Tenderization for ARC Work of Laying testing & commissioning of 11/22 KV UG XLPE CABLE with 11/22 KV Cable End Termination & ST joint Kits (to be Supplies by Agency) along with Dismantle of HT,LT & TC works under Kharvasa sub division and if required any other Sdn under jurisdiction of Sachin Division under ND and if Required Any other Scheme.

ITEM CODE Details of Works Qty Unit Amount

Labour charge for excavation of cable trench of 400mm width x

1200mm depth, in any type of soil for laying of cable of size up to

240 mm2 (For additional cable 200 mm additional width shall be

considered i.e. half trench length is to be considered)

Labour charge for excavation of cable trench of 600mm width x

1200mm depth, in any type of soil for laying of cable of size up to

240 mm2 (For additional cable 200 mm additional width shall be

considered i.e. half trench length is to be considered)

Labour charge for excavation of cable trench of 400mm width x

1500mm depth, in any type of soil for laying of cable of size up to

240 mm2 (For additional cable 200 mm additional width shall be

considered i.e. half trench length is to be considered)

Labour charge for laying of 11kV / 22 kV XLPE Cable of size up to

240 mm2 & preparation of sand layer 100mm thick, in the cable

trench & covering the cable with 150 mm dia (Inner), thickness

mm, 1.0 meter long RCC half round muffs and providing and

fixing of 4inch width yellow colour polyethylene tape with printing

"CAUTION ELECTRIC CABLE BELOW" at 0.75 m depth from

ground surface after laying cable in trench. This will provide

indication that electric cable is passing underground so as to

protect cable from mechnical injuries, refilling the same, as per

Instruction of Engineer in Charge (EIC).

Labour charge for horizontal drilling using Auger machine without

damage to surface road at max 2.0 mtrs depth & putting of

kg/cm2 , class-4,Green color, 110mm O.D. , 8.5mm thickness

H.D.P.E. pipe confirms to IS 4984-1987(3rd revision) and BIS

certification and laying of 11KV/22KV XLPE cable of size up to

240 mm2 in HDPE pipe, as per Site Condition (excluding cost of

pipe). The detail map obtained from HDD machine and excell

sheet(hard and soft copy) indicating the respective depth and

distance from adjacent landmark for each segment for HDD is

must required to be submitted. HDD to be carried out at depth

mtrs to 2.0 mtrs as per site conditions and as per instruction of

Labour charge for horizontal drilling manually without damage to

surface road at max 2.0 mtrs depth & putting of 6.11 kg/cm2

class-4,Green color, 110mm O.D. , 8.5mm thickness H.D.P.E.

pipe confirms to IS 4984-1987(3rd revision) and BIS certification

and laying of 11KV/22KV XLPE cable of size up to 240 mm2 size,

as per Site Condition (excluding cost of pipe). The detail map and

excell sheet(hard and soft copy) indicating the respective depth

and distance from adjacent landmark for each segment of cable

to be submitted. Drilling to be carried out at depth Minimum

mtrs to 2.0 mtrs as per site conditions as per instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color, 110mm O.D. ,

mm thickness H.D.P.E. pipe confirms to IS 4984 and BIS

certification for laying of underground 11KV / 22KV XLPE cable

up to 240 mm2 size.

Labour work for RCC concreting on disputed location and

repairing of damage portion of road crossing for the work carried

out for roads crossing as well as concreting & muffing of ploes

including all materials (1:2:4)

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

Providing & fixing concrete stone route marker of 300 mm width x

150 mm thick x 650 mm height embedded in earth at least

mm below & 350 mm above ground level respectively at distance

approx 50 meters along the length of cable. The RCC concreting

(1:2:4)(all necessary maeterials will be in bidder's scope) of route

marker is to be carried out 300 mm width x 150 mm thick x

9 9925000009 mm below ground level as per instruction of EIC. The route No. 446

marker should be with name of company with approved yellow

colour-DGVCL. The distance from marker to cable and cable

depth with feeder name etc., marked with arrow sign is to be

painted on it.The route marker is to be fixed at location near to

any fixed permanent location (not necessary to fix exact on top of

cable) as per instruction of EIC.

