GENERAL-Construction of NCC Directorate building at Vazhuthacaud in Thiruvananthapuram District- Phase 2-New Work-Composite Work

Appendix A - Building Proper(Civil work)

OD286321/2025-2026:Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. ( Note- cement content considered in this item is @ 340kg/cum. Excess or less cement used as per design mix is not payable or recoverable seperately) All work above plinth level upto floor V level

5.22A.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.19:Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.6.1.2:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

50.6.1.3:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure above floor two level up to floor V level thickness 20cm and above in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.6.3.2:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

50.13.1:9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

21.18:Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

OD201962/2025-2026:Supplying and fixing 200 mm Stainless steel ,Grade 304 aldrop

OD201960/2025-2026:Supplying and fixing 180 mm Stainless steel ,Grade 304,tower bolt

OD201961/2025-2026:Providing and fixing stain less steel, Grade 304 handles: 150 mm

10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.80:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.46.1:Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

OD201965/2025-2026:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS :15622,of approved make, in all colors and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) and grouting the joints of tiles having joints of 3mm width ,using epoxy grout mix of 0.70kg of organic coated filler of desired shade (0.10kg of hardener and 0.20 kg of resin per kg) including filling /grouting and finishing complete as per direction of Engineer-in -charge. Size of Tile 600x600 mm

OD201963/2025-2026:Providing and laying rectified ceramic floor tiles 600 x 600 mm size( thickness to be specified by the manufacturer ) of 1st quality of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4( 1 cement : 4 coarse sand) and grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg) including filling/grouting and finishing complete as per direction of Engineer in charge etc complete . Size of tile 600 x 600 mm

OD201966/2025-2026:Providing and laying rectified Ceramic Wall tiles 600x600 mm of 1st quality of approved make, in all colours & shade, in walls, skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), complete including Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. .Size of Tile 600x600 mm

OD201964/2025-2026:Providing and laying Vitrified Wall tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), excluding grouting the joint with white cement & matching pigments etc. complete. and Grouting the joints of tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineerin- charge Size of Tile 600x600 mm

11.55.1: Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

9.143:Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.118.1:Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter).

9.118.2:Providing and fixing to existing door frames30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

9.147B.1:Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

9.147A.3:Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm).

9.147A.6:Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm , & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm).

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

9.48.2:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD201959/2025-2026:Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick stone aggregate of 6 mm, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

11.19.3:Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand):Dark shade pigment using ordinary cement

16.90:Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

25.1:Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).The weight of aluminum extruded section shall be taken for purpose of payment

25.6: Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc., all complete for the required performance as specified, as per the architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in - Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass panels in the curtain glazing is included in cost of relevent item*). ?(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. .The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

13.45.1:Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

OD283630/2025-2026:Providing and laying Cladding Tiles (Natural Stone) in different sizes (thickness to be specified by the manufacturer), of approved brand & manufacturer in Natural Stone shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness. Size of Tile 200x100 mm

OD284384/2025-2026:Fabricating, supplying and fitting Stainless steel letters (English or Malayalam) to the name board with bolt and nuts, drilling and fixing to the panel with synthetic resin adhesive to correct lines and levels as per the direction of the departmental engineers. Letters made of 0.8mm Stainless Steel sheet, having a height of 88mm and a projection of 25mm from the base.

OD284385/2025-2026:Fabricating, supplying and fitting Stainless steel letters (English or Malayalam) to the name board with bolt and nuts, drilling and fixing to the panel with synthetic resin adhesive to correct lines and levels as per the direction of the departmental engineers. Letters made of 0.8mm Stainless Steel sheet, having a height of 250mm and a projection of 25mm from the base.

OD284710/2025-2026:Providing and fixing heavy duty folding grab bars at physically handicapped toilets as per manufacturers specification and direction of engineer in charge

OD284711/2025-2026:Providing and fixing heavy duty grab rail at physcally handicapped toilets as per manufacturesspecification and direction of engineer - in -charge

Appendix B - Water Supply and Sanitary(Civil work)

17.2.1:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.1.1:Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.5.3:Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:Range of three half stall urinals with 10 litre PVC. automatic flushing cistern

17.7.2:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

17.32.2:Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

50.17.1.3:Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.4:Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

22.5:Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

OD201976/2025-2026:Providing and filling mixture of coarse sand and stone aggregate of size varying from 20 to 40 mm.

18.52.1:Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1:Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.51.1:Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

50.17.1.1:Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

18.7.2:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal dia pipes

18.7.3:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal dia pipes

18.7.6:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal dia pipes

18.7.4:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal dia pipes

50.18.8.3.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

50.18.8.6.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2

50.18.8.7.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

18.8.2:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal dia pipes

18.18.3:Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

18.17.1:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.3:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

50.18.8.9.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.17.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.18.1:Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.19.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

OD201975/2025-2026:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.160 mm dia 6Kgf/cm2

50.18.9.20.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.2:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

50.18.9.20.3:Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Door Elbow

50.18.9.20.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.20.5:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee

50.18.9.20.6:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee

50.18.9.22.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.3:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.6:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.11:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.12:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.9.22.8:Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.22.10:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

OD201972/2025-2026:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Y

OD201969/2025-2026:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160x110 mm dia Reducer

OD201974/2025-2026:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia 45 degree Elbow

OD201973/2025-2026:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 160 mm dia Tee

OD201968/2025-2026:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia Elbow

Appendix E - Partition works(Civil work)

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

21.2.2:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.2:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm)

Appendix H - Septic Tank & Sump(Civil work)

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

OD285943/2025-2026:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping concrete to site of laying , but excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in -charge.(Note:- cement content considered in this item is @ 330 kg /cum).All work upto plinth level. (Excess/less cost of cement as per mix design is not payable or recoverable)

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1:Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.9.1:Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

19.7.3.1:Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 120x 90 cm and 90 cm deep including C.I. cover with frame ( heavy duty ) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg ( weight of cover 108 kg and weight of frame 100 kg)With common burnt clay F.P.S. ( non modular) bricks of class designation 7.5

19.18.3:Supplying and fixing C.I with out frame for manholes:560 mm diameter ( heavy duty) the weight of the cover to be not less than 108 kg

OD201977/2025-2026:Supplying and erecting 1.20 m diameter concrete ring in each having a depth of 30 cm for well including cost of materials, erection charges without causing any tilt or shift, all labour charges etc complete

LAN and WiFi Main Items(Electronics Work)

OD225906/2025-2026:Supply, Installation, testing and Commissioning of 24 port managed Switch having 24x 10/100/1000BASE-T RJ45 Ports, 4x SFP+ ports, Bandwidth: 128 Gbps or more, 16K MAC, 256 VLANs, Jumbo frame support (bytes): Up to 10K packet size or more, 512MB RAM or higher , Packet forwarding rate: 83.52 or higher, including all other accessories Approved Make: Allied Telesis, Cisco, Juniper, HP, Aruba ,Ruckus, Netgear

OD225348/2025-2026:Supply and Installation of Layer 2 Manageable 24 port Ethernet Switch having 24 x10/100/1000 Mbps + minimum 2 x GbE SFP ports, 52 Gbps bandwidth, 256 or more VLANs and 16K MAC address, supporting ipv6, Priority levels up to 8 hardware queues, up to 9216 Jumbo frames, AC 230V power input, 3 year warranty. Approved Make: Allied Telesis, Aruba, Brocade, Cisco, Fortinet, HP, Juniper, Netgear, Ruckus

OD225352/2025-2026:Supply and Installation of Layer 2 Managable 24 or more port POE+ Ethernet Switch having 24 x 10/100/1000 Mbps + minimum 2 x GbE SFP Auto-sensing Gigabit ports (Power 190W or more) ports, 52 Gbps bandwidth, supporting ipv6, Priority levels up to 8 hardware queues, up to 9216 Jumbo frames, VLAN support, AC 230V power input, 3 year warranty. Approved Make: Allied Telesis, Cisco, Juniper, Aruba, Ruckus, Netgear

