KIIFB- Augmentation of WSS to Kollam corporation - Construction of Transformer Building and allied works, Supply erection of Raw and Clear water pumpsets, Construction of Electrical Substations, Automation Scada, CCTV Solar panel installation

Amount

PART I - ELECTRIFICATION - RAW WATER PUMPING STATION

OD247904/2022-2023:HT PANELS:- Supply, conveyance, installation, testing and commissioning of 11 kV, 7 breaker panel consisting of one incomer and 6 outgoings. The panel shall be complete with appropriately rated VCBs, protective relays, meters, control switches, indication lamps, CTs, PTs and all other equipments as per SLD, BoM for panels and detailed technical specifications. A metering panel with all required CTs, PTS, meters and other accessories which satisfies the requirement of KSEB and as per SLD, BoM for panels and detailed technical specifications shall also be integrated with this panel

OD248375/2022-2023:TRANSFORMER:- Supply, conveyance, installation, testing and commissioning of 63 kVA, 11 kV/433V, cast resin outdoor transformer conforming to the latest Standards and in conformity with the detailed technical specifications attached

OD113952/2023-2024:3.30 kV VFD:-Supply, conveyance, installation, testing and commissioning of low harmonic VFD in compliance with IEEE 519 mitigation level suitable for 750 kW based on the latest multicell technology with integrated 11 kV/ 3.3 kV copper wound transformer of adequate rating. The VFD shall conform the specification exlained in the detailed tender specification and conform to the latest Standards

OD113951/2023-2024:3.30 kV VFD:- Charges for witnessing the at site factory acceptance tests (FAT) which shall be conducted inside the respective VFD manufacturer's factory

OD248390/2022-2023:PANEL BOARDS:- SITC of MSB for common loads - (415V system) as per detailed technical specifications and detailed in A1 of BoM for Panels.

OD248389/2022-2023:PANEL BOARDS:- SITC of VC Panel 1 - (415V system) as per detailed technical specifications and detailed in A2 of BoM for Panels.

OD113953/2023-2024:PANEL BOARDS:- Supply and fixing emergency stop button with key in IP 65 thermoplastic enclosure, made of high quality polycarbonate PC - GFS (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, self extinguishing having high impact resistance against mechanical load made of halogen and silicon fee recyclable material conforming to RoHS directive 2002/95/EC, UV resistant, having high gradev internally embedded gasket made of polyurethane(PUR). For better safety, enclosure should withstand glow wire test at 96?C in accordanace with IEC 60 695-2-11 UL subject 94, should be flame retardant andvself-extinguishing in nature. Size 93x93x123 mm

OD113955/2023-2024:PANEL BOARDS:- Supply and providing break glass type emergency push button with chain and hammer

OD248415/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2/4 way, Single door (for mounting Isolator/ MCB/ RCCB etc)

OD249023/2022-2023:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

OD249028/2022-2023:Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

OD249038/2022-2023:Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

OD249080/2022-2023:Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

OD249126/2022-2023:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

OD249139/2022-2023:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Tripple pole

OD249160/2022-2023: Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

OD249199/2022-2023:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

OD249217/2022-2023:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

OD249229/2022-2023:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

OD249257/2022-2023:Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

OD249351/2022-2023:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

OD249806/2022-2023:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Up to 35 sq mm

OD249827/2022-2023:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 35 sq mm and up to 95 sq mm

OD249835/2022-2023:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Up to 35 sq. mm (clamped with 1mm thick saddle)

OD250804/2022-2023: Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp)

OD250807/2022-2023:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp)

OD250810/2022-2023:Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) amended up to date: 3.50 x 70 sq.mm (A2XFY/A2XWY)

OD250811/2022-2023:Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) amended up to date: 3.50 x 25 sq.mm (A2XFY/A2XWY)

OD250815/2022-2023:Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) amended up to date: 4 x 10 sq.mm (A2XFY/A2XWY)

OD250822/2022-2023:Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) amended up to date: 3 x 4 sq.mm(A2XFY/A2XWY)

OD250848/2022-2023:Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) amended up to date: 2 x 4 sq.mm (A2XFY/A2XWY)

OD250854/2022-2023:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 3.30 kV/ 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and up to 400 sq. mm

OD113959/2023-2024:CABLING:-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 3.30 kV/ 11KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 120 sq. mm and up to 400 sq. mm

OD113958/2023-2024:CABLING:-Laying and clamping of one number PVC insulated and PVC sheathed / XLPE power cable of 3.30 kV/ 11KV grade of following size on wall / cable tray using clamps fabricated from 40 x3 mm MS flat. Above 120 sq. mm and up to 400 sq. mm

OD251341/2022-2023:Supply of the following size 3.3 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 2) amended up to date: 3 x 185 sq.mm (A2XFY/A2XWY)

OD251342/2022-2023:CABLING:-Supply of the following size 11 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 2) amended up to date: 3 x 150 sq.mm (A2XFY /A2XWY)

OD251343/2022-2023:CABLING:-Supply of the following size 11 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 2) amended up to date: 3 x 300 sq.mm (A2XFY/A2XWY)

OD251344/2022-2023:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 2x1.50 sq.mm (2XFY/2XWY)

OD251345/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 4 x1.50 sq.mm(2XFY/2XWY)

OD251347/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 8 x1.50 sq.mm(2XFY/2XWY)

OD251348/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 12 x1.50 sq.mm (2XFY/2XWY)

OD251685/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 2 x2.50 sq.mm(2XFY/2XWY)

OD251688/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 4 x 2.50 sq.mm

OD251695/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 8 x2.50 sq.mm

OD251699/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 12 x2.50 sq.mm

OD251718/2022-2023:CABLING:-Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

OD251721/2022-2023:CABLING:- Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 2 X 1.50 sq. mm / 2 x 2.50 sq mm

OD251728/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 4 X 1.50 sq. mm / 4 x 2.50 sq mm

OD251796/2022-2023:CABLING:- Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 8 X 1.50 sq. mm / 8 x 2.50 sq mm

OD251799/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 12 X 1.50 sq. mm / 12 x 2.50 sq mm

OD251822/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 4 sq mm/ 3 x 4 sq mm

OD251830/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4x10 sq mm

OD251838/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

OD251920/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)

OD251921/2022-2023:CABLING:-supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 3.3 KV grade as required 3 x 185 sq mm

OD251925/2022-2023:CABLING:-supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 3 x 150 sq mm

OD251926/2022-2023:CABLING:- supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 3 x 300 sq mm

OD251928/2022-2023:CABLING:-supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 3 x 300 sq mm

OD251935/2022-2023:CABLING:-Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (100 cm deep)and re-filling etc as required/ duly clamped 150 mm dia

OD251937/2022-2023:CABLING:-Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

OD251940/2022-2023:CABLING:-Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)

OD251942/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

OD251944/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

OD251945/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 225 mm width X 50 mm depth X 1.6 mm thickness

OD251946/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

OD251948/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

OD252110/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 600 mm width X 50 mm depth X 2.0 mm thickness

OD252124/2022-2023:CABLING:-Supplying and installation including all manner of supports/ suspenders, anchor bolts etc. for cable trays made out of suitable size channel sections, slotted angles, flats, MS plates etc. as required including painting with 2 coats of synthetic enamel pain

OD252128/2022-2023:CABLING:-Supply and installation of supports for panel boards made out of suitable size channel sections etc. as required including cutting, welding, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc. as required.

OD252145/2022-2023:CABLING:-Supply and providing MS chequered plate of suitable thickness including cutting, welding, painting etc. as required for the cable trench covering.

OD252150/2022-2023:CABLING:-Sealing the ends of pipes and cable entry points of ducts using expanding chemicals foam as explained in the detailed technical specification.

OD252172/2022-2023:INTERNAL ELECTRIFICATION:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

OD252173/2022-2023:INTERNAL ELECTRIFICATION:-Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

OD252178/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 2.5 sq. mm

OD252229/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 4 sq. mm

OD252231/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 4 x 4 sq. mm

OD252244/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 6 sq. mm

OD252267/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 4 x 6 sq. mm

OD252270/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

OD252273/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

OD252275/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

OD252290/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

OD252298/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm)

OD252299/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm)

OD252301/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

OD252310/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

OD252313/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

OD252315/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet

OD252317/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

OD252318/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing brass batten/ angle holder including connection etc. as required including 7 W LED lamp and 200 mm Alu polished shade

OD252321/2022-2023: INTERNAL ELECTRIFICATION:-Supply, conveyance installation testing and commissioning the light fittings of following types made of round block CRCA with 0.5mm thickness complete with all accessories and lamps etc. directly on wall or ceiling with PVC round block neatly painted to suit the fitting and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.1200 mm 1X20W LED Lamp with box type fixture

OD253452/2022-2023:INTERNAL ELECTRIFICATION:-Supply, fabrication, conveyance and fixing the following sizes of B class GI pipe bent to shape / cut and welded to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required.32 mm dia with HG company fabricated clamps

OD253453/2022-2023:INTERNAL ELECTRIFICATION:-Supply Conveyance, installation, testing and commissioning of 36/40 W LED street light output greater than 105 lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/ Lumilled/ Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79 & 80 certificates from NABL accredited third party lab to be produced mentioning chip manufacturer) (DuroLed Pro Well glass BY202PLED43SCW PSU PC of M/s Signify or equivalent)

OD253476/2022-2023:INTERNAL ELECTRIFICATION:-Supply Conveyance, installation, testing and commissioning of 35 W LED medium bay fitting with output greater than 120 lumen/W 4000-6000 K with IP 66/ IK 8 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.90 at full load, internal surge protection up to 4 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD Less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79&80 certificates from NABL accredited third party lab to be produced mentioning chip manufacturer) (Substation building) To be suspended from ceiling by suitable metallic chain/ bouden and giving connection using 16/0.20 mm 3 core PVC/PVC round flex wire (BY202P LED 435 CW PSU PC SPD of M/s Signify or equivalent)

OD253477/2022-2023:INTERNAL ELECTRIFICATION:-Supply Conveyance, installation, testing and commissioning of 200 W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer) (pump house)

OD253485/2022-2023:INTERNAL ELECTRIFICATION:-Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

OD253486/2022-2023:INTERNAL ELECTRIFICATION:-Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

OD253487/2022-2023:INTERNAL ELECTRIFICATION:-Supply, conveyance, installation, testing and commissioning of light duty exhaust fans with metal body and metal blades with self opening louvers of the following sizes using standard accessories and giving connection with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire working on 230V/240V single phase A/C supply 225 mm sweep or nearest available size including cutting necessary holes, finishing the holes etc. as required

OD253488/2022-2023:INTERNAL ELECTRIFICATION:-Supply, conveyance, installation, testing and commissioning of heavy duty exhaust fans with metal body and metal blades of the following sizes using standard accessories and giving connection with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire working on 230V/240V single phase A/C supply 450 mm sweep or nearest available size including cutting necessary holes, finishing the holes etc. as required

OD253489/2022-2023:INTERNAL ELECTRIFICATION:-Supply, installation, testing and commissioning of 7 m height octagonal pole made out of hot dip galvanised GI sheet 70 mm top diameter, 130 mm bottom diameter, thickness 3 mm, base plate dimensions of 200 x 200 x 12 mm suitable for wind speed as per IS 875 Part 3, single arm bracket 0.50 m including connector, foundation bolts 4 nos. fixed in existing RCC foundation and junction box etc including excavation (50x50x180 cm), 1:3:6 RCC (40x40x220 cm), 3x1.50 sq. mm Cu wire from control box to lamp terminals,, providing necessary controls etc as required.