Erection of D.P. (double pole) structure using 9 / 11 Mtr. RSJ pole

with cable connection arrangement along with fitting of necessary

10 9925000010 fabrication for 11KV cable including excavation of pit & refilling of No. 2026

earth as per instruction of EIC. (Exclusive of concreting & muffing

Erection of Single pole structure using 9 / 11 Mtr RSJ pole with

cable connection arrangement along with fitting ofnecessary

11 9925000011 fabrication for 11KV/22 KV cable including excavation of pit & No. 1047

refilling of earth as per instruction of EIC. (Exclusive of concreting

& muffing of poles)

Erection of D.P. (double pole) structure using 8.0 Mtr. PSC pole

with cable connection arrangement along with fitting of necessary

12 9925000012 fabrication for 11KV cable including excavation of pit & refilling of No. 1416

earth as per instruction of EIC. (Exclusive of concreting & muffing

Erection of Single pole structure using 8.0 Mtr PSC pole with

cable connection arrangement along with fitting ofnecessary

13 9925000013 fabrication for 11KV/22 KV cable including excavation of pit & No. 613

refilling of earth as per instruction of EIC. (Exclusive of concreting

& muffing of poles)

Labour charge for erecting of 11kV / 22 kV XLPE cable of size up

to 240 mm2 on DP Structure with fixing of 02 Nos polymer cleats per

on top and middle part.Polymer cleats, nut bolts etc. fixing Job

material to be provided by contractor.

Providing & fixing of 6.11kg/cm2 , class-4,Green color, 110mm

O.D. , 8.5mm thickness H.D.P.E. pipe confirms to IS 4984 and

BIS certification on the erected DP structure for the mechanical

protection of cable by inserting the cable inside HDPE pipe. The Per

HDPE pipe shall be erected in such a way that 300mm shall be Job

below the ground level and the rest 2700 mm shall be supported

on the DP Structure with 01 No Polymer cleat.All materials

including polymer cleat and Nut bolt to be provided by contractor.

Providing and fixing of pipe type earthing from 80 mm dia class-B

GI pipe with pit to be filled with salt & coke and construction of

chamber as per DGVCL Drg. No. dg /100 for DP and cable. The

earthing pit should be joined with cable by G.I. strip of size 1”

width & 2 mm thick. All material GI pipe, Coke, Salt etc will be

supplied by bidder.

Supply & fixing of heat shrink type end terminations

(outdoor) for upto 11kV 3C x 185 mm2 size XLPE cable as per

DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations (outdoor) for

18 9925000018 upto 22 kV 3C x 185 mm2 size XLPE cable as per DGVCL No. 6231

technical specification)

Supply & fixing of heat shrink type end terminations (indoor) for

19 9925000019 upto 11kV 3C x 185 mm2 size XLPE cable as per DGVCL No. 3635

technical specification)

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

Supply & fixing of heat & shrinkable end terminations (indoor) for

20 9925000020 upto 22 kV 3C x 185 mm2 size XLPE cable as per DGVCL No. 6231

technical specification

Supply & fixing of heat shrinkable straight through joint for upto

21 9925000021 11kV 3C x 185 mm2 size XLPE cableas per DGVCL technical No. 6774

Supply & fixing of heat shrinkable straight through joint type for

22 9925000022 upto 22kV 3C x 185 mm2 size XLPE cable as per DGVCL No. 11590

technical specification

Labour charge for excavation of 2100mm long x 1200mm wide x

1200 mm deep joint pits for installation of 11kV / 22kV Straight

through joints as per instruction of engineer-in-charge & covering

the cable with 150 mm dia (Outer), thickness 25 mm, 1.0 meter

long RCC half round muffs & refilling same as per instruction of

Providing and fixing of insulating bus bar, made from 11KV/22KV

XLPE cable after removal of semi conducting layer and applying

of PVC heat shrinkable anti-tracking core insulating tubing

(1.1KV), on both end terminal using Aluminium long barrel heavy

24 9925000024 duty up to 240 sq mm lugs, Aluminium bus connector. Taping with No. 1661

PG- clamp for bus conductor as per drawing and as per

instruction of EIC. The Alluminium lugs and PG clamp shall be

covered with 11KV/22KV HT insulating tapes.(11KV/22KV XLPE

cable will be in scope of DGVCL while all other materials will be in

bidder's scope)

Testing of cable at various points and commissioning the

25 9925000025 feeder as per instruction of engineer-in-charge.Test result No. 2125

shall be submitted by contractor with bill.

