Proposed Vegetable Market for AMC Plot at TP-43 A Sola FP-216 nr. Guli Talav, Gota Ahmedabad.

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful

4 materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil Cumt 91 128.52

Boring holes 3.5 m deep in ordinary soil (for cast insitu piles) and getting out the soil and disposal ofthe

surplus excavated soil as directed within a leadof 50 Meter for following diameter of pipes.(iii)300 mm

Providing and installing cast in situ single under reamed piles of specified diameter

and length below pile cap, excluding the cost of Concrete, steel reinforcement but including

6 the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap RMT 47 705.03

etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(C) Hard Murrum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto 50 Meter lead.(C) Hard Murrum

Filling in plinth with sand under floors including watering ramming, consolidating and dressing

Filling foundation and plinth with murrum or selected soil in layer of 20 cm in thickness including

ramming watering and consolidating etc. complete

Earthwork in cuting in all sorts of soil and soft murrum including conveying and spreading the stuff,

13 embankment as and where directed within 200meters from the end of the cutting with all required lead Cumt 175 126.48

Filling available excavated Earth (Excluding Rock ) in trench plinth side of foundation . in layer not

excluding 20 cm in depth consolidation each deposited layer by ramming and watering etc. complete

Conveyance charges lime murrum building rubbish earth manure or sludge & execavated rock and

rubbish up to 5km

Conveyance charges lime murrum building rubbish earth manure or sludge & execavated rock and

rubbish up to 5km to 6km

Conveyance charges lime murrum building rubbish earth manure or sludge & execavated rock and

rubbish up to 7 km To 8 km

Carring out plinth treatment to post construction / existing structure by spraying chemical solution for

termite control treatment including labour and material consistment with I.S.I specification. Using

Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is

recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one

litre chemical emulsion appication at the rate of 5 Litre chemical / Sqm of surface is recommended as

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates

mm nominal size) and curing complete including cost of formwork in (A) Foundation and Plinth

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of

20 formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns Cumt 120 4238.04

and Mass concrete.

Providing and laying controlled cement concrete M.200 and curing complete excluding the cost of

21 formwork and reinforcement for reinforced concrete work in © Slabs,landing,shelves,Balconies Lintels, Cumt 77 4460.36

Beams, Girders and Cantilever upto floor two level.

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of

22 formwork and reinforcement for reinforced concrete work in © Slabs,landing,shelves,Balconies, Lintels, Cumt 200 4496.07

Beams, Girders and Cantilever upto floor two level. : Ground Floor

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of

23 formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, upto Cumt 24 4593.91

floor two level. : Ground Floor

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of

formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, upto

floor two level. : First Floor

Providing TMT Bar FE 550D reinforcement for R.C.C.

25 work including bending, binding and placing in Kg 41000 75.46

position complete upto floor two level

Providing formwork of ordinary timber planking so as to give a rough finish including centering

shuttering strutting and propping etc. Height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain

concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete.

Providing formwork of ordinary timber planking so as to give a rough finish including centering

shuttering strutting and propping etc. height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain

concrete work in. (I) Edges of slabs and Breaks in floors and walls.

Providing formwork of ordinary timber planking soas to give a rough finish including centering shutter

ing strutting and propping etc. height of propping and centering below supporting floor to ceiling not

exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (G)

Columns PillarsPosts and struts. (1) Square Rectangular Polygonal in plan.

Providing formwork of ordinary timber planking so as to give a rough finish including centering

shuttering strutting and propping etc. height of propping and centering below supporting floor to

29 ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain Sqmt 680 259.88

concrete work in. (H) (2) Sides and soffits of Beams Beam Haunchings canti-levers Girders Bressumers

and Lintels exceeding 1M.in Depth.

Providing formwork of ordinary timber planking so as to give a rough finish including centering

shuttering strutting and propping etc. Height of propping and centering below supporting floor to

30 ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain Sqmt 141 252.00

concrete work in. (B) Flat surfaces such as soffits of supspened floors slabs Landings and the like. (1)

Floors etc. upto 200 mm in thickness.

Brick work using common burnt clay building bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(B) Conventional

Brick work using common burnt clay building bricks having crushing strength not less than

32 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(B) Conventional Cumt 146 4283.91

Brick work using common burnt clay building bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(B) Conventional

(i) Half brick masonry in common brunt clay building bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls

35 for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1- Sqmt 561 155.61

cement :4-sand) : Ground Floor

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls

36 for interior plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1- Sqmt 0 178.77

cement :4-sand) : First Floor

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto

floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1- cement :4-sand) : Ground Floor

20 mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of

38 12 mm thick backing coat of C.M.1:3 (1-cement:3-sand) and 8mm thick finishing coat of C.M.1:1(1- Sqmt 550 297.68

cement:1-sand) etc. complete.

Providing and applying approved coloured chips 20mm thick STONE CREAT PLASTER for exterior /

interior side on wall up to full height from ground level consisting of 12mm thick backing coat of CM 1:3

(1 cement : 3 Bodeli sand) and 8mm thick finishing coat of CM 1:1 (1 cement (Grey / White / Colour :

stone grit (approved coloured chips)) including providing & fixing 300mm wide strip of chicken net at

vertical and horizontal joints of RCC and masonary including 10mm alluminium channel for expantion

joint / grooves, curing, necessary scaffolding in true line and level etc. complete as directed by EIC.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for light shade

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in flooring treads of steps and landing

41 laid on a bed of 12mm thick cement mortar 1:3 (1- cement : 3-coarse sand ) finishing with flush pointing Sqmt 0 1062.50

in white cement.

