Construction of boiling room at mules line drain at cook house and provision of false ceiling rolling shutters geysers exhaust fans and lightning conductors in certain buildings at charri camp under mil stn Dharamshala

Amount

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5 m in depth and getting in any type of soil out complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-10, type C-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete , including necessary formwork where required complete all as specified and directed by the Engr-in-Charge.

Walling of random rubble stone masonry, uncoursed, brought upto courses, well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-15, type B-1 (using 20 mm graded crushed stone aggregate) as in surface channel and drain, complete all as specified and directed by Engr-In-Charge.

Plain cement concrete, M-15, nominal mix, type B-1, (using 20mm graded crushed stone aggregates), as in coping, bed plates, water trough and the like including weathering, slightly, rounded or chamfered angles and throating, complete all as specified and directed by the Engr-in-Charge.

15mm thick rendering in CM 1:4 on stone surface or other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

Extra over stone walling for hammer dressing to face stone and dressing of face beds and joints as specified of random rubble walling uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface not excluding 20mm for granite or trap stone,complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling,watering and well ramming in layers n.exc 25 cm thick ,complete all as specified & directed by Engr-in-Charge.

Removal of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above starting point,complete all as specified & directed by Engr-in-Charge.

False Ceiling using anodised aluminium tee or angle Section snap grid frame work of size 605x 605mm including hangers 6mm dia (upto 1200mm length) adjusting level to roof slab by means of ceiling cleats made out of GI flat 40x3mm size, 60mm long complete and expansion hld fasteners12.5mm dia, 40mm long including 4mm thick asbestos fiber cement bldg board ISI marked e-board colour and designed complete all as specified and directed by Engr-in-Charge.

Steel rolling shutter 1.25mm thick, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one coat of primer errected in position as indicated complete ; gear operated type with bevel gear box and crank handle, complete all as specified and directed by Engr-in-charge.

Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6, complete all as specified and directed by Engr-in-Charge.

Chequered cement concrete tiles maching pressed glossy finished (heavy duty) of size 300x300x30mm thick with grey cement and pigment set jointed & pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6 complete, all as specified and directed by Engr-in-Charge.

Plain Cement concrete, 25mm thick, M-15, type B-1(using 20mm graded crushed stone aggregates) as in floor to receive floor finishes complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick in cm 1:4 on stone masonry surface, finished even and smooth without using extra cement complete, all as specified and directed by Engr-in- Charge.

Rendering 15mm thick in cm 1:6 on stone masonry surface, finished even and smooth without using extra cement complete, all as specified and directed by Engr-in- Charge.

Prepration of Plastered or unplastered surface and applying two coats of all weather exterior paint over a coat of primer on walls complete all as spcified and directed by Engr-in-Charge.

Preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of chalk whitening complete, all as specified and directed by Engr-in-Charge.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

Pre-painted galvalume aluminium Zinc coating GI based corrugated steel sheeting 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

Pre-painted galvalume aluminium Zinc coating GI based plain steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and directed by Engr-in- Charge.

Mild steel work as in wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

Plain Cement Concrete, M-10, 75mm thick type C-2, (using 40mm graded crushed stone aggregates ) as in plinth protection complete all as specified and directed by Engr-in-Charge.

Galvanised iron pipe, medium grade, 15mm bore, ISI marked with screwed socket joints together with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, lugs and union etc., fixed in wall surface/ roof/ on support/laid in trenches complete all as specified and directed by Engr-in-charge.

Glazed ceramic coloured tiles of size 450mmx350mm,thickness not less than 7mm thick as in vertical concrete /brick surfaces, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in- Charge.

Non skid (mat finish) ceramic coloured tiles Primium class-I grade, 7 to 8mm thick (square/rectangular), area of each tiles exc.0.06 sqm but n.exc 0.11 sqm in floors,set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Sink made out of stainless steel 1mm thick (in replacement) for kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf including fixing cantilever brackets and connecting union to pipe over all size 495mm x 420mm bowl size 410mm x300mm x 160mm including 40mm size CP waste coupling & PVC waste pipe complete all as specified and directed by Engr-in-Charge.

2nd Class hard wood plain solid chowkats and frame wrought, framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed by the Engineer-in-Charge.

2nd Class hard wood (Sal/Hallock), Plain framed, panelled 35mm thick shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, Complete all as specified and as directed by the Engineer-in-Charge.

Butt hinges of size 100mm, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in-charge.

150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete, all as specified and directed by Engr-in-Charge.

150mm long aluminium handles, cast type, anodised complete all as specified and directed by Engr-in-Charge.

300mm long, mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of pink primer on new wood or wooden based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed by Engr-in-Charge.

Rolled MS wk as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe-410W (Gde E-250) quality 'A', complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5 m in depth and getting in any type of soil out complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreding, leveling, watering & well ramming in layers not exceeding 25cm thick completed all as specified and directed by Engr-in-Charge.

Removing of excavated soils to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.50mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Plain Cement Concrete, M-15, 40mm thick type B-1, (using 20mm graded crushed stone aggregates ) as in floor finished even & smooth without using extra cement complete all as specified and directed by Engr-in- Charge.

Plain cement concrete, M-7.5, type D-2 (using 40 mm graded crushed stone aggregates) as in sub base and other similar works complete all as specified and directed by the Engr-in-Charge.