Preparation and submission of 6 (six) copies, of complete layout

drawings with GIS mapping as per actual cable routing showing

road crossing, HDPE pipe sleeving, jointing locations, markers

Providing and fixing of Sign Board at junction point Made out of

mm aluminium sheet size 750x300 mm (2.5 x 1ft) rectangle, as

per design, pre treated with phosphate process and acid etching

coated with one coat of epoxy primer and two coats of best

quality paints, refloctrorised with Hi-Intensity retro – reflective

sheeting as per the latest and frame fabricated from suitable size

iron angle. The Sign Board is to be fixed on the base prepared

from channel and bracing angles which is grouted by means of

cement concreting of 1:2:4 for size of 300 mm dia x 800 mm

height (500 mm to be grouted in ground). The details to be

displayed on sign board will be given by In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing and fixing of Sign Board (Danger Board) on Distribution

Transformer Centers

Made out of 2mm aluminium sheet size 300x300mm (1x1ft) as

per design, pre treated with phosphate process and acid etching

coated with one coat of epoxy primer and two coats of best

28 9925000028 quality paints, refloctrorised with Hi-Intensity retro-reflective No. 2805

sheeting as per the latest and frame fabricated from suitable size

iron angle. The Sign Board (Danger Board is to be fixed at the

location as per instruction of In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing & fixing of aluminium tag of size 250 mm (L) x 75 mm

(W) from 3 mm aluminium sheet along with 1.0 mm dia aluminium

binding wire for fixing of aluminium tag near end termination joint

29 9925000029 at DP structure for identifyng the cable. The details of feeder i.e. No. 83

11 / 22 KV with feeder name shound be punched on the tag by

letter punch of size 16 mm as per instruction of In-charge

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

Supply & fixing of heat shrink type end terminations (outdoor) for

30 9925000030 11kV 3C x 240 mm2 size XLPE cable as per DGVCL technical No. 4427

Supply & fixing of heat & shrinkable end terminations (outdoor) for

31 9925000031 22 kV 3C x 240 mm2 size XLPE cable as per DGVCL technical No. 6231

Supply & fixing of heat shrink type end terminations (indoor) for

32 9925000032 11kV 3C x 240 mm2 size XLPE cable as per DGVCL technical No. 4338

Supply & fixing of heat & shrinkable end terminations (indoor) for

33 9925000033 22 kV 3C x 240 mm2 size XLPE cable as per DGVCL technical No. 6231

Supply & fixing of heat shrinkable straight through joint for 11kV

34 9925000034 3C x 240 mm2 size XLPE cableas per DGVCL technical No. 6829

Supply & fixing of heat shrinkable straight through joint type for

35 9925000035 22kV 3C x 240 mm2 size XLPE cable as per DGVCL technical No. 11590

Installation, Testing and commissioning of 11 KV,630 A SCADA

Compatible, RRL type- 3 Way RMU including Two numbers of

earthings as per Drawing (material is in bidder's scope) and as

per DGVCL Technical specification.

Installation, Testing and commissioning of 11 KV,630 A SCADA

Compatible, RRLL type- 4 Way RMU including Two numbers of

earthings as per Drawing (material is in bidder's scope) and as

per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A SCADA

Compatible, RRL type-3 Way, RMU including Two numbers of

earthings as per Drawing (material is in bidder's scope) and as

per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A SCADA

Compatible, RRLL type-4 Way, RMU including Two numbers of

earthings as per Drawing (material is in bidder's scope) and as

per DGVCL Technical specification.

Construction of plinth for 11KV, RRL type- 3 Way (i.e Two

numbers of Isolator & One number of Breaker) Ring Main Unit as

per DGVCL's technical specification mentioned in drawing no:

Drg. 11kv-01. All required material will be supplied by contractor.

