SPL REPAIR TO BLDG NO T-195 (OTM ACCN) AND TO THE EXISTING DRAINAGE LINE FROM CSD CANTEEN TO KOTE, KOTE TO MT AREA AND PROVN OF TOILET BLOCK NEAR MT GARAGE AT MIL STN HALDWANI UNDER GE RANIKHET

Surface excavation not exceeding 0.30m deep and averaging 15 cm deep getting out hard/dense soil all as spd & directed by Engr-in charge .

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out hard/dense soil complete.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.

Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering as required

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed.

M/L for Rcc Design Mix M-25 type B-1 using 20mmFoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles complete (reinforcement to be measured separately).

M/L RCC Design Mix M-25 type B-1 using 20mm graded stone aggregate in columns, pillars, posts & struts complete (reinforcement to be measured separately).

M&L RCC design Mix M-25 type B1 using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L for 40mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate

Applying evenly a coat of blown type bitumen @1.50 kg / Sqm and blinding with clean dry sand @ 0.05 Cum/ Sqm

Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg /Sqm

M&L RCC Design Mix M-25 type B1 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like

Use and waste of form work to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work vertical or to batter, flat, rough finish surface of concrete complete all as specified and directed.

M/L Form work to sides of square or rectangular columns, pillars, posts and struts for rough finished surfaces of concrete complete.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Fair finished surfaces of concrete flat.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat.

S&F mild steel TMT bar 10 mm dia and over, as in reinforcement, cut to length, bent to shape etc, including binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

-do- but 6mm to 8mm dia.

-do- but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders complete all as spd.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4)

M&L 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate as in floor complete all as specified & directed

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4) complete all as specified.

S&F Coloured Glazed ceramic tiles in vertical surfaces 350x250mmx7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4) on fair face of brick or concrete surface complte all as specified and directed.

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM (1:4) complte all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on brick masonry surfaces, finishing the surfaces fair and even complete all as specified and directed.

M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complte all as specified and directed.

Supply only water proofing compound

S&F Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges shall be paid separately complete all as specified and directed.

S & F Sheet glass 3.0mm thick figured glass, pin hea d type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete.

M&L providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate for filling PS frame complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in fixing of hold fast, bed blocks etc including necessary form work as required complete all as specified and directed.

S&F Butt hinges 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21 complete all specified and directed.

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy.

S&F extruded aluminium alloy handles 150mm size, fabricated type, anodised

M& L Hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

M&L for 2mm thick wall care putty apply in two coats on new plastered surfaces of wall, and apply two coat of exteriar emulsion paint (Apex) over a coat of primer complete all as specified and directed

M&L for applying two coats of oil bound Distemper over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete.

Applying three coats of white wash on new Ceiling surface including preparation of surface.

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore

M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth.

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity

S&F CP Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule

S&F ibrass Chromium plated Basin Mixer valve hot and cold screwed down for iron pipe complete .

S&F Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe

S&F 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram of Make - Prayag complete all as specified and directed.

S&F Cast iron 75mm bore sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors

S&F Cast iron 100mm bore Sand cast soil, waste & vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors

S&F Cast iron 100mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured)

M&L Cast iron floor trap 75mm dia, with CP grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

S&F for Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.

S&F vitreous China squatting pan, Orissa pattern incl CI spun trap,P/S trap, size 580 x 440 mm white, with integral foot rests squat pattern closet also includes setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed.

S& F Vitreous china Urinal of white colour of size 385X 325 X 635 mm of approx weight 19 Kg model URC- WHT-13253N of Jaquar Make incl concealed spreader with back inlet, flat back, anti germ glaze complete all as specified and directed.

Supply only PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float & handle including brackets

Supply only Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed of 15 mm thick 1:6 complete all as specified and directed by Engineer in charge.

S&F Vitreous China table top basin of size 520x360x125mm of jaqaur make model No-FLS-WHT-5931 including single basin mixer,waste pipe of jaqaur make complete all as specified and directed.

S & F aluminium Hat pegs, solid body, 125 mm to 175 mm

S&F Aluminum anodized Tubular towel Ring of circular/ square shape between flanges

S&F 15mm bore angle cock CP, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed.

S&F ForToilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws Complete all as specified and directed.

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

M&L 15mm thick cement rendering in 1:3 with water proofing compound @ 3% by weight of cement over RCC roof and applying bitumen primer @ 0.30 kg/sqm and then apply hot blown bitumen grade 85/25 @ 1.2 kg/sqm and water proofing treatment by APP modified polymeric water proofing membrance (weight not less thant 3 kg /sqm) with overlap of 10 cm sealed by frame shall be laid & the overlaps sealed/fused by flame as per manufacture instructins. A coat of hot blown bitumen grade 85/25 @ 1.2 kg/sqm shall be applied on top of APP modified polymeric memberaned & finally it will be finished with a coat of aluminium paint @ 0.200Lit/sqm as per manufacture instructions complete all as specified and directed.