OD226086/2025-2026:Supply, Installation, Testing and Commissioning of Single Mode/ Multi Mode 1G Duplex SFP Module Accepted Make: Same make as Network Switch Above

OD226830/2025-2026:Supply, Installation, Testing and Commissioning of SC/LC-LC duplex patch cord 1 meter Preferred Make: Commscope, Molex, R&M, Sterlite or equivalent

OD226095/2025-2026:Supply and installation of WiFi-6 access point having Max data rate up to 5GHz: 2400Mbps 2.4GHz: 600Mbps, Antenna : 2x2 MIMO, Radios, WiFi standards :5GHz: 802.11a/n/ac/ax 2.4GHz: 802.11b/g/n/ax, Max number of active devices : min 50+users up to 256 client devices, support up to 3Gbps speed, Power: POE and 12VDC.including all mounting accessories. Preferred make: Aruba, Netgear, Cisco, Fortinet, Juniper

OD226841/2025-2026:Supply, Installation and fixing of UL Certified CAT-6 Information Outlet for 1000Mbps having spring shutter / dust cover angled face plate + Single RJ45 Keystone sockets in the existing CMS/PVC Box/ GI Box, including termination charges etc. Approved Make: Actassi, Belden, Molex, Panduit, R and M, Systimax

OD226842/2025-2026:Supply, Installation and Fixing of UL Certified CAT-6 information outlet for 1000Mbps having spring shutter / dust cover dual angled face plate, two numbers of RJ45 keystone sockets in the existing CMS/PVC Box/ GI Box, including termination charges etc. Approved Make: Actassi, Belden, Molex, Panduit, R and M, Systimax

OD226850/2025-2026:Supply and providing 3Mtr LSZH CAT-6 Giga UTP patch cord. Preferred Make: Actassi, Belden, Panduit, R&M, Molex or equivalent

CCTV Main Items(Electronics Work)

OD227043/2025-2026:Supply and Installation of Project series Network Video Recorder, support 64 Channel, Should support 12 MP or more resolution IP Camera, Network Bandwidth incoming 640 Mbps and outgoing 640 Mbps for access, support for H.265+/H.265/H.264 encoding format streaming access and decoding output, Recording resolution up to 12MP, Motion detection, Support min. 8 SATA HDDs , Each port supports min. 18TB HDD(Enterprise class),support-RAID0, RAID1, RAID5, RAID6, RAID10,Support dual Gigabit Ethernet ports, Supports 4 HDMI outputs, Min 2 USB ports, Alarm Input/out:16 in /4 out ,Audio:1 in / 1 out , Supports intelligent analytics such as facial detection, Pedestrian Detection, human detection, vehicle detection, License plate recognition, perimeter intrusion, and line crossing statistics, Certification: BIS,CE,FCC,ROHS ,ISO 9001; Preferred make: Honeywell, Bosch, Axis, Pelco, CP Plus, Matrix.

OD227051/2025-2026:Supply, Installation, Testing and Commissioning of STQC approved 5MP IP Varifocal Bullet Camera, Image Sensor: 1/2.7 inch, Progressive CMOS scan, Motorized Lens: 2.8 to 12mm, Resolution: 2880 x1620 or Higher, IR Distance: 50 Meter or more, Min illumination 0.004lux, Video Compression: H.265+; H.265; H.264+; H.264; H.264B; Video Streaming: Triple-Stream(Main/Sub/Third) or more; ONVIF (Profile S/Profile G/Profile T), Motion detection, Face Recognition, Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, Advance features: Starlight, WDR(120dB),Micro SD Card Slot up to 256GB or more, Alarm I/O-1/1, Audio I/O 1/1, ICR auto switch, Power Source: 12V DC/PoE, Casing: Metal ,Weatherproof Standard: IP67, Certification: BIS-ER,CE,FCC,ROHS ,ISO 9001, Approved Make: Honeywell, Bosch, Axis, Pelco, CP Plus, Matrix

OD227052/2025-2026:Supply, Installation, Testing and Commissioning of STQC approved 5MP IP vandal Dome Camera having Image Sensor: 1/2.7 inch, Progressive CMOS scan, Lens: 3.6/2.8 mm fixed lens Resolution: 2592 ×1944 or Higher, inbuilt mic, IR Distance: 30 Meter or more. Min illumination 0.003lux or less, Video Compression: H.265+, H.265, H.264+, H.264, H.264B, MJPEG ,Video Streaming: Triple-Stream(Main/Sub/Third) or better, Motion Detection , ONVIF (Profile S/Profile G/Profile T), Face Recognition, Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, WDR(120dB), Micro SD Card Slot up to 256GB or more, ICR auto switch Power Source: PoE Casing: Metal, Weatherproof Standard: IP67, IK10 ; Certification: BIS,CE,FCC,ROHS ,ISO 9001 ; Approved make: Honeywell, Bosch, Axis, Pelco, CP Plus, Matrix.

OD227058/2025-2026:Supply, Installation, Testing and Commissioning of STQC approved 5MP IP Bullet Camera with inbuilt mic Image, Sensor: 1/2.7 inch Progressive CMOS scan, Lens: 3.6mm fixed lens Resolution: 2592 ×1944 or Higher, IR Distance: 30 Meter or more. Min illumination 0.003lux @ F1.6(AGC ON),Video Compression: H.265+, H.265, H.264+, H.264, H.264B ,Video Streaming: Triple-Stream(Main/Sub/Third) or more stream, Motion Detection , ONVIF (Profile S/Profile G/Profile T); Face Recognition, Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, , WDR(120dB),Micro SD Card Slot up to 256GB, ICR auto switch Power Source: 12V DC/PoE Casing: Metal ,Weatherproof Standard: IP67, Certification: BIS-ER,CE,FCC,ROHS ,ISO 9001:20015; Approved Make: Honeywell, Bosch, Axis, Pelco, CP Plus, Matrix.

OD227059/2025-2026:Supply and Installation of 10 TB Surveillance Hard Disk Drive. Preferred Make: Barracuda, Seagate, WD or equivalent

OD247553/2025-2026:Supply and Installation of Layer 2 Manageable 28 port POE+ Ethernet Switch having 24 x 10/100/1000 Mbps + minimum 4 x GbE SFP Auto-sensing Gigabit ports (Power 380W or more) ports, 56 or more Gbps bandwidth, Packet forwarding rate: 41.67 Mpps, supporting ipv6, Priority levels up to 8 hardware queues, up to 9216 Jumbo frames, VLAN support minimum 255 numbers, AC 230V power input, 3 year warranty. Approved Make: Allied Telesis, Cisco, Juniper, Aruba, Ruckus, Netgear

OD247554/2025-2026:Supply and Installation of Layer 2 Managable 24 port POE+ Ethernet Switch having 24 x 10/100/1000 Mbps + minimum 2 x GbE SFP Auto-sensing Gigabit ports (Power 380W or more) ports, 52 Gbps bandwidth, supporting ipv6, Priority levels up to 8 hardware queues, up to 9216 Jumbo frames, VLAN support, AC 230V power input, 3 year warranty. Approved Make: Allied Telesis, Cisco, Juniper, Aruba, Ruckus, Netgear

OD247603/2025-2026:Supply and Installation of 1G duplex SFP module Accepted Make: Same make as Network Switch above

OD247582/2025-2026:Supply and fixing 19 inch, 9U wall mount Network Rack with ACDB 6 port, Slot Rack Mount Cable Manager Duct, 2 Fan etc. Preferred Make: D-Link, HCL, Netrack, President, Valrack or equivalent.

OD247585/2025-2026:supply, Installation, Testing and Commissioning of wireless mouse with receiver including required length USB cable to keep the receiver outside of the rack.

