Furniture Supply for Schools District Kota

Amount

Class Room Table ( Dual Desk) with Attached Chair The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within classrooms. The panels are made from 16 gauge MS sheet thick all sides. Top Dimension shall be 1048 X 378mm. Top Height shall be 750mm. Seat Dimension shall be 1048 X 335mm. Seat Height shall be 437mm. Back dimensions shall be 1048 X 265mm. Size may vary +/- 5mm. The Under structure is Made of ERW tubes[IS 7138] 25.4 ±0.3mm x 25.4 ±0.3mm x1.2 ±0.096mm thick powder coated 50microns(±10) at base which are welded to the desk and seat supports that are made of MS 'C' sections 29+/-0.3mm X 24.9+/-0.3mm X 1.2+/-0.096mm thick powder coated 50microns (±10). Stiffeners that are provided between the 2 vertical frames at base and back of seat are made from ERW tubes[IS 7138] 25.4 ±0.3mm x 25.4 ±0.3mm x1.2 ±0.096mm thick powder coated 50microns (±10). The tubes are closed with plastic caps. Additional horizontal supports of ERW tubes[IS 7138] 25.4 ±0.3mm x 25.4 ±0.3mm x1.2 ±0.096mm thick powder coated 50microns (±10) are placed Between front legs and between back legs to add the rigidity of the structure. The storage shelves are made from 1mm ±0.09mm thick powder coated 50 microns(±10) MS sheet which is affixed below the desk top. Hooks are provided on either sides of the vertical frame of the desk, for hanging bags/bottles. They are made from 6.0 mm dia MS rods powder coated 50microns (±10) The under structure is assembled using M5 Trilobular Taptite screws. Nylon studs are provided on bottom side of RH/LH Frame. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted. Top understructure – 960mm (W) X 310mm(D). Back Panel Support – 960mm(W) X 325mm(H). Seat support – 960mm(W) X 280mm(D). 3D View is as under:-

Teacher Table The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within classrooms. The table shall have 1199 (w) X 590 (d) X 750 (H). The work surface of the table shall be 18 +/- 0.5 mm thick Pre Laminated MDF Board (IS14587) top with 2 mm thick PVC edge beading on all sides. The understurcture shall be C frame of 0.9+/-0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. The tubular frame shall be of dia. 25.4+/-0.3 mm X 1.2+/-0.096 mm thick MS ERW round tubes. It shall have 3 drawer unit & shall be 355.5 mm W X 559 mm D X 433.5 mm H, with shell of 0.5+/-0.07 mm thick CRCA MS & drawer tray of 0.5+/-0.07 mm thick CRCA MS & drawer front of 0.8+/-0.1 mm thick CRCA MS & the drawer friction slide shall have 1.2 mm thick CRCA MS & lock shall be of 10 lever cam lock. Handles shall be built in plastic. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted. Top Under structure frame – 1165mm (W) X 558mm(D).

Teacher Chair The seat and back are made from seasoned wood, caned and finished with synthetic paint (Colour: Black ). BACK SIZE: 38.1CM(W) X 39.0CM(H). SEAT SIZE: 38.1 cm(W) x 42.4cm(D). The cane is produced from blends of High and Low Density polyethylene. The cane high tensile strength at break=1400 kg/cm2(min.) & Elongation at break=54% maximum. The understurcture assembly is a cantilever type frame made of dia. 2.54+/-0.03cm x0.2+/-0.016cm thick M.S. E.R.W. tube and powder coated. (DFT 40-60 microns). Wood used in the manufacturing of seat and back should be free from defects, termite free and after caning should bear a load of 130KG in fitted position. Also there should be no permanent deformation or structural changes in the frame structre on apply of this load. At the bottom of frame lugs should be press fitted in punched holes in the frame structure. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted

Library Table The product should be in complete knock down condition as much as possible/ feasible enabling ease in transportation and assemblies within premises. Top Size:- 2300x1100 X 750mm (H). The Worktop will be made of 25mm thick MDF Board (IS14587) with Post forming Laminate and balancing Laminate. Post forming on two Longer side and two short Side PVC lipping 2.0 mm thk..The under structure is made from 38±0.3 mm X 38± 0.3mm X 1.5 ±0.128 mm thick MS Tube with powder coated 50 microns(±10) ( IS 7138 ) at base which are welded and are fixed to top with Chip board Screws. Under structure size 2220mm X 1020mm and 2 additional middile support of 1020mm. The Bottom ends are closed with plastic buffers. The cross members are made from 38±0.3mm X 38±0.3mm X1.5±0.128 mm thk MS Tube at base which are MIG welded and are bolted to Side frames. The Bottom stiffeners are connected with Hexagonal bolts. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted

Library Chair The seat & back shell of chair shall be injection moulded Polypropylene. Seat size – 46.0Ccm(W) X 38.0cm.(D). Back Size – 41.0cm(W) X 40.0cm(H). Tubular Under structure- The tubular under structure is fabricated from dia 1.9+/-0.02cm X 0.1+/-0.008cm thk. SS202 Grade tube welded together with SS connecting rod dia 0.8+/-0.0058cm. The under structure is provided with black PP injection moulded ferrules.

Library Book Rack Double Sided The product should be in complete knock down condition as much as possible/ feasible enabling ease in transportation and assemblies within premises Product Size: Width 900mm, Height: 1850mm, Depth: 600mm. Construction: Rigid Knockdown construction. Material: CRCA 0.9mm Thickness. Finish: Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Number of Adjustable shelf: Five adjustable shelves on one side (Total 12 Loading levels). Uniformly Distributed Load Capacity per each shelf is 80 Kg maximum. Shelf back stiffener : At the rear side of the shelves back stiffeners are provided. These act as separators between front & rear books. Label holder & range Indicator: Label Holder & Range indicator on each main unit for inserting labels. The powder coated components are on regular basis tested for Scratch resistance test of 4 kgs & for Impact resistance test for 150kgs/cm. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted.

Library Book Shelf Almirah Size shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) Excluding levellers. It shall made of 0.7 mm thk(+/-0.07mm) CRCA for Shelf, 0.8 mm thk(+/-0.08mm) High yield strength CRCA for doors and back & 0.9 mm thk(+/-0.08mm) CRCA for all other components. Construction shall be welded construction. *CRCA 'D' grade as per IS:513. CRCA 'D' grade high yield strength as per IS:513. Construction shall be welded construction. Locking and Handle – Brass handle, Two way locking mechanism with shooting bolt. Height wise 4 nos of Adjustable Shelf shall be provided with Uniformly Distributed Load Capacity per each full shelf is 40 Kg maximum. M10 Screw type leveller with hex plastic base. Outer Finish shall be Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).). All steel structural components are processed shall be made from virgin and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. The powder coated components are on regular basis tested for Scratch resistance test of 4 kgs & for Impact resistance test for 150kgs/cm. Recycled steel will not be accepted

Computer Table The product should be in complete knock down condition as much as possible/ feasible enabling ease in transportation and assemblies within premesis Dimension of the table shall be 1200 X 600 X 745mm. Table should accompanied with keyboard, pullout tray. The Desk Panel is made from 25±0.5mm THK Pre – laminated MDF Board (IS14587) with 2 mm thick PVC beadings on all sides. The Under structure is made of 50.8±0.3X25.4±0.3mmX1.6±0.096mm thick powder coated ERW tubes as per ( IS -7138 ) at base which are welded to the vertical channels made of 1.2±0.09mm thick Powder Coated Micron 50(±10)MS “ C “ Sections. The Footrest is 1.2mm thk fabricated from MS sheet in C shape and Modesty panel is 0.8mm thk – 1185mm X 200mm. Footrest and Modesty panels are provided for overall stability of product . The CPU Stand is made up of 25.4mmX1.2mm thick ERW tubes, which is thereafter hooked on with the Side frame . The Tubes are closed with plastic LDPE caps. Nylon Level Adjuster of M8 size are provided to take care of unevenness in Floor. All the Metal parts shall be processed and fabricated in modern Press shop. In case of Welding, all Joints shall be welded. All Metal Parts should be powder coated, before Powder coating all metal parts shall be given anti-rust phosphate treatment. All metal parts shall be epoxy polyester powder coated and backed at 180 C in a converyorised Oven. All steel structural components are processed shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. The powder coated components are on regular basis tested for Scratch resistance test of 4 kgs & for Impact resistance test for 150kgs/cm. Recycled steel will not be accepted. Understructure construction – Width is flush type and depth shall be 540mm