PCC 1:3:6 type C-2 using 40mm graded stone aggregate) as in foundation & mass concrete bed of manhole etc. complete all as specified and directed.

PCC 1:3:6 type C-1 using 20mm graded stone aggregate) as in coping etc. including necessary form work complete all as specified and directed.

PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in benching of manhole, etc including necessary form work complete all as specified and directed.

SGSW pipe 150mm nominal bore grade 'A' laid in tranches and jointed in cement mortar 1:1 and tested complete all as specified and directed.

PCC 1:3:6 type C-2 using 40mm graded stone aggregate) as in bed of drain pipes, laid to falls including packing under, haunching against the sides of pipes after they are laid, jointed and tested for 150mm bore pipe complete all as specified and directed.

RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast cement concrete, manhole covers including all use of forms, moulds or machine moulds and setting the blocks, slabs etc in cement mortar 1:4,complete all as specified and directed. (Reinforcement shall be measured and paid separately under respective item of schedule "A")

Construction of brick masonry septic tank 25 users Capacity with excavation and earth work in hard/dense soil or in soft/disintegrated rocks, PCC 1:2:4 type B-2 as in foundation, brick work in CM 1:4, RCC M-25, CI main hole cover (HD), vent, shaft and sludge chamber etc. complete all as specified, and directed .

Construction of brick masonry soak well of 3.60 m internal dia and 3.0 m effective depth and excavation & earth work in hard/dense soil or soft/disintegrated rock, PCC 1:3:6 in foundation, honey comb and solid brick work in CM 1:4, RCC M-25 cover slab, PCC 1:2:4 in bands, filling with bricks bats complete all as specified, and directed .

Demolition of cement concrete in but of any description and in any position not other wise specifically provided for complete all as specified and directed.

M&L for 100mm thick Plain Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in path/floor/paving/hardstanding etc, complete all as specified

M&L for Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in foundations, filling and mass concrete etc, complete all as specified

M&L for brick work with sub class `B’ bricks, straight on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete.

M&L precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 including necessary form work complete all as specified and directed. (reinforcement to be measured separately)

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level).

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete

M&L 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate)complete as in level course with finishing in cement concrete surface even and rough to receive screed bed complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection incl finishing even and smooth w/o using extra cement complete all as specified and directed.

M&L for providing PCC 1:2:4 type B-0 as in roof kerbs or mud stops rouded or chamfered on edges (using 12.5mm graded stone aggregate) complete all as specifed and directed.

Demolition of brick work built in cement mortar all as specified and directed.

M&L for brick work with sub class `B’ bricks, straight on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc complete.

M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturerer's instructions and finishing the surface even and smooth (without using extra cement) etc. complete all as specified NOTE -WPC shall be measured and paid separetely.

Supply only WPC complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying a layer of wall care putty 2mm thick (averaging) on wall surfaces including cornics etc for proper levelling of plaster and applying a two coats of exterior emulsion paint over a priming coat (as per manufacturers instruction) including all preparation complete all as specified and directed.

M & L for preparing new plastered or unplastered surfaces of walls and applying a layer of wall care putty 2mm thick (averaging) on wall surfaces including cornics etc and apply two coats of distemper oil emulsion, white or tinted over & including a coat of primer complete.

Dismantling plain or corrugated steel sheeting, any gauge, thickness as in roof etc., coverings complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering /cladding to wall, fixed with self tapping screws as specified complete all as specified

S &F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F framed work such as grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165.

Dismantling framed work timber scantlings 40 sq. cm and over in section, in any position

S&F rolled mild steel sections channel angle Tee section and in tubular section as in main and cross beams, hip and jack rafters; purlins,post where connected to common rafters and running rails fixed with angle cleat or other connecting plates conforming to Fe 410-W Gde-E-250, quality A complete all as specified and directed.

M&L for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on steel surfaces over 10cm width or girth including preparation of surface complete.

Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete.

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm incl iron mongry each.