OD247587/2025-2026:Supply and Installation of 10 Meter or more HDMI Cable (4K@30Hz) Preferred Make: Honeywell, NT or equivalent

OD247593/2025-2026:Supply, Installation, testing and Commissioning of 4K UHD 50 inch Display having Resolution: 3840x2160, Brightness: 350 nits or better, Contrast Ratio:4000:1 or better, Operation Hour: 16/7 , Signage support, 3 HDMI or more, 2 USB or more, 2x10W Speaker, including all other accessories includes wall mount kit capable of tilting ( Revolving Type) etc., Approved Make: LG, Samsung, Sony, Panasonic

OD247599/2025-2026:Supply and installation of weather proof and water proof 4x4 square PVC Junction box for camera.

OD247600/2025-2026:Supply and Installaion of Camera Housings Dimensions : 165.1 x 120.7 x 295.3 mm or equivalent dimensions for out side cameras including accessories for mounting etc.

Telephone Exchange Main Items(Electronics Work)

OD263125/2025-2026:Supply, Installation, Testing and Commissioning of Hybrid IP-PBX System Having 12 Universal slots for mixing analog, digital, GSM/4G,PRI, and VoIP interface cards, minimum 56 analog Extensions( Maximum Analog Subscribers(SLT):240), Minimum 4 Trunks Line (Supports more than 50), Minimum 2 Digital Keyphone Extensions(Supports more than 10), IP Card that supports more than 64 Concurrent calls or above, Expansion License if required, Supports more than 32 SIP Trunk, Supports IP Calls more than 20, minimum 2 ethernet ports, Compliances: EMI/EMC , FCC, EN etc., Approved Make: Matrix, Cisco. NEC, Avaya, Mitel, Coral

OD263127/2025-2026:Supply, Installation, Testing and Commissioning of additional 16 Trunk Lines (Total 20) or 20 SIP Trunk to the existing System (As per the Site Requirement)

OD263128/2025-2026:Supply, Installation, Testing and Commissioning of Digital Keyphone having 240x64 Pixels Graphical LCD with Backlit LED for Incoming/Ongoing Call, Mute and Hold Intuitive User Interface with Icons Caller ID with Name and Number, 1 x RJ9 Handset Port, minimum 4 programmable context sensitive keys, Call Hold Mute Do Not Disturb, Speed Dial, Hotline, Redial, Call Back Auto Answer, Call Forward, Call Waiting, Call Transfer, Room Monitoring, Conference Directory, Call Logs, Paging Dial-by-Name, built in minimum 16 DSS Keys for feature line and extension, ringer lamp, Adjustable desk stand, Volume adjust keys, Full Duplex Speaker Phone, Mounting accessories, Certification: CE, RoHS, FCC etc., Approved Make: Cisco, Matrix, NEC, Alcatel

OD263129/2025-2026:Supply, Installation, Testing and Commissioning of Corded Landline Phone having 3 line LCD Display, Hands Free Speakerphone, Caller ID, 20 OneTouch/ 10 Speed Dialer, 20 Redial Memory/ Auto Redial, Ringer Indicator, Electronic Hold on Music, Mute, On-Hook Dialing, Call Restriction, 50 Phonebook Name Input , Black, etc., Approved make: Beetel, Panasonic, Alcatel, NEC, Avaya

OD263130/2025-2026:Supply, Installation, Testing and Commissioning of Corded Landline Phone having Ringer Volume Control, flash, pause, and redial buttons, Compact Wall Mountable for using kitchen and restaurant

OD264022/2025-2026:Supply and fixing of UL Certified Information Outlet with spring shutter/ dust cover face plate+ one number of RJ11 jack including termination. Approved Make: Actassi, Belden, Panduit, R&M, Molex, Systimax

OD264023/2025-2026:Supply, Installation, Testing and Commissioning of Door type junction boxes with lock and fitted with Krone make modules for 100pair

OD267890/2025-2026:Supply, Installation, Testing and Commissioning of Door type junction boxes with lock and fitted with Krone make modules for 30 pair

OD264024/2025-2026:Supply, Installation and fixing of Door type junction boxes with lock and fitted with Krone make modules for 20 pair

OD264025/2025-2026:Supply and fixing of door type junction boxes with lock and fitted with Krone make modules for 10 pair

1.18.2:Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

OD267971/2025-2026:Supplying and drawing 20 Pair FRLS PVC insulated annealed copper conductor, telephone cable in the existing surface/ recessed steel/ PVC conduit as required

OD267977/2025-2026:Supplying and drawing 10 Pair FRLS PVC insulated annealed copper conductor, telephone cable in the existing surface/ recessed steel/ PVC conduit as required

Video Conferencing(Electronics Work)

OD250563/2025-2026:Supply, Installation, Testing, Commissioning and Training of 65 or Higher inch 4K Interactive Display having Resolution: 3840×2160 (UHD), Contrast ratio ( typical): 1200:1, Brightness (typical): 400cd/m2 or better, Aspect ratio 16:9, Operation hours: 16/7, Viewing Angle (H/V): 178:178, Glass protection, LED Back Lit or better, Response time less than or equal to 8 ms, System memory: minimum 4GB RAM, System storage: Minimum 32 GB, Processor, Connectivity: HDMI(3), USB 3.0, USB 2.0, USB Touch Out, Audio Out, RJ45, Built in OPS Slot, 20 point multi touch white boarding, Screen Share, WiFi, Bluetooth, Accessories include USB (Touch) cable, HDMI cable, Touch Pen, Remote Control with Battery, Wall Mount Kit etc. Approved Model: BenQ, LG, Samsung, NEC, View Sonic

OD264043/2025-2026:Supply, Installation, Testing and Commissioning of OPS for Interactive Display having Intel Core i5, 13th Gen, Windows 11 Pro Operating System, Certified with BIS, ISO, CE, FCC, and RoHS , 8/16 GB RAM, 512 GB SSD, 2 x USB 3.0, 2 x USB 2.0, 1xHDMI Preferred Make: BenQ, Asus, Lenovo or Equivalent

OD250726/2025-2026:Supply, Installation, Testing and Commission of POE Enabled PTZ camera 20x Zoom 4K and 30x Zoom Full HD output, High-quality glass lens, 20x optical zoom and 60.38 degree horizontal field of view, Output: HDMI, USB 2.0 ( 2160p30) and IP, USB Output: USB 2.0 ( 2160p30 max.), Resolution Up to 4K30, Sensor: Sony 1/2.8?,8.42MP, 16:9 High SNR CMOS Sensor, Shutter: Auto/ Manual, Scanning mode: Progressive, Backlight Compensation, Digital Noise Reduction, Signal Noise Ratio greater than 50 dB., Horizontal FOV: 68.5 ~ 4.0 degree, Vertical FOV: 40.5° ~ 2.0°, Horizontal rotation: -170 ~ +170 degree, Vertical rotation: 120 degree , pan speed range: 0.15° ~ 120° p/s, Number of presets: up to 255, Control: UVC, IR Remote, IP. control protocol: VISCA over IP, Network interface: RJ45 100 mbit, Hybrid Tracking, Presenter Tracking with required mounting bracket and other accessories etc., Approved Make: Kramer, Avonic, Lumens, Yealink, Aver, Panasonic

OD264042/2025-2026:Supply, Installation, Testing and Commissioning of HDMI to USB 3.2 Gen 1 Video Capture Tool with Loop-Out, Conversion of HDMI 2.0b 18Gbps signals to 5Gbps, USB 3.2 Gen1 data, HDMI 4K 60Hz input with 1080p 60Hz downscaling support, Uncompressed YUV2 when using USB 3.2, MJPEG compression for USB 2.0., Compatible with VLC, OBS, XSPLIT, AMCAP and other video capturing software, Ideal for video conferencing, online streaming and other HDMI video capture scenarios. Approved Make: Purelink, Kramer, Crestron, Extron, Biamp