Construction of plinth for 11KV, RRLL type- 4 Way (i.e Two

numbers of Isolator & Two number of Breaker)Ring Main Unit as

per DGVCL's technical specification mentioned in drawing no:Drg.

11kv-02.All required material will be supplied by contractor.

Construction of plinth for 22KV, RRL type- 3 Way (i.e Two

numbers of Isolator & One number of Breaker) Ring Main Unit as

per DGVCL's technical specification mentioned in drawing no:

Drg. 22kv-01. All required material will be supplied by contractor.

Construction of plinth for 22KV, RRLL type- 4 Way (i.e Two

numbers of Isolator & Two number of Breaker)Ring Main Unit as

per DGVCL's technical specification mentioned in drawing no:Drg.

22kv-02.All required material will be supplied by contractor.

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

Modifications e.g.Providing and fixing of Terminal protectors i.e.

Re-use able boot (HT Side 11/22KV, LT Side 1.1KV) including

11/22 KV insulating taps and L.T.(1.1 KV) insulating taps ,Busbar,

Tapping from Bus Bar (11/22 KV XLPE cable) through P.G.

Clamp for H.T. Jumper to D.O. Fuse to bushings of Transformer

Center, providing & Fixing of jumper and providing & fixing of Heat

Shrinkable Anti Tracking Core Insulating Tubing (Insulation Level

44 9925000046 11/22 KV) in H.T. jumper , Clamping arrangement of cable No. 10152

support frame on both side of existing Over Head type Distribution

Transformer to utilize in Under Ground cable network as per

drawing & as per instruction of Engineer incharge. All live parts

i.e. PG-Clamp, connections of D.O.fuses, HT bushings etc . shall

be covered with fixinng of 11/22 KV HT insulating tapes. ( 11/22

KV XLPE cable will be in scope of DGVCL while all other

materials will be in bidder's scope ) .

Laying of any size of 11/ 22 KV XLPE /PILC Cable in redaymade cable

trench or in open space

46 9925000060 Labour charges for Lying of O/H XLPE cable pole to pole KM 70320

Supply of 150 mm dia (Inner), thickness 25 mm, 1.0 meter long

RCC half round pipe

Laying (Including Installation , Testing and Commissioning) of

various size of 11 KV XLPE Insulated alluminium armoured cable

in ground 1200 mm Deep , 300 mm Wide Trench, Providing sand

cushioning below (75 mm thick layer of sand ) and above (75 mm

thick layer of sand ) of the cable and covering it with RCC Half

round hume pipe (150 mm inner dia with thickness of 30 mm,1

meter length) before refilling pre-bonding / warning tap should

provide below 700 mm from the ground level and back filling the

same to make ground level as per original. As per Specification

and drawing og UGVCL. ( RCC Half Round pipe should be

provide thorughout on cable wihtout gap, only cable will be

supplied by DGVCL)

Laying (Including Installation , Testing and Commissioning) of

various size of Double Circuit 11 KV XLPE Insulated alluminium

armoured cable in ground 1200 mm Deep , 500 mm Wide Trench,

Providing sand cushioning below (75 mm thick layer of sand ) and

above (75 mm thick layer of sand ) of the cable and covering it

with RCC Half round hume pipe (150 mm inner dia with thickness

of 30 mm,1 meter length) before refilling pre-bonding / warning tap

should provide below 700 mm from the ground level and back

filling the same to make ground level as per original. As per

Specification and drawing og UGVCL. ( RCC Half Round pipe

should be provide thorughout on cable wihtout gap, only cable will

be supplied by DGVCL)

Layingt of HDPE Pipe Confirming to IS 4984:1955 (Ammendment

No 2) having diameter 160 mm and minimum thickness 5 mm at a

minimum depth of 1200 mm below the road surface by push

thorugh method by drilling the road with HDD machine/manually

without breaking the road surface and laying of any size of HT/LT

XLPE insulated alluminium armoured cable through the duct as

per the instruction of EIC and specifications. (Without cost of

HDPE Pipe , Cable will be supplied by DGVCL)

Supply of HDPE Pipe having 160 mm diameter , minimum

4 thickness 7.3 mm as per IS (ammendment no 2 - IS 4984:1995) Meter 640

of PE- 100 , 6 kg/cm2 , for laying of 11 KV XLPE Cable

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

Proving and Fixing HT push on/heat shrink type End Indoor

termination kit Preferably 3m(m-seal) or Raychem make at

switchgear end boxes, transformer (PAD/Pole mounted) for 3 core

11 kV XLPE Aluminium Conductor Armoured cable as specified

with connection of leads including cutting, stripping of cable,

insulations, providing compression type terminal ,crimping of lugs

with suitable crimping tool, indoor application.

