Installation of pumping machinery and repair of Electro mech equipment and providing of Starter panel for various pumping station of Sub Division Rajouri

Amount

Laying of foundation block of RCC for installation of HCP 5000 GPH X 250 MH at pumping station Bhatian.The job includes fabrication, welding and laying of steel mesh made from 10 mm tor steel placed horizontally, vertically and diagonally at equal distance including form work. Laying of foundation block of RCC in the ratio 1:2:4 (cement, sand and Bajri) and grouting of fabricated foundation bolts. The entire block to be laid in such a way that it can dump all types of mechanical vibration created by dynamic load of the pump. Placing of base frame and leveling. Tightening of base frame by fastening of 6 No. foundation bolts. Fabrication and relaying of suction/delivery by way of P/F of sluice valve 65mm dia-01 no , check valve 65mm dia -01 no at delivery side, P/F bends, MS flanges, nut bolt and rubber washers etc. required at site with complete welding work. Complete job includes cost of all types of material such as cement, sand, Bajri, tor steel, foundation bolts, nuts, washers, bolts, carriage of material to site of work on H/L, higher charges of tools and tackles, labour charges of skilled and semi-skilled workers. Complete job

Providing, Installation, testing and Commissioning of Submersible pump set 1000GPH×100MH Single Phase along with allied electromechanical equipments for commissioning of 125mm dia Bore Well at Dak Bangla Rajouri The job includes providing of submersible pump motor, assembling at site. Providing/fitting of Sub Cable 4mm sq 3 Core Cu. approximate Length 120m from Sub motor to submersible control Panel fitted on switch Board. Providing/fabrication of PVC Hose pipe 32 mm dia, length 280 Feet fitted with bell cap at one end and G.I.pipe nipple at other end with proper riveting. Job also includes P/F of support wire and lowering of pump motor assembly in to the bore well. Providing /Fitting of 3HP submersible control Panel of good quality fitted with Voltmeter, Ampere meter etc. Complete job includes cost of material, hire charges, labour charges, carriage charges & fitment charges at the site of work. Testing of pumping machinery at full load.

Replacement of Sluice Valve 65mm dia- 02 nos. and check valve 65mm dia. 01nos.at pumping station Trala by way of dismantling of old damaged sluice valve by providing and fitting of new sluice valves with flanges, nut bolts, washers with allied welding works. The job includes cost of material and labour charges at site.

Providing & fitting 3.5 core Aluminium cable of 185 mm sq at pumping station Sagrwat Bore Well . Job involves removing the damaged/burnt out cable from LT pole to main switch. Providing and fitting of new cables from LT pole to main switch after proper thimbling. Complete job includes the cost of material, labour charges and carriage charges at site.

Providing & fitting of 50 HP star delta oil immersed double contact starter at pumping station Androlla. Job involves removing the damaged/burnt out starter from the panel board after disconnecting the electrical cables. Providing of new 50 HP starter & fitting it on the panel board with the help of fasteners. Reconnecting the electrical cables to the starter after cutting their overheated /damaged ends and thimbling them properly and testing it on full load job also involves calibration of its overload protection according to its load. Complete job includes the cost of material, labour charges and carriage charges at site.

Providing/Fitting of 200Amp Main Switch at Pumping Station Nainsukh. Job involves drilling of holes in the panel board, Providing & fitting of nuts, bolts & washers etc. Replacement of copper cable 19/16 damaged i.e. burnt/ burst from Main Switch to Voltage stabilizer up to motor (Approx. length 40m).Providing/Fitting of Ampere meter 1No. of range 0-200Amp.& thimbles. Complete job includes cost of material, labour charges and carriage charges at site of work.

Providing & fitting of 7.5 HP submersible control panel at pumping station Pota Radha D/Well Job involves removing the damaged/burnt out submersible control panel from the panel board after disconnecting the electrical cables. Providing of new 7.5 HP submersible control panel & fitting it on the panel board with the help of fasteners. Reconnecting the electrical cables to the panel after cutting their overheated /damaged ends and thimbling them properly and testing it on full load job also involves calibration of its overload protection according to its load. Complete job includes the cost of material, labour charges and carriage charges at site.

Providing/ Fitting of Cu. 3 Core Submersible Cable 16mmSq. in place of damaged i.e. burnt/burst from Panel to Sub. Motor(Approx 60mtr) at pumping station New Bella B/Well. Job also includes providing and fitting of 200 Amp. Capacity Main switch in place of damaged switch. Complete job includes cost of material, labour charges fitting charges at site of work.

Vaibhav Engineers and Technocrates

VEE AUTO TRADERS