Providing and laying 18 mm thick polished granite stone machine cut in single piece (Max. available) in

sill and jambs of door ,window,ventilation & lift wall cladding,staircase flooring landing, risers & treads,

skirting laid over 10 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) and jointed with grey

cement slurry with matching pigment incl. rubbing and polishing,half rounding edge and incl. fixing of

hilty fastener at every 1/3 span of sill as required size etc. complete colour and shed as approved by

architect engineer in charge.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar

1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with

grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc.

complete. (A) 25mm thick

Structural steel work (ConfirmingtoIS4923-1997) riveted, bolted or welded in built up for all type

44 sections,in framed work,including cutting,hoisting,fixing in position and applying apriming coat of Kg 30206 126.68

approved steel primer all complete as per the structural designs and directions of Engineer incharge.

Providing and fixing of Self Supported Roofing systems with proper overlapping and seaming b/w

different sheets without making holes or preventing the overturning the roof by wind addition made up

from superior quality, structural grade steel. Base metal width 912 mm, Steel Grade : Grade D and

Thickness from 0.80 mm,1.10 mm,1.20 mm,1.30 mm,1.40 mm, 1.50 mm BMT, 0.85 mm APT with

tolerance of +/- 0.04 mm, Regular Modified Polyster Imported Color Coated Galvalume Steel having

Profiled width of 625 mm +/-10mm. Design, supply, & fabrication of self supported single span arch

45 roof fabricated from mechanically seamed manufactured by American Hydraulic Machines to profiles of

Imported Galvalume Cold Rolled Structural Steel coils as per standard ASTM A792, Steel Sheet,

Aluminum-Zinc Alloy Coated by Hot-Dip Process,Alloy Coating AZ-150(Aluminium-55%, Zinc-43.5% &

Silicon 1.5%), Yield strength: 350 MPa, Paint coating: Regular modified polyester, Top coat of painting:

micron minimum (colour 20 micron and primer 5 micron).Bottom coat of painting: 12 micron minimum

(colour 7 micron and primer 5 micron) using make of ThyssenKrupps, Germany/Dongbu Steel Co.

Limited, Korea/ Corus Steels, U.K./ Union steel(Dongkuk) Korea/ Yjeh phuf Enterprises Ltd. Taiwan

1.30 mm thickness Sqmt 714.065 3851.00

1.10 mm thickness Sqmt 150 3310.00

1.20 mm thickness Sqmt 150 3459.00

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and

46 applying a priming coat of red lead paint. (D) In trussses and trussed purlins, upto 25 M. span and 15 M. Qnt 171.3756 9878.40

ovarall height.

Providing and fixing single or double flush door both sides laminated and I.T.W. beading all around by

using I.T.W. frame 120 m.m. x 80m.m.. shutter fabricated from 35 mm thick solid core malemine faced

three layered pre laminated flat pressed wood based exterior grade bonded BWP/BWR synthetic resin

47 having stamped IS 12823 grade I type II including three coats of lacquer polishing to exposed wooden Sqmt 0 3847.39

surfaces and Stainless steel decorative type designs fixtures / fastening etc.including I.T.W. triangular

batten patti of size 30m.m.x30m.m.etc. as per architectural detailed drawing and as directed by engineer

LABOUR FOR LAYING concrete trimix using P21 (water reducing concrete admixture at 100 ml per bag of

cement & recon 3 s fiber at 125 gm per bag of cement including carrying out vaccum dewatering and

power floater treatment in floors well compacted mechanically vibrated finish to require levels making

C channel 75 x 75 mm required to maintain level slope and thickness of the concrete road leveling of

placed concrete with surface vibrator and finishing with power floater & trowel light brooming the

surface & including cutting & filling of expansion joint as directed by Engineer in charge

Pre cast concrete kerb Providing and fixing M25 Grade of concrete precast exposed / Fair finish / texture

finish kerb stones of approved make as per approved sample of any size and any type. Kerbs shall be

fixed on the foundation prepared as per approved design. The rate shall also include for erecting and

fixing the pieces in position for complete kerb system with chamfered type of kerbs including necessary

49 accessories of kerb like radius kerbs, angles and quadrant kerbs, droplet kerbs etc. complete as per Rmt 206 912.50

drawing. Kerb shall be fixed as paper joint without any jointing material. However cement mortar shall

be provided at the backside of kerb stone joint. (Sample must be approved) Cost of excavation, cutting

base , side filling shall includes as directed engineer - incharge in above item description as per BOQ (b)

380 x 600 x 150 mm high Footpath kerb. As per approved rate

Paver Block Providing and laying shot blasted Non - interlocking, Paver blocks of specified thickness,

size, grade of concrete and colour machine made and blasting by automatic shot blasting machine and

high density of as per approved sample of approved make for footpath, parking areas, service lanes,cross

over and other areas as mentioned in the drawing. Including providing and laying 50 mm thick averave

bedding layer of coarse sand below paver block as per required grading and specification. Laid paver

block shall be mechanically compacted. The work of the paving blocks shall be executed in line and level

by skilled mason of flooring work only. Small size of paver block with same specification shall be used at

residue or at end. It should be laid in such a way that the no cutting of the paver block to be necessary. If

cutting of paver block shall be required , than cut by machine only and laying to be done by skilled

flooring mason. The finished surface of the paver block shall have coarse sand Texture Finish. Pave

blocks shall be compacted and shall be re-laid if necessary. Actual laid area shall be measured and paid

without any wastage.

