Welcome maintenance of Officers Md Accn including repair and replacement of Sanitary Fittings and cleaning of Tanks of certain Sailors/ Officers Md Accn at INS Valsura, Jamnagar

Amount

Taking down cement plaster of any description on PCC/stone surface/brick surfaces including raking out joints, hacking for key scrubbing down with water etc and removal of entire debris as ordered outside MoD land complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for in this Schedule and removal of entire debris as ordered outside MoD land complete all as specified & as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, including removal of entire debris as ordered outside MoD land complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MoD land complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in levelling course in floor, padding over roof and similar works, laid & compacted by maintaining gradient/ undulation to a minimum consolidated thickness of 25mm as directed, finished the surface fair & even, complete all as specified and as directed.

Supply only Integral Water Proofing Compound (ISI Marked).

S&F in repairs 150 mm long aluminium, anodised, barrel tower bolt (ISI marked) of extruded section and fixed.

S&F in repairs 100 mm long aluminium, anodised, barrel tower bolt (ISI marked) of extruded section and fixed.

S&F in repairs 200mm size extruded aluminium alloy handles (ISI Marked), fabricated type, anodised and fixed.

S&F in repairs 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F in repairs 80mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed. Note :- Door stopper shall be conforming to the sample kept in GE’s office.

S&F in repairs XPM design aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples along with wooden beads complete all as specified and as directed.

S&F in repairs stainless steel drapery rod of 25mm dia (in lengths as directed) with & including stainless steel decorative SS bulb type finial at both ends / SS end socket and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified & as directed.

M&L for 16 to 18 mm thick granite slab (Jet Black) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin counter and the like, set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for double charged vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (shade & pattern as approved by GE), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed. Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work.

M&L for double charged vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (shade & pattern as approved by GE), on vertical surfaces such as skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4, size of tiles as directed by GE to match the size of vitrified tiles provided in floor under respective item in this Schedule, complete all as specified and as directed. Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work.

M&L for glazed ceramic coloured tiles, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e. 600mm x 300mm or as directed by Engineer-in-Charge), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick back coat in CM 1:4 complete all as specified and as directed. Notes : (i) Quoted rate shall deemed to be inclusive of cement screed/ plaster. (ii) Colour of tiles shall be got approved from GE before incorporation in the work.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 20mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brick work of walls mixed with WPC @ minimum 2% by weight of cement or as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid for separately as 'Supply only'.

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces in ceiling in patches and scattered places, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and as directed.

M&L for preparation of old surfaces of walls including scraping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old surfaces of ceilings including scraping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick layer of white cement based wall care putty complete all as specified & as directed.

M&L for preparation of old decorated surfaces of walls including cornices etc (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and washing and applying one coat of oil emulsion distemper (OBD) of approved shade/tint by mechanical means/ auto roller including filling undulations with white cement based wall care putty mixed with multi purpose mixer complete all as specified and as directed.

M&L for preparation of old decorated surfaces of ceilings including cornices etc (plastered or unplastered) of any description, rubbing, scrapping by hand held sander/ long handle sander and washing and applying one coat of oil emulsion distemper (OBD) of approved shade/tint by mechanical means/ auto roller including filling undulations with white cement based wall care putty mixed with multi purpose mixer complete all as specified and as directed.

M&L for complete removal of existing treatment of any type on walls by rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying two coats of oil emulsion distemper (OBD) of approved shade/tint by mechanical means / auto roller over a coat of primer over & including a coat of 1mm thick layer of white cement based wall care putty mixed with multi purpose mixer complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls including cornices etc (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and washing and applying one coat of plastic emulsion paint of approved shade/tint by mechanical means / auto roller including filling undulations with white cement based wall care putty mixed with multi purpose mixer complete all as specified and as directed.

M&L for preparation of old decorated surfaces of wall including cornices etc (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and washing and applying one coat of cement based paint of approved shade/tint by mechanical means complete all as specified and as directed.

M&L for complete removal of existing treatment of any type on walls by rubbing, scrapping by mechanical means (any number of layers) by hand held sander / long handle sander and Jet pressure washing and applying two coats of cement based paint of approved shade/tint by mechanical means / auto roller over a coat of alkali resistant primer over & including 1mm thick water proof wall care putty suitable for exterior surfaces exposed to weather as per manufacturer's instructions complete all as specified and as directed.

