Construction of Sarai/Community Bhawan and Toilet, Kul Devi Mandir, W.No. 02 in the land of Sumer, Dinesh Rana, G.P. Chachian, Dev. Block Bhawarna, Distt. Kangra H.P.

Amount

Excavation by mechanical means (Hydraulic excavator) / manual means in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three meters) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimeter)layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Filling excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in foundation footings, basis of columns etcetera and mass concrete, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Columns, pillars, posts and struts, (square, rectangular/ polygonal in plan), up to all floor level, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders and lintels, sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto any depth/heights, up to all floor level and as directed by the Engineer-in-Charge including carriage materials of within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings, shelves, and the like floor, etcetra up to any thickness, up to all floor level and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls upto any width, up to all floor level and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (Forty millimeter) nominal size) and curing complete, in or under water, including pumping or bailing out water/dewatering, removal of slush which may arise at the time of laying under water complete excluding the cost of form work in foundation and plinth in all depths/heights as per HPPWD specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work Grade M-20 (Twenty) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimeter with cement contents not less than 330 kg (three hundred thirty) Killogram per cubic meter and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in foundation footings, bases of columns etcetera and the like mass concrete complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 25 N/mm2 (twenty five newton) per square millimeter with minimum cement contents of 400kg (Four hundred kilogrammes) per cubic metre and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in columns, pillars, piers, abutments, posts and struts etcetra up to all floor five level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work Grade M-20 (Twenty) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimeter with cement contents not less than 320 Kg (three hundred twenty) Killogramme per cubic meter and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landings and shelves and their supports, balconies, beams, girders, bressumers cantilevers and the like shelves and work tops etcetera in all upto all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying Tor steel of SAIL/ TISCO/ JINDAL/ KAMDHENU/ SHYAM STEEL reinforcement for thermo mechanically coated bars of grade Fe500D for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Brick work using Second class common burnt clay F.P.S. (non modular) buildings bricks of class designation 7.5 in super-structure above plinth level upto all floor level in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete as per directions of Engineer -in -charge including carriage of materials within all leads and lifts. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Dry Stone pitching 22.05 cm thick including supply of stones and preparing surface complete as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Random rubble masonry/ polygonal rubble masonry (un-coursed/ brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve graded crushed/ broken stone aggregate 20mm (Twenty milimetres) nominal size) at plinth level in cement mortar 1:6 (One cement : six sand) and curing complete, including carriage of materials within all leads and lifts and other incidental charges. The rate includes, royality charges, octroi, GST sale tax, malkana and all other taxes as imposed by the Government.

Providing first class sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm thick (thirty-five mili metres) well seasoned hollock wood glazed shutters for doors, windows and clerestory windows using 4 mm (four mili metre) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm thick ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm thick (thirty-five mili metres) well seasoned hollock wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directionnns with wire of dia 0.63 mm, for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing 40x5 mm (Forty X five mili metres) flat iron hold fast 40 cm (forty centimetre)long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm nominal size).complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc.Fixed to openings /wooden frames with rawl plugs screws including priming coat with approved steel primer and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 300x16mm (three hundred milimetres X Sixteen milimetres) aluminium sliding door bolts, make of PILOT/Sheel anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred into ten millimetre) aluminium Tower bolts make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100x10mm (One hundred into ten millimetre) aluminium Tower bolts make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 125mm (One hundred twenty five millimetre) aluminium Handles make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetre) aluminium Handles make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing aluminium hanging twin rubber floor door stopper make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing bright finished brass hard drawn hooks and eyes : 150mm size complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying vitrified floor tiles of Restile/ Nitco/ Rak/ Simpolo/ AGL/ Kajaria/ Johnson/ Orient bell/ Somany of 600x600x10mm (Six hundred millimetre into six hundred millimetre into ten millimetre) size manufactured of approved shade and colour with water absorption less than 0.08% (Zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (Twenty millimetre) thick cement mortar 1:4 (one cement isto four coarse sand), jointing with grey cement slurry at the rate 3.3 kg/ sqm (Three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etcetra complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. The sample of tiles shall be got approved from engineer incharge before use.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture (Asian Paints/Nerolac Paints/ Burger Paints/ Dulux Paints) on wood work (hard and soft wood) complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Painting wood work Two or more coat with Deluxe Multi Surface Paint of required shade. applied at the rate 0.90 ltr/10 sqm (Zero point nine zero litre per ten square metre) over an under coat of primer applied at the rate 0.75 ltr/10 sqm (Zero point seven five litre per ten square metre) of approved brand and manufacture as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3 (one cement isto three sand), up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on rough/ fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1mm (One millimtre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Finishing walls with Acrylic Smooth exterior paint of required shade on New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Making plinth protection 50mm (Fifty millimeters)thick of cement concrete 1:3:6 (One cement : Three coarse sand (zone - III) : Six graded stone aggregate 20 mm nominal size) over 75mm (Seventy five millimeters)thick bed of dry brick ballast 40 mm(Forty millimeters) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth and carriage of material within all leads and lifts.

Rakesh Kapoor

Individual

Ravinder Kumar

ayush