Construction of Store room at product plant of Thiruvananthapuram Diary

Amount

Dismantling of existing Aluminium clading sheet tile by mechanical way.Which includes scafolding charges.

Providing and laying in position RCC (1:1.5:3) thick for flooring, beams, slabs using 20 mm nominal sizeaggregate obtained from approved quarry including mechanical mixing, form/shuttering work in correct level, vibrating, compaction, finishing, curing, etc in slope if needed as per site condition; complete all as per specifications.

Steel Reinforcement for R.C.C work including straightening, cutting, bending , placing in position and binding all complete above plinth level. Thermo - Mechanically Treated bars of grade Fe-500D or more

Solid block masonry using pre cast solid blocks (factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM1:6 ( 1 cement : 6 coarse sand) etc complete

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel roofing accessories 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete Ridges plain (500 - 600 mm)

Providing and fixing Turbo ventilators above the roofing sheet for hot air escape, having a throat dia of 16 inch, height of 23.25 inch and top width of 25 inch having a exhaust cap 4MI wind CFM of 950 and shipping weight of 35lbs

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 TypeA, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes.110 mm diameter

Supplying and fixing anodised Aluminium Sliding Window (1000×1500) fully glazed outer frame made of 100mm×45mm with threashold plates and shutter section out of 50mm× 45mm (wall thickneess 2mm for all sections), hinges of requred number and size and all necessary accesories etc complete

12 mm cement plaster of mix:1:4 (1 cement : 4 coarse sand)

Providing and fixing false ceiling with 7.5 mm thick PVC plain panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

SASIDHARAN NAIR J (BID ID -1982190)

GLAZE SPOT FACILITY MANAGEMENT SERVICES LLP (BID ID -1983341)