Special repair to Old Type-IV Qtrs (TBS) in Dr R.P.G.M College at Tanda in Distt Kangra(HP)

Amount

Dismantling roofing including ridges, hips, valleys, gutters etc; stacking the serviceable materials and disposal of un-serviceable materials Slate Roofing upto any lead and including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Demolition of thatch roofing including mats, bamboo, jaffari, capping to ridges, hips, etc. including stacking of serviceable materials disposal of un-serviceable materials within upto any lead and and including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Demolition of brick/stone work above G.L. upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres lead in cement mortar complete as per direction of Engineer- Incharge, including entire carriage of materials within all leads, lifts and other incidentals.

Dismantling of cement asbestos celotax/hard board in ceiling or partition wall including stacking of serviceable materials and disposal of un-serviceable materials within any lead (Frame work such as joists, beams to be measured and paid for separately) complete and including carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Dismantling tiled floors laid in mortar upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within any lead (wooden/concrete joists to be measured and paid for separately) upto any thickness of tiles complete, as directed by the Engineer-Incharge, including entire carriage of materials within all leads, lifts and other incidentals.

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three meters) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimeter)layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals.

Providing and laying concrete for plain/reinforced concrete in open foundations in 1:3:6 (One cement: three sand: Six graded broken/crushed stone aggregate 20mm(Twenty millimeters) nominal sizecomplete as per drawings and technical specifications Clause 802, 803, 1202 and 1203 PCC grade M-10 (M-ten) including entire carriage of materials as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design.

Providing from work of ordinary timber plankings so as to give a rough finish including centring,shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililng not exceeding 4 (Four) metres and removal of the same for insitu reinforced concrete and plain concrete work in Sides and Soffits of beams, beam haunchings, contiliver girders, bressumers and lintels not exceeding any depth complete and as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing from work of ordinary timber plankings so including centring,shuttering, strutting and propping etc; height of propping and centring below supporting floor to ceililng not exceeding 4 (Four) metres and removal of the same for insitu reinforced concrete and plain concrete work in Foundations,footings,bases of columns etc. and mass concrete complete and as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing from work of ordinary timber plankings so including centring,shuttering, strutting and propping etc; height of propping and centring below supporting floor to ceililng not exceeding 4 (Four) metres and removal of the same for insitu reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors,roofslanding and the like Floors etc. upto 200mm (Two hundred millimetres) in thickness complete and as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing and laying cement concrete work 1:2:4 (One Cement : Two Sand : Fopur graded stone aggregate 20mm (Twenty millimetres) nominal size) and curing complete including cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete etc; including carriage of material as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing Tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete including cost of binding wires complete as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Second class brick work using common burnt clay building bricks upto any floor level in cement mortar 1:6 (One cement: Six sand) as per approved drawing, design and as directed by the Engineer-in-Charge, including entire carriage of materials within all leads, lifts and other incidentals.

15mm (Fifteen milimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth including drip course and grooves with cement mortar 1:6 (One cement: Six sand) above plinth level to floor all levels complete including carriage of material within all leads, lifts of materials and other incidentals as per specification approved drawing, design and as directed by the Engineer-Incharge.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting ,fixing in position and applying a priming coat of red lead paint in beams joists channels, angles, tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like as directed by the Engineer-Incharge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six milimetres) diametres with prepainted limpet and rubber washers complete with all accessories as required as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing and fixing valleys 60cm (sixty centimetres) thick 0.60mm (Zero decimal Six Zero milimetres) thick prepainted shee over steel trusses prepaim\nted galvanized steel with hot dip metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with all accessories as required (Steel truss will be paid extra) as directed by the Engineer-in-Charge, including entire carriage of materials within all leads, lifts and other incidentals

Providing and fixing M.S. B.P Sheet 1.66mm to 2mm (One point sixty six to Two milimetres) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separately) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals.

Repair to plaster in patches of 2.50 sqm (Two decimal five zero) square metres upto any thickness including cutting the patches in proper shape and re-plastering the surfacing to the wall including disposal of rubbish to the dumping ground with cement mortar 1:3 (One cement : Three sand) complete, as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing and fixing anodised aluminium work for door, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/ panelling C.P. brass/stainless steel screws for doors windows and ventilatiors and glazed partitions frames. All complete as per architectural drawings and as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing anodised aluminium work for door, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/ panelling C.P. brass/stainless steel screws for shutters of doors windows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required including the cost of PVC/neoprene gaskets as required (fittings and glazing/panelling shall be paid for separately) all complete as per architectural drawings and as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing and fixing 250x10mm(Two hundred fifty into ten milimetres) nominal size aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete as per direction Engineer-In-charge including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 100 mm (One hundred milimetres) nominal sizze aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as directed by the Engineer-in-Charge, including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing 300x16mm size (Three hundred into sixteen milimetres)nominal sizeanodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. completed including entire carriage of materials within all leads, lifts and other incidentals

Providing and fixing 150x125x27x2.80mm oxidized M.S. presses parliamentary hinges with necessary screws etc complete including entire carriage of materials as per directed by the Engineer-in-charge including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 12mm (Twelve millimetres) thick prelaminated board both side bwp phenol bonded exterior/interior grade panelled shutters including bright finished/black enamelled iron butt hinges with necessary screws complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Supplying and fixing 4mm (Four millimetres) thick Plain Glass panes with putty and nails including removal of broken glass panes wherever necessary as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Boulder filling dry hand packed tightly under floor including watering, ramming, consolidating and dressing complete and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals .

Providing and laying Duro stone vetrified tiles 300x300mmx10mm (Three hundred into three hundred into ten millimeters) thick in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm (Twelve millimeters) thick cement mortar 1:3 (One cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as directed by the Engineer-Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing and laying matt finished vetrified tiles 605x605x8mm (Six hundred five into Six hundred five into eight millimeters) thick in grey/coloured or of approved shade in skirting, treads of steps and landing laid on a bed of 12mm (Twelve millimeters) thick cement mortar 1:3 (One cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.including entire carriage of materials within all leads, lifts and other incidentals

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm (Six hundred into Six hundred into ten millimetres) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (Twelve millimetres) thick cement mortar 1:3 (One cement : Three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and laying 15mm to 20mm (Fifteen millimetres to Twenty millimeters) thick granite stone in flooring 20mm (Twenty millimeters) (average) thickness base of cement mortar 1:3 (One cement : Three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 10mm (Ten millimetrers) thick plaster flat surfaces of paris (Gypsum unhydrous) ceiling upto a height of 5 (Five) metres above floor level excluding first class kail wood stripes 25mmx6mm (Twenty five into six millimetres) with 10 mm (Ten) gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be measured and paid for separatly) as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Removing dry or oil bound distemper by washing and scraping and sand papering the wall surface smooth including necessary repairs to scratches complete, as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete, as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Wall painting (one coat)with plastic emulsion paint of approved brand and manufacture on decorated wall surface to give an even shade including thoroughly brushing the surface clean of all dirt grease,loose pieces of scal and sand papered smooth including entire carriage of materials within all leads, lifts and other incidentals.

Extra over items 27 for every sub sequent coat of wall paint of approved brand and manufacture as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface as directed by the Engineer-Incharge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white as per directed by the Engineer-Incharge, including carriage of materials within all leads, lifts and other incidentals.

Painting one coat (excluding priming coat) on previously painted steel and othermetal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foreign matter with enamel paint other than white, as directed by the Engineer-Incharge, including entire carriage of materials within all leads lifts and other incidentals.

Extra over items No. 29 for every sub sequent coat of paint with white enamel paint complere as per directed by the Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals

Painting one coat(excluding priming coat)on previously painted wood and wood based surfaces with readymixed flat oil paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter and sand papering and stopping complete as directed by the Engineer-Incharge, including carriage of materials within all leads, lifts and other incidentals

Extra over items No. 31 for every sub sequent coat of paint complere as directed by the Engineer-Incharge, including carriage of materials within all leads, lifts and other incidentals

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe Cera, Jaquuar and Hindware in cement mortar 1:1 (One cement : One sand) Angle Indian Universal closet (Seat and over to be measured and paid for separately complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing sand cast iron 100mm (Hundred milimetres) size P or S traps for water closet (squatting pan) including jointing the trap with pan and soil pipe in cement mortar 1:1 (one cement: one sand) complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing plastic seat (Solid/Hollow type) and cover Cera, Jaquuar and Hindware for wash down water closet with C.P. Brass hinges and rubber buffers complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 550x400mm (Five hundred fifty into four hundred millimetres) (vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white Cera, Jaquuar and Hindware including cutting holes and making good the same but excluding fittings complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 32mm (Thirty two millimetres) dia C.P. Brass waste for wash basin or sink ISI make complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 600x450mm (Six hundred into Four hundred fifty milimetres) size bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 32mm (Thirty two milimetres) C.P. Bottle Trap for wash basin and sink complete as directed by the Engineer- Incharge, including carriage of material within all leads, lifts and other incidentals.

Providing and fixing recessed roll type toilet paper holder complete as directed by the Engineer- Incharge, including carriage of material within all leads, lifts and other incidentals.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws Cera, Jaquuar and Hindware complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 15mm (Fifteen milimetres) diameters long nose brass bib tap (Superior or heavy type) Cera, Jaquuar and Hindware complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 15mm (Fifteen milimetres) dia long body brass bib tap (Superior or heavy type) Cera, Jaquuar and Hindware complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 15mm (Fifteen milimetres) C.P. brass angle valve without nuts and pipe Cera, Jaquuar and Hindware complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing P.V.C. connection 300x450mm (Three hundred into four hundred fifty millimetres) length with check nut and brass union Cera, Jaquuar and Hindware complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PTMT Coloured/white high density polyethylene / poly propylene 10.00 ltrs (Ten litres) capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (Fifteen millimetres) nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm (Forty millimetres) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) complete and as per direction of Engineer- Incharge, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube as directed by the Engineer-in-Charge, including entire carriage of materials within all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) Cera or its equivalent approved quality tube fitting and clamps including making good the wall, ceiling and floor as directed by the Engineer-Incharge including carriage of materials within all leads, lifts and other incidentals.

15mm (Fifteen milimetres) nominal bore

20mm (Twenty milimetres) nominal bore

Providing and fixing PTMT concealed stop cock with flange of approved quality and colour complete including entire carriage of materials within all leads lifts and other incidentals.

Providing and fixing 600x120mm (Six hundred into One hundred twenty milimetres) glass shelf with C.P. brass. (Heavy duty makes) brackets and guard rail complete fixed to wooden plugs with C.P. brass screws as directed by the Engineer- in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PTMT pillar cock fancy of approved quality and colour 15 (Fifteen) complete including entire carriage of materials within all leads lifts and other incidentals.

Providing and fixing Mixer for kitchen sink with casted swinging spout at top Cera or its equivalent complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals.

Saini