For 300 mm2 HT XLPE Cable

Proving and Fixing HT push on/heat shrink type End Outdoor

termination kit Preferably 3m(m-seal) or Raychem make at

switchgear end boxes, transformer (PAD/Pole mounted) for 3 core

11 kV XLPE Aluminium Conductor Armoured cable as specified

with connection of leads including cutting, stripping of cable,

insulations, providing compression type terminal ,crimping of lugs

with suitable crimping tool, outdoor application.

For 300 mm2 HT XLPE Cable

Proving and Fixing HT push on/heat shrink type Straight Joint

Preferably 3m(m-seal) or Raychem make for 3 core 11 kV XLPE

Aluminium Conductor Armoured cable as specified with

7 connection of leads including cutting, stripping of cable, No. 8040

insulations, providing compression type terminal ,crimping of lugs

with suitable crimping tool.

For 300 mm2 HT XLPE Cable

DISMENTALLING Schedule B-3

DISMENTALLING OF 8 MTR PSC POLE WITH CREDITING OF

1 9926000033 FABRICATION AT STORE & STACKING OF POLE SAFELY ON No. 678

ROAD SIDE OR CREDITING TO DEPARTMENTAL STORE

DISMENTALLING OF 10 MTR PSC POLE WITH CREDITING OF

2 9926000034 FABRICATION AT STORE & STACKING OF POLE SAFELY ON No. 1350

ROAD SIDE OR CREDITING TO DEPARTMENTAL STORE

DISMENTALLING OF TRANSFORMER CENTRE (8 MTR PSC

POLE) (WITH TRANSFORMER) WITH CREDITING OF

3 9926000035 FABRICATION & TRANSFORMER AT STORE & STACKING OF No. 3975

POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

DISMENTALLING OF TRANSFORMER CENTRE (8 MTR PSC

POLE) (WITHOUT TRANSFORMER) WITH CREDITING OF

FABRICATION AT STORE & STACKING OF POLE SAFELY ON

ROAD SIDE OR CREDITING TO DEPARTMENTAL STORE

DISMENTALING OF RSJ (9/11 METER) POLE AND

CREDITING THE OLD MATERIAL TO STORE

DISMENTALING OF TRANSFORMER CENTER ON

10MTR,270KG PSC POLE(WITHOUT TRANSFORMER) WITH

6 9926000043 CREDITING OF FABRICATION AT STORE AND STACKING OF No. 2828

POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

DISMENTALING OF TRANSFORMER CENTER ON

10MTR,270KG PSC POLE(WITH TRANSFORMER) WITH

7 9926000044 CREDITING OF FABRICATION AT STORE AND STACKING OF No. 5332

POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

DISMENTLING OF 11KV ABC OF 3*95 SQ MM +80 SQ MM

8 9926000045 AND CREDITING FITTING OF ALL ACESSARIES AND KM 20515

FABRICATION TO DEPARTMENTAL STORE

DISMENTLING OF 22 KV ABC OF 3*70 SQ MM +95 SQ MM

9 9926000046 AND CREDITING FITTING OF ALL ACESSARIES AND KM 25643

FABRICATION TO DEPARTMENTAL STORE

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

DISMENTALING OF LT ABC OF 1*35 SQ MM + 1*25 SQ MM

AND CREDITING FITTING OF ALL ACESSARIES TO

DEPARTMENTAL STORE.

DISMENTALING OF LT ABC OF 3*50 SQ MM +1*25 SQ

MM+1*35 SQ MM AND CREDITING FITTING OF ALL

ACESSARIES TO DEPARTMENTAL STORE.

DISMENTALING OF LT ABC OF 2*50 SQ MM +1*25 SQ MM+

SQ MM AND CREDITING FITTING OF ALL ACESSARIES TO

DEPARTMENTAL STORE.