OD253490/2022-2023:INTERNAL ELECTRIFICATION:-Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 2.00 mm copper conductor ( 14 SWG)

OD253491/2022-2023:INTERNAL ELECTRIFICATION:-Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 3.15 mm copper conductor ( 10 SWG)

OD253492/2022-2023:INTERNAL ELECTRIFICATION:-Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.00 mm (14 SWG)

OD253497/2022-2023:INTERNAL ELECTRIFICATION:-Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required. 3.15 mm (10 SWG)

OD253498/2022-2023:INTERNAL ELECTRIFICATION:-Earthing with GI earth plate 1200 x 1200 x 12 mm thick including accessories and providing masonry enclosure with RCC slab covering, watering pipe, funnel with mesh, required quantity of charcoal/ coke, salt etc as per IS 3043: 2018 as required

OD253499/2022-2023:INTERNAL ELECTRIFICATION:-Supply and laying 32 x 3 mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required

OD253500/2022-2023:INTERNAL ELECTRIFICATION:-Supply and laying 25 x 3 mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required

OD253501/2022-2023:INTERNAL ELECTRIFICATION:-SITC of 5 kVA UPS with single phase input and single phase output with 30 min backup in conformity with the detailed technical specifications attached

OD253502/2022-2023:INTERNAL ELECTRIFICATION:-Supply and wiring plug points in combined position in the same system explained as item No.1

OD253503/2022-2023:INTERNAL ELECTRIFICATION:-Supply and providing 2.50 mm elastomeric fire retardant insulating mat as per IS 15652/2006 to withstand 11 kV dielectric strength including pasting in ground using synthetic adhesive

OD253504/2022-2023:INTERNAL ELECTRIFICATION:-Supply and providing 2 mm elastomeric fire retardant insulating mat as per IS 15652/2006 to withstand 3.3 kV dielectric strength including pasting in ground using synthetic adhesive

OD253505/2022-2023:INTERNAL ELECTRIFICATION:-Supply and providing Fire Extinguisher ABC type 6 Kg with hose and clamp

OD253506/2022-2023:INTERNAL ELECTRIFICATION:-Supply and providing 9 litre capacity GI fire bucket painted using post office red with priming coat of red oxide and written with white paint 'FIRE' mounted on MS angle framework for wall bracket filled with fine sand painting the stan, making good the damages etc. as per IS 2546 Nos. fire bucket with stand including making good the damages , colour washing etc. as required

OD253507/2022-2023:INTERNAL ELECTRIFICATION:-supply and providing First aid chart duly framed with glass and placed in a conspicuous location

OD253508/2022-2023:INTERNAL ELECTRIFICATION:-Supply of 12 kV grade insulated gloves

OD253509/2022-2023:ENERGY MANAGEMENT SYSTEM :- Supply, installation, testing and commissioning of Energy Management System (EMS) as per the attached architecture and as explained in the Detailed Technical Specifications (DTS) consisting of Modbus gateway with Dual Ethernet port to convert RS 485 to Modbus TCP (For RS485 meters), required power supply for gateway and smart link, ISO 50001/50006 certified Power Monitoring software, Web View Software, server/ workstation PC as explained in the DTS, connected Service Plan for performing System analysis and network Analysis -Advisor service connected Prime plan [twice a year] connecting up to 90 credit points, Smark link / Easycom etc as required. The system should support a minimum of the following meters and devices or their equivalent approved makes: ION9000, PM8240, PM5560, PM2230H, PM1130H, EM6400NG, EM6438H, EM7230, MTZ with EIFE, NW with IFE, NSX with IFM/IFE, Smart link Modbus, Power Tag, Heat Tag, Wireless Thermal Sensors, Easergy relays, Panel Server etc. "

OD253513/2022-2023:LIGHTNING PROTECTION:- Providing and fixing Fully Solid Vertical Air terminals for wind stability as per IS/IEC -62305 part-3 For 1,2,3, 4 meter air terminal 16mm rod tapered to 10 mm aluminium rod meter rod: Meets the requirement (IS/IEC 62305) Semi-hard (E-AlMgSiO5) Suitable for high wind load. All air terminal must have Interception Tip at the Top of air terminal. System consist of Fang Fix with base and clamp on the top air terminal is erected. Air terminal Joining Clip Stainless Steel SS 304 clamp made of cable bracket, lightning tested for 100 KA 10/350 micro sec waveform. Stainless Steel Wall Clamp or 16 KG stone of 365 mm diameter, high level of stability. No of stones/wall clamps depending on wind load. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman"

OD253514/2022-2023:LIGHTNING PROTECTION:-"Providing & fixing of 8mm solid aluminium round conductor with necessary holders @ required interval as specified below: Shall meet the requirement of (IS/IEC 62305) : semi-hard (E-AlMgSiO5 )with 50 sq.mm cross sectional area. Govt approved Indian labs test certificate required. Make: Cape / Erico / Furse "

OD253515/2022-2023:LIGHTNING PROTECTION:-Providing and fixing of Cross Connector/T Connector/Folding Clamp/Clamping Shoe/ Expansion Piece: to route vertical down conductor /mesh formation made of Aluminium Ferrule using screw free joints. Folding Clamp/Clamping Shoe for metal panels (up to 20mm thickness of the metal frame): Folding clamp/clamping shoe for metal frame thickness up to 20mm, made of stainless steel SS 304/316 grade , conforms to the requirements according to (IS/IEC 62305). Expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length at every 20 meters horizontally. Using round conductor 8mm aluminium conductor with straight Connector: using Aluminium Ferrule. Quick installation using crimp joints. Conforms to the requirements according to (IS/IEC 62305). Make sure all joints are strong and will be inspected at site. Galvanised Iron joints are not permitted to avoid risk of corrosion. Single bolt joints are not permitted to avoid risk of faulty loose joints and reduce risk of flash over. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

OD253516/2022-2023:LIGHTNING PROTECTION:-Providing and fixing of Stainless Steel Test Joint suitable with suitable Outdoor Enclosure: For 8mm dia solid round aluminium conductor & 10mm dia copper coated solid steel round conductor having 100 microns of copper bonding . Conforms to the requirements according to (IS/IEC 62305).The enclosure should be outdoor glass-fibre reinforced polycarbonate opaque having minimum inner dimension of 75mm x 75 mm x 50 mm. The test link has to be straight and needs minimum 4 mounting screws for strong joints. Inspection of bimetallic corrosion at site required. Separation of 8mm Aluminium & 10mm Copper bonded steel is required for future inspection and contractor has to make sure both conductors should not touch each other to avoid bimetallic corrosion. Single bolt joints are not permitted. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

OD253520/2022-2023:LIGHTNING PROTECTION:-"Providing and laying copper coated steel solid round conductor 10mm diameter from earth electrode directly in ground as required. copper coated steel, high corrosion resistant. Meets the requirement of (IS/IEC 62305) copper coating thickness of 100microns Should be tested and use exclusively for lightning protection earthing system and ring equipotential bonding. After test link needs to be routed inside Heavy duty conduit to avoid touch potential till ground level. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman "

OD253521/2022-2023:LIGHTNING PROTECTION:-Installation of Exothermic Weld Joints for 10mm round copper bonded steel conductor having 100 microns as per IS/IEC 62305. Each under ground joints has to be wrapped with petrolatum- coated chemical fibre fabric having 1.1mm thick and width 50mm. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

OD253522/2022-2023:LIGHTNING PROTECTION:-Providing and fixing of maintenance free Earthing system comprises of molecularly bonded copper of 99.9% purity on low carbon steel of min 3048mm length (10 feet), having a diameter of 20mm with copper bonding thickness of 250 microns as per UL 467. The Rod has to be either continuous or with self-coupling peg & bore arrangement with fault current withstand capability of 30 KA rms value for 1 second and I peak of 76 KA. The rod must be having corrosion test, peel off test for uniform coating, 180 degree bend test with out peel off of copper bonding. Exothermic welded Clamp for clamping as suggested as per NBC 2016. Ordinary Stainless steel/Copper alloy universal clamps are not recommended. For self coupling peg & bore arrangement rod needs Impact point on the bottom rod for easy insertion. Earth enhancing mineral compound is used for improving the soil conductivity. The material shall be mineral inert to sub soil and shall not pollute the environment and non corrosive to earth rod. The material should have a resistivity less than 0.2 Ωm. It should be free from hazardous substances. The mineral compound is required to have minimum 25 Kg of the total composite. The compound should be chemically inert and needs to submit Govt approved Indian labs test certificate. Concrete Earth electrode inspection chamber with weight bearing capacity of 50KN. The dimension shall be 320mmx 190mm. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

PART II - ELECTRIFICATION - WATER TREATMENT PLANT

OD247987/2022-2023:HT PANELS:- Supply, conveyance, installation, tesing and commissioning of 11 kV, 4 breaker panel consisting of one incomer and 3 outgoings. The panel shall be complete with appropriately rated VCBs, potective relays, meters, conrol switches, indication lamps, CTs, PTs and all other equipments as per SLD, BoM for panels and detailed technical specifications. A metering panel with all required CTs, PTS, meters and other accessories which satisfies the requirement of KSEB and as per SLD, BoM for panels and detailed technical specifications shall also be integrated with this panel<br>

OD253724/2022-2023:TRANSFORMER:- Supply, conveyance, installation, testing and commissioning of 1000 kVA, 11 kV/433V, cast resin transformer conforming to the Standards and specifications explained in the detailed technical specifications

OD253734/2022-2023:TRANSFORMER:- Supply, conveyance, installation, testing and commissioning of 400 kVA, 11 kV/433V, cast resin transformer conforming to the Standards and specifications explained in the detailed technical specifications

OD253744/2022-2023:BUSBAR TRUNKING SYSTEM :-Supply Installation Testing and Commissioning of Compact Sandwich Aluminium Busway System with copper contact joints Totally Type Tested in accordance with IEC61439-6, of below mentioned rating 1000V,3Phase 4 Wire, 50Hz with 100% neutral, 50% integral earth without external earth strip, IP54/65, Duel housed in electrogalvanized sheet steel and aluminium enclosure, ANSI 49 Grey epoxy painting and with KEMA-KEUR, ASTA DIAMOND Certification - 1600 A IP 54 feeder unit

OD253756/2022-2023:BUSBAR TRUNKING SYSTEM:- Supply Installation Testing and Commissioning of 1600 A IP 54 flanged end suitable for the feeder unit

OD253762/2022-2023:BUSBAR TRUNKING SYSTEM:- Supply Installation Testing and Commissioning of 1600 A IP 54 90 degree elbow suitable for the feeder unit

OD253764/2022-2023:BUSBAR TRUNKING SYSTEM:- Supply Installation Testing and Commissioning of 1600 A IP 54 copper flexible connection suitable for the feeder unit

OD253787/2022-2023:BUSBAR TRUNKING SYSTEM:- Supply Installation Testing and Commissioning of 1600 A IP 54 adaptor suitable for the feeder unit

OD253788/2022-2023:BUSBAR TRUNKING SYSTEM:- Supply Installation Testing and Commissioning of 1600 A IP 54 edgewise hanger/ ceiling suspender suitable for the system

OD253877/2022-2023:PANEL BOARDS:- SITC of MSB1 (415V system) as per detailed technical specifications and detailed in B1 of BoM for Panels.