S&F aluminium three track powder coated of any color (thickness of powder coating not less than 50 micron) sliding window with three sliding shutter the size of outer frame three track 92x31.5x1.2mm (using two track for glazed window shutter and one track for wire gauged), the section shutter size 37x18x1.2mm) and glazing with 4.8mm thick glas (Plain/floated) incl allround suitable rubber gasket and MS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminium flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle incl rocking arrangement & 2 numbers sliding rollers of nylon with incl all necessary fittings complete all as specified and directed.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified

S&F powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

S&F Aluminium Powder coated designer grill of 5.5 mm dia and aperture of 75 mm fixed with and including aluminium powder coated flat section of size 50 x 1.5 mm and suitable aluminium anodised frame F/H section complete all as specified and directed.

Supply & fixing aluminium sheet powder coated of thickness not less than 4mm thick to be in sealed as panel in aluminium door including fixing complete all as specified and directed.

S & F Sheet glass 4.0 mm thick tinted glass and glazing in squares complete all as specified and directed.

S&F for door closer aluminium extruded section hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises

M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete.

M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in skirting/dado or verticle surfaces with back coat of screed bed or bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified.

S&F Decorative Stainless steel tubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on each end and one no of globe on each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed.

M&L 75 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and rough complete all as specified and as directed.

M&L chequered concrete concrete tile 20cm x 20cm x 20 mm thick with white cement & pigment, set, jointed and pointed in neat cement slurry in floors, laid over 15 mm thick bedding layer in Cement Mortar 1:6 complete all as specified and as directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets but without frame work.

S&F powder coated aluminium snap grid frame work for false ceiling size of grid 605 mm x 605 mm complete all as specified and directed.

Supply & fixing 4mm thick non asbestos E-board cememt building board for insulation and accoustic purpose, 600 x 600 mm size fixed with staples on snap grid as in ceiling complete all as specified and directed.

M&L for 12mm thick Gypsum Board seamless Ceiling as in curved, sunken or raised surface of any design as approved and finishing the surface fair by filling the joint with POP and applying two coat of Oil Bound Distemper over a coat of primer inlcuding GI frame work for curved, sunken or raised for any design as approved as in ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre fixed with hanger of GI channel made out of GI channel used in ceiling as above upto 1200 mm length in roof slabs by means of ceiling cleats complete all as specified and directed.

Taking down carefully aluminium/copper wiring of any size (for light, fan, socket or power etc complete) including fixture and fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc and making good disturbed surfaces of wall, roof etc to match with existing surface.

Supply & Fixing point wiring for one light point/ fan point controlled by one, one way switch with 1.5Sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FRLSH) PVC cable drawn into & including PVC pipe conceilled wiring and accessories including PVC/Polycarbonate rectangular block for mounting, switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet cover of size fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth, etc and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed (Note:- wiring shall be done in colour coding as directed by Engineer in charge)

All as per item No 130 herein before but wiring with 2.5sqmm copper wire (FRLSH) PVC and 2.5 sqmm earth wire for socket outlet 5 pin 15 amps on independent board.

Supply & Fixing point wiring for one light point/ fan point controlled by one, one way switch with 1.5Sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FRLSH) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia ) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3 mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed (Note:- wiring shall be done in colour coding as directed by Engineer in charge.

All as per item No. 2 herein before but one socket outlet 5 Amps on the same board.

All as per item No.2 herein before but one 3 pin socket outlet 5 Amps independent.

All as per item No. 2 above but with 2.5 Sq mm two single core and 2.5 Sq mm one single core as earth wire for 5/15 Amps socket.

supply & Fixing lamp holder PVC insulated body with back plate for angle/battern fitting complete all as specified and directed

Suppy & Fixing switch piano flush type single pole, one way 5 Amp complete all as specified and directed.

Supply & Fixing switch piano, flush type single pole 15 Amp complete all as specified and directed.

Supply & Fixing socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified and directed.

Supply & Fixing socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed.

Supply & Fixing steped type electronic fan regulator flush type on the existing phenolic laminated sheet etc.

Supply & Fixing ceiling rose, PVC/ Poly carbonate, isolated body three terminal complete all as specified and directed.

Supply & Fixing sheet metal enclosure for DBs(double door type) TPN 4 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

Supply & Fixing sheet metal enclosure for DBs(double door type) single pole and neutral 8 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

Supply & Fixing 415V, 10KA 'C' curve miniature circuit breaker (MCB) of TPN 63 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Supply & Fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 to 63 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Supply & Fixing 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single pole 5 to 32 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Material and labour for Sub main wiring with 2 run of 6 Sqmm (nominal area) FRLSH, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to and including Rigid non metallic PVC conduit ( ISI marked) Heavy grade, 20 mm dia (external) inclusive of junction/terminal boxes, all fittings and accessories fixed concealed with and including 6.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB including cutting and chasing and making good surface as original by plastering and whitewash/ colour/ distemper etc including taking down existing old sub main wiring complete all as specified. Note :1 The cost of earth wire is included in the quoated rates. 2. Two run of 6 sqmm, one run of 6 sqmm and one run of PVC conduit will be measured as one unit ie one running metre”

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type (warm/milky white as required on site) with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling, life of tube light not less than 50,000 hours including connecting up with driver three core flexible copper conductor cases of suitable size complete. Make Havells/Phillips/Bajaj/C&S Note:- Contractor shall submit 2 year warrenty of material from manufracturer alongwith purchase voucher.