OD267484/2025-2026:Supply, Installation, Testing and Commissioning of USB 3.2 USB-C Cable with E-Marker of minimum 2.00meter length having USB 3.2 (Gen 1x2) 10Gbps data transmission. Gold plated precision contacts. USB-C male to USB-C male. High purity copper conductors and triple shielding. E-Marker, USB Power Delivery 100W, DP Alt-Mode up to 8K 30Hz. etc. Approved Make: PureLink, Kramer, Crestron, Biamp, Extron

OD267488/2025-2026:Supply and laying of Certified minimum 2 meter 4K Premium High Speed HDMI Cable having HDMI version 2.0 of 18Gbps for resolutions up to 4K UltraHD 60Hz. Gold plated precision contacts . HDMI-A male to HDMI-A male. High purity, tinned OFC copper conductors and triple shielding, AWG28. Approved Make: Purelink, Kramer, Crestron, Extron, Biamp

OD267491/2025-2026:Supply and Installation of Wireless Keyboard and Mouse including wireless receiver having Spill-Resistant Keys etc., Approved Make: Dell, HP, Logitech

OD267557/2025-2026:Supply, Installation, Testing and Commissioning of 5-meter USB 3.2 Gen 1 extender cable designed to extend the distance of a single USB device up to 5 meters while delivering high-speed data transfer rates of up to 5 Gbps. It supports USB 3.2 Gen 1 standards and is backward compatible with USB 2.0 and 1.1 for reliable communication. The cable features a builtin USB hub IC that fully supports hot swapping for various USB devices, ensuring seamless connectivity. It offers multiplatform support for Windows and macOS, requires no additional software installation (plug-and-play), and operates without external power for most devices Preferred Make: Aten, Kramer, Purelink or equivalent

OD267638/2025-2026:Supply, Installation, Testing and Commissioning of 6 Channel Mixer having minimum 6 mic/line inputs and 1 unbalanced stereo input, 2 balanced outputs and 1 unbalanced stereo output, USB audio input/output (1 stereo input, 1 stereo output),echo canceler (AEC) for each input channel, Noise cancellation that can be assigned to any output channel, Built-in 4-band EQ or better , Eight 8-band or better feedback suppressors , Audio input/output settings can be configured, S/N Ratio: 90 dB or higher, Phantom Power:+48V DC, RJ45 port, including accessories connector, Rack Mount Kit etc., Approved Make: Audio Technica, Kramer, Yamaha, QSC, ClearOne

OD250722/2025-2026:Supply, Installation, Testing and Commissioning of 2 way wall mount speaker with 4 inch LF and 1 inch HF, bass reflex port, dedicated wall bracket, ABS moulded enclosure, Power handling 30W/40W , imp 8 Ohm, Freq. Res.90Hz ~ 20kHz, ± 6dB, MAX SPL 102dB ( Direct), sensitivity 88 dB (half space),2.5W, 5W, 10W, 20W power taps @100V, IP65 etc., including mounting bracket and other accessories Approved Make: Audac, Apart, QSC, JBL, RCF, Sonodyne

OD250723/2025-2026:Supply, Installation, testing and commissioning of 120 watts power amplifier at 100 volt or 4 ohm with Rear panel volume control, Balanced input and thru out, Frequency Response 55Hz - 20kHz, THD+N less than 0.2% (-3dB), Signal to Noise Ratio greater than 85dB, Input Sensitivity 160mVrms, short-circuit, over-load, and thermal protection, Fan cooled Approved Make: Audac, Australian Monitor, TOA, Apart, RCF, Yamaha

OD267449/2025-2026:Supply, Installation, Testing and Commissioning of Gooseneck Microphone with Desk Stand having Cardioid Polar Pattern, Frequency Response: 30 - 20,000 Hz, Maximum SPL: 135 dB (1 kHz, 1 percentage THD), XLR Analog Output, Phantom Power, Stand Having XLR input and output, Ultra-Quiet Electronic Switch on/off control, LED mic status indicator, Diecast metal construction, non-slip bottom pads etc.,. Approved Make: Audio Technica, Shure, Bosch, AKG, Beyerdynamic, Sennheiser

OD267362/2025-2026:Supply, Installation, Testing and Commissioning of 4-channel receiver having Each receiver channel can be paired with up to four transmitters, Operating Frequencies: 2,402 to 2,480 MHz or equivalent, Dynamic Range 120 dB, Total Harmonic Distortion less than .05 percentage, Monitor transmitter status, audio level, remaining battery time, Encryption Method: AES128, Digital 24-bit/48 kHz wireless operation for ultimate sound quality, External Antenna, Rack mounting Accessories, AC adapter , etc., Approved Make: Audio Technica, Shure, Bosch, AKG, Beyerdynamic, Sennheiser

OD265592/2025-2026:Supply, Installation, Testing and Commissioning of desk stand transmitter to support gooseneck microphone with RF Output Power 10mW, RF Sensitivity -90 dBm, Antenna True diversity, Phantom Power Supply DC24V, Built-in Battery 3.7 V/1,460 mAh or better lithium-ion battery, USB Charging port including accessories USB adapter, cables etc., Approved Make: Audio Technica, Shure, Bosch, AKG, Beyerdynamic, Sennheiser

OD265593/2025-2026:Supply, Installation, Testing and Commissioning of double-gooseneck permanently polarized condenser cardioid microphone with Frequency Response 70-16,000 Hz, Open Circuit Sensitivity -37 dB (14.1 mV) re 1V at 1 Pa, Maximum Input Sound Level 134 dB SPL, 1 kHz at 1 percentage T.H.D., Dynamic Range 106 dB, 1 kHz at Max SPL, S/N Ratio 66 dB, 1 kHz at 1 Pa, Phantom Power Requirements 9-52V DC, 2 mA typical etc. Approved Make: Audio Technica, AKG, Beyerdynamic, Sennheiser, Shure

OD267388/2025-2026:Supply, Installation, Testing and Commissioning of Wireless Handheld Microphone Transmitter having RF Sensitivity: -90 dBm or better, RF Output Power: 10mW or better, True diversity Antenna, Dynamic Hypercardioid Microphone, including accessories Mic holder, Battery etc., Approved Make: Audio Technica, Shure, Bosch, AKG, Beyerdynamic, Sennheiser

OD267451/2025-2026:Supply, Installation and fixing of 2 core Sheilded PVC Insulated Microphone cable with Ultra low Capacitance 60(Pf/m) ; Outer Jacket : PVC Matt; Working Temperature: 20 °C / +70 °C ; Diameter : 6.5mm; extreamly flexibel as per the tender specifications. Preferred Make: Belden, Klotz, Gotham or equivalent.

OD267818/2025-2026:Supply, Installation and Fixing of EP/Phono/RCA connectors Preferred Make: Neutrik or equivalent or higher

OD267819/2025-2026:Supply, Installation and Fixing of XLR Jack connectors (XLR M/F as per site requirements) Preferred Make: Neutrik or equivalent or higher

OD267858/2025-2026:Supply and Laying of 2 core 2.5 Sq.mm Speaker Cable with No of Strands 80, Annealed Tinned Copper, Insulation Resistance - 10000 MΩ at DC 125 V, etc Approved Make: Krystal, Belden, Klotz, Gotham

OD250727/2025-2026:Supply and Installation of 19", floor standing 22U or more audio Rack with four numbers of Caster wheels and having Accessories like 4nos of supporting trays, 4 no's of cooling fan, power strip with spike arrester for 7 sockets(min). Preferred Make: Dlink, Legrand, Netrack, President, Valrack or equivalent

Cable TV and other Accessories(Electronics Work)

OD248552/2025-2026:Supply, Installation and commissioning of minimum 50 inch or more Commercial UHD TV having 4K Display, LED backlight, Resolution 3840 x2160, 16/7 operation, HDR (High Dynamic Range), 2 Channel Speakers, Connectivity: USB, HDMI, LAN, WiFi 5 or above, RF in, Smart TV features, Screen Mirroring support, Web Browser, display USB content on TV, Remote control with battery, wall mount kit capable of tilting to all angles( Revolving Type) and OEM warranty for 3 years. Accepted Make: LG, Panasonic, Samsung, Sony.