OD253876/2022-2023:PANEL BOARDS:- SITC of SB1 - CWPP1 - (415V system) as per detailed technical specifications and detailed in B2 of BoM for Panels.

OD253912/2022-2023:PANEL BOARDS:- SITC of SB2 - CWPP2 (415V system) as per detailed technical specifications and detailed in B3 of BoM for Panels.

OD253911/2022-2023:PANEL BOARDS:- SITC of SB3 - CWPP3 (415V system) as per detailed technical specifications and detailed in B3 of BoM for Panels.

OD253957/2022-2023:PANEL BOARDS:-SITC of SB4 - CWPP4 - (415V system) as per detailed technical specifications and detailed in B4 of BoM for Panels.

OD253874/2022-2023:PANEL BOARDS:- SITC of MSB2 (415V system) as per detailed technical specifications and detailed in B5 of BoM for Panels.

OD253943/2022-2023:PANEL BOARDS:- SITC of MCC VCP (415V system)as per detailed technical specifications and detailed in B6 of BoM for Panels.

OD253873/2022-2023:PANEL BOARDS :- SITC of CW VCP1, CW VCP2 & CWVCP3 (415V system) as per detailed technical specifications and detailed in B6 of BoM for Panels.

OD253872/2022-2023:PANEL BOARDS:- SITC of CW VCP4, (415V system)as per detailed technical specifications and detailed in B8 of BoM for Panels.

OD253956/2022-2023:PANEL BOARDS :- SITC of 125 kVAr APFC panel as per detailed technical specifications and detailed in B10 of BoM for panels (In 7 steps of ratings 50 kVArx1 + 25 kVArx1 + 12.50 kVArx3 + 7.50 kVARx1 + 5 kVAr x 1)

OD253955/2022-2023:PANEL BOARDS :- SITC of 600 A active harmonic filter as per detailed technical specifications and detailed in B11 of BoM for panels

OD253871/2022-2023:PANEL BOARDS :-Supply and fixing emergency stop button with key in IP 65 thermoplastic enclosure, made of high quality polycarbonate PC - GFS (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, self extinguishing having high impact resistance against mechanical load made of halogen and silicon fee recyclable material conforming to RoHS directive 2002/95/EC, UV resistant, having high grade internally embedded gasket made of polyurethane(PUR). For better safety, enclosure should withstand glow wire test at 96ᵒC in accordance with IEC 60 695-2-11 UL subject 94, should be flame retardant and self-extinguishing in nature. Size 93x93x123 mm

OD253870/2022-2023:PANEL BOARDS :-Supply and providing break glass type emergency push button with chain and hammer

OD253978/2022-2023:DISTRIBUTION BOARDS:- Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

OD253980/2022-2023:DISTRIBUTION BOARDS:- Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

OD254000/2022-2023:DISTRIBUTION BOARDS:- Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

OD255132/2022-2023:DISTRIBUTION BOARDS:- Supply and fixing, 2/4 way double door enclosure suitable for mounting 2 pole isolator/ RCBO incomer of sheet steel, dust protected, duly powder painted with tinned copper busbar, common neutral link, earth bar, DIN bar, for mounting MCB including supply and fixing 6 - 32 A, 240V, C Curve DP MCB including giving necessary connections as required

OD255162/2022-2023:DISTRIBUTION BOARDS:- Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

OD255163/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Three pole

OD255170/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

OD255171/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

OD255216/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

OD255264/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

OD255267/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

OD255268/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

OD255271/2022-2023:DISTRIBUTION BOARDS:-Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

OD255275/2022-2023:CABLING:- Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Above 35 sq. mm and up to 95 sq. mm

OD255276/2022-2023:CABLING:-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Above 95 sq. mm and up to 185 sq. m

OD255278/2022-2023:CABLING:-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Above 185 sq. mm and up to 400 sq. mm

OD255315/2022-2023:CABLING:-Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Above 35 sq. mm and up to 95 sq. mm

OD255335/2022-2023:CABLING:-Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Above 95 sq. mm and up to 185 sq. mm

OD255337/2022-2023:CABLING:-Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Above 185 sq. mm and up to 400 sq. mm

OD255339/2022-2023:CABLING:-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 35 sq. mm and up to 95 sq. mm

OD255342/2022-2023:CABLING:-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 95 sq. mm and up to 185 sq. mm

OD255343/2022-2023:CABLING:-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 185 sq. mm and up to 400 sq. mm

OD255344/2022-2023:CABLING:-Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Up to 35 sq. mm (clamped with 1mm thick saddle)

OD255346/2022-2023:CABLING:-Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp)

OD255348/2022-2023:CABLING:-Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 95 sq. mm and up to 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

OD255349/2022-2023:CABLING:-Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 185 sq. mm and up to 400 sq. mm (clamped with 40x3mm MS flat clamp)

OD255356/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 2x1.50 sq.mm

OD255365/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 4 x1.50 sq.mm

OD255367/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 8 x1.50 sq.mm

OD255377/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 12 x1.50 sq.mm

OD255379/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 2 x2.50 sq.mm

OD255382/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 4 x 2.50 sq.mm

OD255384/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 8 x2.50 sq.mm

OD255385/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured copper conductor control cable confirming to IS 7098 (part 1) amended up to date: 12 x2.50 sq.mm

OD255402/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date: 3 x10 sq.mm

OD255405/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date: 3 x70 sq.mm

OD255409/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date: 3 x95 sq.mm

OD255412/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date: 3 x300 sq.mm

OD255415/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date:3.5x95 sq.mm

OD255418/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date:3.5x120 sq.mm

OD255423/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date:3.5x240 sq.mm

OD255424/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date:3.5x300 sq.mm

OD255425/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date:3.5x400 sq.mm

OD255427/2022-2023:CABLING:-Supply of the following size 1.1 kV grade XLPE insulated PVC sheathed, armoured aluminium conductor cable confirming to IS 7098 (part 1) amended up to date: 4 x10 sq.mm

OD255436/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 2 X 1.50 sq. mm / 2 x 2.50 sq mm

OD255444/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 4 X 1.50 sq. mm / 4 x 2.50 sq mm

OD255458/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 8 X 1.50 sq. mm / 8 x 2.50 sq mm

OD255465/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor control cable of 1.1 KV grade as required. 12 X 1.50 sq. mm / 12 x 2.50 sq mm

OD255480/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3 x 10 sq mm

OD255483/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3 x 70 sq mm

OD255486/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3 x 85 sq mm

OD255492/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3 x 300 sq mm

OD255493/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3.5 x 95 sq mm

OD255495/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3.5 x120 sq mm

OD255498/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3.5 x240 sq mm

OD255509/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3.5 x300 sq mm

OD255519/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 3.5 x400 sq mm

OD255547/2022-2023:CABLING:-Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor control cable of 1.1 KV grade as required. 4 x 10 sq mm

OD255562/2022-2023:CABLING:-Supply of the following size 11 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 2) amended up to date: 3 x 150 sq.mm

OD255566/2022-2023:CABLING:-Supply of the following size 11 kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 2) amended up to date: 3 x 300 sq.mm

OD255569/2022-2023:CABLING:-supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 3 x 150 sq mm

OD255570/2022-2023:CABLING:-supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 3 x 300 sq mm

OD255573/2022-2023:CABLING:-supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 3 x 300 sq mm

OD255608/2022-2023:CABLING:-Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (100 cm deep)and re-filling etc as required/ duly clamped 150 mm dia

OD255613/2022-2023:CABLING:-Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

OD255616/2022-2023:CABLING:-Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)

OD255625/2022-2023:CABLING:-Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 160 mm dia (OD-160 mm & ID-135 mm nominal)

OD255629/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

OD255661/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

OD256124/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 225 mm width X 50 mm depth X 1.6 mm thickness

OD256155/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

OD256157/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

OD256159/2022-2023:CABLING:-Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 600 mm width X 50 mm depth X 2.0 mm thickness

OD256176/2022-2023:CABLING:-Supplying and installation including all manner of supports/ suspenders, anchor bolts etc. for cable trays made out of suitable size channel sections, slotted angles, flats, MS plates etc. as required including painting with 2 coats of synthetic enamel pain

OD256918/2022-2023:CABLING:-Supply and installation of supports for panel boards made out of suitable size channel sections etc. as required including cutting, welding, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc. as required.

OD256923/2022-2023:CABLING:-Supply and providing MS chequered plate of suitable thickness including cutting, welding, painting etc. as required for the cable trench covering.

OD256925/2022-2023:CABLING:-Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

OD256927/2022-2023:CABLING:-Sealing the ends of pipes and cable entry points of ducts using expanding chemicals foam as explained in the detailed technical specification.

OD256931/2022-2023:EARTHING & EARTH LEADS :- Earthing with GI earth plate 1200 x 1200 x 12 mm thick including accessories and providing masonry enclosure with RCC slab covering, watering pipe, funnel with mesh, required quantity of charcoal / coke, salt etc. as per IS 3043:2018 as required.

OD256934/2022-2023:EARTHING & EARTH LEADS :-Supply and laying 40 x 6mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required.

OD256936/2022-2023:EARTHING & EARTH LEADS :-Supply and laying 32 x 6mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required.

OD256937/2022-2023:EARTHING & EARTH LEADS :-Supply and laying 32 x 3mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required.

OD257530/2022-2023:EARTHING & EARTH LEADS :-Supply and laying 25 x 6 mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required.