Supply and fixing LED lights fitting 1x 20W (warm/milky white as required on site), 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and life of tube light not less than 50,000 hours.complete all as specified and directed.. Make Havells cat pat LUMILINEBS20WLED865SPCWH or equivalent of phillips/wippro/Bajaj/Surya complete Note:- LED tube light shall be purches to get minimum 2 year warrenty of material from manufracturer.

M&L for taking down ceiling fans / wall mounted fans of any size / sweep after disconnecting the wire from existing ceiling rose and depositing to MES store yard complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories (incl ceiling clamp/hook fixing in ceiling/roof with fashner/nut & bolts), 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)complete all as specified and directed by Engineer-in-Charge.

S & F LED light fitting 1X10W, Bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make : Havells cat pat HEXAFT10WLED857SSYMBOPC or equivalent cat part in make phillips/wippro/Bajaj & C&S . Note:- Contractor shall submit 2 year warrenty of material from manufracturer alongwith purchase voucher.

M&L for Earthing complete with galvanized sheet earth plate electrodes 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2. 25mtr deep below ground level) with top edge of plat not less than 1.5 mtr below normal ground level connected to galvanized iron strip 25 x 4 mm as earthing lead by means of bolts, nuts , check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 and including excavation and earth work, GI pipe light grade 15 mm bore for protection of GI wire from earth electrode to and incl the earth test point of galvanized Iron/steel of size 75x75x 25mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6 mm dia TMT bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh,20 mm dia GI pipe light grade for watering and connected to earth test point including brazing at all joints except at test point and testing complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper cable of suitable size complete

Supply and fixing LED lights T-5 fitting 1x 20W (warm/milky white as required on site), 220V, AC with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose 1.5 RM and life of tube light not less than 50,000 hours complete all as specified and directed..

S & F exhaust fan made of sturdy Engineering plastic type ISI Mark, copper winding of sweep 300 mm size complete with louvers including cutting opening through brick/stone /PCC block wall, making of holes and grouting of suitable size of nuts and bolts for 300 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accessories complete all as specified and directed.

S & Fixing LED Bulb 9 watt all as specified and directed by Engr-in-Charge.

Supply and fix water heater storage type electric supplied and installed complete steel body with copper inner tank and heating element upto 2 KW of capacity 25 ltrs, BEE 5 Star rated including making connection with industrical socket, ultra thick SS inner tank of superior 304 grade, Fire retardant ISI Mark supply cord, Rust & shock proof ABS body, Compact & easy to install and proper hanging on nut bolts washers grouted on wall and PVC pipe for connection of hot and cold water complete all as specified and directed by Engr-in-charge.

M&L for Earthing complete with galvanized sheet earth plate electrodes 60x60x6.3 mm thick buried directly in ground (earth pit not less than 2. 25mtr deep below ground level) with top edge of plat not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm as earthing lead by means of bolts, nuts , check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 and including excavation and earth work, GI pipe light grade 15 mm bore for protection of GI wire from earth electrode to and incl the earth test point of galvanized Iron/steel of size 75x75x 25mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6 mm dia TMT bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh,20 mm dia GI pipe light grade for watering and connected to earth test point including brazing at all joints except at test point and testing complete all as specified and directed by Engr-in-Charge.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross section area 25 Sqmm 2 core laid in trenches or passing through pipes/ducts and incl the disturbence surface of road making good with using PCC complete all as specified and directed. Including taking down old LT U/G Cable from trenches/protection pipe etc complete.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross section area 16 Sqmm 4core laid in trenches or passing through pipes/ducts and incl the disturbence surface of road making good with using PCC complete all as specified and directed. Including taking down old LT U/G Cable from trenches/protection pipe etc complete.

M&L for dry clean sand filling in trenches below and around under ground cable cushioning complete all as specified and directed.. Note :- Thickness of sand cushioning shall be measured after punning.

M&L for brick sub class 'B' for protection of cable comlete all as specified and directed.

Supply and Fixing steel tube Light grade galvanised 50 mm bore with all fittings for protection of UG cable under road/culvert and fixing on wall with saddle, screw complete all as specified and directed.

Please Enable Macros to View BoQ information