COMPREHENSIVE REPAIRS TO JOINERIES, ROOF, FALSE CEILING , FLOOR, BRICK WORK , PLUMBING AND SANITARY FIXTURE, PAVING , FOOTPATH AND OTHER MISC REPAIRS IN 25 CAMP, 600 MEN WING AREA AND GE OFFICE UNDER AGE B/R-I AT YOL CANTT

Amount

PART-I:-Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Taking down roof trusses, coupled rafters or trussed beams Clear span above 4 meters & upto 8 meters, complete, all as specified.

Dismantling timber scantlingsin fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Demolition of stones or brick masonry or block walling, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete, all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness above ground level complete including removal of debris to a distance exc 50m but n.exc 100m, all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 50m but n.exc 100m, all as specified and as directed.

Demolition of cement concrete (reinforced) in Concrete of any description and in any position not otherwise specifically provided complete including removal of debris to a distance exc 50m but n.exc 100m, all as specified and as directed.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Taking down shutters of any description not exc. 1 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, unframed work, complete all as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames, steel or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete, all as specified

Dismantling stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons etc. all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing), removing and rubbish of the premises, complete all as specified.

Marble 16 to 18mm thick , green marble , (table rubbed and polished) as in floor ,kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade green marble type, all as specifiedand directed.

Plain cement concrete M-15 nominal mix, type B-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains (including necessary form work) including forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc. all as specified.

4mm thick non asbestos fibre cement building boards as in ceiling fixed or laid/ inserted to GI frame work fixed with screw, all as specified. as per manufacturer instructions and design incl GI frame work for seamless ceilling comprising of GI permeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section of 0.55mm thickness having kurled web of 50mm and flange of 26mm each lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete size of grid 605x605mm all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

75mm thick Plain cement concrete M-10 nominal mix, C-2, using 40mm graded mechanically crushed stone aggregate as in sub base path /paving complete all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.

Chequered coloured cement concrete tiles machine pressed of size 20cmx20cmx 25mm thick with grey cement, set jointed & pointed in neat cement slurry mixed with pigment to match the shade of the slab in floors laid over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified.

PCC M-10, nominal mix, C-0 using 12.5mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on fair faces of brick wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 5mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, all as specified.

Two coats of cement base paint on newly plastered surface of wall including preparation of surface complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty complete, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of ceiling including preparation of surfaces complete, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of wall including preparation of surfaces complete, all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified. Note : Reinforcement and form work shall be measured and paid separately

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)in rough finished surface of concrete complete all as specified.

MS work as in chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles con- forming to Fe.290.Gde-E-165, complete all as specified.

Factory made 2nd class hard wood (Sal/ Hollock) plain framed , panelled shutters (any numbers of panels), 35mm thick, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied & fitted to chowkats, complete all as specified.

35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides , all as specified.

6mm thick teak wood lipping on flush shutter of block board or veneered particle board for 35mm flush shutters, fixed with nail complete , all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 30mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (b) of part-I, fitted to chowkats, complete all as specified.

18/19mm thick block boards, grade 2 quality, interior grade,with decorative face veneer on both faces, fixed with screws to timber frame-work, all as specified.specified.

6mm thick teak wood lipping to block board or veneered particle board 18/19mm thick for , fixed with nail complete , all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each, and treated with tar or coal tar black paint , complete all as specified.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of small articles such as treating ends of posts, backs of chowkats, etc., area exc. 0.1Sqm but n exc 0.5 sq. m each, and treated with tar or coal tar black paint , complete all as specified.

Supply only integral water proofing compound (ISI marked) or approved brand.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/07.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

PCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Mild steel work as in bolt hooks (stay) hook and pintle hinges, bands, straps, hold fasts, clamps, wall ties, cleats, fanhooks etc. or similar small articles conforming to grade Fe-290 grade E-165, all as specified.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or wire staples or wooden beads, all as specified.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or wire staples or wooden beads, fixed in repair, all as specified.

Sheet glass 3mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Figured glass, pin head type 3mm thick and glazing with oil putty/ wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 200mm , fixed ,all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm , fixed ,all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 125mm, all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 100mm, all as specified.

Butt hinges, medium weight, cold rolled, mild steel 100mm long, all as specified.

Butt hinges, medium weight, cold rolled, mild steel 75mm long, all as specified.

Butt hinges, medium weight, cold rolled, mild steel 50mm long, all as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match , all as specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over pre- primed steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment etc. conforming to grade Fe 410 -W(Gde-E- 250 quality-A ) steel ,all as specified.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe 410 -W(Gde-E- 250 quality-A ), complete, all as specified.

