with digital display device – 2 nos. Level Radar transmitters(Grit chamber) – 2 nos. DO meters with digital display device(aeriation tank)– 2 nos. Note:- 1. Calibration to be done by authorised manufacturer only. Calibration certificate to be provided by the service engineer on the manufacturer company letter pad. 2. Repairs and replacement of all spare parts are included in the quoted rate for the entire contract period for proper functioning of the equipment. 3. Attending to faults in instruments /systems within time. 4 Sufficient quantity of sulphuric acid and DM water to be maintained for proper operation of Multi Parameter Analyser.

Repair and maintenance to filter press machine (for sludge dewatering ) of capacity 25m3/hr installed at STP - 01 nos for separating the solid sludge and water by pressing with hydraulic motors of capacity-1.5HP , shutter open/close operating motor-1HP with connected gear box,filter beds with membranes and pneumatic operated double diaprhagm sludge feed pumps with pneumatic control panel and accessories complete all as specified and as directed. Note:- 1. Repair/replacement of bearing, removal of blockages, rewinding of motors of all capacities are included. 2. Repair/replacement of spares for sludge holding shutter operating motor-1HP with connected gear box is included. 3. Reair/replacement of spares for filter beds with membranes - 24nos are included. 4. Replacement of gear box lube oil in gear box and other connected equipment - lot is included. 5.Overhauling of pneumatic operated double diapragm sludge feed pumps 3m3/hr at 60mwc-01Nos is included. 6.Repair/replacement of all spares for direct drive with butterfly valve, NRV valve and pressure gauges at outlet of each pump is included in the quoted rate for the entire contract period. 7.Repair/replacement of all contactors,MCB's,Phase sequence relay,Over load relay, CT's,Push buttons,Indicators of pneumatic operational control panel (for Sludge press machine and connected accessories) are included in the quoted rate for the entire contract period.

M&L for repair/overhauling/rewinding of stationary silenced belt driven 7.5KW air compressor with integrated refrigeration dryer including the control circuit panel(inbuild) for supplying the compressed air to the sludge sump and filter press machine and pneumatic operated double diagpragm sludge feed pumps complete all as specified and directed by Engr-in-charge.

M&L for disconnection of electric connection, decoupling the air blower motor of capacity 380 m3/hr @ 7.0mwc head electric motor of twin lob positive display rotary compressor from its position removing worn out winding wire from stator slots, rewinding with super enamelled copper wire of suitable gauge with proper insulation assembling and coupling replacement of shaft protection sleeves, ball bearings, mechanical seal, pullies,belts,belt cover inbuilt NRV, butterfly valves and pressure gauges the same reconnection of electrical connection and testing complete all as specified and directed by Engr in charge.

M&L for disconnection of electric connection, decoupling the air blower of capacity 120 m3/hr @ 7.0mwc head electric motor of twin lob positive display rotary compressor from its position removing worn out winding wire from stator slots, rewinding with super enamelled copper wire of suitable gauge with proper insulation assembling and coupling replacement of shaft protection sleeves,ball bearings,mechanical seal,pullies,belts,belt cover inbuilt NRV, butterfly valves and pressure gauges and the same reconnection of electrical connection and testing complete all as specified and directed by Engr in charge.

M&L for maintenance repair, rewinding, overhauling and replacement of defect spare parts to effluent treatment plant of 15 KLD capacity located at cadets laundry and station laundry consisting equilization tank with effluent transfer pumps-02 nos,tube settler with sludge transfer pump-02nos and centrifuge motor-01nos,dual media filter tank-01nos,activated carbon filter tank-01nos and sand filter tank-01nos with treated water pumping motors-02nos,Dosing pumps (Chlorine,lime and polyelectrolyte)-03nos, connected pipe lines and required quantity of chlorine,lime,polyelectrolyte chemical for effluent water treatment complete all as specified and as directed. Scope of Work:- (a) Cleaning of equilisation tank ,tube settler and bar screen chamber - 01nos. (b) Repair/overhauling/rewinding of effluent transfer pumps and connected accessories -02nos. (c) Repair/overhauling/rewinding of sludge transfer pumps and connected accessories -02 nos. (d) Repair/overhauling/rewinding of pressure filter pumps and connected accessories - 02nos. (e) Repair/overhauling/rewinding of sludge centrifuge motor and connected accessories. (f) Replacement of media in Dual media filter (DMF)-01nos capacity 15KLD. (g) Replacement of Activated carbon,bubbles,pebbles in Activated carbon filter tank (ACF) -01nos capacity 15KLD.