OD248544/2025-2026:Supply, Installation and commissioning of minimum 43 inch or more UHD Smart TV having 4K Display, Backlight: Direct LED, Operation Time: 16/7, Resolution 3840 x2160, HDR (High Dynamic Range), Brightness: 350 cd/m² or more, Viewing Angle: 178x178, Audio Power Output: 10W + 10W or more, Connectivity: USB, HDMI, Composite Video Input, Ethernet, WiFi or above, , Remote control with battery, wall mount kit capable of tilting ( Revolving Type) and OEM warranty for 5 years. Accepted Make: Sony, Panasonic, Samsung, LG

OD248546/2025-2026:Supply, Installation, Testing and Commissioning of Cable TV/Dish TV with minimum 3 months Subscription and required installation accessories to support minimum 20 number of TVs in the building that includes Splicing Box, Splitter, Converter etc

OD248547/2025-2026:Supply, Installation, Testing and Commissioning of Set Top Box Shelf/Stand having Wall Mounted, durable, rust proof, material: wooden/ Glass or better material, Should have enough space to keep the set top box and 2 remote control or (minimum 30cm length and 22cm width) and other mounting accessories etc.,

OD248550/2025-2026:Supply and Installation of Wall mount faceplate for Cable TV in the existing surface/recess mount box having ABS or better material , that is sturdy, tough and durable. Preferred Make: Legrand, ABB or equivalent.

OD248551/2025-2026:Supply, Installation and Fixing of Coaxial F Connector in the existing faceplate have Corrosion-Resistant material , stability of signal transmission and durability.

1.19:Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

OD248843/2025-2026:Supply and fixing 19 inch, 9U wall mount Network Rack with ACDB 6 port, minimum 2 rack mountable Tray, 2 Fan etc. Preferred Make: D-Link, HCL, Netrack, President, Valrack or equivalent.

Common Passive Items(Electronics Work)

OD267978/2025-2026:Supply, Installation, Testing and commissioning of 27U floor mount Server Rack with minimum 2 fans, 4 heavy duty castor wheels, minimum 3 numbers of 22 slot rack mount horizontal cable managers, toughened glass door, hardware kits, 6 port PDU, minimum 1 rack mount trays, etc. Preferred Make: APC, Legrand, Netrack, Rittal, Vertiv or equivalent

OD267979/2025-2026:Supply and fixing 19 inch, 15U wall mount Network Rack with ACDB 6 port, minimum 2 numbers of Slot Rack Mount Horizontal cable manager duct, 2 Fan etc. Preferred Make: D-Link, HCL, Netrack, President, Valrack or equivalent.

OD248462/2025-2026:Supply and fixing 24 port Enhanced CAT-6, unloaded rack mountable modular type Patch Panel as per EIA/TIA-TSB 40A specification for interconnecting servers and clients, including termination charges. Preferred make: Actasi, Belden, R&M, Molex or equivalent

OD248461/2025-2026:Supply, Installation, Testing and Fixing of UL Listed CAT6 Keystone for existing patch panel Preferred make: Actassi, Belden, Systimax, R&M, Molex or equivalent

OD248460/2025-2026:Supply & providing 1Mtr LSZH CAT-6 Giga UTP patch cord Preferred Make: Actassi, Belden, Panduit, R&M, Molex or equivalent

OD267999/2025-2026:Supply and Installation of 19 inch 6 port rack mountable 1U size complete Steel housing fully powder coated Light Interface Unit (LIU) having FR grade Nylon Cable grommets, ABS Splice Trays with fully cushioned splice holder containing grooves for fixing splice protection sleeves, Cable Spools made up of flame retardant plastic, high impact resistance, stackable design for providing sufficient room for storage of excess cables, Blanking plates, adapter plates etc. Approved Make: Actassi, AFL, Belden, Molex, Panduit, R and M, Sterlite, Systimax

OD268576/2025-2026:Supply and Installation of 19 inch 12 port rack mountable 1U size complete Steel housing fully powder coated Light Interface Unit (LIU) having FR grade Nylon Cable grommets, ABS Splice Trays with fully cushioned splice holder containing grooves for fixing splice protection sleeves, Cable Spools made up of flame retardant plastic, high impact resistance, stackable design for providing sufficient room for storage of excess cables, Blanking plates, adapter plates etc. Approved Make: Actassi, AFL, Belden, Molex, Panduit, R and M, Sterlite, Systimax

OD268000/2025-2026:Supply, Installation, Testing and commissioning of SC Duplex single mode adapter connected through 2 pigtails and spliced it to the existing Fiber in the existing LIU (splicing charges included), etc. Approved Make: Actassi, AFL, Belden, Molex, Panduit, R and M, Sterlite, Systimax

OD248505/2025-2026:Supply, Installation, Testing and Commissioning Secured Wall Mount Fiber Box having (12/24/48) Port LIU minimum 12 SC port loaded, maximum supporting 24 SC Ports, Fully secured with lockable and secured steel doors, 6 colored pigtails for core identification, Material: cold Rolled Steel, Min thickness: 1.2mm, Black powder coat, Multiple entry points with Nitrile Butadiene rubber (NBR N240), Fiber Termination, RoHs Complaint, should include global hardware kit, splice Trays, glands and blank inserts to cover unused ports as required Approved Make: Actassi, Belden, Molex, R and M, Panduit, Systimax

OD268041/2025-2026:Supply and Installation of 6 Core Single Mode Low Water Peak Outside plant (OSP) OFC having LSZH sheath, conforming to ITU-T G.655, IEC 60794-1 : 2001, IS 13882 (Part 1/Sec 1) : 1999 etc. Preferred Make: AFL, Commscope, Molex, R and M, Sterlite.

OD215822/2025-2026:Supply, drawing, testing and commissioning of UL certified of UTP 4 pair LSZH CAT 6 LAN cable 23 AWG and conforming to the standards ANSI/TIA-568.2-D, ISO/IEC 11801, IEEE802.3, ISO/IEC 60332-1, ISO/IEC 61034-2, ISO/IEC 61754-2, Colour Code as per TIA/EIA 568-B, RoHS Compliant, transmission performance tested up to 500 MHz or better and Insertion Loss/ Attenuation: 33 dB/100m or better at 250 MHz in the existing surface/recessed steel/PVC conduit Approved Make: Actassi, Belden, Panduit, Molex, R and M, Systimax .

OD227018/2025-2026:Supply, Installation and Fixing of 1 or 2 module GI box (75mm x 75mm x 60mm deep) on Recess including making good the damages, etc as required.

