Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | As L1₹29.8 LAccepted-AOC 184 187 TEMPLESTEPS BLOCK ANNASALAI LITTLEMOUNT CHENNAI CHENNAI TAMIL NADU 600015 | CHENNAI | TAMIL NADU | 600015 | As L1 | Accepted-AOC L1 | |
| 2 | As L2Rejected-Finance 5TH FLOOR DP 9 P T I BLDG SALT LAKE SALT LAKE KOLKATA WEST BENGAL 700091 | KOLKATA | KOLKATA | WEST BENGAL | 700091 | As L2 | Rejected-Finance As L2 |
Tender Value
₹43.5 L
EMD Value
₹87,000
Closing Date
11 Sept 2018, 9:00 amClosed
Executive Engineer PWD BDN ELEC DIVN
Room no 1081st fl purta bhawan salt lake kolkata
Modernization of Two 2 Nos Lift of 15 16 Passenger at Purta Bhavan and also Installation Testing and Commissioning of 15 16 passenger lift at Purta Bhavan salt lake Kolkata 700091
2018_WBPWD_186081_1
WBPWD/EE/BED/22/e-IT of 2018_19/2nd call
Open Tender
ELECTRICAL WORKS M/R
Item Rate
120 days
Purta Bhavan
Please refer Tender documents.
4 documents required · 4 mandatory
₹87,000
Yes
29 Sept 2021
13 Aug 2018
13 Sept 2018
18 Aug 2018
11 Sept 2018
18 Aug 2018
Amount
Dismantling existing OTIS make Lift and SITC of Automatic Lift (as per manufacture design & as per detailed specification below conforming to IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and reparing the damage wall/ floor if any etc to complete as reqd.(i) Make:OTIS/KONE/SCHINDLER (ii) Type: 15/16 Paaenger-----Lift.(iii) Load:(1020/1088 Kg/68kg/Paaenger (iv) Control:Microprocessor based with AC variable voltage & varible frequency (VVVF). (v) Machine:-Energy eficient machine, Garless, with Machine Room. (vi) Position of Machine Room :Directly above the Lift shaft. (vii) Speed: 01(one) mtr/sec. (viii) Floors served:-----(G+3) building (ix) Landing:4 stop/4 opening---all on same side (x) Total Rise:15.6(approx)----Mtr (xi) Operation :Micropocessor based Simplex full collective with or without attendant. (xii) signls:Digital car position indicator, car travels direction indicator in car & at all landing aith call registaration indicator. (xiii) Leveling accuracy:+ 5mm (Micro levelling arrangement) (xiv) CAR (xv) Car inside:--2200 mm high, minimum are as per L.S. Code (xvi) Car Entrance:Clear Opening 900---mm (W) x 2000----mm (H) protected with car door. (xvii) Car Enclosure:Stainless Steel sheet (20SWG) with Hairline finish with hand rail. (xviii) Car Ceiling & Lighting:Stainless steel with hairline finish with LED lightiong and Fan. (xix) Car Ventilation:as per manufacture standard (xx) Car Flooring:Car flooring: Decorhtive granite flooring (As per direcion of EIC and According to this Department's Order) (xxi) Car Door:Stainless Steel center opening automatic door provided with V3F controlled door drive system. (xxii) Landing Door:Stainless Steel center opening automatic door provided with V3F controlled door drive system. (xxiii) Door Op[ening Automatic power oprated door with full length photocell assombly light curtain sensor. PROTECTIVE DEVICES&OTHER ACESSORIES : (i) ARD: Automatic reecue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in onse of both power failure and single phasing. (ii) Overlond Protection :Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and audio display indication. (iii) Emergency lighting in car Battery operated emergency lighting in the lift car. (iv) Intercom system :Battery operated intercomsystem in Lit Car. Machine Room & Control Room. (v) Emergency Alarm: Battery operated alarm bell system in lift car and control room. (vi) Fireman switch:Fireman switch at main landing terminal. (vii) Voice Synthesizer:voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. (viii) Main rope- As per manufature's standard conforming to IS. DIMENSION OP SHAFT & POWER SUPPLY : (i) Available Shaft Dimension: 2000--mm X 2700 - mm (ii) Pit Depth:- 1550-- mm (iii) Overhead:------- mm (iv) Electric power supply :AC 416 Volt 3 phase, 50 Hz terminated in machine room as per IS. (N.B. : For cost of dismantled material Rs. 75,000/- will be deducted from the bill of the agency) N.B.: (i) The Agency must procure the materials from the Manufacturer / OEM or from their authorized. Sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them. (ii) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution of work / submission of bill. (iii) If any refurbished material is supplied and installed, penal action will be taken as per existing rules.
L.W.C. must be quoted manually @1% on the total quoted value else the total quoted rate shall be treated incl. LWC as per rule. N.B. Rate should be quoted inclusive of GST.
KONE ELEVATOR INDIA PRIVATE LIMITED
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.05 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .