Police R&M

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, ETC. COMPLETE FOR FINISHED ITEM OF WORK EXCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308).

CEMENT CONCRETE (1:5:10) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATION BED AND UNDER STONE SLAB FLOORING. (APSS NO: 402).

FILLING WITH CARTED GRAVEL OBTAINED FROM APPROVED QUARRY IN LAYERS NOT EXCEEDING 15 CM THICK, IN BASEMENTS, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, , LABOUR CHARGES, HIRE CHARGES OF T & P BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

RE-FILLING WITH EXCAVATED EARTH IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT. (APSS NO. 309 & 310)

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM WITH A COMPRESIVE STRENGTH NOT LESS THAN 50 KG/SQM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SEINIORAGE CHARGES, SCAFFOLDING AND CURING ETC., CPOMPLETE FOR FINISHED ITEM OF WORK. BASEMENT WALLS 225 MM THICK.(APSS NO. 501&504).

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM WITH A COMPRESIVE STRENGTH NOT LESS THAN 50 KG/SQM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. SUPERSTRUCTURE WALLS 225 MM THICK GROUND FLOOR (APSS NO. 501&504).

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR FOOTINGS (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR PLINTH BEAM (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR COLUMNS GF. (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR GROUND FLOOR LINTELS . (APSS NO.403)

VRCC M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, FOR SUNSHADES OF 50MM (2") AVERAGE THICK INCLUDING DRIP COURSE OF SIZE 40MM WIDE X 20MM HEIGHT IN CEMENT MORTAR (1:4)PROP - GROUND FLOOR. (APSS NO.403)

PROVIDING AND FIXING FACTORY MADE UPVC WHITE COLOUR SLIDING GLAZED WINDOW UPTO 1.50 M IN HEIGHT DIMENSION ,THREE TRACK THREE PANELS SLIDING WINDOW WITH FLY PROOF SS WIRE MESH (TWO NOS. GLAZED & ONE NO. WIRE MESH PANELS) MADE OF (SMALL SERIES) FRAME 92 X 44 MM & SASH 32 X 60 MMBOTH HAVING WALL THICKNESS OF 1.9 ± 0.2 MM AND SINGLE GLAZINGBEAD OF APPROPRIATE DIMENSION (AREA OF WINDOW UPTO 1.75 SQM).COMPRISINGOF UPVC MULTI-CHAMBEREDFRAME WITH IN-BUILT ROLLER TRACK AND SASH EXTRUDED PROFILES DULY REINFORCEDWITH 1.60 ± 0.2 MM THICK GALVANIZED MILD STEEL SECTION MADE FROM ROLLFORMING PROCESS OF REQUIRED LENGTH (SHAPE & SIZE ACCORDING TO UPVC PROFILE), APPROPRIATE DIMENSION OF UPVC EXTRUDED GLAZING BEADS AND UPVC EXTRUDED INTERLOCKS, EPDM GASKET, WOOL PILE, ZINC ALLOY (WHITEPOWDER COATED) TOUCH LOCKS WITH HOOK, ZINC ALLOY BODY WITH SINGLE NYLONROLLERS (WEIGHT BEARING CAPACITY TO BE 40 KG), G.I FASTENERS 100 X 8 MMSIZE FOR FIXING FRAME TO FINISHED WALL AND NECESSARY STAINLESS STEEL SCREWSETC. PROFILE OF FRAME & SASH SHALL BE MITRED CUT AND FUSION WELDED AT ALLCORNERS, INCLUDING DRILLING OF HOLES FOR FIXING HARDWARE'S AND DRAINAGE OFWATER ETC. AFTER FIXING FRAME THE GAP BETWEEN FRAME AND ADJACENT INISHEDWALL SHALL BE FILLED WITH WEATHER PROOF SILICON SEALENT OVER BACKER ROD OFREQUIRED SIZE AND OF APPROVED QUALITY, ALL COMPLETE AS PER APPROVED DRAWING& DIRECTION OF ENGINEER-IN-CHARGE INCLUSIVE OF COST OF SINGLE / DOUBLE GLASS PANES, WIRE MESH AND SILICON SEALENT . NOTE: FOR UPVC FRAME AND SASH EXTRUDED PROFILES MINUS 5% TOLERANCEIN DIMENSION I.E. IN DEPTH & WIDTH OF PROFILE SHALL BE ACCEPTABLE.VARIATION IN PROFILE DIMENSION IN HIGHER SIDE SHALL BE ACCEPTED. BUT NO EXTRA PAYMENT ON THIS ACCOUNT SHALL BE MADE.