OD257536/2022-2023:EARTHING & EARTH LEADS :-Supply and laying 25 x 3 mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required.

OD257540/2022-2023:EARTHING & EARTH LEADS :-Supply and drawing bare earthing conductors of the following sizes along with wiring/cables and giving connection as required 2.00 mm copper conductor (14 SWG)

OD257543/2022-2023:EARTHING & EARTH LEADS :-Supply and drawing bare earthing conductors of the following sizes along with wiring/cables and giving connection as required 3.15 mm copper conductor (10 SWG)

OD257544/2022-2023:EARTHING & EARTH LEADS :-Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required . 2.00 mm (No.14 SWG)

OD257548/2022-2023:EARTHING & EARTH LEADS :-Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required . 3.15 mm (No.10 SWG)

OD257672/2022-2023:INTERNAL ELECTRIFICATION:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

OD257703/2022-2023:INTERNAL ELECTRIFICATION:-Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

OD257721/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 2.5 sq. mm

OD257720/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 4 sq. mm

OD257719/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 4 x 4 sq. mm

OD257718/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 6 sq. mm

OD257717/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 4 x 6 sq. mm

OD257716/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

OD257715/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

OD257714/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

OD257713/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

OD257855/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm)

OD257856/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm)

OD257858/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

OD257859/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

OD257860/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

OD257861/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet

OD257863/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

OD257864/2022-2023:INTERNAL ELECTRIFICATION:-Supplying and fixing brass batten/ angle holder including connection etc. as required including 7 W LED lamp and 200 mm Alu polished shade

OD257865/2022-2023:INTERNAL ELECTRIFICATION:- Supply, conveyance installation testing and commissioning the light fittings of following types made of round block CRCA with 0.5mm thickness complete with all accessories and lamps etc. directly on wall or ceiling with PVC round block neatly painted to suit the fitting and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.1200 mm 1X20W LED Lamp with box type fixture

OD257867/2022-2023:INTERNAL ELECTRIFICATION:-Supply, fabrication, conveyance and fixing the following sizes of B class GI pipe bent to shape / cut and welded to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required.32 mm dia with HG company fabricated clamps

OD257869/2022-2023:INTERNAL ELECTRIFICATION:-Supply Conveyance, installation, testing and commissioning of 36/40 W LED street light output greater than 105 lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/ Lumilled/ Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79 & 80 certificates from NABL accredited third party lab to be produced mentioning chip manufacturer) (DuroLed Pro Well glass BY202PLED43SCW PSU PC of M/s Signify or equivalent)

OD257870/2022-2023:INTERNAL ELECTRIFICATION:-Supply Conveyance, installation, testing and commissioning of 35 W LED medium bay fitting with output greater than 120 lumen/W 4000-6000 K with IP 66/ IK 8 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.90 at full load, internal surge protection up to 4 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD Less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79&80 certificates from NABL accredited third party lab to be produced mentioning chip manufacturer) (Substation building) To be suspended from ceiling by suitable metallic chain/ bouden and giving connection using 16/0.20 mm 3 core PVC/PVC round flex wire (BY202P LED 435 CW PSU PC SPD of M/s Signify or equivalent)

OD257871/2022-2023:INTERNAL ELECTRIFICATION:-Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

OD257872/2022-2023:INTERNAL ELECTRIFICATION:-Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

OD257873/2022-2023:INTERNAL ELECTRIFICATION:-Supply, conveyance, installation, testing and commissioning of light duty exhaust fans with metal body and metal blades with self opening louvers of the following sizes using standard accessories and giving connection with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire working on 230V/240V single phase A/C supply 225 mm sweep or nearest available size including cutting necessary holes, finishing the holes etc. as required

OD257874/2022-2023:INTERNAL ELECTRIFICATION:-Supply, conveyance, installation, testing and commissioning of heavy duty exhaust fans with metal body and metal blades of the following sizes using standard accessories and giving connection with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire working on 230V/240V single phase A/C supply 450 mm sweep or nearest available size including cutting necessary holes, finishing the holes etc. as required

OD257875/2022-2023:INTERNAL ELECTRIFICATION:-Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 2.00 mm copper conductor ( 14 SWG)

OD257876/2022-2023:INTERNAL ELECTRIFICATION:-Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 3.15 mm copper conductor ( 10 SWG)

OD257877/2022-2023:INTERNAL ELECTRIFICATION:-Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.00 mm (14 SWG)

OD257878/2022-2023:INTERNAL ELECTRIFICATION:-Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required. 3.15 mm (10 SWG)

OD257882/2022-2023:INTERNAL ELECTRIFICATION:-Earthing with GI earth plate 1200 x 1200 x 12 mm thick including accessories and providing masonry enclosure with RCC slab covering, watering pipe, funnel with mesh, required quantity of charcoal/ coke, salt etc as per IS 3043: 2018 as required

OD257883/2022-2023:INTERNAL ELECTRIFICATION:-Supply and laying 32 x 3 mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required

OD257884/2022-2023:INTERNAL ELECTRIFICATION:-Supply and laying 25 x 3 mm copper strip laid in ground including excavation or suitably clamped and giving necessary connections as required

OD257885/2022-2023:INTERNAL ELECTRIFICATION:-SITC of 3 kVA UPS with single phase input and single phase output with 30 min backup in conformity with the detailed technical specifications attached

OD257886/2022-2023:INTERNAL ELECTRIFICATION:-Supply and wiring plug points in combined position in the same system explained as item No.1

OD257889/2022-2023:SAFETIES:- Supply and providing 2 mm elastomeric fire retardant insulating mat as per IS 15652/2006 to withstand 3.3 KV dielectric strength including pasting in ground using synthetic adhesives.

OD257890/2022-2023:SAFETIES:-Supply and providing 2.50 mm elastomeric fire retardant insulating mat as per IS 15652/2006 to withstand 11 KV dielectric strength including pasting in ground using synthetic adhesives.

OD257891/2022-2023:SAFETIES:-Supply and providing Fire Extinguisher ABC type 6 Kg. with hose and clamp.

OD257892/2022-2023:SAFETIES:-Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, colour washing etc.as per IS 2546 as required.

OD257893/2022-2023:SAFETIES:-Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision.

OD257895/2022-2023:SAFETIES:-Supply of 12 KV grade insulated gloves.

OD257897/2022-2023:ENERGY MANAGEMENT SYSTEM:- "Supply, installation, testing and commissioning of Energy Management System (EMS) as per the attached architecture and as explained in the Detailed Technical Specifications (DTS) consisting of Modbus gateway with Dual Ethernet port to convert RS 485 to Modbus TCP (For RS485 meters), required power supply for gateway and smart link, ISO 50001/50006 certified Power Monitoring software, Web View Software, server/ workstation PC as explained in the DTS, connected Service Plan for performing System analysis and network Analysis -Advisor service connected Prime plan[twice a year] connecting up to 90 credit points, Smart link / Easycom etc as required. The system should support a minimum of the following meters and devices or their equivalent approved makes: ION9000, PM8240, PM5560, PM2230H, PM1130H, EM6400NG, EM6438H, EM7230, MTZ with EIFE, NW with IFE, NSX with IFM/IFE, Smart link Modbus, Power Tag, Heat Tag, Wireless Thermal Sensors, Easergy relays, Panel Server etc. "

OD257902/2022-2023:LIGHTNING PROTECTION:- "Providing and fixing Fully Solid Vertical Air terminals for wind stability as per IS/IEC -62305 part-3 For 1,2,3, 4 meter air terminal 16mm rod tapered to 10 mm aluminium rod meter rod: requirement (IS/IEC 62305) Semi-hard (E-AlMgSiO5) Suitable for high wind load. All air terminal must have Interception Tip at the Top of air terminal. System consist of Fang Fix with base and clamp on the top air terminal is erected. Air terminal Joining Clip Stainless Steel SS 304 clamp made of cable bracket, lightning tested for 100 KA 10/350 micro sec waveform. Stainless Steel Wall Clamp or 16 KG stone of 365 mm diameter, high level of stability. No of stones/wall clamps depending on wind load. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman"

OD257903/2022-2023:LIGHTNING PROTECTION:- "Providing & fixing of 8mm solid aluminium round conductor with necessary holders @ required interval as specified below: Shall meet the requirement of (IS/IEC 62305) : semi-hard (E-AlMgSiO5 )with 50 sq.mm cross sectional area. Govt approved Indian labs test certificate required. Make: Cape / Erico / Furse "

OD258203/2022-2023:LIGHTNING PROTECTION:- Providing and fixing of Cross Connector/T Connector/Folding Clamp/Clamping Shoe/ Expansion Piece: to route vertical down conductor /mesh formation made of Aluminium Ferrule using screw free joints. Folding Clamp/Clamping Shoe for metal panels (up to 20mm thickness of the metal frame): Folding clamp/clamping shoe for metal frame thickness up to 20mm, made of stainless steel SS 304/316 grade , conforms to the requirements according to (IS/IEC 62305). Expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length at every 20 meters horizontally. Using round conductor 8mm aluminium conductor with straight Connector: using Aluminium Ferrule. Quick installation using crimp joints. Conforms to the requirements according to (IS/IEC 62305). Make sure all joints are strong and will be inspected at site. Galvanised Iron joints are not permitted to avoid risk of corrosion. Single bolt joints are not permitted to avoid risk of faulty loose joints and reduce risk of flash over. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

OD258218/2022-2023:LIGHTNING PROTECTION:- Providing and fixing of Stainless Steel Test Joint suitable with suitable Outdoor Enclosure: For 8mm dia solid round aluminium conductor & 10mm dia copper coated solid steel round conductor having 100 microns of copper bonding . Conforms to the requirements according to (IS/IEC 62305).The enclosure should be outdoor glass-fibre reinforced polycarbonate opaque having minimum inner dimension of 75mm x 75 mm x 50 mm. The test link has to be straight and needs minimum 4 mounting screws for strong joints. Inspection of bimetallic corrosion at site required. Separation of 8mm Aluminium & 10mm Copper bonded steel is required for future inspection and contractor has to make sure both conductors should not touch each other to avoid bimetallic corrosion. Single bolt joints are not permitted. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

OD258222/2022-2023:LIGHTNING PROTECTION:- "Providing and laying copper coated steel solid round conductor 10mm diameter from earth electrode directly in ground as required. copper coated steel, high corrosion resistant. Meets the requirement of (IS/IEC 62305) copper coating thickness of 100microns Should be tested and use exclusively for lightning protection earthing system and ring equipotential bonding. After test link needs to be routed inside Heavy duty conduit to avoid touch potential till ground level. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman "

OD258233/2022-2023:LIGHTNING PROTECTION:- Installation of Exothermic Weld Joints for 10mm round copper bonded steel conductor having 100 microns as per IS/IEC 62305. Each under ground joints has to be wrapped with petrolatum- coated chemical fibre fabric having 1.1mm thick and width 50mm. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

OD258239/2022-2023:LIGHTNING PROTECTION:- Providing and fixing of maintenance free Earthing system comprises of molecularly bonded copper of 99.9% purity on low carbon steel of min 3048mm length (10 feet), having a diameter of 20mm with copper bonding thickness of 250 microns as per UL 467. The Rod has to be either continuous or with self-coupling peg & bore arrangement with fault current withstand capability of 30 KA rms value for 1 second and I peak of 76 KA. The rod must be having corrosion test, peel off test for uniform coating, 180 degree bend test with out peel off of copper bonding. Exothermic welded Clamp for clamping as suggested as per NBC 2016. Ordinary Stainless steel/Copper alloy universal clamps are not recommended. For self coupling peg & bore arrangement rod needs Impact point on the bottom rod for easy insertion. Earth enhancing mineral compound is used for improving the soil conductivity. The material shall be mineral inert to sub soil and shall not pollute the environment and non corrosive to earth rod. The material should have a resistivity less than 0.2 Ωm. It should be free from hazardous substances. The mineral compound is required to have minimum 25 Kg of the total composite. The compound should be chemically inert and needs to submit Govt approved Indian labs test certificate. Concrete Earth electrode inspection chamber with weight bearing capacity of 50KN. The dimension shall be 320mmx 190mm. Govt approved Indian labs test certificate required. Make: Cape / DEHN / OBO Betterman

PART III - AUTOMATION (SCADA) SYSTEM

OD248069/2022-2023: RWPS & TRANSMISSION MAIN:- Control & Instrumentation system for raw water pump house & Transmission line as per the detailed technical specifications attached

OD259104/2022-2023:WTP, FILTER CONSOLE, CHEMICAL HOUSE, CHLORINE HOUSE, CLARIFIER & OHT LOCATIONS:- C & I system for raw water treatment plant and clearwater pumps as per the detailed technical specifications attached

OD259105/2022-2023:WTP, FILTER CONSOLE, CHEMICAL HOUSE, CHLORINE HOUSE, CLARIFIER & OHT LOCATIONS:-C & I system for filter consoles (12 Nos) as per the detailed technical specifications attached

OD259106/2022-2023:WTP, FILTER CONSOLE, CHEMICAL HOUSE, CHLORINE HOUSE, CLARIFIER & OHT LOCATIONS:- C & I system for chemical house as per the detailed technical specifications attached

OD259107/2022-2023:WTP, FILTER CONSOLE, CHEMICAL HOUSE, CHLORINE HOUSE, CLARIFIER & OHT LOCATIONS:- C & I system for chlorine house as per the detailed technical specifications attached

OD259108/2022-2023:WTP, FILTER CONSOLE, CHEMICAL HOUSE, CHLORINE HOUSE, CLARIFIER & OHT LOCATIONS:- C & I system for clarifier (3 Nos) as per the detailed technical specifications attached

OD259109/2022-2023:WTP, FILTER CONSOLE, CHEMICAL HOUSE, CHLORINE HOUSE, CLARIFIER & OHT LOCATIONS:- C & I system for OH tank locations at Manichithodu, Kottankara, Vadakkevila and Vasoorichira as per the detailed technical specifications attached

OD259110/2022-2023:SUPPLY OF INSTRUMENTS :-Supply of all required instruments as per the detailed technical specification

OD259111/2022-2023:INSTALLATION AND COMMISSIONING :- Erection of all the supplied items including supply and erection of all required hardware items such as power cables, communication cables, Cat6 cables, FO cables, cable trays, other hook-up materials, termination devices including testing and commissioning

OD259112/2022-2023:SITC of UPS of VARIOUS RATINGS :-SITC of UPS of various ratings as per the technical details attached

OD259113/2022-2023:ESTABLISHING BROADBAND CONNECTION:- Establishing broadband connection at RWPS & WTP with static IP with SIM card/ router/ switches etc. and all other required hardware's including all fee to the service provider. The connection shall be obtained from reputed established service provider who offer strong strength in the respective locations. This shall be done in concurrence with the KWA authorities

PART IV -CCTV INSTALLATION- WATER TREATMENT PLANT AND RAW WATER PUMP HOUSE

OD259114/2022-2023:WTP :-SITC of 32 channel NVR with 2 x 6 TB HDD

OD259119/2022-2023:WTP:- 24 Port Gigabit Ethernet L2 PoE switch with 24x PoE+ @ 380W and 1 nos fiber gigabit uplink port

OD259118/2022-2023:WTP :- 8 Port Gigabit Ethernet L2 PoE switch with 8x PoE @ 46W and 1 nos fiber Gigabit uplink port

OD259117/2022-2023:WTP:- SFP 1G Ethernet fiber module

OD259116/2022-2023:WTP:- SITC of Varifocal 4 Mp Dome Camera

OD259115/2022-2023:WTP:- SITC of Varifocal 4 Mp Bullet Camera

OD259120/2022-2023:WTP:- PVC Back box for Camera

OD259121/2022-2023:WTP:- SITC of 55" LED Industrial type monitor (24x7)

OD259123/2022-2023:WTP:- Supply and connecting 10 Mtr HDMI cable and make the system functional

OD259214/2022-2023:WTP:- Supply and connecting 10 Mtr USB extension cable and make the system functional

OD259215/2022-2023:WTP:- SITC of 1 kVA UPS with 1 hour backup

OD259216/2022-2023:WTP:- SITC of 600VA UPS with 30 min backup

OD259217/2022-2023:WTP:- SITC of 12 U rack with fan, PDU, Cable manager, hardware set etc. complete

OD259218/2022-2023:WTP:- SITC of 9U rack with fan, PDU, Cable manager, hardware set etc. complete

OD259219/2022-2023:WTP:- SITC of 24P fully loaded Cat6 patch panel

OD259220/2022-2023:WTP:- SITC of fully loaded 12P LIU

OD259221/2022-2023:WTP:- Fiber patch cord 2 Mtr

OD259229/2022-2023:WTP:- CAT6 patch cord 1 Mtr

OD259231/2022-2023:WTP:- Supply and fixing of Gigabit Transceiver

OD259232/2022-2023:WTP:- Supply and clamping / drawing Cat 6 cable through the existing conduit and giving connections as required

OD259233/2022-2023:WTP:- 6 core armoured multimode fiber cable

OD259234/2022-2023:WTP:- Supply and laying of 25 mm HDPE pipe laid 75 cm below ground including excavation and refilling etc as required

OD259235/2022-2023:WTP:- Supply and laying of 3 core 1.50 sq. mm armoured copper UG cable in trench

OD259236/2022-2023:WTP:- Supply and laying of 3 core 1.50 sq. mm armoured copper UG cable through existing pipe

OD259238/2022-2023:WTP:- Supply and fixing of 6 Mtr Pole for outdoor camera

OD259240/2022-2023:WTP:- Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

OD259241/2022-2023:WTP:- Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

OD259242/2022-2023:RWPS :-SITC of 32 channel NVR with 2 x 6 TB HDD

OD259243/2022-2023:RWPS :- 24 Port Gigabit Ethernet L2 PoE switch with 24x PoE+ @ 380W and 1 nos fiber gigabit uplink port

OD259244/2022-2023:RWPS :- SFP 1G Ethernet fiber module

OD259245/2022-2023:RWPS :- SITC of Varifocal 4 Mp Dome Camera

OD259246/2022-2023:RWPS :- SITC of Varifocal 4 Mp Bullet Camera

OD259247/2022-2023:RWPS :-PVC Back box for Camera

OD259248/2022-2023:RWPS :-SITC of 55" LED Industrial type monitor (24x7)

OD259249/2022-2023:RWPS :-Supply and connecting 10 Mtr HDMI cable and make the system functional

OD259250/2022-2023:RWPS :-Supply and connecting 10 Mtr USB extension cable and make the system functional

OD259251/2022-2023:RWPS :-SITC of 1 kVA UPS with 1 hour backup

OD259252/2022-2023:RWPS :-SITC of 12 DU rack with fan, PDU, Cable manager, hardware set etc. complete

OD259254/2022-2023:RWPS :-SITC of 24P fully loaded Cat6 patch panel

OD259255/2022-2023:RWPS :-CAT6 patch cord 1 Mtr

OD259257/2022-2023:RWPS :-Supply and clamping / drawing Cat 6 cable through the existing conduit and giving connections as required

OD259258/2022-2023:RWPS :-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

OD259260/2022-2023:RWPS :-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

PART V - SOLAR PV INSTALLATION

OD247852/2022-2023:Supply installation All type of testing, trial run and commissioning of solar on grid plant with advanced Mono Perc Half Cut Solar panels, Structures to mount panels, DC cables and connectors DC junction Box, Inverters . AC junction BoxLink,,solar meter with Box, AC cables, Link/CB, TPN Box, Net Meter with approval of KSEB approval and all other electrical and mechanical accessories complete as per the direction of departmental officers and in accordance with Inspectorate standards. All paperwork, statutory fees and allied works with the Electrical inspectorate and KSEB Limited for the approval and to be got approved by Electrical Inspectorate and KSEB Limited (Proposed capacity - AT WTP- 250 kWp , AT RWPS 10 kWp)

PART VI - SUPPLY AND ERECTION OF PUMPSETS

OD259405/2022-2023:VT PUMP AT RWPS: Design, Manufacture, Supply, Installation, Testing and Commissioning (DMSITC) of Vertical Turbine pump conforming to IS 1710: 2021 with latest amendments coupled with 3.30 kV electric motor conforming to relevant Indian Standards suitable for discharging 1264 lps at 81 m (total dynamic head). The electric motor shall be suitable for operation with VFD and compatible for automation. The mechanical efficiency of the pump shall be as specified in the DTS and the efficiency of the electrical motor shall be at least at par with IE3 rated LT motor of the same rating according to IS 12615: 2018. All other components, accessories, safeties, protections, conditions etc. as specified in the detailed technical specification shall be complied with. The specified head and delivery shall be achieved when two pumps are working in parallel. The pump set shall be installed in the existing foundation (2 Nos. working and 2 Nos. standby)

OD259406/2022-2023:HORIZONTAL CENTRIFUGAL PUMP FOR MANICHITHODU: Design, Manufacture, Supply, Installation, Testing and Commissioning (DMSITC) of Horizontal Centrifugal pump conforming to IS 6595: 2018 with latest amendments coupled with 415 V electric motor conforming to relevant Indian Standards suitable for discharging 851.04 lps at 32.50 m (total dynamic head). The electric motor shall be suitable for operation with VFD and compatible for automation. The electric motor shall be suitable for operation with VFD and compatible for automation. The mechanical efficiency of the pump shall be as specified in the DTS and the efficiency of the electrical motor shall be IE3 rated according to IS 12615: 2018. All other components, accessories, safeties, protections, conditions etc. as specified in the detailed technical specification shall be complied with. The specified head and delivery shall be achieved when two pumps are working in parallel. The pump set shall be installed in the existing foundation (2 Nos. working and 1 No. standby)