(h) Replacement with coarse fine sand,pebbles,gravels,bubbles in sand filter tank -01nos capacity 15KLD. (i) Repair/overhauling/rewinding of air blower including belt,belt cover, pump, pressure gauges and connected accessories. (J) Repair/replacement of flow meter installed at ETP for inlet flow -01nos. (k) Repair / replacement of dosing pumps for (polyelectrolyte, lime,chlorine) -03nos. (l) Supply of chlorine solution, lime and polyelectrolyte of required qty - LS. (m) Repair/repacement of multi port valve - 03nos. (n) Repair/replacement of control panel consisting of MCB's of different capacity (incoming & outgoing), relays and contactors. (o) The above scope of work is for the entire contract period. (p) one person should be available full time to attend the defects within time.

Supply only calcium hydrochloride based granular disinfectant for water treatment complete all as specified and as directed.

M&L for repair/rewinding of electric motor 30 HP Make: Grundfos , Type: CR45-4 B-F-A-E-HQQE (a) Disconnecting the electrical cable from the terminal box of motor and decoupling the motor from the pump, remove the motor from foundation bed and lifting the motor using chain pulley block and transporting to authorised work shop. (b) Dismantling the motor and taking out the burnt copper winding /fibre strip/ insulating materials. (c) Clean the stator slots by CTC solution and rewind on stator slots with duel coat super enamelled copper wire of existing gauge with insulating materials/fibre strip/ varnishing and made terminal connection using existing gauge fibre glass coated wire. (d) Assembling the motor as directed by the engr-in-charge. (e) Transporting the motor to the site refixing on foundation channel with new bolts and nut washer and spring washer, coupling the pump and motor with correct alignment apply grease and connecting electrical connections in motor terminal box testing complete all as directed and specified by the Engr-in-charge.

M&L for repair/replacement of DE & NDE roller bearing of 30 HP Pump set's induction motor vertically mounted. Make : Grundfos Type: CR45-4 B-F-A-E-HQQE (a)Removing the motor from foundation bed and lifting the motor using chain pully. (b)Removing the unserviceable DE Roller bearing and NDE using bearing pullar. (c)Dismantling the old bearing from rotor shaft and pressing new bearing. (d)Transporting the motor to the site refixing on fountation channel with new bolts and nuts,coupling the pump and motor with correct aligment apply grease and connecting electrical connection complete all as specified and as directed.

M&L for decoupling the pump & motor and transport the pump to workshop, dismantle the split case centrifugal pump to replace the unserviceable bearing 2 set, gland set replacement work of double suction brass impeller and lathe work on new stainless steel shaft along with replacement brass collar ring,gland sealing stainless steel sleeve for each side of pump shaft,coupling set, gland flange etc. assembling the pump coupling the pump and motor with correct alignment and testing complete for the 30HP pumpset complete all as specified and directed by the Engineer-in charge.Make : Grundfos , Type: CR45-4 B-F-A-E-HQQE.

Supply and fix in transformer input voltage: 415v AC output voltage: 230V AC, 500VA Capacity,50Hz 3 phase complete all as specified and directed.

Supply and fix in Star-Delta timer 3 -120 sec for 240 / 360 / 415V, 50Hz panels complete all as specified and directed by the Engr-in-Charge.

Supply and fix in repair/replacement of push button with LED Indicator – 240V A.C, Colour : Red / Yellow / Green complete all as specified and directed.

Supply and fix MN2 type relay range from 2-40 amps complete all as specified and directed.

Supply and fix MNX 9 contactor AC3 rating 9 amps AC1 rating 25amps with 1NO + 1NC auxillary contacts confirming to IS specifications complete all as specified and directed.

Supply and fix MNX 18 contactor AC3 rating 18 amps AC1 rating 30amps with 1NO + 1NC auxillary contacts confirming to IS specifications complete all as specified and directed.

Supply and fix MNX 40 contactor AC3 rating 40 amps AC1 rating 55amps with 1NO + 1NC auxillary contacts confirming to IS specifications complete all as specified and directed.

Supply and fix MNX 50 contactor AC3 rating 50 amps AC1 rating 85amps with 1NO + 1NC Auxillary contacts confirming to IS specifications complete all as specified and directed.