M&L for preparing newly plastered surface of walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over & including 1mm thick water proof wall care putty suitable for exterior surfaces exposed to weather as per manufacturer's instructions complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls including cornices etc (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm applied by mechanical means i.e Airless spray complete all as specified and as directed.

M&L for complete removal of existing treatment by mechanical means (any number of layers) by hand held sander/ long handle sander, rubbing down, stopping of distempered & Jet pressure washing and painted surface of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of shade as approved by Engineer-in-Charge (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over & including 1mm thick water proof wall care putty suitable for exterior surfaces exposed to weather as per manufacturer's instructions complete all as specified and as directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of 1st quality synthetic enamel paint of approved tint complete all as specified & as directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying two coats of 1st quality synthetic enamel paint of approved tint complete all as specified & as directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of 1st quality synthetic enamel paint of approved tint complete all as specified & as directed.

M&L for French polishing one or more coats on wooden or wood based surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works until high glossy finish is obtained complete all as specified and as directed. Notes applicable to all items for periodical services here-in-above: (i) For measurement purposes in respect of those building for which audited Periodical Services Measurement Book (PSMB) are available, quantities shall be taken directly from PSMBs and entered in Measurement Book (IAFW-2261) and in respect of those buiidings for which audited PSMBs are not available, detailed measurements of works shall be taken and entered in Measurement Book in the usual manner. (ii) Any fittings or fixtures disturbed or damaged during the progress of work, will either be rectified or replaced by the contractor himself without any delay and at no extra cost to the Govt. (iii) Prior approval of colour shade/ tint is mandatory from GE before commencement of work. (iv) The quoted rate aganist various items of above Schedule shall deemed to be inclusive of preparation of surfaces with Hand held sander / long handle sander, cleaning the wall/ ceiling surface with jet pressure washer, mixing putty with multipurpose mixer, applying Anti fungal paint with Airless spray appliance, and applying distemper & Plastic emulsion paint with Mechanical means / Auto roller as ordered. (v) Contractor shall obtain prior approval of Engineer-in-Charge for cleaning & application items before commencement of periodical work.

Hacking out old broken glass (any thickness) and size from wooden frame glazed with putty or fixed with wooden beads complete all as directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads or fixed to aluminium sections not exceeding 0.5 Sqm in each pane complete all as specified & as directed.

Taking down or up damaged/ old GI pipe of 15 mm bore and S&F new 15 mm bore galvanized steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as specified and as directed.

Taking down or up damaged/ old GI pipe of 20 mm bore and S&F new 20 mm bore galvanized steel water tubing medium grade (ISI marked) with all new fittings (ISI marked) fixed to wall and ceiling or laid in floors complete all as specified and as directed.

S&F in repairs ball valve, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball, screwed for iron pipe or brass ferrule of 20 mm bore and fixed (minimum weight 210 gms) complete all as specified and as directed..