OD259407/2022-2023:MULTISTAGE PUMP FOR KOTTANKARA: Design, Manufacture, Supply, Installation, Testing and Commissioning (DMSITC) of Horizontal Centrifugal pump conforming to IS 6595: 2018 with latest amendments coupled with 415 V electric motor conforming to relevant Indian Standards suitable for discharging 72 lps at 70 m (total dynamic head). The electric motor shall be suitable for operation with VFD and compatible for automation. The mechanical efficiency of the pump shall be as specified in the DTS and the efficiency of the electrical motor shall be IE3 rated according to IS 12615: 2018. All other components, accessories, safeties, protections, conditions etc. as specified in the detailed technical specification shall be complied with. The specified head and delivery shall be achieved when two pumps are working in parallel. The pump set shall be installed in the existing foundation (2 Nos. working and 1 No. standby)

OD259408/2022-2023:HORIZONTAL CENTRIFUGAL PUMP FOR VADAKKEVILA: Design, Manufacture, Supply, Installation, Testing and Commissioning (DMSITC) of Horizontal Centrifugal pump conforming to IS 6595: 2018 with latest amendments coupled with 415 V electric motor conforming to relevant Indian Standards suitable for discharging 144.91 lps at 34 m (total dynamic head). The electric motor shall be suitable for operation with VFD and compatible for automation. The mechanical efficiency of the pump shall be as specified in the DTS and the efficiency of the electrical motor shall be IE3 rated according to IS 12615: 2018. All other components, accessories, safeties, protections, conditions etc. as specified in the detailed technical specification shall be complied with. The pump set shall be installed in the existing foundation (Rate shall be inclusive of full warranty of the pumps for the first 2 years from the date of commissioning) (2 Nos. working and 1 No. standby)

OD259409/2022-2023:HORIZONTAL CENTRIFUGAL PUMP FOR VASOORICHIRA: Design, Manufacture, Supply, Installation, Testing and Commissioning (DMSITC) of Horizontal Centrifugal pump conforming to IS 6595: 2018 with latest amendments coupled with 415 V electric motor conforming to relevant Indian Standards suitable for discharging 76.08 lps at 36 m (total dynamic head). The electric motor shall be suitable for operation with VFD and compatible for automation. The electric motor shall be suitable for operation with VFD and compatible for automation. The mechanical efficiency of the pump shall be as specified in the DTS and the efficiency of the electrical motor shall be IE3 rated according to IS 12615: 2018. All other components, accessories, safeties, protections, conditions etc. as specified in the detailed technical specification shall be complied with. The specified head and delivery shall be achieved when one pump is working. The pump set shall be installed in the existing foundation (1 No. working and 1 No. standby)

PART VII - CONVERSION OF MECHANICAL VALVES TO ACTUATOR VALVES

OD259410/2022-2023:SITC of electric actuators for 250 NB & 300 NB butterfly valve ON/OFF duty, supply voltage 230V

OD259411/2022-2023:SITC of electric actuators for 350 NB & 400 NB butterfly valve ON/OFF duty, supply voltage 230V

OD259413/2022-2023:SITC of electric actuators for 600 NB butterfly valve ON/OFF duty, supply voltage 230V

OD259414/2022-2023:SITC of electric actuators for 250 NB & 300 NB butterfly valve control duty, supply voltage 230V

OD259415/2022-2023:SITC of electric actuators for 350 NB & 400 NB butterfly valve control duty, supply voltage 230V

OD264627/2022-2023:SITC of electric actuators for 600 NB butterfly valve control duty, supply voltage 230V

Supply,erection and commissioning Raw water pump set at Intake and allied works at Njankadavu

OD270817/2022-2023:Fabricating spirally welded MS pipes of size 700 mm (ID) using 12.50 mm thick MS plate including cost and conveyance charges of MS plate,all fabrication charges, charges of painting the steel work with two or more coat epoxy paint (inside & out side of the pipe) to give an even shade over an under coat of primer etc complete.

OD270791/2022-2023:Fabricating spirally welded MS pipes of size 1219 mm (OD) using 12.50 mm thick MS plate including cost and conveyance charges of MS plate,all fabrication charges, charges of painting the steel work with two or more coat epoxy paint (inside & out side of the pipe) to give an even shade over an under coat of primer etc complete.

OD270790/2022-2023:Fabricating MS flanges of diameter 700 mm (ID) using 20 mm thick MS plate including cost and conveyance charges of MS plate,all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete: For pipes fabricated with 12.50 mm thick MS plates.

OD270789/2022-2023:Fabricating MS flanges of diameter 1200 mm (ID) using 20 mm thick MS plate including cost and conveyance charges of MS plate,all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete: For pipes fabricated with 12.50 mm thick MS plates.

OD270785/2022-2023:Conveying from stack and laying and ready for jointing 12.50 mm thick spirally welded mild steel pipe suitable for taper sleeve joint of 700 mm (ID) or nearest available size including labour, primary air testing of joints, hydraulic test, commissioning etc including all protection measures as per the specifications and directions of the engineer in charge.

OD270784/2022-2023:Conveying from stack and laying and ready for jointing 12.50 mm thick spirally welded mild steel pipe suitable for taper sleeve joint of 1219 mm (OD) or nearest available size including labour, primary air testing of joints, hydraulic test, commissioning etc including all protection measures as per the specifications and directions of the engineer in charge.

OD270783/2022-2023:Jointing 1200 mm ID 12.50 mm thick MS pipe already laid to line and levels by 3 run each face welding(Inside and Out side) after grinding the pipe ends in V cut shapes etc . Complete <b

100.37.15.3:Cutting 700mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.15.5:Grinding cut and weld edges of 700mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

OD270782/2022-2023:Jointing 700 mm ID 12.50 mm thick MS pipe already laid to line and levels by 3 run welding after grinding the pipe ends in V cut shapes etc . Complete <br>

100.19.1:Providing flanged joints to double flanged CI/DI pipes and specials, including testing of joints: 700mm Diameter Pipe.

OD270781/2022-2023:Fabricating MS Dummy plate of diameter 1319 mm (OD) using 20 mm thick MS plate including cost and conveyance charges of MS plate,all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete:

OD270780/2022-2023:Supply and installation of flow meters and accessories of size 1200 mm -Supplying an Electromagnetic Flow meter confirming to protection level of IP-68 for Flow sensor and IP 67 for transmitter and having an accuracy level of 0.5% with LED /LCD display unit.The flow meter should have the housing (Flow sensor) to be made of ISS 304/Carbon steel with anti corrosive protection and inside liner to be made up to Hard Rubber/neoprene all confirming to drinking water standads. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturer should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions vide circular no. KWA /HO/SP-4014/2012/Flow meter and Soft starter dt 5/9/2012.The flowmeter has to be installed after cutting the existing pumping main 1219 mm fixing the necessary flange pipes and all other required accessories as per the directions of department officers-Test certificate from FCRI Palakkad.

100.31.2.13:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 700mm diameter, Class II.

OD270779/2022-2023:Supply and erection of 700 mm DI Single Door/ Multi Door Non return valve with dismantling joint conforming to IS 5312/2003(part I & II or latest edition)16kg /cm2 or above to be fixed near Pump for 90% fast closing & 10% slow closing.Supply of valves includes 5 years warranty

OD270778/2022-2023:Supply and fixing of electrically operated DI Double Flanged Sluice Valve with dismantling joint Conforming to IS 14846 - 2000 or latest , Sluice Valve with Cap PN 1.6, Size 700mm .Supply of valves includes 5 year warranty.

OD270777/2022-2023:Supply and erection of 1200mm DI Double Flanged electrically operated Sluice Valve with dismantling joint Conforming to IS 14846 - 2000 or latest, Sluice Valve with Cap PN 1.6 or above with LT2B seat.Supply of valves includes 5 year warranty.

OD270776/2022-2023:supply and erection of 1200 mm dia DI D/F Multi Door Non return valve fixing with dismantling joint conforming to IS 5312/2003(part I & II or latest), PN 1.6 or above to be fixed after Water meter/ Flow recorder on pumping main near Pump house with dash pot arrangement for 90% fast closing & 10% slow closing.

100.37.7.1:In situ fabrication of M.S. pipes of size 200mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.7.2:Fabricating M.S. flanges of diameter 200mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.7.3:Cutting 200mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.7.4:Welding 200mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.7.5:Grinding cut and weld edges of 200mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.98.461:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 200mm.

100.31.2.5:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 200mm diameter, Class II.

100.98.447:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Double Orifice Type DS2, Size 200mm.

100.32.7:Conveying and fixing C. I. Double Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 200mm Double Acting Air Valve.

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD270775/2022-2023:Interconnecting the delivery side of pump set with pumping main using not less than 8.8mm thick MS Pipe including cutting, grinding, welding, pressure testing the welded joint, cost of MS Pipe,cost 700mm & 1200mm sleeve coupling etc complete as per directions of deptl: officers

OD273768/2022-2023:Shifting the KSEB 11 KV Electric post from the proposed Sub station building at Njankadavu towards a convenient position including the all charges of shifting the post and office expenses. etc complete as per directions.

Constructing Valve Chamber- Raw water pumpset

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete.

Additional warrenty- Raw water pump set

OD273775/2022-2023:Additional Warranty for 3rd year

OD273774/2022-2023:Additional warranty for 4th year - Raw water pump set

OD273773/2022-2023:Additional warranty for 5th year - Raw water pump set

OD273790/2022-2023:Operation and maintenance for the pumpset for 36 months(0.2% of total estimate cost for 1 year) - Raw water pumpset

Supply, erection & commissioning centrifugal pump set for clear water pumping main from clear water sump to OHSR at Manichithodu

100.37.19.1:In situ fabrication of M.S. pipes of size 1000mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

OD273841/2022-2023:Conveying from stack and laying and ready for jointing 8. mm thick spirally welded mild steel pipe suitable for taper sleeve joint of 1016 mm (OD) or nearest available size including labour, primary air testing of joints, hydraulic test, commissioning etc including all protection measures as per the specifications and directions of the engineer in charge.

OD273854/2022-2023:Fabricating MS Dummy plate of diameter 1116 mm (OD) using 20 mm thick MS plate including cost and conveyance charges of MS plate,all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete: For pipes fabricated with 20.00mm thick MS plates.

OD273848/2022-2023:Jointing 1016 mm OD 8 mm thick MS pipe already laid to line and levels by 3 run welding after grinding the pipe ends in V cut shapes etc . Complete <br>

OD273851/2022-2023:Supply and installation of flow meters and accessories of size 1000 mm -Supplying an Electro Magnetic Flow meter confirming to protection level of IP-68 for Flow sensor and IP 67 for transmitter and having an accuracy level of 0.5% with LED /LCD display unit. The flow meter should have the housing (Flow sensor) to be made of ISS304/Carbon steel with anti corrosive protection and inside liner to be made up to Hard Rubber/neoprene all confirming to drinking water standads. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturer should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions vide circular no. KWA /HO/SP-4014/2012/Flow meter and Soft starter dt 5/9/2012.The flow meter has to be installed after cutting the existing 1000 mm pumping main fixing the necessary flange pipes and all other required accessories as per the directions of department officers-Test certificate from FCRI Palakkad.

OD273845/2022-2023:Fabricating MS flanges of diameter 1016 mm (ID) using 20 mm thick MS plate including cost and conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete: For pipes fabricated with 8.8 mm thick MS plates.

100.19.5:Providing flanged joints to double flanged CI/DI pipes and specials, including testing of joints: 1000mm Diameter Pipe.

100.37.14.1:In situ fabrication of M.S. pipes of size 600mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.14.2:Fabricating M.S. flanges of diameter 600mm using 16mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.14.3:Cutting 600mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.14.4:Welding 600mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.14.5:Grinding cut and weld edges of 600mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.31.2.12:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 600mm diameter, Class II.

OD273859/2022-2023:supply of 600 mm DI/DF sluice valve PN 1.6 and above with electrically operation

OD273858/2022-2023:Supply and erection of 1000 mm DI Multi Door Non return valve conforming to IS 5312/2003(part I & II or latest) to be fixed after Water meter/ Flow recorder on pumping main near Pump house with dash pot arrangement for 90% fast closing & 10% slow closing.warranty for 5 years.

OD273857/2022-2023:Supply and erection of 1000 mm DI D/F electrically operated SLUICE VALVE WITH CAP/ WHEEL AS PER IS 14846/2000 PN 1.6 or above WITH ISI MARKING with 5year warranty

OD273863/2022-2023:Supply and Erection of 600 mm DI Single Door Non return valve conforming to IS 5312/2003(part I & II or higher ) to be fixed after Water meter/ Flow recorder on pumping main near Pump house with dash pot arrangement for 90% fast closing & 10% slow closing.

100.37.7.1:In situ fabrication of M.S. pipes of size 200mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.7.2:Fabricating M.S. flanges of diameter 200mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.7.3:Cutting 200mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.7.4:Welding 200mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.7.5:Grinding cut and weld edges of 200mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.98.461:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 200mm.

100.31.2.5:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 200mm diameter, Class II.

100.98.447:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Double Orifice Type DS2, Size 200mm.

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD273869/2022-2023:Additional warranty for 3rd Year - Manichithode

OD273868/2022-2023:Additional warranty for 4th Year - Manichithode

OD273867/2022-2023:Additional warranty for 5th Year - Manichithode

Constructing Valve Chamber- Clear water pumpset

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.2:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete.

Supply, erection & commissioning centrifugal pump set for clear water pumping main from clear water sump to OHSR at Vadakkevila

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

100.1.5:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50 m, in Ordinary Rock.

OD274904/2022-2023:Conveying 500mm DI K9 pipe from stacking place at Store compound, Kollam to work site at Vasoorichira and engaging heavy load man mazdoor for loading 500 mm DI K9 pipes from stacking place to lorry and unloading the same from the lorry to work site and stacking the pipes at suitable place near work site with out any damages, including hire charges of motor lorry etc complete as per direction

100.14.9:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 500mm diameter Ductile Iron Class K-9 Pipes.

100.31.2.2:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 100mm diameter, Class II.

100.31.2.7:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 300mm diameter, Class II.

100.31.2.11:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 500mm diameter, Class II.

100.32.5:Conveying and fixing C. I. Double Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 100mm Double Acting Air Valve.

100.37.5.1:In situ fabrication of M.S. pipes of size 100mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.5.2:Fabricating M.S. flanges of diameter 100mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.3:Cutting 100mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.4:Welding 100mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.5:Grinding cut and weld edges of 100mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.98.445:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Double Orifice Type DS2, Size 40mm.

100.98.463:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 300mm.

100.98.467:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 500mm.

18.70.9:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:500 mm dia pipes

18.30.11:Providing flanged joints to double flanged C.I./ D.I pipes and specials, including testing of joints:500 mm diameter pipe

18.68.1:Providing and laying D.I specials of class K - 12 suitable for push - on jointing as per IS : 9523 :Upt 600 mm dia

18.83.11:Labour for cutting C.I. pipe with steel saw.500 mm diameter C.I pipe

OD274925/2022-2023:Supply and installation of flow meters and accessories of size 500 mm -Supplying an Electro Magnetic Flow meter confirming to protection level of IP-68 for Flow sensor and IP 67 for transmitter and having an accuracy level of 0.5% with LED /LCD display unit. The flow meter should have the housing (Flow sensor) to be made of ISS304/Carbon steel with anti corrosive protection and inside liner to be made up to Hard Rubber/neoprene all confirming to drinking water standads. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturer should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions vide circular no. KWA /HO/SP-4014/2012/Flow meter and Soft starter dt 5/9/2012.The flow meter has to be installed after cutting the existing 500 mm pumping main fixing the necessary flange pipes and all other required accessories as per the directions of department officers-Test certificate from FCRI Palakkad.

OD275300/2022-2023:Additional warranty for 4th Year - Vadakkevila

OD275301/2022-2023:Additional warranty for 3rd Year - Vadakkevila

OD275304/2022-2023:Additional warranty for 5th Year - Vadakkevila

OD276362/2022-2023:Interconnecting the delivery side of pump set with pumping main using not less than 8.8mm thick MS Pipe including cutting, grinding, welding, pressure testing the welded joint, cost of MS Pipe etc complete as per directions of deptl: officers

OD276600/2022-2023:supply and Erection of 500 mm D/F DI Single Door Non return valve conforming to IS 5312/2003(part I & II or higher) to be fixed after Water meter/ Flow recorder on pumping main near Pump house with dash pot arrangement for 90% fast closing & 10% slow closing.

OD280348/2022-2023:Supply and erection of actuators for operation of 200 to 400 mm Valve with control switches and cabling

100.98.458:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 100mm.

Construction valve chamber- Vadakkevila

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete.

Supply, erection & commissioning centrifugal pump set for clear water pumping main from clear water sump to 20 LL capasity OHSR at vasoorichira.

18.30.8:Providing flanged joints to double flanged C.I./ D.I pipes and specials, including testing of joints:350 mm diameter pipe

18.70.6:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:350 mm dia pipes

18.83.8:Labour for cutting C.I. pipe with steel saw.350 mm diameter C.I pipe

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

100.14.6:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 350mm diameter Ductile Iron Class K-9 Pipes.

100.31.2.5:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 200mm diameter, Class II.

100.98.464:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 350mm.

OD281552/2022-2023:supply of 350 mm CI D/F PN 1.6 non return valve with relevant Is code.

100.31.1.8:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 350mm diameter, Class I.

100.98.461:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 200mm.

OD281559/2022-2023:Supply and installation of flow meters and accessories of size 350 mm -Supplying an Electro Magnetic Flow meter confirming to protection level of IP-68 for Flow sensor and IP 67 for transmitter and having an accuracy level of 0.5% with LED /LCD display unit. The flow meter should have the housing (Flow sensor) to be made of ISS304/Carbon steel with anti corrosive protection and inside liner to be made up to Hard Rubber/neoprene all confirming to drinking water standads. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturer should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions vide circular no. KWA /HO/SP-4014/2012/Flow meter and Soft starter dt 5/9/2012.The flow meter has to be installed after cutting the existing 350 mm pumping main fixing the necessary flange pipes and all other required accessories as per the directions of department officers-Test certificate from FCRI Palakkad.

OD281560/2022-2023:Supply and erection of actuators for operation of 200 to 400 mm Valve with control switches and cabling

OD281566/2022-2023:Additional warranty for 3rd Year - Vasoorichira

OD281564/2022-2023:Additional warranty for 5th Year - Vasoorichira

OD281565/2022-2023:Additional warranty for 4th Year - Vasoorichira

Construction valve chamber- Vasoorichira

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete.

Supply, erection, commissioning centrifugal pump set for clear water pumping main from clear water sump to kottamkara

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

100.1.5:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50 m, in Ordinary Rock.

100.31.1.9:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 400mm diameter, Class I.

100.31.2.2:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 100mm diameter, Class II.

100.31.2.6:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 250mm diameter, Class II.

100.32.5:Conveying and fixing C. I. Double Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 100mm Double Acting Air Valve.

100.37.5.1:In situ fabrication of M.S. pipes of size 100mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.5.2:Fabricating M.S. flanges of diameter 100mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.3:Cutting 100mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.4:Welding 100mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.5:Grinding cut and weld edges of 100mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.11.1:In situ fabrication of M.S. pipes of size 400mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.11.2:Fabricating M.S. flanges of diameter 400mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.11.3:Cutting 400mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.11.4:Welding 400mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.11.5:Grinding cut and weld edges of 400mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.98.455:Supply of CI Air Valve with Flanges, Conforming to IS 14845 - 2000, Kinetic Air Valve Type DS2, Size 100mm.

100.98.458:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 100mm.

100.98.462:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 250mm.

100.98.489:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Hand Wheel PN 1.6, Size 400mm.

18.30.9:Providing flanged joints to double flanged C.I./ D.I pipes and specials, including testing of joints:400 mm diameter pipe

18.70.7:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:400 mm dia pipes

18.83.9:Labour for cutting C.I. pipe with steel saw.400 mm diameter C.I. pipe

18.68.1:Providing and laying D.I specials of class K - 12 suitable for push - on jointing as per IS : 9523 :Upt 600 mm dia

OD281594/2022-2023:Supply and installation of flow meters and accessories of size 400 mm -Supplying an Electro Magnetic Flow meter confirming to protection level of IP-68 for Flow sensor and IP 67 for transmitter and having an accuracy level of 0.5% with LED /LCD display unit. The flow meter should have the housing (Flow sensor) to be made of ISS304/Carbon steel with anti corrosive protection and inside liner to be made up to Hard Rubber/neoprene all confirming to drinking water standads. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturer should have the calibration standards as per ISO 17025 and the product shall have sufficient warranty provisions vide circular no. KWA /HO/SP-4014/2012/Flow meter and Soft starter dt 5/9/2012.The flow meter has to be installed after cutting the existing 400 mm pumping main fixing the necessary flange pipes and all other required accessories as per the directions of department officers-Test certificate from FCRI Palakkad.