Providing, laying, spreading and compacting Wet Mix Macadam (as per table 400 - 10 and 400 - 11) of

well graded stone aggregate to specification including premixing the Material with water at OMC in

mechanical mix plant as per approved design mix, carriage of mixed material by Tipper to site, laying in

51 uniform layers with motor grade/Front end Loader/paver finisher, in sub base/base course on a well Cumt 85 1526.79

prepared under base and compacting with vibratory roller to achieve the desired density including

lighting, guarding, barricating and maintenance of diversion etc. (MoRTH specification : Clause 406) by

mechanical means

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall

52 surface to give an even shade including thoroughly brushing the surface free from mortar dropping and Sqmt 562.31 40.19

other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required

53 shape even shade after thoroughly brushing the surface to remove all dirt,and remain sof loose Sqmt 550 113.40

powdered materials.etc complete

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on

54 undecorated wall surface to give an even shade including throughly brushing the surface free from Sqmt 560 78.44

mortar droppings and other foreign matter and sand papered smooth.

Providing and fixing extruded aluminum Three / Two track window having extruded aluminum Colour

Powder Coated section frame main outer size 127mm x 38.10mm x 1.35mm ,@ Wt.1.384

Kg/mt,horizontal Four track member size 122.20mm x 31.75mm x 1.10mm @ Wt. 1.205 Kg/mt,vertical

member of size 122.20mm x 31.75mm x 1.50mm ,@ Wt. 1.398 Kg/mt with sliding shutters of horizontal

member size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt,vertical member of size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt,@ with 5 mm thick transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as

per details etc complete for window.

Providing and laying waterproofing treatment for terrace including applying neat cement slurry

kg/sq.mt. of cement admix with waterproofing compound after cleaning the surface. (b) laying cement

concrete using brick bats 25 to 100 mm size with 50% cement mortar 1:5 (1-cement : 5-coarse sand)

admixed with waterproofing compound over 20 mm thick layer of C.M.1:5 to require slope including

rounding of junction or walls and slabs (c) after two days of proper curing applying a second coat of

cement slurry. (d) finishing the surface with 20 mm thick cement mortar 1:4 and finally finishing the

surface with trowel As directed with cement slurry. (e) after finishing the whole terrace shall be flooded

with water for a period of two weeks.

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme

out upto surface using white cement including rounding off junctions and extending them upto 15 cm

along the wall,clearing with water and oxalic acid etc. as directed.

Providing, Fabricating & Fixing signage's using 304 grade Stainless steel 1.5 mm thick brushed steel

finish plate (2 nos) with 8mm thk. Acrylic sheet covered with vinyl of approved colour, sandwiched

between two S.S plate and fixed with s.s struds . Sandwiched plates should be fixed in 12mm X 12mm

58 S.S 1.5mm thk.304 grade frame and punched (laser cut) lettering carried out on both the s.s plates of Sqinch 800 69.00

required size and text as directed by Engineer and hanged to ceiling with the help of S.S 8mm thick

chain at both ends with making all the fixing arrangement to the ceiling and to the plate etc. complete

all As per drawings and design supplied by architect and instruction given by authority and E.I.C.

Providing and laying of Hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass

beads and 250 gms per Sq.m. area thickness of 2.5 mm is exclusive of surface applied glass beads as per

IRC-35 2015. The finished surface to be level/uniform and free from streaks and holes or chipping of

Thermoplastic if any and including primer coat for C.C. surface and A.C.C. surface, in white and/or

59 yellow colour. Rate includes brushing, blooming and cleaning and application of paint. Zebra Sqmt 100 552.00

patta/Bump patta/Lane line/Center line/Cut patta, Directional Arrow, Lettering MoRT&H Clauses

&Volume II Part III and IRC 35-2015.Rate shall include brushing, brooming, painting and repainting of

worn out paint after a period of 2.5 years.

Note:-As per drawings and design supplied by architect and instruction given by authority and E.I.C..

Providing, Fixing, Installation of - Self Supported Galvalume Cladding sheet from with proper

overlapping and seaming between different sheets without making holes or preventing the overturning

the roof by wind addition made up from superior quality, structural grade steel. Base metal thickness

(BMT): 0.80 mm (tolerance as ± 0.04mm) metal width 610 mm with tolerance of +/- 4 mm, Steel Grade :

Grade D Regular Modified Polyster Color Coated Galvalume Steel having Profiled width of 305 mm +/-

10 mm. Design, supply, & fabrication of Verticale cladding sheet mechanically seamed manufactured by

American Hydraulic Machines to profiles of Galvalume Cold Rolled Structural Steel coils as per standard

ASTM A792, Steel Sheet, Aluminum-Zinc Alloy Coated by Hot-Dip Process. The work should be carried

out by specilialize and approved agency only. The rate of item is including fitting as per standerd

specification. The vendor shall give windload calculation before start of the work and the vendor shall be

entirely responsible for the damage of the same during transport, installation and even after installation

Constructing 15ft Dia. and 30 ft depth water harvesting as per geologoical condition, including