S&F in repairs 15mm bore bib tap with wall flange, fancy type, cast copper alloy, chromium plated screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. PIS-06 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore bib tap long nose with wall flange, fancy type, cast copper alloy, chromium plated, long shank screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. PIS-09 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore bib cock sink tap regular spout (W/M) with flange, fancy type, CP cast copper alloy, with capstan heads, with long screwed shanks and fly-nuts, screwed down high pressure, screwed for iron pipe complete all as directed. Make: Prayag Cat No. PIS-16 H or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore two way bib tap fancy type, brass, chromium plated with flange and aerator, screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: Prayag Cat No. PIS-12 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs CP ABS body Health Faucet with 1 mtr SS Chrome plated tube & hook wall mounted type complete all as specified and as directed. Make: Prayag Cat No. BEA-97 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore pillar taps, fancy type, CP cast copper alloy, with capstan heads, with long screwed shanks and fly-nuts, screwed down high pressure, with or without lettered 'Hot' or 'Cold' screwed for iron pipe complete all as directed. Make : Prayag Cat No PIS-02 H or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore pillar tap, Swan neck, fancy type, long body, CP cast copper alloy, with capstan heads, with long screwed shanks and fly-nuts, screwed down high pressure, screwed for iron pipe complete all as directed. Make: Prayag Cat No. PIS-14H or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs concealed type stop valve with wall flange 15 mm bore of pipe, brass chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make: Prayag Cat No PIS-18 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore angle cock with wall flange, chromium plated brass, screwed both for iron pipe or brass ferrule complete all as directed. Make: Prayag Cat No. PIS-10 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs chromium plated 110mm square over head ABS shower with SS Arms & Flange, swivel joints fixing to steel pipes etc complete all as directed. Make : Prayag Cat No BS-72N or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore brass, chromium plated, sink mixer wall mounted with 170mm long swivel spout, connecting legs and wall fange, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. Make: Prayag Cat No. 7555 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore, brass, chromium plated, wall mixer with L bend with wall flange and one for shower rose, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe complete all as directed. Make: Prayag Cat No. 6875 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 15 mm bore, brass, chromium plated, single lever basin mixer W/O pop up waste system for hot and cold water mixing, screwed for iron pipe complete all as directed. Make: Prayag Cat No. 7851-N or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs CP Brass toilet paper holder with flap guard complete all as specified and as directed. Make: Cat Part No BA-18S of Prayag or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make : Prayag Cat No BA-40 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs CP brass towel ring fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make : Prayag Cat No BA-41 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repair CP brass towel rack 600mm (24") long fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make: Prayag Cat No. BA-03 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs CP brass bottle trap 175mm (7') including all connecting accessories complete all as specified & as directed. Make : Prayag Cat Part No BEA-23 or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs bathroom cabinet mirror (400x500mm) including fixing screws complete all as specified and as directed. Make: Prayag Cat No. 554 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs glass Shelf 500 x 125 mm with brass brackets fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make : Cat Part No BEA-45 of Prayag or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Corner glass Shelf 300mm with Brass brackets fixed on wall with PVC rawl plug & chromium plated brass screws complete all as specified and as directed. Make : Cat Part No BEA-44 of Prayag or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repair CP brass soap dish including fixing with brass screws complete all as specified & as directed. Make : Prayag Cat No BA-05 or equivalent in makes mentioned in Appendix 'B' here-in-after

S&F in repairs grating square 140 mm size of stainless steel without hole and fixed complete all as specified & as directed.

S&F in repairs PVC connections 15mm dia, 450mm long with PTMT nuts & washers at both ends complete all as specified & as directed.

S&F in repairs PVC flexible waste pipe for 32mm dia waste coupling complete all as specified and as directed

S&F in repairs 50 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm, fixed to wall/ ceilings or in floors etc. complete all as directed.

S&F in repairs PVC (SWR) floor trap plain with grating including jointing with solvent cement, diameter of outlet 75mm, complete all as specified & as directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm/ suitable fastener bolts, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc, including lime concrete bedding and making good disturbed floor, complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., complete all as specified & as directed.

S&F in repairs vitreous China ware wash down water closet (EWC), snow white, one piece with slim soft close seat cover and twin flush fittings complete all as directed. Make: Cera Cat No. S1013246 or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F in repairs 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and flush pipe of polyetylene of low or high density or 32 mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device complete all as directed.

S&F sink without draining board, glossy finished, made out of 1.00 mm thick stainless steel sheet for kitchen or laboratory with plug, washers and waste pipe, including bedding in CM to dwarf wall or including fixing cantilever, brackets and connecting union to pipe, overall size 495x420 mm with bowl size 410x330x160 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings.

S&F sink with drainage board, glossy finished, made of stainless steel 1mm thick for Kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to brick wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings.

S&F in repairs corrosion resistant Stainless Steel Kitchen plate rack of size 31x30x10 inch, with 0.80 mm thick Stainless Steel sheet (min weight 7.00 Kg) fixed to walls with rawl plug and brass screws, complete all as specified and as directed. Make: Prayag Cat No. P-346 or equivalent in makes mentioned in Appendix 'B' here-in-after.

Cleaning and removing all scale and dirt, etc, from tanks of capacity exceeding 250 ltrs and not exceeding 500 ltrs and from mouths of circulating pipes, etc. complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc, from tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs and from mouths of circulating pipes, etc. complete all as specified and as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and S&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover hoisted and fixed in position where ordered and making necessary connections for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and S&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover hoisted and fixed in position where ordered and making necessary connections for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

Amar Constructions (BID ID -3312594)

S t modi (BID ID -3314574)

Prashiv Enterprise (BID ID -3311856)

1R K Traders (BID ID -3312627)

Sagar Builders (BID ID -3311718)

Suraj Builders (BID ID -3314070)