OD227017/2025-2026:Supply and fixing of UL certified 1 or 2 module PVC Box on Surface/Recess including making good the damages, color washing, etc. as required Approved Make: Actassi, Belden, Molex, Panduit, R and M, Systimax

90.9.2.12:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.1 to 3 module mounting box

90.9.2.1:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

90.9.2.10:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Joint cover

90.9.2.5:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Internal angle 90 degree

90.9.2.8:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.End cap

4.1.3:Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 225 mm width X 50 mm depth X 1.6 mm thickness

1.21.1:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

OD268122/2025-2026:Supply, Installation and fixing of Equipotential bonding rail light duty to maintain an equal earth potential meets the requirement for IS/IEC-62305

5.19:Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

5.2:Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt) as required

5.7:Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

OD268228/2025-2026:Supply, Installation, Testing and Commissioning of 3KVA or more Pure sine wave online double conversion UPS with 4600 VAH or more SMF battery back up on full load, Efficiency 90% or more (full load), short circuit protection, Suitable rack for keeping the Battery. Warranty 3 year for UPS and minimum 2 year for battery. Accepted Make: APC, Eaton, Emerson, GE, Numeric, Socomec, Delta, ABB

90.6.5.12:Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 2.50 sq mm

OD268313/2025-2026:Supply, Installation, Testing and Commissioning of Power line Surge protection device - OPTION 1( Class B+C) type SPD :This panel should include pluggable type surge arrester in suitable enclosure Class C/ Class 2 as per IEC 61643 (IP 20) , thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E). Nominal discharge current-20 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 40 kA (8/20µ sec)for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth voltage protection level 1400V (L to N) & 1200V (N to E).Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E)DIN rail mounting type etc complete with back up fuse as required and as directed. Approved make : Erico, Raycap , OBO, Weidmuller, L&T

OD268286/2025-2026:Supply and Installation of necessary electrical accessories and required cables for connecting the UPS from main supply and distribution of UPS Power to Network racks ACDB in structured way ( ISI standards), using necessary ELCBs, Isolator, MCB, Sockets in distribution board etc.,

OD268290/2025-2026:Charges for Documentation, Training and preparation of diagram and permanent labelling of Information outlets, audio video devices, Electronic equipment's and Racks , etc.

Electrification(Electrical work)

1.10.3:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

OD234125/2025-2026:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in existing PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated single core copper conductor cable etc as required. Group C

1.31:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

90.3.20.3:Supply & installation of light fittings on TW round block Supply, conveyance installation testing and commissioning the light fittings of following types made of CRCA with 0.5mm thickness complete with all accessories and lamps etc. directly on wall or ceiling with PVC round block neatly painted to suit the fitting and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.1200 mm 1X20W LED Lamp with box type fixture

90.3.24.3:Supply & installation of light fittings suspended on ball & socket arrangement with 19 mm down rod Supply, conveyance, installation, testing and commissioning the light fittings of following types made of .5mm thick CRCA sheet accessories and lamps etc. including supplying and fixing ball and socket arrangements on PVC round block, suspension down rod of 19mm dia MS conduit up to 2x30cm length including painting and wiring the down rod with 16/0.20mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connections etc. a required.1200 mm 1X20W LED Lamp with box type fixture

90.3.24.4:Supply & installation of light fittings suspended on ball & socket arrangement with 19 mm down rod Supply, conveyance, installation, testing and commissioning the light fittings of following types made of .5mm thick CRCA sheet accessories and lamps etc. including supplying and fixing ball and socket arrangements on PVC round block, suspension down rod of 19mm dia MS conduit up to 2x30cm length including painting and wiring the down rod with 16/0.20mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connections etc. a required.1200 mm 2X20W LED Lamp with box type fixture

90.3.10:Supplying and providing extra H.G conduit down rod of 19 mm dia 2 x 1.00 m long with 16/0.20 mm 3 core copper conductor flex wire conforming to relevant ISS or with the extended original wiring and giving connection etc. as required.

OD241869/2025-2026:Supply, conveyance installation testing and commissioning the light fittings of 1800 lumen round/ square(1X1) recessed fitting made of diecast aluminium, having efficacy not less than 110l/w, pf greater than 0.95, THD less than or equal to 10%, Chip makeCree/Osram/lumilled/Nichea and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.

OD243739/2025-2026:Supply, conveyance installation testing and commissioning the light fittings of 2400 lumen round/ square(1X1) recessed fitting made of diecast aluminium, having efficacy not less than 100l/w, pf greater than 0.95, THD less than or equal to 10%, Chip makeCree/Osram/lumilled/Nichea and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.

OD294150/2025-2026:Supply Installation Testing and Commissioning of 3600 lumen square(2ft X 2ft) recessed fitting made of diecast aluminium body, polycarbonate diffuser, having efficacy not less than 110l/w, pf greater than 0.95, THD less than or equal to 10%, (UGR less than 19) all types complete with all accessories in the existing opening of false ceiling, giving connections with the existing wire etc. as required. Chip make Cree/Osram/lumilled/Nichea Make- Philips Cool White Recessed Troffer G6 LED Panel Light or equivalent.

OD241978/2025-2026:Supply, conveyance installation testing and commissioning of the LED light fittings of 1800 lumen round/ square surface mount fitting made of diecast aluminium, having efficacy not less than 100l/w, pf greater than 0.95, THD less than or equal to 10%, Chip make Cree/Osram/lumilled/Nichea and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.

OD241979/2025-2026:Supply, conveyance installation testing and commissioning of the LED light fittings of 3600 lumen round/ square surface mount fitting made of diecast aluminium, having efficacy not less than 100l/w, pf greater than 0.95, THD less than or equal to 10%, Chip make Cree/Osram/lumilled/Nichea and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.

OD294147/2025-2026:Supply, installation, testing and commissioning of 1200 mm sweep BEE-5 star rated ceiling fan with brushless direct current motor (BLDC) , class of insulation B , 3 no's blades , 30 cm long down rod , 2no:s canopies, shackle kit, safety rope , copper winding, power factor not less than .9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 cum/min,350 RPM (tolerance as per IS :374-2019, THD less than 10% including remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut and bolts , washers, temperature rise equal to 75 deg Celsius ( maximum) , insulation resistance more than 2 Megaohm , suitable for 230V,50 Hz, single phase AC supply , earthing etc., complete as required:

OD288506/2025-2026:Supply and fixing of safety Bowden with double side locking bolt as required

1.47:Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

90.4.1:Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

OD294148/2025-2026:Supply and fixing cast aluminium stove enameled bulk head fitting with mesh guard heat resistant prismatic glass cover including 9 W LED Bulb to wall / ceiling including giving connections with required length of 16/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and making good the surface as required

OD295306/2025-2026:Supply ,installation, testing and commissioning of 5400 lumen LED, efficacy >=120 Lm/watt, IP 66 street light fitting with die-cast aluminium housing, polycarbonate cover complete with THD <10%, power factor >0.95, RoHS compliant, duly wired up for use on 230 V AC supply, IK >=7, with internal surge protection 4k above. Chip make Cree/Osram/lumilled/Nichea/Bridgelux.(LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

OD295307/2025-2026:Supply ,installation, testing and commissioning of 9000 lumen LED, efficacy >=120 Lm/watt, IP 66 street light fitting with die-cast aluminium housing, polycarbonate cover complete with THD 0.95, RoHS compliant, duly wired up for use on 230 V AC supply, IK >=7, with internal surge protection 4k above. Chip make Cree/Osram/lumilled/Nichea/Bridgelux.(LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

OD295317/2025-2026:Supply Conveyance, installation, testing and commissioning of 50W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer) Philips/ Whipro or equivalent make

OD241871/2025-2026:Supply, installation, testing and commissioning of 200 mm sweep Light Duty Exhaust fan in plastic body with self opening lowers working on 230v single phase A/C supply, fittings with all accessories l and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required.

OD232502/2025-2026:Supply, conveyance, installation , testing and commissioning of 300/305 mm sweep Light Duty Exhaust fan in metal frame working on 230 V A/C in the existing opening, fixing necessary anchor bolts / bolt and nuts etc., as required including giving connections with the supplied wire along with the exhaust fan.