Excavation for harvesting upto 30ft depth including sorting out and stacking useful materials and

61 disposing off the excavated stuff upto 50 mtr lead and protect it with necessary brickwork, controlled Job 1 354138.00

cement concrete M-200, PCC, filling and as per given traditional technique design and contractor track

all necessary Equipment for safety and work complete as per given instruction by site incharge

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint,

62 brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn Sqmt 150 86.94

the surface of all dirt, dust and other foreign matter.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement concterework

using cement content as per approved Design Mix manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer,

manufactured as permix design of specified grade for reinforced cementconcrete work including

63 pumping of R.M.C. fromtransit mixer to site of laying, excluding the cost of centering shuttering Cumt 15 4853.56

finishing and reinforcementincluding cost of admixtures in recommended proportions as per IS: 9103 to

accelerate/ retard setting of concrete, improve workability without impairing strength and durability as

per direction of the Engineer - in - charge. Without Fly Ash (Mincement level as per latest IS 456 shall

bemaintained) (Cement level 450 kg

Providing and laying in position Ready Mixed M-200 grade concrete for reinforced cement conctere work

, using cement content as per approved Design Mix manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for reinforced cement concrete work including

64 pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering Cum 15 4793.10

finishing and reinforcement including cost of admixtures in recommended proportions as per IS:

to accelerate/ retard setting of concrete, improve workability without impairing strength and durability

as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained); slab

Providing and laying white glazed tiles 6mm thick in flooring treads of steps and landing laid on a bed

65 of 12mm thick cement mortar 1:3 (1-cement : 3- coarse sand ) finishing with flush pointing in white Sqm 80 908.17

Providing and laying white glazed tiles 6mm thick in

skrting risers of steps and dedo on 10mm thick

cement plaster 1:3 (1-cement : 3-coarse sand) and

jointed with white cement slurry

67 Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

68 Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

69 Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

70 Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

71 Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and floor etc. complete. [E] 40mm.

72 Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and floor etc. complete. [F] 50mm.

73 Supplying & erecting resin bonded flap rock wool / glass wool with conductivity valve 1.67 sq.mm per

watt & to with stand the temp. to 100 degree centigrade C thickness 50mm with G I pipe of following

size dia "B" class as per IS:1239. The plastic sheet to be used as covering of glass wool. Al. cladding

besides other materials like chicken mesh, 26 G Al. Sheet shall be used for cladding the insulation pipe.

(A) for 20 mm dia pipe Mtr 30 360.00

(B) For 25 mm dia pipe Mtr 20 440.00

(C) for 32 mm dia pipe Mtr 20 530.00

(D) for 40 mm dia pipe Mtr 45 620.00

(E) for 50 mm dia pipe Mtr 5 760.00

74 Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 20mm dia. Each 4 276.00

75 Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 25mm dia. Each 4 457.00

76 Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia. Each 3 584.00

77 Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 50mm dia. Each 4 821.00

78 Providing and supplying C.I. Air valves of approved make & quality of following class and diameter

including taxes, insurance, transportation, freight charges, octroi, inspection charges, loading,

unloading, conveyance to departmental stores, stacking etc. complete. Air Valves single (S2) Type

79 Providing and fixing mosquito proof stainless steel overflow grating for tanks.(//

Audco/Lehry/ R.B./ Spirex) 100mm dia.

80 Consruction of Valves chambers in brick or bela stone masonry, locally available in C.M. 1:6 foundation

concrete 150mm thick in CC 1:4:8 of trap metal size 25mm to 40mm thick, inside cement plaster in CM

1:3 and cement pointing outside in C.M. 1:3 and top cover of precast RCC slab 100mm thick with key

hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from G.L.

to pipe invert level incl. complete civil works but excl. cost of excavation and refilling with cast in situ Each 3 5380.00

RCC slab in one single piece with fixing of CI-MH Frame and cover (excl cost of CI-MH Frame and cover)

with 23mm thick brick masonry wall in CM 1:6 (d) size of chamber 0.60 m x 0.60m and 1.0mt deep with

precast slab in two parts 15mm with single piece 10cm with fixing MH Cover.

81 Supply, installation, Testing and Commissioning of 15mm Nominal diameter Garden Hydrant with gun

metal Ball Valve, GI pipe for Flexible hose Connection Provision and Each 5 2000.00

all required accessories etc.

82 Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required capacity each

with all necessary fittings and connection etc. complete on terrace.

83 Supplying and erecting chromium plated heavy duty brass valve for inlet pipe of water heater 15 mm

84 Supplying and erecting 15mm brass non-return valve for inlet pipe of storage water heater.

85 Supplying and erecting dead pressure releasing valve for storage type water heater with necessary

86 Providing & erecting fibre reinforced PVC flexible pipe with brass locking nuts & washers & clips at both

ends complete erected without leakage

INTERNAL SWR SYSTEM

87 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and floor.(C) 32mm

88 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and floor.(D) 40mm

89 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and floor.(E) 50mm

90 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and floor.(G)110 mm

91 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the

following outside Dia. Low densidy, complete with special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and floor.(F) 75mm

92 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the

following nominal diameter of self cleansing design with C.I scread down or hinged grating including each 7 565.43

the cost of cutting and making good the walls.

93 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 75 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of each 4 552.83

cutting and making good the walls.