OD281595/2022-2023:supply of 400 mm DI D/F PN 1.6 Single Door Non return valve conforming to IS 5312/2003(part I & II or higher) to be fixed after Water meter/ Flow recorder on pumping main near Pump house with dash pot arrangement for 90% fast closing & 10% slow closing

OD281597/2022-2023:Supply and erection of actuators for operation of 200 to 400 mm Valve with control switches and cabling

OD281599/2022-2023:Additional warranty for 5th Year - Kottamkara

OD281600/2022-2023:Additional warranty for 4th Year - Kottamkara

OD281601/2022-2023:Additional warranty for 3rd Year - Kottamkara

Construction valve chamber- Kottamkara

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.2:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete.

Operation and maintenance for the pumpset for 36 months

OD281623/2022-2023: Operation and maintenance for the pumpset for 36 months(0.2% of total estimate cost for 1 year)

CONSTRUCTION OF SUBSTATION BUILDING AT NJANKADAVU

2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.33.1:Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 30 cm girth up to and including 60 cm girth

2.33.2:Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 60 cm girth up to and including 120 cm girth

2.33.3:Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyond 120 cm girth up to and including 240 cm girth

20.2A.1:Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles

20.6.1.2:Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge. Single pile upto 50 tonne capacityRoutine test

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

OD43611/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work upto plinth level

OD43707/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work above plinth level upto floor V level

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.11.1:Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.6:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.3:Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts,locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer .

10.6.1:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.11.1:Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side/top/centre hung, with beading and all members such as F7D, F4B, K11B and K 12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

10.13.1:Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee- sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

13.9.1:Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

11.38:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

16.89:Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi models location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

17.2.1:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.4.1:Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre white P.V.C. automatic flushing cistern

17.7.3:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

18.10.2:Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work- Exposed on wall20 mm dia nominal bore

18.17.1:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.58.1.1:Providing and fixing PTMT grating of approved quality and colour. Circular type100 mm nominal dia

18.65:Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

17.73.1:Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms

17.16A:Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge

17.28.2.1:Flexible pipe32 mm dia

17.32.2:Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

OD44379/2023-2024:Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 2. 15 to below 25 flush capacity

10.26.2:Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.E.R.W. tubes

13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.52.1:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.71:Lettering with black Japan pint of approved brand and manufacture

50.18.7.3.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

50.18.7.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.8.3.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 12 kgf/cm2

50.18.8.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.9.9.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.9.2:Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in CHarge. 110 mm dia 4 Kg/cm2

50.18.9.19.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

18.12.8:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work80 mm dia nominal bore

18.31.1.2:Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately): 100 mm diameterClass II

OD44634/2023-2024:Supply erection trial running and commissioning of 100 KLD capacity pressure filter with M.S body , suitable sand filter media, pneumatic valves and controls for automatic operation including back wash arrangements etc including all accessories as per IS specifications.

CONSTRUCTION OF MAINTENANCE BAY

20.2A.1:Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

OD45135/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work above plinth level upto floor V level

OD45136/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work upto plinth level

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.21:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick.

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.6:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

10.6.1:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

10.16.2:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

OD45164/2023-2024:Design, manufacturing, assembling, testing, transporting, delivery at site, required fabrication,final painting, installation at site, trail running, commissioning , performance testing and handing over to KWA of 7.5 ton capacity EOT crane at Njankadavu well site maintenance bay with necessary mechanical, electrical and civil works including fitting, fixers and accessories. The crane shall be comforting to IS 3177, IS 807, IS 2266, IS 13834 (Part 1 & 5), IS 325, IS 5749, IS 800, ISO 12488-1. The crane shall be having bridge structure,long travel sporting girder, travelling mechanism for long and cross travel, track wheel for long and cross travels, trolley, hoisting mechanism, break mechanism separately for long, cross and hoisting pendant control with remote operation of all movements electrical motors, control gear and equipment, AC variable frequency controls and all motions of the crane, providing suitable rails etc with necessary civil works required at site. All electrical components, trailing/flexible cables, protective switch gears, motor and control panels and power and control cables, CT Motion cables shall running cable rag chain IGUS Drag link cable system, pended and wireless remote, earthing as per IE rules, shrouded bus bar GI conductor etc complete all electrical accessories of the satisfactory completion of the girder as per the direction of deptl: officers. 1. Hoisting capacity - 7.5 Ton, 2. Span - 6.00m, 3. Long Travel - 8.00m, 4. Lifting rang - 6.00m, 5. Main hoist speed - 3m/min (Max), 6. Long travel speed - 20m/min (max), 7. Cross travel speed - 16m/min (max), 8. Duty class of crane M7, 9. Materials for equipment and structure as per IS 2062(latest), 10. Wire rope - Galvanized type of 6x36 construction with tensile strength not less than 180Kg/mm2. 11. Gears as per IS 4460 -1967 or latest. 12. Breaks for LT and CT with fail safe DC disc type, hoisting break with electro hydraulic thrust er break and fail safe DC disc type, 13. Rail wheels with minimum hardness 320 VHN, 14. Lifting hook as per IS 3815 and IS 8610.

OD45166/2023-2024:Design, manufacturing, assembling, testing, transporting, delivery at site, required fabrication,final painting, installation at site, trail running, commissioning , performance testing and handing over to KWA of 10 ton capacity EOT crane at Njankadavu well site with necessary mechanical, electrical and civil works including fitting, fixers and accessories. The crane shall be comforting to IS 3177, IS 807, IS 2266, IS 13834 (Part 1 & 5), IS 325, IS 5749, IS 800, ISO 12488-1. The crane shall be having bridge structure,long travel sporting girder, travelling mechanism for long and cross travel, track wheel for long and cross travels, trolley, hoisting mechanism, break mechanism separately for long, cross and hoisting pendant control with remote operation of all movements electrical motors, control gear and equipment, AC variable frequency controls and all motions of the crane, providing suitable rails etc with necessary civil works required at site. All electrical components, trailing/flexible cables, protective switch gears, motor and control panels and power and control cables, CT Motion cables shall running cable rag chain IGUS Drag link cable system, pended and wireless remote, earthing as per IE rules, shrouded bus bar GI conductor etc complete all electrical accessories of the satisfactory completion of the girder as per the direction of deptl: officers. 1. Hoisting capacity - 10 Ton, 2. Span - 11.80m, 3. Long Travel - Circular Motion 12.00m dia, 4. Lifting rang - 6.00m, 5. Main hoist speed - 3m/min (Max), 6. Long travel speed - 20m/min (max), 7. Cross travel speed - 16m/min (max), 8. Duty class of crane M7, 9. Materials for equipment and structure as per IS 2062(latest), 10. Wire rope - Galvanized type of 6x36 construction with tensile strength not less than 180Kg/mm2. 11. Gears as per IS 4460 -1967 or latest. 12. Breaks for LT and CT with fail safe DC disc type, hoisting break with electro hydraulic thrust er break and fail safe DC disc type, 13. Rail wheels with minimum hardness 320 VHN, 14. Lifting hook as per IS 3815 and IS 8610

CONSTRUCTION OF COMPOUND WALL

2.32:Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.9.1:Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

7.1.1:Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.1.6:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

10.25.2:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13.52.1:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

WELL PROTECTION WORK:- RETAINING WALL,PATH WAY

2.32:Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

50.2.3.1:Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

50.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

7.1.1:Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

7.7.1:Coursed rubble masonry (second sort) with hard stone in foundation & plinth with:Cement mortar 1:6 (1 cement : 6 coarse sand)

OD45539/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work upto plinth level

20.2.4:Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).500 mm dia piles

20.6.1.2:Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge. Single pile upto 50 tonne capacityRoutine test

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

OD45745/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work above plinth level upto floor V level

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.23:Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

PROVIDING AND FIXING CONCRETE TILES AND LANDSCAPING ON YARD

16.91.2:Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

OD45793/2023-2024:Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of serviceable material?s as per direction of officer in charge( including cast of plant & water )<br>Cost of plantation per trees plants.as per the direction of departmental officers.

OD45795/2023-2024:Providing and fixing Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and even, watering with sprinkler

CONSTRUCTING VALVE CHAMBER AT INTAKE ARRANGEMENTS

100.7.2:Bailing out water with engine and pump set above 5HP up to 10HP including conveyance to the site, erecting, dismantling and taking back of engine and pump, cost of fuel lubricating oil and other stores pay of staff etc., complete.

100.52.S.1:Sub Data for providing Earth filled cement bags including cutting of the Earth, filling, conveying and placing in position.

100.52.S.4:Sub Data for Conveying and providing bamboo poles for reinforcing the temporary bund including the cost materials and labour charges etc. complete.

100.52.S.5:Sub Data for Dismantling the sand / earth filled cement bag from the foundation site of bund, apron on both sides, counter wall and removing the sand/earth from the bag and disposing the damaged cement bags properly as per the direction of the department officers including all cost of labour charges etc complete.

20.2A.1:Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete.

OD50791/2023-2024:Providing and fixing CI/MS Foot rest 30cm C/C in zig zag direction on side wall of the chamber as per direction.

10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

OD50812/2023-2024:Supplying and fixing heavy weight CI shutter of size 100 x 100cm with frame including arrangements for operating this shutter from the top of floor slab of pump house using required size threaded MS spindle with bearing systems and wheel for operating and the spindle fixing properly in the inside wall of well including making the mould, all labour charges, conveyance charge etc complete as per directions.

CONSTRUCTING NEW ROAD BY PROVIDING INTERLOCK BRICKS AND CHANNEL TO RIVER ALONG THE ROAD

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

16.1:Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

16.68:Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

CONSTRUCTION OF TRANSFORMER BUILDING FOR CLEAR WATER PUMPING STATION AT VASOORICHIRA.

2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.3.1:Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

16.78.3:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade - III ( size range 26.5 mm to 0.075 mm) having CBR Value - 20

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

OD51614/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work upto plinth level

7.1.1:Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

OD51623/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. .All work above plinth level upto floor V level

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.11.1:Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.6:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

10.11.1:Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side/top/centre hung, with beading and all members such as F7D, F4B, K11B and K 12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

10.13.1:Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee- sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.3.1:Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood

50.9.4.1:Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.6.1:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

13.9.1:Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.48.2:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture

13.52.1:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.71:Lettering with black Japan pint of approved brand and manufacture

RUBBLE WALL FOR PROTECTING LAKE SHORE

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

7.1.1:Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

7.2.1:Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.Cement mortar 1:6 (1 cement : 6 coarse sand)

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

13.33.1:Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing

Bidder Name

Chicago Constructions International Pvt Ltd