Corrugated galvanized iron mild steel sheets 0.63mm thick, grade ‘O’, with 120 grams per square metre zinc coating fixed with 'J' or 'L' hook as in roof covering with two corrugation side lap. (Horizontal distance of side lap shall not be less than 145mm and depth of corrugation shall be 12.5mm), all as specified.

All as per Serial Item No Serial Item No. 61 above but Except Sheeting, all as specified. Note:- Serviceable sheets retrieved from Serial Item No 01 above shall be used.

0.80 mm thick plain galvainsed mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

2nd class hard wood (sail) as in scantling wrought timber fixed in unframed including preparation and applying one coat of black bituminous paint complete, all as specified.

2nd class hard wood (sail) as in scantling clean sawn timber fixed in unframed including preparation and applying one coat of black bituminous paint complete, all as specified.

2nd class hard wood (sail) as in scantling wrought timber fixed in framed including preparation and applying one coat of black bituminous paint complete, all as specified.

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

All as per Serial Item No 84 above but except bricks, all as specified. Note :- Servicable bricks shall be used retrieved under serial item No. 05

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified. Note: Locally available slate stone shall not be used.

All as per Serial Item No 86 above but except stone, all as specified. Note:- Servicable stone retrieved from Serial Item No 05 shall be reused.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius in half brick thick wall built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

Vitreous China wash down water closet (pedestal pattern), white fixed including traps, connection to drain or outgoing pipe, PVC 32mm dia flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets , fixed complete ,fixed in repairs all as specified, Make as per Appx 'C'

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate and PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets,32mm dia flushing pipe, anti-syphonage pipe complete including fittings,complete all as specified,including connections to trap and to flush pipe, etc and making good to floors to match existing, in repair, all as specified. Make: as per Appx 'C'

Wash hand basins, Vitreous China of size 550mmx400mm, white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and 32mm dia CP brass waste coupling, chain and plug and porcelain stopper, waste fittings such as 32mm dia flexible PVC waste pipe fixed, 15mm bore brass chromium plated pillar tap,screwed for iron pipe and fixed in repairs, complete all as specified,Make as per Appx 'C'

Vitreous China bowl Urinal, flat back 465x355x265mm ,white ( white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm bore PVC waste pipe, complete all as specified.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15 mm bore and fixed complete, all as specified.

Supply and fixed in repair PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long and 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends , fixed complete , all as specified.

PVC coloured seat cover for WC closed pattern , with mild steel chromium plated or aluminium hinges device complete ,fixed in repairs all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 98 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 06 shall be used).

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor/ sunken floor spout complete, all as specified and directed.

All as per Serial Item No 100 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 07 shall be used).

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor/ sunken floor spout complete, including taking down, all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified.

40mm bore , High density polyethylene pipes (HDPE) of pressure rating 6 kgf/Sqcm fixed complete to walls, ceilings or in floors etc including short lengths, with all pipe fittings uch as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls, floors and their making good, complete all as specified.

Sink with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, including 40mm dia waste pipe & CP waste coupling ,overall size 915mm x 460mm bowl size 405mm x 335mm x 178 mm, all as specified.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, chromium plated screwed for iron pipe or for brass ferrule and fixed in repair , all as specified.

Chromium plated brass shower rose, 125mm size suitable for 15mm bore pipe with swivel joint fixed in repair to pipe, complete all as specified.

Stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair complete, all as specified.

Stop valve, chromium plated, concealed type cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair complete, all as specified.

Angle valve, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair complete, all as specified.

Jet spray set chromium plated, hygenic ( health faucet) with 15mm dia 1 metre long with acrylic tube complete fixed in repair all as specified.

Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.

Disconnecting existing PVC/ferro cement/MS tanks capacity exc.250 litres but n. exc 500 litres , setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position, all as specified.

Disconnecting existing PVC/ferro cement/MS tanks capacity exc.500 litres but n. exc 1000 litres , setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position, all as specified.

S&F in repairs 20mm PTMT nipple suitable for HDPE water tank ( Minimum weight 20mm-38 gms) all as specified.

S&F in repairs 25mm PTMT nipple suitable for HDPE water tank ( Minimum weight 25mm-65 gms) all as specified.

Gun metal, globe or gate valves , screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed complete, all as specified.

Gun metal, globe or gate valves , screwed down, high pressure with crutch or butterfly handle, screwed both ends for 25mm bore iron pipe or for unions and fixed complete, all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair ,complete all as specified.

25mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair ,complete all as specified.

M/s Khanna Construction company

m/s Sohan singh barwal and Brothers

M/S HIM BUILDERS

Eshaan Construction Co.

M/S DAYA SONS