EXTERNAL SWR SYSTEM

94 Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover

with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm Each 3 1279.40

x 100mm size P type. (upto 10 ton)

95 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 100 208.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

96 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 100 373.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

97 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 100 738.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

98 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 100 1004.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

99 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats

40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand)

finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including

curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size Each 2 10920.76

560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength

not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth

0.90 Metre for 150mm diameter sewer.

100 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats

40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand)

finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including

curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size Each 2 19139.07

560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength

not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth

1.50 Metre for 150mm diameter sewer.

101 Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate

40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary

formwork and curing complete.(B) 150mm dia. (166mm Ave. bed thickness)

102 Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks

having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm

x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover

23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i)

Inside dimensions 455mmx 610mm and 450mm deep for single pipe line. (upto 10 ton)

103 Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length. Each 100 100.90

104 Constructing Brick masonry road gully chamber 500mm x 450mm x 600mm including 500mm x 450mm

C.I. horizontal grating wih frame complete.(upto 10 ton)

105 Constructing brick masonry road gully chamber 1100mm x 775mm including 500mm x 450mm (C.I.

horizontal grating with frame and vertical grating complete.) (upto 10 ton)

106 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 50 208.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

107 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 80 373.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

108 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 75 738.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

109 Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline

coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth

internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per

EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection Rmt 60 1004.00

charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID

110 Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate

40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary

formwork and curing complete.(B) 150mm dia. (166mm Ave. bed thickness)

TOILET FIXTURES

Providing and fixing wash down water closet (European type, W.C. Pan) with integral P or S trap

111 including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover Each 2 1290.80

to be measured and paid for separately) (A) vitreous China Pattern :(i) in white colour

Providing and fixing 12.5 Litres low level flushing cistern with a pair, of C.I. or Mild brackets,

complete with fittings such as lead valve less syphon, 15mm nom.nal size brass ball valve with

polythene float, C.P brass handle unions and couplings for connections, with inlet, outlet and overflow

pipes, 40mm dia. porcelain enamelled flush bend including cutting holes in walls and making good the

same connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for

separately)(A) Vitreous China (I) In white colour

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and

rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white

114 including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back Each 3 1400.18

washbasin 550 mm x v 400mm size. (i) In white colour.

115 Providing and fixing C.P. brass waste for washbasin or sink. (B) 40mm dia. Each 3 88.94

116 Providing and fixing M.I. fisher union for washbasin or sink. (B) 40mm dia. Each 3 87.77

117 Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni trap. Each 3 36.61

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick

A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed

to wooden plug with C.P. brass screws.

120 Providing and fixing toilet paper holder.(A) C.P. Brass Each 3 414.53

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down

Bib Tap. (i) 15mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back

nuts. (i) 15mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in

pipe line etc. complete.(i) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in

pipe line etc. complete.(ii) 25mm dia.

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap etc.

complete.(A) White earthenware flat back or corner type size 430mm x 260mm x 350mm.

126 Providing and fixing Rubber plug for sink or wash basin. Each 3 16.98

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for

128 Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (ii) 50mm dia. Each 3 187.96

Providing and fixing Angle Cock with screw, back nuts all necessary fittings etc. Completed

(Cera-CM108/ Parryware-T9939A1 / Hindware-F100043)

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed

130 concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China. (1) Long Each 3 926.10

pattern = White colour

Providing and fixing 12mm dia. Health faucet with 8 mm dia of JAQUAR / HINDWARE/ CERA or

131 approved make selected by Architect with flexible pipe of 1mt. length and holding stands complete. Each 2 1200.00

Model Equivalant to Jaquar- CAT - ALD-577.

Supplying & erecting approved make self-priming domestic monoblock water pump with 1.5 H.P

132 motor, suitable for operation on 230 volts, 50c/s. AC supply with metallic flange, and M.S. Ea. 2 9222.00

impeller delivery and following discharge 44 LPM at 32 Mtr head suitable 25 mm dia delivery

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper

cable approved make of following Size. (C) 3 Core x 4 Sq. mm

Supplying & erecting ISI Marked (Embossed) following size of “C” Class G.I . Pipe & erecting as

directed by Engineer-in-charge with necessary plumbing as desired. (C) 40 mm dia

Supplying and erecting with leak proof materials, M.S. Heavy duty ISI marked coupling having

135 threads of 8 TPI/11 TPI suitable for ‘C’ class pipe to take load of pump and pipe assembly of Ea. 4 71.00

following size andTPI :- (A) 40mm( 1.5") dia. pipe 8 TPI

Supplying & erecting G.l. bend for pipe connections suitable for (C) 40 mm (1.5") Ea. 2 94.00

136 Supplying & erecting ISI Marked G.l. Elbow for pipe connections suitable for (C) 40 mm (1.5") Ea. 2 89.00

Supplying and erecting Direct On-line Electronics Starter with 2-5/4-10/8-14/10-16 Amp. Rating

relay (variable current setting) directly operated in totally insulated elegant enclosure and

Amp. Rating power relay with start - stop button for single phase operation up to 3 HP as per

complete erected on P.W. Block with following features.

Low voltage cut off below 140 V

High voltage cut off above 280 V

Overload protection

Indicating LEDs for motor on lv, hv & overload tripping. [Cat.II]

Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as

138 per instruction of Engineer in charge on site complete with wiring connection with existing wires Ea. 1 2332.00

, with copper conductor from pump to upper and lower tank.

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to

be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell

139 push & accessories and earth continuity of following type, erected on PVC / Metallic box, single Pt 100 415

mounting base frame covered with textured/metallic front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories CAT III

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and

140 necessary connection with primary light with accessories erected on Metal / PVC box covered Pt 20 121

with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked

1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be

erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum

free EME four or more step type electronic fan regulator with separately mounted and

accessories with earth continuity of following type erected on PVC / Metallic box, single mounting

base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (a) with medium class

Rigid PVC pipe and accessories.CAT III

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of accessories. For 6A Plug with 2-1.5 sq.mm Cu.

Wire with medium class Rigid PVC pipe and accessories CAT III

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected

concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of accessories.[III] For 16A Plug with 2-2.5 sq.mm

Cu. Wire (a) with medium class Rigid PVC pipe and accessories.CAT-III

Providing & erecting Switch board for Computer or electric apparatus consisting of following

items in single board erected on PVC / Metal board with 3 mm thick PC (Polycarbonate) /

Acrylic sheet erected as directed for [B] modular type accessories

1 no. 6A/16A universal plug-switch combined. CATIII

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

144 erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in approved manner as directed

MAINS WIRING AND CONDUIT

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of

following size (a) with medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of

following size (a) with medium class Rigid PVC pipe and accessories (B) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS

147 PVC insulated stranded wire of green colour for earth continuity of following size. (a) with Mtr 800 106

medium class Rigid PVC pipe and accessories

(A) 2 wire 4 sq. mm

FANS & EXHAUST FAN ACCESSORIES

Supplying and erecting approved make double ball bearing oscillating type Heavy duty bracket

148 fan with Aluminium Blades A.C. 23OV. 50cy/s wall mounted with height adjustment and rotary

tilting device complete with guard, wall bracket,mounting accessories as directed.

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing

ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with

aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be

approved by Engineer in charge))

150 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. Nos 2 18

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly

painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to

152 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete Nos 2 107

erected concealed in Ceiling with necessary finishing.

Supplying & erecting approved make low noise decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame. 200mm with 1350RPM Cat.II

LIGHTING FIXTURES :

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

154 Luminaire efficacy> 85 lumens/watt ,LED EA 2 370

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between

the ranges shown.). (A) Tube Light with integral driver. (iv) 22-24 Watts, Surge - 2KV,IP-20,

conventional 4 feet. Cat-lll

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage,

minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser,

mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5. (A) LED Lamps integral type, with

PC diffuser suitable LAMP holder. (iii) 10 to 15 watts. Cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between

the ranges shown.). (A) Square/ Circular shaped Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips complete.IP20. (iii) 16-20 watts, Surge-2 KV. Cat-lll

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage

of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD <

157 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED EA 2 6028

driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.). (B) Flood Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply with over-voltage protection. (iii) Above 60 to

90 watts. Cat-lll

DISTRIBUTION BOXES 0

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS

5486-1986 without MCB to house appropriate nos. of MCBs N) Three phase 6 way SS Double

door for horizontal single phase outgoing

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS

5486-1986 without MCB to house appropriate nos. of MCBs N) (b) sheet steel double door (v)

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

(iii)8 way Ea 1 1141

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type

(iii)8 way Ea. 1 3379

(iv)12 way Ea. 1 3836

Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush /

surface mounted double door (IP54) fitted with insulated copper busbar, isolated neutral link, earth

161 bar and DIN rail, confirming to IS 13032 and BS 5486-1986,IP-54 suitable for 63/100 AMP TPN MCCB +

RCCB as incomer and three phase outgoing as per following .(The DBs should be used of same

company of MCB to be used)

(B)6 way outgoing Ea 1 12061

(D)12 way outgoing Ea 1 18480

MINIATURE CIRCUIT BREAKER

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on

162 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to EA 110 111

IS 8828/1996 with ISI Mark Cat.III

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA

163 breaking capacity & confirms to IS : 8828 in existing box having following capacity (B) 40 Amp. Ea 4 293

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve)

164 having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity Ea 4 297

(A) 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve)

165 having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity Ea 4 327

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

166 breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Ea 4 590

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

167 breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Ea 2 662

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA

168 breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Ea 2 632

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

169 breaking capacity & confirms to IS :8828 in existing box having following capacity Ea 4 730

C) 63 Amp. CAT-III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing box having following capacity

(c)63 Amp. Cat-III

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and

Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature & do not incorporate any

electronic component. for following Max. rating erected as directed (i) 25 Amps.DP Cat. III

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and

Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature & do not incorporate any

electronic component. for following Max. rating erected as directed (i) 40 Amps.DP Cat. III

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and

Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having

characteristic of quick action & tripping with all advance feature & do not incorporate any

electronic component. for following Max. rating erected as directed (i) 63 Amps.DP Cat. III

ELECTRICAL PANELS

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor

type cubical panel board necessary IP-42 and above protection as per approval from engineer

incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end terminal connection,danger notice

board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy

powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved manufacturers with following

Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating

proper size of M.S. angles,square,round, flats, bars, channels, sections complete with cutting,

175 welding, grinding & finishing duly painted with one coat of red oxide with erection on site as per kG 300 77

direction of engineer in charge with necessary grouting, cementing, plastering & finishing

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars

with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary bus bar supports /insulators, main

cable socket to each busbar,erected in existing cubical panel with necessary connections. (C)