Hard Core of gauge 63mm, deposited, spread and levelled in layers not execeeding 15cm thick, watered and rammed to a true surfaces with broken stones, complete all as specified and directed by Engr-in-Charge.

Point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed FRLS electric cable 1100 volts cable and including PVC conduit of 20mm dia (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly in existing CI/wooden box or including wooden/CI box (as per requirement at site) covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point/ fan/exhaust fan point/ bell point etc controlled by one, one way switch,complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Electric wiring shall be done in proper color coding i.e. red for phase, black for neutral & green for earth.. (ii) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost.

All as per item No 42 here-in-above, but for one 3 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 42 here-in-above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 42 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 Amp and 15 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Switch piano, flush type, single pole, one way,15Amp, complete all as specified and as directed by the Engineer-in-Charge. Make: Plaza /SSK/Cona/Havells

Switch piano, flush button, 5 Amp, complete all as specified and as directed by the Engineer-in-Charge. Make: Plaza /SSK/Cona/Havells

Ceiling rose, surface type, 65 mm x 50 mm, two to three terminals/ PVC/ polycarbonate, isolated body fixed on PVC block, complete all as specified and as directed by the Engineer-in-Charge.

Sheet metal enclosure distribution Boards suitable for MCBs of single pole and neutral 4 way double door type with 200 amp rated bus bar complete all specified and as directed by the Engineer-in-Charge. Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing surface. Make: Havells/Legrand/ABB

MCB SPN, 40Amps , 240 volt complete, all specified and as directed by the Engineer-in-Charge.

MCB SP 6 to 32 Amp , 240 volt complete, all specified and as directed by the Engineer-in-Charge.

Energy efficient LED integrated batten, suitable for indoor applications tube light fitting 1x18 Watt 4 FT complete, Trim LED NEO including all fixing arrangement complete, all as specified and as directed by the Engr-in-Charage. Make: Havells Cat Part No LUMILINERS 18WLED 865SPCWH or equivalent in Philips/Bajaj.

LED street light fitting 1x25 watt with lamp pressure die cast housing with epoxy powder coated dark graphite grey colour finish, prismatic polycarbonate cover with individual LED lenses with bracket of made of GI pipe 1.5 mtr length,bent to the shape including necessary clamps, nuts bolts etc; complete all as specified and as directed by the Engr-in-Charage. Make Crompton Cat Part No LSTS 25-CDL- LED or equivalent in Philips/Syska/CG

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40x40x6mm and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate complete all as specified and shown in EP-3 of SSR Part-I & as directed by Engr-in-Charge.

1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 01 metre apart including 4mm suspension wire, one twin core cable flat or circular stranded conductor size of 10 Sqmm, 2 core complete all specified and as directed by the Engineer-in-Charge.

House service bracket (hook type) complete with 3.0m long G.I. pipe 40mm dia medium grade two nos 90 degree bends M.S. hook etc complete all specified and as directed by the Engineer-in-Charge.

Air termination single pointed aluminium rod 12mm dia and 300mm long including supporting pipe 15mm bore & PCC M-15 as required at site compelete all as specified & directed by Engr-in-Charge.

Aluminium strip 25x3.15mm with saddles and fixing screws etc for roof conductor above ground compelete all as specified & directed by Engr-in-Charge.

Galvanised iron strip 32x6 mm and fixing screws buried in ground or above ground/Wall for test point compelete all as specified & directed by Engr-in-Charge.

Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexa head screw compelete all as specified & directed by Engr-in-Charge.

Geyser (water heater storage type), electrical, capacity 35 litres. BEE 5 star rated, vertical type including giving inlet & outlet connections, testing, commissioning complete all as specified and as directed by the Engineer-in-Charge. Make: Jaquar/ Racold/ Venus. Note : Fixing of electric geyser on wall with suitable size of Anchor bolt including grouting in PCC, making good the disturbed surface shall be part of the job at no extra cost.

PVC bib tap standard of PTMT any color high pressure screwed for uiron pipe and fixed 15mm dia GI pipe complete all as specified and directed by Engr-in-charge.

15mm bore, stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions complete all as specified and directed by Engr-in-Charge.

Cutting, screwing alterations and additions in existing GI pipe of size 15mm dia including clamps, screws etc complete all as specified and directed by Engr-in-charg. The disturbed surfaces will be made as per existing surfaces.

Exhaust fan, single phase, 1400 RPM, 300 mm sweep, heavy duty with louver ( Iron shutter) and connecting with electrical system, including provision of cable copper flexible, PVC three core 23/0.0076 from ceiling rose to fan and grounting of and including holding down bolts of suitable size in and including PCC M-15 (Nominal Mix) using 20 mm crushed stone aggregate blocks & plaster work complete all a specified and directed by Engr-in-Charge. Make: Havells/Crompton Greaves/Bajaj/Phillips

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 2.5 mtr below the normal ground level connected to galvanised earth strip 32x6mm thick by means of nuts bolts, washers, check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) medium grade GI watering pipe 20mm dia with funnel and wire mesh and 40mm bore GI pipe light grade protection pipe up to test point etc including excavation and charcoal, common salt surrounded with 15cm all around the plate completion all as specified and directed by the Engineer-in-Charge.

M/s Thakur Engineers