Computer Chair The seat and back are made up of 1.2+/-0.1 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort.(Low BACK) SIZE: 39.0cm. (W) X 32.0cm. (H). SEAT SIZE: 43.0cm. (W) X 41.0cm. (D). The HR Polyurethane foam is moulded with density = 45 +/-2 kg/m cube and hardness load 16+/-2 kgf as per IS:7888 for 25% compression. The frame is made up of 2.54+/-0.03cm X 0.2+/-0.016cm thk M.S.E.R.W. Tube and black powder coated ( DFT 40-60 microns). All steel structural components shall be made from virgin and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted. Seat of the chair should withstand a load of 130 Kg. There should be no deformation or structural change in the understructure on application of above said load

Computer Teachers Table The product should be in complete knock down structure as much as possible/feasible enabling ease in transportation and assemblies within classrooms. The table shall have 1199 (w) X 590 (d) X 750 (H). The worksurface of the table shall be 18 +/- 0.5mm thick Pre Laminated MDF Board (IS14587) top with 2mm thick PVC edge beading on all sides. The understurcture shall be C frame of 0.9+/-0.09 mm thick powder coated 50 microns(+/-10) CRCA MS. The tubular frame shall be of dia. 25.4+/-0.3mm X 1.2+/-0.096mm thick MS ERU round tubes. It shall have 3 drawer unit & shall be 355.5mm W X 559mm D X 433.5mm H, with shell of 0.5+/-0.07 mm thick CRCA MS & drawer tray of 0.5+/-0.07 mm thick CRCA MS & drawe front of 0.8+/-0.1 mm thick CRCA MS & the drawer friction slide shall have 1.2 mm thick CRCA MS & lock shall be of 10 lever cam lock. Handles shall be built in plastic. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled will not be accepted

Computer Teacher Chair The seat and back are made from seasoned wood, caned and finished with synthetic paint (Colour: Black). BACK SIZE: 38.1CM(W) X 39.0CM(H). SEAT SIZE: 38.1cm(W) x 42.4cm(D). The cane is produced from blends of High and Low Density polyethylene. The cane high tensile strength at break=1400 kg/cm2(min.) & Elongation at break=54% maximum. The understructure assembly is a cantilever type frame made of dia. 2.54+/-0.03cm x0.2+/-0.016cm thick M.S. E.R.W. tube and powder coated. (DFT 40-60 microns). Wood used in the manufacturing of seat and back should be free from defects, termite free and after caning should bear a load of 130KG in fitted position. Also there should be no permanent deformation or structural change in the frame structre on apply of this load. At the bottom of frame lugs should be press fitted in punched holes in the frame structure. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted

Stool for Science Lab Overall dimension of the Stool shall be 420mm X 420mm X 600mm (H). Square stool is of fixed height with Pre Laminated MDF top with 2mm PVC edge bending and rest structure is MS powder coated. Structure made of MS square pipe – 32mm X 32mm X 1.6mm thickness. Shoe – Neoprene. Top shall be made of 18mm thick Prelaminated MDF board of dimension- 305mm X 305mm. Finish of metal shall be powder coated

Visitor Chair The seat and back are made from seasoned wood, caned and finished with synthetic paint (Colour: Black ). BACK SIZE: 38.1CM(W) X 39.0CM(H). SEAT SIZE: 38.1cm(W) x 42.4cm(D). The cane is produced from blends of High and Low Density polyethylene. The cane high tensile strength at break=1400 kg/cm2(min.) & Elongation at break=54% maximum. The understructure assembly is a cantilever type frame made of dia. 2.54+/-0.03cm x0.2+/-0.016cm thick M.S. E.R.W. tube and powder coated. (DFT 40-60 microns). Wood used in the manufacturing of seat and back should be free from defects, termite free and after caning should bear a load of 130KG in fitted position. Also there should be no permanent deformation or structural change in the frame structre on apply of this load. At the bottom of frame lugs should be press fitted in punched holes in the frame structure. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted

Steel Almirah Almirah Size shall be 916 mm (W) x 486 mm (D) x 1981 mm (H) Excluding levellers. It shall made of 0.9 mm thk(+/-0.07mm)* CRCA for Shelf, 1.00 mm thk(+/-0.08mm)** High yield strength CRCA for doors and back & 0.9 mm thk(+/-0.08mm)* CRCA for all other components. Construction shall be welded construction. *CRCA 'D' grade as per IS:513. **CRCA 'D' grade high yield strength as per IS:513. Full height Steel Hinged Door shall be provided. Mazak Handle shall be provided having 3 way locking mechanism with shooting bolt arrangement. Height wise 4 nos of Adjustable Shelf shall be provided with Uniformly Distributed Load Capacity per each full shelf is 40 Kg maximum. M10 Screw type leveler with hex plastic base. Outer Finish shall be Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).). Almirah Size shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) Excluding levellers. It shall made of 0.9 mm thk(+/-0.07mm)* CRCA for Shelf, 1.00 mm thk(+/-0.08mm)** High yield strength CRCA for doors and back & 1.00 mm thk(+/-0.08mm)* CRCA for all other components. Construction shall be welded construction. *CRCA 'D' grade as per IS:513. **CRCA 'D' grade high yield strength as per IS:513. Construction shall be welded construction. Locking and Handle – Brass handle, Two way locking mechanism with shooting bolt. Height wise 4 nos of Adjustable Shelf shall be provided with Uniformly Distributed Load Capacity per each full shelf is 40 Kg maximum. M10 Screw type leveler with hex plastic base. Outer Finish shall be Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).). All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted.

Steel Almirah with Glass Door Almirah Size shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) Excluding levellers. It shall made of 0.7 mm thk(+/-0.07mm)* CRCA for Shelf, 0.8 mm thk(+/-0.08mm)** High yield strength CRCA for doors and back & 0.9 mm thk(+/-0.08mm)* CRCA for all other components. Construction shall be welded construction. *CRCA 'D' grade as per IS:513. **CRCA 'D' grade high yield strength as per IS:513. Construction shall be welded construction. Locking and Handle – Brass handle, Two way locking mechanism with shooting bolt. Height wise 4 nos of Adjustable Shelf shall be provided with Uniformly Distributed Load Capacity per each full shelf is 40 Kg maximum. M10 Screw type leveler with hex plastic base. Outer Finish shall be Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).). All steel structural components are processed shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. The powder coated components are on regular basis tested for Scratch resistance test of 4 kgs & for Impact resistance test for 150kgs/cm. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted.

Table for Art/Craft/Culture Room The product should be in complete knock down condition as much as possible/ feasible enabling ease in transportation and assemblies within premesis. Top Size:- 2300x1100 X 750mm (H). The Worktop will be made of 25mm thick MDF Board (IS14587) with Post forming Laminate and balancing Laminate. Post forming on two Longer side and two short Side PVC lipping 2.0mm thk..The under structure is made from 38±0.3 mm X 38± 0.3mm X 1.5 ±0.128 mm thk MS Tube with powder coated 50microns(±10) ( IS 7138 ) at base which are welded and are fixed to top with Chip board Screws. Understructure size 2220mm X 1020mm and 2 additional middile support of 1020mm. The Bottom ends are closed with plastic buffers. The cross members are made from 38±0.3mm X 38±0.3mm X1.5±0.128 mm thk MS Tube at base which are MIG welded and are bolted to Side frames. The Bottom stiffners are connected with Hexagonal bolts. All Fabricated parts which require welding are MIG / Spot welded. The Screw joining Wooden Panels to under structure are Chip Board Screws. All steel structural components shall be made from virgin material and tested conforming to IS: 513/ IS: 10748/ IS: 2062/ IS: 7138. Recycled steel will not be accepted

Display Board P/f 12mm thick silotex board commercial ply backing with fabric duly ironed and pasted on the expossed side and double folded on the edges duly stapled at 25 mm interval with concealed hanging arrangement routered within 12 mm ply. All the sided duly finished with 6mm X 25mm edge beading with rounded edges duly nailed to the 12 mm ply backing pasted with adhesive. All the joints to be mitred and to be at 90 degree Size –900 x 1200 mm