Supply and fix MNX 80 contactor AC3 rating 80 amps AC1 rating 100amps with 1NO + 1NC auxillary contacts confirming to IS specifications complete all as specified and directed.

Supply and fix MNX 95 Contactor AC3 rating 95 amps AC1 rating 160amps with 2NO + 2NC Auxillary contacts confirming to IS specifications complete all as specified and directed.

M&L for excavation in trenches, n exc 1.5m wide and n.exc 1.5m in depth and getting out in soft/loose soil for laying/taking out of pipe lines etc complete all as specified and directed by Engr-in-charge. Notes:- a) For all items involving excavation work contractor has to obtain prior approval from station HQ to avoid loss of other co existing utility services, in case of damage to any property he would be liable for its rectification. b)The excavation has to be done manually only.

Returning, filling in including spreading levelling watering and well ramming in layers not exc 25 cm thick in excavated soil complete all as specified and directed by Engr-in-charge.

Removing excavated soil n exc 50m and depositing where directed at level n exc 1.5m above the starting point complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engr-in-charge.

M&L for cement concrete in sub floors,sub-bases,floors and pavings of cement concrete type B2, 1:2:4 (40mm graded agreggate) of 150 mm thickness complete all as specified and directed by Engr-in-charge.

M&L for cutting existing CI pipe 80mm bore in position for insertions of CI specials complete all as specified and directed by Engr-in-charge. Note : CI special and jointing shall be measured and paid separately.

Taking out the unserviceable CI pipe 80mm bore including fittings from the trenches complete all as specified and directed by Engr-in-charge. Notes:- (i) Excavation and earth work shall be measured and paid separately under relevant items of BOQ. (ii) Recovery will be made at the rates indicated under schedule of credit for unserviceable CI pipes. (iii) Unserviceable pipes shall be removed from site of work after deducting amount towards sch of credit.

Supply and laying CI pipes 80mm bore spigot and socket ends centrifugally cast class B in any length laid in trenches complete all as specified and directed by Engr-in-charge. Note:- Fittings shall be measured and paid separately.

M&L for concrete bed to pipes in CC 1:3:6 type C2 including packing under and haunching against the sides of pipes after they are laid and tested of 100mm bore complete all as specified and directed by Engr-in-charge.

S&F CI specials such as bends (any type,radius,and angle) tapers any type (straight,bend, or double sockets etc) tee pieces,single branch 'Y' junction,double branch cross,collars caps and plugs etc of dia up to 150mm bore complete all as specified and directed by Engr-in-charge.

Material and labour tyton joints with rubber gasket for CI spigot and socket pipes and fitting of 80mm bore complete all as specified and directed by Engr-in-charge.

Supply and fix sluice valve, flanged end of class PN 1.6 with stainless steel spindle with all accessories suitable for size 80mm bore, confirming to IS specification including taking out the unserviceable one complete all as specified and directed by Engr-in-charge.

M&L for repair to valve chamber by means of scrapping the existing plaster (internal and external) completely and replaster in CM 1:4, 15mm thick, 3 coat of white wash, welding of MS hinges and including one coat of synthetic enamel painting on MS sheet after preparation of the surface of size 90x90x90 cm (inside dimension) complete all as specified and directed by Engr-in-charge.

M&L for construction of valve chamber of internal size 900mmx 900mmx900mm with foundation PCC 1:4:8 type D2 (100mm thick), laterite stone masonary 200 mm thick in CM 1:4, PCC 1:2:4 type B1 for coping (75 mm thick) , rendering in cm 1:4 ,15 mm thick on both internal and external surfaces (15cm below GL) including provision of MS sheet cover 3 mm thick and 40x6 mm flat frame, 50x6 mm hold fast embedded in coping with two coats of synthetic enamel paint over a coat of red oxide primer with necessary 3 coats white wash to external surface, earth work and excavation , handle of 12mm dia MS rod etc complete all as specified and directed by Engr-in-charge.

Supply and fix acrylic sign board of size 1.0 m x 0.75m along with necessary supports for concrete foundation and steel poles of 50mm dia for fixing in the lanes to identify the valve locations and controlling of the valves as and when necessary complete all as specified and directed by Engr-in-charge. Note:- The contractor shall print the layout of water supply with control valves on acrylic sign board in white colour with blue back ground.

M/S V ASSOCIATES

SANDR