Supply and Installation of 11/22 kV Distribution Transformers HT

13 9926000086 Terminal protector (UV Resistance) with using 95/120/150 sq.mm 1700

long barrel aluminum lug. (1Set = 3 Nos i.e. on R, Y, B)

Supply & Installation of HT EPR Tap on 11/22 kV Distribution

Transformer with replacement of bare conductor by HT ABC

14 9926000087 conductor (DO bottom side to transformer) after removal of semi 1800

conductor by HT ABC (6 inch both side). HT ABC to be supplied

by DGVCL. (1Set = 3 Nos i.e. on R, Y, B)

Supply, Installation, Testing and Commissioning of Maintenance

Free, Ready Capsule, Pipe-In-Cage (Pic) Type, Earth Electrodes

15 9926000088 for HT Feeder Pole Having 2000 mm Electrode Length as per the No 4150

Tender Specifications and Drawing. (All Materials Will Be

Supplied By Agency)

Supply, Installation, Testing and Commissioning of Maintenance

Free, Ready Capsule, Pipe-In-Cage (Pic) Type, Earth Electrodes

16 9926000089 for HT Feeder Pole Having 3000 mm Electrode Length as per the No 5450

Tender Specifications And Drawing. (All Materials Will Be

Supplied By Agency)

Supply and Installation of 25 X 3 mm GI Strip having hot dip-

galvanized-zinc coating of 80-100 microns without any joints or

welding. Both the end of the GI strip should be connected with GI

nut bolts and required fabrication work for giving separate earthing

connections to(1) Neutral of the transformer(2) MS structures of

the transformer center (Approximately 25 meter GI strip per

transformer centre- as per requirement and instruction of

Engineer in- charge) (All Materials will be supplied by Agency)

Supply and Installation of uPVC standard make Pipe of 1.25"

diameter for covering GI strip with UV protected Cable Ties of

18 9926000092 X 7.6 mm size to bind with pole face(Approximately 25 meter Meter 85

uPVC pipe for GI strip covering per transformer centre -as per

requirement and instruction of Engineer in-charge.

Supply & fixing of upto 33 kV Conductor sleeve for Busbar to

Drop out Fuse and Drop

19 9926000093 out fuse to Transformer H.T. including Busbar (12 mm sleeve) as 5600

specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conductor sleeve for Busbar to

Drop out Fuse and Drop

20 9926000100 out fuse to Transformer H.T. without Busbar (12 mm sleeve) as 2800

specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conductor sleeve for Busbar to

Drop out Fuse and Drop

21 9926000094 out fuse to Transformer H.T. including Busbar(15 mm sleeve) as 6050

specification. (All Materials will be supplied by Agency)

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

Supply & fixing of upto 33 kV Conductor sleeve for Busbar to

Drop out Fuse and Drop

22 9926000101 out fuse to Transformer H.T. without Busbar(15 mm sleeve) as 3090

specification. (All Materials will be supplied by Agency)

Supply & fixing of Disc type Red Color FRP(Non-flammable)

material with Weather

23 9926000095 resistant, Non-conductive bird guard OD=300 MM, ID=33 MM, No 80

Width =1.25 MM, one

side cut from ID to OD. (All Materials will be supplied by Agency)

Providing and fixing of LT Terminal protectors i.e. Re-useable

24 9926000096 boot (LT Side 1.1 kV) including LT (1.1 kV) insulating taps. All live No 900

part at LT side shall be covered with fixing of LT insulating taps.

25 Nylon Net around Transformer Center

25.2 9926000098 Nylon Dori

Labour charge for fitting Nylon Net (All fabricated material for Per

fitting nylon net shall be provided by DGVCL) TC

Dismentalling of existing Dist.X'mer center(RSJ /STP POLE)

26 9924000055 25/63/100/200 KVA with all fabrication & creditig the old material No. 5528

27 9924000056 Disconnection from LT pole 1 phase No. 46

28 9924000058 Disconnection from LT pole 3 phase No. 66

Dismentaling & removing of service line from pole & crediting to

Dismentaling & removing of service line from pole & crediting to

Total of Schedule B1 + B2 + B3 is Rs. TOTAL

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

1.DGVCL will provide key material like M.S. materials,ABC/Bare

conductors,PSC/RSJ Poles,Insulators,Fabricated materials etc. to

the contractor.