90.4.8:Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

1.21.1:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.17.3:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.6:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 1.5 sq. mm

1.17.9:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.9 x 1.5 sq. mm

1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.15:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 2.5 sq. mm

1.17.18:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.9 x 2.5 sq. mm

1.17.21:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.17.24:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 4 sq. mm

1.17.30:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 6 sq. mm

1.17.33:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 6 sq. mm

90.6.4.53:Supply and drawing 650/1100 V grade FRLS PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.10.00 sq.mm 3 Run

1.24.1:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

90.10.3.14:Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A SP switch with indicator

90.10.3.33:Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A 3pin Shuttered socket

1.27.1:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

90.9.2.1:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

90.9.2.2:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Cable devider

90.9.2.3:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.External angle 90 degree

90.9.2.5:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Internal angle 90 degree

90.9.2.8:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.End cap

90.9.2.10:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Joint cover

90.9.2.11:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.Cable retainer

90.9.2.12:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.1 to 3 module mounting box

90.9.2.13:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.4 to 5 module mounting box

90.9.2.14:Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.8 module mounting box

90.10.1.2:Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )2 module moulded plastic box on surface

1.28.1:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.28.2:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

1.28.4:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module

1.28.5:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module

90.11.1.10:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - three phase double cover (IP 42/43)

90.11.1.11:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43)

90.11.1.14:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

2.3.2:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way, Double door

2.3.4:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 16 way, Double door

2.10.1:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.10.4:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

2.12.1:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.2:Supplying and fixing following rating, double pole, (single phase and neutral),240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.13.1:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.1:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

2.15.2:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

OD244342/2025-2026:Supplying and fixing FP sheet steel enclosure on surface/ recess along with 16/25/32/40/63amps 415 volts 40A 4 pole Isolator complete with connections, testing and commissioning etc. as required.

2.16:Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

OD294134/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 4x25 sqmm (clamped with 1mm thick saddle)

OD294135/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 4x16 sqmm (clamped with 1mm thick saddle)

OD294136/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 4x10 sqmm (clamped with 1mm thick saddle)

OD294137/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 3.5x120 sqmm (clamped with 25/40x3mm MS flat clamp)

OD294138/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on cable tray as required. 3.5x70sqmm (clamped with 25x3mm MS flat clamp)

OD294139/2025-2026:Supply and laying of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS1554(part I)/1988 for PVC & IS7098 (part I)/1988 for XLPE of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. 3.5x70 sqmm

OD294140/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 3.5x185 sqmm (clamped with 25/40x3mm MS flat clamp)

OD294141/2025-2026:Supply and laying of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS1554(part I)/1988 for PVC & IS7098 (part I )/1988 for XLPE of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. 3.5x185 sqmm

9.1.27:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.23:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.25:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.34:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.32:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

90.12.9.4:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench77/63 mm or nearest size

5.9:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

5.15:Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

OD294143/2025-2026:Providing and drawing 2.65 mm(12 SWG) copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

OD294144/2025-2026:Providing and drawing 3.15 mm (10 SWG) copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

OD294145/2025-2026:Providing and drawing 4.0 mm (8 SWG) copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

90.16.5.4:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

90.16.5.2:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG)

90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

OD271006/2025-2026:Supply, conveyance and fixing the following types & current rated control gears & switchgears Conforms to IS/IEC 60947-2 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.200A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL and 60-100% SC (L&K make DN2-250D or equivalent)

90.14.10.3:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.14.10.1:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 3 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.14.10.11:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.125A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

OD291008/2025-2026:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.200A, 4 pole, current limiting type MCCB with Isolation duty

OD290964/2025-2026:supply and fixing of multi function meter to read VA,PF,KW,KWh, accuracy class-1 LCD with necessary connected item as required

OD297385/2025-2026:Supply and providing Cable alley, 100 x 40 mm aluminium anodised legend plates in the existing panel board as required.

OD297386/2025-2026:Supply and providing Bus bar chamber, 100 x 40 mm aluminium anodised legend plates in the existing panel board as required.

OD297388/2025-2026:Supply and providing Danger 415 V, 150 x 100 mm aluminium anodised legend plates in the existing panel board as required.

OD297389/2025-2026:Supplying and fixing 2A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

OD297395/2025-2026:Carrying out control wiring for panel with normal meters and indication lamps alone with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/equipments including providing suitable size insulated sockets at the termination points or soldered properly,providing numbering ferules for the proper identification of the wiring, keeping the wiring firm by suitable tie/tie mounts/PVC duct etc as required.1.50sq mm wire single run

OD242633/2025-2026:supply and fixing of Three Phase Voltmeter accuracy class 1 with necessary connected item as required

OD242634/2025-2026:supply and fixing of Single Phase Ammeter accuracy class 1 with necessary connected item as required

OD242635/2025-2026:Supply and fixing of Red, Green, Black, Yellow, Orange colours LED indicator, AC/DC, 22.5 mm cut out dia and its connected accessories as required

OD242636/2025-2026:Supply and fixing of Blue colour LED indicator, AC/DC, 22.5 mm cut out dia and its connected accessories as required

OD232510/2025-2026:Supply, Installation, Testing and commissioning of 200/5 A, 5 VA, accuracy class 1, Resin Cast Metering CT as required

OD297397/2025-2026:Supply and fixing 120/5 A, 5 VA, accuracy class 1, Resin Cast Metering CT in the existing panel assembly as required.

90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

OD294142/2025-2026:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & shall conform to relevant IS .Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurements will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)

90.14.2.1:Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.3:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardSupply and providing 'U' section PVC beeding in the panel board

90.14.4:Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

90.14.6:Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7:Supply and providing copper earth bus in the panel board

OD232506/2025-2026:Supplying and fixing 250A, HRC Fuse base with 200A HRC Fuse link with connections, in existing meter board as required.

OD232509/2025-2026:Supply and fixing of 100 A, 2 Way neutral links mounted on DMC/SMC base and its connected accessories as required

OD295386/2025-2026:Supply and providing M8 anchor bolt hook in wall / parapet for binding support for service main

OD241949/2025-2026:Painting letters or figures of the following sizes with enamel paint as identification mark to the fire extinguisher etc. as required. 2.5 cm, 4 cm, 5 cm height

Fire fighting works(Electrical work)

18.1.9:a)Supplying,installation,testing and commissioning of Electric driven Main Fire Pump suitable for Automatic operation and consisting of following, complete in all respect , as required : b) Horizontal type, Multi stage ,centrifugal, split casing Pump of Cast Iron body and bronze impeller with stainless steel shaft ,mechanical seal conforming to IS 1520. C) Suitable HP Squirrel Cage Induction Motor, TEFC, Synchronous speed 1500rpm suitable for operation on 415 V 3 phase 50 HZ AC supply with IP55 Protection for enclosure ,horizontal foot mounted type with class F insulation, conforming to IS 325. d) M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etc as required. e) Suitable cement concrete foundation duly plastered with Anti vibration pads 1620 lpm at 56 m head

18.3.3:a)Supplying, installation, testing and commissioning of Electric driven Pressurisation Pump suitable for Automatic operation and consisting of following, complete in all respect , as required :(Jockey Pump) b) Horizontal type, Multi stage ,centrifugal, split casing Pump of Cast Iron body and bronze impeller with stainless steel shaft ,mechanical seal conforming to IS 1520. C) Suitable HP Squirrel Cage Induction Motor, TEFC type suitable for operation on 415 V 3 phase 50 HZ AC supply with IP55 Protection for enclosure ,horizontal foot mounted type with class F insulation, conforming to IS 325. d)M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etc as required. e) Suitable cement concrete foundation duly plastered with Anti vibration pads180 lpm at 56m Head

18.2.9:a)Supplying,installation,testing and commissioning of Diesel Engine driven Main Fire Pump suitable for Automatic operation and consisting of following, complete in all respect , as required :(Diesel Driven Pump) b) Horizontal type, Multi stage ,centrifugal, split Pump of Cast Iron body and bronze impeller with stainless steel shaft ,mechanical seal conforming to IS 1520. C) Suitable HP ,1500rpm,water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism 12/24 V Electric starting equipment,diesel tank, exhaust pipe extended upto 10m outside pump house duly insulated with 50 mm thick glass wool with 1 mm thick Al sheet cladding residential silencer, instruments and protection as per standard specifications, stop solenoid for Auto stop in the event of fault with audio indications, painted with post office red colour etc as required. d) M.S Fabricated common base plate coupling, coupling guard ,foundation bolts etc as required. e) Suitable cement concrete foundation duly plastered with Anti vibration pads1620 lpm at 56 m head

OD241174/2025-2026:Supply ,installation ,testing and commissioning of electric driven terrace pump mounted on anti vibration pads consisting of following,complete in all respects as required. a) Horizontal type, centrifugal, End suction pump of CI body & bronze impeller with stainless steel shaft, mechanical seal at a flow of 900 lpm at 35 m Head conforming to IS 1520. b)Suitable HP Squirrel cage induction motor, TEFC type having synchronous speed of 1500 RPM & class- 'F' insulation suitable for operation on 415 V, 3 phase 50 Hz AC supply with IP55 protection for enclosureconforming to IS-325 c)MS fabricated common base plate ,coupling,coupling guard ,foundation bolts etc as required d)Suitable cement concrete foundation duly plastered .