Providing and fixing factory made uPVC white colour casement/Casementcum fixed glazed door comprising of uPVC multi-chambered frame, sashand mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll formingprocess of required length (shape & size according to Upvc profile),uPVC extruded glazing beads of appropriate dimension,EPDMgasket,zinc alloy (white powder coated) 3D hinges and one handle oneach side of panels along with zinc plated mild steel multi pointlockinghavingtransmission gear, cylinder with keeps and one side key, G.Ifasteners100 x 8 mm size for fixing frame to finished wall and ecessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut andfusion welded at all corners, mullion (if required) shall be also fusionweldedincluding drilling of holes for fixing hardware's and drainage ofwater etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required sizeand of approved quality, all complete as per approved drawing & directionof Engineer-in-Charge inclusive of cost of Single / double glass panes and silicon sealent . Note: For uPVC frame, sash and mullion extruded profiles minus 5%tolerance in dimension i.e. in depth & width of profile shall be cceptable.Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made.Casement door with 3D hinges made of (big series) frame67x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00sqm).

ORNAMENTAL PLASTERING TO CEILING 12MM THICK WITH A BASE COAT OF 8 MM THICK IN CM (1:5) PROP. AND FINISH COAT OF 4MM THICK IN CM (1:3) PROP. WITH DUBARA SPONGE FINISHING, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK. GROUND FLOOR (APSS NO: 901 & 904)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. WITH DUBARA SPONGE FINISHING, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE.FOR FINISHED ITEM OF WORK. -GROUND FLOOR (APSS NO: 901&904)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. WITH DUBARA SPONGE FINISHING, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES BUT EXCLUDING SEIGNIORAGE CHARGES ETC., COMPLETE.FOR FINISHED ITEM OF WORK.FOR BASEMENT (APSS NO: 901&904)

Providing dadooing to internal walls with glazed Red or White full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete including seigniorage charges, etc., complete for finished item of work for Ground floor.

FLOORING WITH NANO POLISHED /STAIN FREE SOLUBLE SALT PORCELAIN VITRIFIED TILES SCREEN PRINTED OF SIZE 600 X 600 MM AND THICKNESS BETWEEN 8-10 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, INCLUDING SEIGNIORAGE CHARGES, ETC., COMPLETE FOR FINISHED ITEM OF WORK, . -FIRST FLOOR

PROVIDING SKIRTING TO INTERNAL WALLS / RISERS OF STEPS NANO POLISHED /STAIN FREE SOLUBLE SALT PORCELAIN VITRIFIED TILES SCREEN PRINTED OF SIZE 600 X 600 MM AND THICKNESS BETWEEN 8-10 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS LENGTH EQUAL TO FLOORING STONES, SET OVER BASE COAT OF CM (1:5) 12 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE TILES, CEMENT, SAND AND WATER ETC., COMPLETE INCLUDING SEIGNIORAGE CHARGES, ETC., COMPLETE FOR FINISHED ITEM OF WORK GROUND FLOOR.

PAINTING TO NEW WALLS WITH 2 COATS OF PREMIUM PLASTIC EMULSION PAINT OF APPROVED BRAND AND SHADE OVER A BASE COAT OF APPROPRIATE PRIMER OF APPROVED BRAND, MAKING 3 COATS IN ALL TO GIVE AN EVEN SHADE AFTER THOURUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC. COMPLETE FOR FINISHED ITEM OF WORK AS PER SS 911 FOR INTERNAL WALLS

PAINTING TO EXTERIOR FACES OF WALLS WITH EMULSION PAINT OF APPROVED MAKE (ACE FROM ASIAN PAINT) AND COLOUR 2 COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 ML OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1 COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, BRUSHES, ALL INCIDENTAL, OPERATIONAL & LABOUR CHARGES, CURING, SCAFFOLDING ETC., COMPLETE FOR FINISHED ITEM OF WORK. ALL FLOORS (APSS NO:908)

PROVIDING "HYSD" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER (Fe - 500 GRADE AS PER IS 1786 - 1979)FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED

SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.S. TUBES OF ALL SIZES

PAINTING TO NEW IRON WORK TWO COATS WITH SYNTHETIC ENAMEL PAINT OF APPROVED BRAND AND SHADE OVER ONE COAT OF RED OXIDE PRIMER COAT (TOTAL 3 COATS) INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, ALL INCIDENTAL, OPERATIONAL & LABOUR CHARGES FOR PREPARING AND CLEANING THE SURFACE OF DIRT WITH SOAP AND BRUSHES, INCLUDING PUTTY, ETC., COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO.1201, 1207, 1212).

SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.S. FLATS OF ALL SIZES

SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.S. SQUARE BARS OF ALL SIZES

PROVIDING ROOFING WITH 0.50 MM THICK GALVANIZED / PRE-PAINTED G.I PROFILED SHEETS FIXED TO THE PURLINS WITH 14 SIZE SELF DRILLING SCREWS WITH NEOPRENE WASHER. SIDE LAPS ARE STICHED WITH SELF TAPPING / DRILLING SCREWS. END LAPS ARE TO BE SEALED WITH 25 X 3 MM BUTYL TAPE. THE SHEETS ARE PROVIDED WITH ANTI CAPILLARY GROVE INCLUDING ALL INCIDENTAL & OPERATIONAL CHARGES COST AND CONVEYANCE OF ALL MATERIALS TO SITE ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLY AND LAYING OF ASHIRVAD / AJAY / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENT OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRWAD FLOWGUARD SDR 13.5 PIPES ARE MADE FROM IDENTICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) - 22.20 MM OD PIPES SDR 13.5

SUPPLY AND LAYING OF ASHIRVAD / AJAY / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENT OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRWAD FLOWGUARD SDR 13.5 PIPES ARE MADE FROM IDENTICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) - 28.60 MM OD PIPES SDR 13.5

SUPPLYING AND FIXING 15 MM DIA BIB TAP WITH FLANGE CHROMIUM PLATED JAQUAR MAKE QUEEN SERIES INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 76.2 MM (3") DIA UV RESISTANT UPVC SWR NAHANI TRAP WITH JALI OF APPROVED ISI BRAND INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND LAYING 110 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND JOINTED WITH SOLVENT CEMENT INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

Supply and Fixing of RO Plant machinary: 2000 liters PVC Tank, CRI Monoblock Pump 1.0 HP, Pressure Sand Filter with Media loading, Multiport Valve & Fittings, Activated Carbon Filter with Media loading, Multiport Valve & Fittings, 20” Micron filters with Housing, Antiscalent Chemical Dosing Pump with Solution Tank, RO Plant SS Skid – 1Nos, 8040 Membrane with Housing - 1Nos, LP & HP Pressure Switches – 1Set, 1.0 HP High Pressure Pump - CRI, Pressure Guages – 1Set, 1 Meter UV Lamp – 1Nos, 2000 Liters SS 304 Storage Tank – 1Nos, PLC Based RO Control Panel – 1Nos, CPVC Pipes & Fittings – 1LOT, Electrical Cables – 1LOT , Auto – Cut off Float Switch – 1Nos , Erection & Commission Charges – 1Lot, Antiscalent Chemical – 5Liters including all incidental, operational, labour charges for finished item of work.

Supply and Fixing of 20mm outer dia (2.20 mm thickness) heavy grade with IS:9537 part 3 FRLS regid surface P.V.C. pipe (ISI MARK) with all accessories fixing on chromium plated metallic base saddles including all labour charges etc., complete for run of mains.Makes :(Makes: Precision/Universal& Marudhar/VIP / Sudhakar).

Supply and Fixing of 25mm outer dia heavy (2.20mm thickness) grade with IS:9537 part 3 regid PVC pipe (ISI mark) of makes concealed in wall with all required accessories including masonary work and labour charges etc., complete. (For circuit mains, power sockets and computer boards only) (Makes: Sudhakar/VIP/GM

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant low smoke FRLS / HFFR PVC insulated 1100V grade as perIS:694/1990 specification flexible copper cable in existing pipe with 6A one way modular switch with 6 modular cover frame, 3 plate Ceiling rose including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non Residential Buildings. Wire Make: (Finolex/RR kabel/Havells/ FortuneArrt) Ceiling rose: Anchor/ Gold Medal Olive /Million Zoom. Switches & Cover frame Make: Legrand (Myrius/Lyncus) / Schneider (Clipsal X/ Livia AB)/ Crabtree (Murano/ Athena) / Lauritz Knudsen - englaze ( Formerly L&T) / Honeywell (Blenzero)