Suitable for 300 Amp. Capacity

(A) Suitable for 100 Amp. Capacity Rn.Mtr 10 654

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 35 KA. and above at 415 V . having normal current rating 250A. with variable

177 thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, Ea 1 20739

spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS=100% of

ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed

178 thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections, Ea 1 6112

spreader tinned copper & complete erected in existing 16 G.M.S. housing. . ICS=100% of ICU

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having normal current rating 125A. with Fixed thermal &

179 magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader Ea 1 7976

tinned copper & complete erected in existing 16 G.M.S. housing.. . ICS=100% of ICU only

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage,

180 minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser,

mounting suitable for E14 / E27 / B22 lamp holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable LAMP holder Ea 6 111

(ii) 5 to 8 watts

181 Operational Handle Assembly Complete for

182 Cable Terminal ( ‘Plain" Type)Set of Four for

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction

(D) 4 pole 440V 40 Amp. Ea 2 2755

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on

240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display.

Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as required with necessary connection

erected as directed.

Providing and erecting Approved make Earth fault Relay suitable to mount with inter connection

suitable to following size of moulded case circuit breaker having CT ratio & MCCB rating as

following along with shunt trip 220V AC. with all internal connections & complete erected in

existing M.S.housing..

Providing & erecting Medium Voltage Danger Notice Board sticker as per language suggested by

engineer incharge of standard size as per IS-2551

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power switchgears, motor

starters & control wiring) with required size of copper lugs, nuts and bolts if required.

(b) One wire 1.50 sq. mm Mtr. 25 16

(c) One wire 2.50 sq. mm Mtr. 25 26

188 providng and erecting Suitable set of CTS for 100A Energy Meter Ea. 1 2085

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover,

complete erected with necessary connections.

190 TOGGLE SWITCH Ea. 3 115

191 THERMOSTATE HEATER Ea. 3 100

Providing and erecting multifunctional meter suitable for application of Power monitoring and

showing measurement of following Voltage, Frequency, Apparent energy, Apparent power,

Active and reactive energy, Active and reactive power, Average voltage Vavg, Peak demand power

PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3, Unbalance current, Power factor

and displacement PF (signed, four quadrant), Calculated neutral current, Active, reactive,

apparent energy (signed, four quadrant), Active power P, P1, P2, P3, Voltage U21, U32, U13, V1,

V2, V3, Phase currents, Average current Iag, Peak demand currents, Reactive power Q, Q1, Q2, Q3,

Demand current I1, I2, I3, [Us] rated supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC,

Network frequency 50 Hz, Type of network 3P, Display type 7 segments LED, Display colour Red,

Messages display capacity 3 fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height

192 Supplying rubber matting of following thickness as per IS:15652/IEC 61111

(c)12mm S.Mtr 10 3051

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be

erected as directed of following size.

(E) 3 core 2.5 Sq. mm Rmt 200 135

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor

194 for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing

or floor of following size of cable.

(B) 3 core 4 Sq. mm Rmt 150 283

(C) 3 core 6 Sq. mm Rmt 150 390

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

195 conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rmt 150 369

following size of cables. (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

196 conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rmt 100 719

following size of cables (G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core)

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Rmt 100 529

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

197 conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rmt 50 215

following size of cables (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

following size of cables.

(A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

following size of cables.

A)4 core 16 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper

200 conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at Rmt 150 503

road crossing or floor of following size of cables. (C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor

201 for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing Rmt 750 667

or floor of following size of cables. (A) 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

202 rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc EA 40 102

for following size of cables. (C) 3 & 1/2 core 70 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

203 rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc EA 30 139

for following size of cables. (E) 3 & 1/2 core 120 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

204 rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc EA 30 189

for following size of cables. (F) 3 & 1/2 core 150 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

205 rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc EA 30 75

for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm

Providing and fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

206 armoured cable complete with out going tails, insulating tape etc for following size of cables. EA 30 51

E) 2 to 4 core 25 Sq. mm

Providing and fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

207 armoured cable complete with out going tails, insulating tape etc for following size of cables. Ea 110 47

D) 2 to 4 core 16 Sq. mm

Providing and fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

208 armoured cable complete with out going tails, insulating tape etc for following size of cables. Ea 55 38

(B) 2 to 4 core 6 Sq. mm

Providing and fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

209 armoured cable complete with out going tails, insulating tape etc for following size of cables. Ea 80 38

C) 2 to 4 core 10 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

210 evenly crimped with high pressure tool & connected to switchgear terminals with Ea 100 25

brass/cadmium plated nut bolts in an approved manner. (E) 70 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

211 evenly crimped with high pressure tool & connected to switchgear terminals with Ea 60 45

brass/cadmium plated nut bolts in an approved manner. ((G) 120 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

212 evenly crimped with high pressure tool & connected to switchgear terminals with Ea 48 61

brass/cadmium plated nut bolts in an approved manner.(H) 150 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

213 evenly crimped with high pressure tool & connected to switchgear terminals with Ea 28 20

brass/cadmium plated nut bolts in an approved manner. (D) 35/50 Sq.mm.

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

Solder less crimping type Copper lugs conforming to IS suitable for cable of following size evenly

216 crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated Ea 120 8

nut bolts in an approved manner. (A) 1.5/2.5 to 6 Sq.mm

217 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. KG 50 787

218 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. KG 100 77

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/

ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer,

LT panel board, Motors etc. using copper clamp.