OD296726/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on cable tray as required. 3.5x70sqmm (clamped with 25x3mm MS flat clamp)

OD296756/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 3.5x95 sqmm (clamped with 25x3mm MS flat clamp)

OD296757/2025-2026:Supply ,laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium conductor power cable of 1.1 KV grade conforming to IS 1554/(part I)/1988 for PVC & IS 7098/(part I)/1988 for XLPE of following size on wall surface as required. 4x16 sqmm (clamped with 1mm thick saddle)

9.1.23:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.24:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

OD296762/2025-2026:Providing and drawing 2.65 mm(12 SWG) copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

90.16.5.2:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG)

18.11.2:Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 rating with bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers ,gaskets conforming to IS 13095 of following sizes as required:50 mm dia

18.11.4:Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 rating with bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers ,gaskets conforming to IS 13095 of following sizes as required:80 mm dia

18.11.5:Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 rating with bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers ,gaskets conforming to IS 13095 of following sizes as required:100 mm dia

18.11.6:Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 rating with bronze or gun metal seat duly ISI marked complete with nuts, bolts ,washers ,gaskets conforming to IS 13095 of following sizes as required:150 mm dia

18.14.4:Providing,installation,testing and commissioning of non-return valve of following sizes conforming to IS :5312 complete with rubber gasket, GI bolts , nuts, washers etc as required.80mm dia

18.14.5:Providing,installation,testing and commissioning of non-return valve of following sizes conforming to IS :5312 complete with rubber gasket, GI bolts , nuts, washers etc as required.100 mm dia

18.15.3:Providing, installation ,testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel , Grade 304,sheet with3 mm dia holes with stainless steel flange.150 mm dia

18.17.1:Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. a) 20 mm nominal Internal dia water hose thermoplastic(Textile reinforced) type-2 as per IS:12585 b) 20 mm nominal internal dia gun metal globe valve &nozzle c) Drum and brackets for fixing the equipments on wall. d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

18.22:Providing and fixing of pressure switch in MS pipeline including connection etc as required:

16.8:Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

OD241178/2025-2026:Supply, installation, testing and commissioning of 25mm Air release valve as per IS:14845 ISI Marked as required

OD241179/2025-2026:Supply installation testing and commissioning of audio alarm hooter as required

OD241177/2025-2026:Supply, Installation , testing and commissioning of weather proof hose cabinet having the size of 750x500x250 mm made of 16 gauge MS sheet with PCC supports and full front glass door and locking arrangements suitable to accommodate 2nos 15m long hose pipes and 1 no branch pipe along with male and female coupling . The cabinet shall be painted to scarlet red colour outside and off white inside.

18.21.1:Providing,fixing, testing and commissioning of 15 mm dia quatzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Pendent Sprinkler

18.16.1:Supplying and fixing 63 m dia,15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required: Gun Metal

18.8.1:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 25mm

18.8.2:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 32mm

18.8.3:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 40mm

18.8.5:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 65mm

18.8.6:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 80 mm

18.8.7:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 100 mm

18.8.8:Providing, laying, testing and commissioning of C class heavy duty GI pipe conforming to IS 1239, i/c welding ,fittings, like elbows, tees, flanges, tapers, nuts ,bolts ,gaskets etc., and fixing the pipe on the wall , ceiling with suitable clamp or support frame and painting with two or more coats of synthetic enamel paints of required shades complete as required. 150 mm

18.9.2:Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal or stainless steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS 5290(Type A) with blank Gun metal or Stainless steel cap and chain as required:Single headed stainless steel

17.1.3:FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of manual call boxes of MS Construction in surface/recess with stainless steel chain & hammer assembly Complete with glass and push button etc. as required.

17.1.6:FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

17.1.9.2:Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.6 Zone

17.5.2:CABLING & WIRINGSupplying & laying of 2x1.5 sq mm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

OD232498/2025-2026:Fabrication, supply, Installation testing & commissioning of Electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm thick CRCA sheet, with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for terrace pump suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required. 63 A TPN SDF, Digital multifunction meter with CTs etc. LED type indicating lamps with control wiring and DOL starter for 5/7.5HP terrace pump etc as required

18.18.1:Supplying and fixing 63 mm dia gun etal short metal branch pipe ith 20 mm nominal interanal diameter size nozzle conforming to IS 903 suitable for Instantaneous connection to Interconnect hose pipe coupling as required:Supplying and fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

17.1.2:FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of smoke detector with built-in LED and mounting base complete with all connections etc. as required.

17.1.1:FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of heat detector operating at 54ºC / 57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

18.20:supplying and fixing air vessel made of 250 mm dia 8 mm thick MS sheet , 1200 mm in height with Air release valve on top and flanged connection to riser , drain arrangement with 25 mm dia Gun metal wheel valve with required accessories , pressure guage and painting with synthetic enamel paint of approved shade as required.

18.19.3:Supplying and fixing fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia M.S. Pipe connection conforming to IS 904 as required:3 way-150 mm dia M.S.Pipe

17.3.6:PUBLIC ADDRESS SYSTEMSupplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.

OD232495/2025-2026:Supply and Installation of ABC type fire extinguisher 5 kg capacity consisting of M.S Cylindrical body, squeeze lever discharge valve fitted with pressure indicating gauge internal discharge tube , 30cm long high pressure discharge hose, nozzle etc.

OD232499/2025-2026:Supply and Installation of CO2 type fire extinguisher with 4.5 kg. Capacity consisting of M.S Cylindrical body, squeeze lever discharge valve fitted with pressure indicating gauge internal discharge tube , 30cm long high pressure discharge hose, nozzle etc.

OD299601/2025-2026:SITC of self glowing FIRE EXIT sign board of size 12" x 6" as per requirement and standard , made of 3mm thick aluminium sheet layered with photoluminescent material -background colour ,letters and symbols as per IS specifications -IS 12349,IS 9457,IS 12407 either fixed on wall or provided with hanging chains & necessary supports to hang it on ceiling.

OD299602/2025-2026:Supply,installation,testing and commissioning of self glowing "FIRE ASSEMLY POINT" sign board of size 16"x16" mm made of luminescent safely, rigid sheet in green colour photo luminescent rigid sheet with two hanging chain & necessary support to hang it on ceiling

OD299756/2025-2026:Supply and fixing (in appropriate location) of Fire emergency plan (colour) printed in photo paper of size A2 sand witched in clear acrylic sheet fixed using SS studs and other accessories complete as required as per the technical specification and conforming to IS 9457,IS 12349,IS 12407

OD232497/2025-2026:Charges for preparation of Electrical/fire Drawing per A3 sheet first copy

OD232494/2025-2026:Copying charges of Electrical/fire Drawing per A3 sheet additional copies

Please Enable Macros to View BoQ information