Renovation of the chamber of Joint Director (DME) of Agartala Govt. Dental College, Agartala during the year 2025-26 / SH Wood Wall Panelling, Brickwork, Plastering, Tiles, Sanitary fittings etc

Supplying and filling in plinth, under floor,foundations etc. with sand 9finefrom local quarry with all lifts including spreading in horizontal layers, watering, grading to require slope, ramming, comsolidating and compactibng each layer by using plate compactor or by any suitable method complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring an shuttering-All work up to plinth level 1:3;6 (1cement:3fine sand:6graded stone aggregate 40mm nominal size)

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).

12 mm cement plaster of mix Cement mortar 1:5 (1 cement : 5 fine sand)

Providing & fixing in position treated (as per IS 401) rubber wood wall cladding at all height with finger jointed edge glued solid rubber wood board planks of sizes 12 mm thick, 1000mm length (minimum) and 100 mm wide (minimum), in approved colour, texture and finish, with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of treated rubber wood of size 50mmx25mm placed at 500mm (maximum) apart and Performance Appraisal Certificate (PAC) issued by TFDPC Ltd) All complete as per direction of the Engineer in-charge.

Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised/plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of "H" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS "U" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter).

30mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a UPVC profile section of size 30mm x 60mm and wall thickness 2mm ± 0.2mm with inbuilt decorative moulding edging on one side. The styles and rails with plastic brackets of size 75×220 mm mitred and welded at the corners. The styles of the shutter reinforced by inserting galvanised MS tube of size 25×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of "H" Section, a UPVC profile section of size 30×100 mm and 2 mm ± 0.2 mm wall thickness welded to the shutter style with a UPVCprofile section single panel of size not less than 620mm, having overall thickness of 20 mm and 1 mm ± 0.1mm wall thickness with 20 mm panel beading of suitable size/Glass (4 mm thick plain glass)/ louver section, louver frame of suitable size, complete as permanufacturer's specification and direction of Engineer- In-Charge. (for W.C. and Bathroom door shutter).

Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by themanufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.Size of tile 600 mm x 600 mm

Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.450 mm X 300 mm in all shades and design

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings:Flat back wash basin of size 630x450mm

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

15 mm outer dia. nominal bore

20 mm outer dia. nominal bore

25 mm outer dia. nominal bore

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms.

Providing and fixing PTMT pillar cock of approved quality and colour .15mm nominal bore, 125mm long foam flow, Weighing not less than 120 gms

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85gms

Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 122 mm long, weighing not less than 99 gms.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of specialsections, power pressed from M.S. sheets and galvanizedwith zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips madeout of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primersuitable for board, all as per manufacturer's specificationand also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as perdrawings, specification and direction of the Engin

12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral staircases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-1:1.5:3 (1cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size)

Centering shuttering including struttings, propping etc and removal of formwork forlintels, beams, plinth beamns, girders, bressumers and cantilevers with wooden plank

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete aboveplinth level.Thermo-Mechanically Treated bars of Grade Fe-500D or more

Providing and fitting, fixing of wooden window blinds with 50 mm wide slats, made by hard PVC materials as per direction of the Engineer-in-Charge

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in positionLocal Teak Wood

Prelaminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked

Decorative plywood both side decorative veneer (Type -1) conforming to IS 1328 BWR type.

Please Enable Macros to View BoQ information