Supplying & erecting in earthpit of minimum bore dia. 225mm size approved make Safe Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe

221 dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with

constant ohmic value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty cover.(approved make

OEM has to submit test certificate including value of earth resistane of installation.

[B] For Electrical installation up to 11 KV located in other than normal soil i.e. Soft Rock,

Marshy Soil etc.

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg.

(c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing,

A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in

normal soil. Ea 1 10489

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel electrode with 250 micron

copper bonding & 1 bag of Carbon fill Based environment friendly backfill tested as per IEC

222 62561-7 in NABL accredited Laboratory and suitable stainless Steel double sided clamp. Eco Ea 3 5933

Friendly rust proof heavy duty weather proof Polyethylene Earth Pit Chamber with following

dimensions :254 mm dia (top), 330 mm dia (bottom) & 260 mm (height).

EXTERNAL STREET LIGHT

Street Light Pole

Supply of approved make GRP / FRP Pole having following specifications: GRP Light Pole made

by CNC filament winding machine using thermoset resin polyester/epoxy resin system) having

minimum 62% glass content. The pole should be in one piece and tapered round in shape, having

smooth finish and should be totally free from corrosion as well as non conductive & shock proof

Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly

painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV

resistance and pigmented. A highly weather resistant polyurethane coating shall be applied to the

pole after applying suitable primer system that ensures proper adhesion of the paint. Minimum

coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more than

10% of the length of pole for the given load“? Pole should be generally made as per the

dimensional data, performance criteria and some interchangeability features of poles as per

standard ANSI C 136.20 latest version or ASTM D 4923/01 . The size of pole and type of

installation are as below

Supply of approved make FRP Pole having following specifications: FRP Light Pole made by CNC

filament winding machine using thermoset resin polyester/epoxy resin system) having minimum

62% glass content. The pole should be in one piece and tapered round in shape, having smooth

finish and should be totally free from corrosion as well as non conductive & shock proof Pole

should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly

painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A

highly weather resistant polyurethane coating shall be applied to the pole after applying suitable

primer system that ensures proper adhesion of the paint. Minimum coating thickness shall be

to 100 micron. Deflection of the pole shall not exceed more than 10% of the length of pole for the

given load“ Pole should be generally made as per the dimensional data, performance criteria and

some interchangeability features of poles as per standard ANSI C 136.20 latest version or ASTM D

4923/01 including cable termination box with necessary accessories . The size of pole and type of

installation with foundation as per manufacturer details and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[H] Overall length of 6 Mtr. Average Thickness: 7.5mm

Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx. Weight of Pole 32 kg approx. (Without Ea. 15 13920

Base) Anchor Base (Size 300X300 & 18mm Th.)

(2) Suitable for base plate mounting Double arm Bracket.

[C] Overall length of 6 Mtr. Average Thickness: 8mm.

Top/ Bottom OD Dia A/F 114/174 mm ± 2mm approx. approx. Weight of Pole 38 kg approx. Ea. 5 14747

(Without Base) Anchor Base (Size 300X300 & 18mm th.)

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for

the pole of size 45 x 45 x 100 cm. Deep in below ground level with plinth of 45 cm x 45 cm (or

cm dia x 45 cm) high upper ground level with necessary curing and finishing in approved manner.

( for 4 & 6 mtr pole)

Providing cement concrete.for foundation or for concrete filling in 1:2:4 ratio with 20 to 25 mm

stone metal duly plastered with necessary curing for pole muffing or any other purpose.

Providing FRP/GRP arm bracket of having 15˚ arm with 50 mm OD pipe *5 mm thk,1000mm

long from pole centre

(A) Single arm bracket Ea. 15 1882

(B) Double arm bracket Ea. 5 2390

Supplying & erecting approved make IP 55 grade Company fabricated Timer Panel of following

capacity for switch On-Off street lights on time scheduling basis made from 16G CRCA sheet duly

epoxy power painted inside and outside with hinged doors and locking arrangement consisting of

suitable size of 4 Pole MCB and 4 pole contactor (cat-III)with analog time switch, auto manual

switch of same make and suitable input and output Bakelite terminals and with door earthing

approved by Engineer in charge.

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material

at required depth in existing trench for laying of cable. below ground / road surface for

enclosing cable

(A)50 mm outer dia Mtr. 800 62

(B)63mm outer dia Mtr. 500 73

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground across the road

228 crossing or on floor with necessary material in an approved manner and making the ground as Mtr. 200 340

per original.(C) 300 mm dia

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage

of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD <

229 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED Each 25 5917

driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.). (A) Street Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply with over-voltage protection. (iii) Above 60 to

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as directed.

(h) 2.50 Sq.mm 3 core round PVC sheathed Mtr 350 73

FOOD COMPOSITOR MACHINE CONSIDER 500 KG/HR. CAPACITY SEMI AUTOMATIC

Providing and erecting Approved make Four pole microprocessor base moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A

to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. -

(The Enclosures should be used of same company of MCCBs to be used) -ICS=100% of ICU only

LIASIONING WORK

FOR OBTAINING NOC

232 Power Liasoning Charges for obtaining N.O.C from Electrical Inspector Statutory authority for Job 1 20000

Power/Ele. Installation. Liasoning Charges shall include preparing required attested documents &

drawing for obtaining NOC/Test Report on behalf of client.