Supply and Fixing of 16/20A 2 Modular 1 way Socket - 2NOs with shutter and 16A / 20A 1 Way Modular Switch-2NOs duly recessed in wall 6 modular cover frame including earth connections and all labour charges etc., complete. Switches & Cover Frame Makes: Legrand Arteor / Schneider Zen celo/ Crabtree Murano or Ducor /L&T-englaze/ GM-(Four-Five)/ Goldmedal(GIFA)

Supply and run of 3 of 36 /0.3mm (2.5 Sq.mm) FRLS / HFFR/ZHFR P.V.C. insulated 1100V grade as perIS:694/1990 specification for insulated flexible copper cable in existing pipe for run of circuits, power plugs & computer boards including all labour charges etc., complete. ( For Phase Neutral and Earth) ( Circuit Mains to Switch Board) Make:Finolex/RR kabel/Havells / FortuneArrt

Supply and run of 3 of 56/0.3mm (4 Sq.mm) FRLS / HFFR/ZHFR PVC insulated 1100V grade as perIS:694/1990 specification for copper cable in existing pipe for mains inlcuding all labour charges etc., complete.( For Phase Neutral and Earth) [from Distribution board mains to16A Sockets]. Make:Finolex/RR kabel/Havells / Fortune Art

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded alluminium housing and polycarbonate cover, input voltage AC 220 - 260 Volts with PF>0.9, Surge protection: 2KV,THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, .etc., complete. Makes: Phillips / GE / Crompton.

Supply and fixing of 12W LED Slim Panel Round /Square suitable for Recessed / Surface mounting made of diecast alluminium body with powder coating, acrylic diffuser with Driver as per IS: 15885 (Part 2/ Sec 13) : 2012 , operating voltaGE-Venture ranGE-Venture of 150 to 265 Volts AC, P.F > 0.9, SurGE-Venture protection: 2KV,THD<10%, with high power LED's having efficacy of > 120 lumins/watt,CCT: 3000K - 5700K, minimum CRI>70, .etc., complete MAKE : Phillips / GE-Venture / Crompton / Wipro / Bajaj

Supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges with 7W LED, 490Lumens bulb (for new installation). Holder Make: Anchor / Gold Medal Olive / Million Zoom LAMP Make:Phillips / OSRAM / GE / Crompton.

Supply and fixing 6way TPN D.B with board with IP-43 protection suitable for three phase40A FP MCB/ Isolator/ RCCB / ELCB - 1 No for incomer, 10kA-6-32A SP MCBs - 12Nos for outgoing. including internal connection and labour charges for surface / flush mounting etc., complete.(for PDB)Make: Legrand(Ekinox 3) / Schneider-A9 / Seimens / Lauritz Knudsen ( Formerly L&T)- Newrange. MCB Make: Legrand- DX3/ Scneider - A9/ Siemens - 5SX4 / Lauritz Knudsen ( Formerly L&T)- AU.

Supply of 25 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) Makes: Universal / CCI / Unicab/Polycab

Supply and transportation of 20W LED Street light Luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass, Supply Input voltage 120 - 270 V AC, P.F > 0.90, high power LED's having System efficacy > 100 lm/W and junction temprature < 70°C, with Ingrees protection IP66, Luminaire performance complies to IS 10322 (Part 5 / Sec-3), Driver surge protection 4KV, external Surge protection 10 KV with optics distribution , THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete. a) LUMINAIRE MAKE : Wipro(Skyline) / Philips (Green line) /GE-Venture / Crompton(Neo Series) / Bajaj (Edge) /Halonix(Lumos - Super) / Havells(EnduraSeries)/Capart(Premium)/Greenlites(Hi-Lux) /Polycab/Keselec/HPL(City Vision)/ Jaquar(Premium)/Eveready/ Surya (Pollux) / FortuneArrt (Leaf)b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA /OSRAM / SAMSUNG / LG.

Fixing of LED street light luminary with 1.0 Mtr., 25mm dia GI pipe bracket and anti tilting MS flat etc., including giving connections and labour charges etc., complete.