2.All fabricated items shall be fabricated as per DGVCL approved

drawing and by welding rods confirming to the relevent ISI

specification and as directed by Engineer in charge.

3.Necessary electricity connection for fabrication items shall be

provided by DGVCL on payment of required charge for

connection & electricity bill of the same shall be paid by the

4.All the rates are inclusive of PF & Exclusive of GST applicable

5.All steel material are to be painted as below:

(a) Scrubbing of rusted surface properly before applying the

paints on to the RSJ poles & steel fabricated materials of

RSJ/PSC poles is must required.

(b) Two coats of approved ISI mark red oxide (primer) is to be

properly painted for the RSJ poles & steel fabricated materials of

(c) Two coats of approved ISI mark silver paint (i.e. triple

mangoes or equivalent quality silver paint) is to be properly

painted on to the RSJ poles & steel fabricated materials of

1. Excavation, Drilling and Cable laying should be done with all

road safety measures such as hard barricading, displaying

“DANGER” sign and “DGVCL - Work in Progress” on it with light

reflective strips or paint. Proof of all barricading and safety

equipment need to submit.

2. Cable laying should be done through roller (not through

tractor or pulling by any other vehicles).

3. Ownership document regarding roller/pulling machine and

HDD machine need to submit or agreement with agency of above

narrated machine regarding work for this tender required to

4. Trail pit excavation and De-excavation should be done

simultaneously so that any chance of road accident can be

5. Three no of Polymer cleat should be provided on rising cable

for proper fitting and if it is not feasible to provide third polymer

cleat at the bottom than two nos of polymer cleat on upper side

and strap strip on bottom end required to install for proper fitting

of rising cable.

Deputy Engineer (Tech)

Technical 6. 100% videography of cable laying along with landmark

Terms location of cable laying required to be done and submit Pen drive

Sachin Division

to the concern engineer for their verification.

7. Aluminum strip required to use to connect end of cable at

cable rising location as per instruction of Engineer in charge. Also

no joints will be allowed in GI strip for cable Earthing and strip will

be connected through GI bolts only.

8. Issues regarding ROW on field should be resolved by

contractor itself.

9. Testing & measuring equipment: - 5 KV Digital insulation

testers, Digital Earth clamp meter for measurement of Earthing

and leakage current, Digital Rodometer with NABL accredited

agency valid test certification.

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS

Letter No: DGVCLSDUR/0201/07/2026 Approved Date: 27-07-2026 05:32

10.Earthing value & Insulation Resistance (IR) value of all

location along with Geo tagged (longitude & latitude) wise testing

and measured value photograph need to submit with Bill.

11.Depth chart should be provided at every 100 meter with

mentioning landmark.

12. Partial Discharge test to be carried out on sample part of

cable before charging as decided by in charge engineer.

13. Qualified cable jointer with Minimum five years of experience

required with necessary certification regarding qualification and

specific experience.

14. Performance Bank Guaranty required to submit 5% of tender

value for two years against cable joint failure. Moreover, cable

joint failure or end termination failure will have to repair within

Hrs for 2 years of guaranty period.

15. Fixing of mechanical protection HDPE pipe at rising should be

properly buried as per specification.

16. Fixing of Route marker strictly as per specification.

17. Minimum annual Turnover should be at least tender estimated

value and in addition to CVC guideline narrated in tender for UG

cable laying work.

18. Marking of feeder name, direction and location on cable is

compulsory during final scrutiny to declare work completion.

19. End termination and straight joint kit should be of premium

quality as specified in Annexure-2. Technical specifications for the

same to be submitted along with bid.

20. Cable straight joint should be done with mid span joint instead

of long barrel Lug.

21. Agreement with vendor of cable joint kit and End termination

kit to supply for this tender for concern bidder should be submit at

the time of bidding.

File No: DGVCLSDUR/MSC/e-file/4523/2026/1064/Billing

Approved By: Executive Engineer,Technical,DGVCLDOS