SPECIAL REPAIRS TO ROOF SHEET OF BLDG NO 1 2 20 FENCING PROVN OF ROOF TREATMENT TO BLDG NO 1 3 2 QG AND KOTE CSD AND ADDN / ALTRN OF BLOCK NO 1 J 10 TO 1 J 16 QTR NO 37 to 44 AND 44 to 64 UNDER GE NORTH BINNAGURI

Amount

SCHEDULE A CIVIL WORKS Material and labour for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces finished even and smooth without using extra cement for receiving treatment complete all as specified and directed.

M&L for water proofing treatrment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top :- (a) Applying bitumenous primer @ 0.4 ltrs per Sqm over plastered surfaces of roof incl parapet surface. (b) Over the priming coat laying one layer APP based polymembric membrane of approved manufacturer 3 mm thick weight not less than 3.5 Kgs per Sqm reinforced with non woven polyester febric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 60cm (min) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note :- (i) Laying APP bassed polymenic membrane shall be done torch on methed or as per manufacturer's instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturer's instruction. (iii) Applying two coats of Aluminium paint over APP membrane.) (iv) Treatment shall be done by authorise applicator of the firm (v) Cutting grooves in brick wall 75 mm wide and 65 mm deep and sloping horizontal face of groove with cement mortar 1:3.

Roughening surfaces of old concrete floor/ verticle surface by picking, sweeping clean and washing down with water to remove dust etc.and prepare the surface to receive tiles complete all as specified and directed.

Dismantling of corrugated steel sheets in roof coverings including ridges, removing of unserviceable material from work site complete all as specified and as directed.

Supply and fixed Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Supply and fixed Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in as in ridges, valley, eaves, etc with self tapping screws as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, removing of unserviceable material from work site complete all as specified and as directed.

Supply and fixed rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening .grade Fe-410-W ( Gde-E-250) quality -B complete all as specified.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint (1st quality) over one coat of red oxide Zinc chrome primer complete all as specified.

Dismantling posts or struts (wood, steel or R.C.C.) any section embedded in natural ground , including taking out embedded portion and making good disturbed ground complete all as specified. ( Note :- the vertical height above GL shall be measured for the purpose of payment towards work done)

Excavating in post holes in soft/ loose soil ( or similar holes) each n exc 0.5 cu.m. getting out, returning,filling in and ramming earth or broken rubble mixed with earth around , in layer not exceeding 25 cm, watering and removing surplus soil to a distance n.exc 50 M complete all as specified.

Material and labour for plain cement concrete 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in foundations/mass concrete complete all as specified.

Material and labour for precast reinforced cement concrete type M-25, Design Mix (20 mm graded aggregate) in precast poles, fencing posts, straining or terminal posts, struts etc. for fencing, aaverage sectional area exc 100 and n exc 250sq.cm. With or without chamfered angles and flat, splayed, roundd or mitred tops complete all as specified. Note : Design Mix shall be as per approved Design Mix of CWE/CE's running contracts.

Material and labour for fixing only precast reinforced cement concrete precast poles, fencing posts, straining or terminal posts, struts etc. for fencing, aaverage sectional area exc 100 and n exc 250sq.cm. With or without chamfered angles and flat, splayed, roundd or mitred tops complete all as specified. Note :- Serviceable Material obtained from dismantling here-in-before

Material and labour for Mild steel deformed or twisted bars (TMT) 5 to 10 mm dia , cut to length, bent to shape required, as in stirrups including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or higher complete all as specified.

Material and labour for Mild steel deformed or twisted bars (TMT) 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or higher complete all as specified.

Dismantling of mild steel Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings, including removing of rusted unserviceable wire from work site and keep serviceable wire for reused in safe custody all as directed.

Material and labour for Mild steel Galvanised, (hot dipped galvanised) 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts , including,securing or tying at crossings with and Provision of galvanised mild steel wire , staples or steel pins etc. as directed ( each line wire to be measured) all as directed.

Demolition Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles including removing of demolished materialfrom work site complete all as specified.

Material and labour for brickwork with fly ash bricks, old size, having compressive strength 75Kg sqcm, straight or curved on plan excd 6 M mean radius in built in cement and sand mortar 1:6 complete all as specified.

Material and Labour for rendering 15 mm thick on fair faces of brick or concrete surfaces finishing surfaces even and smooth without using extra cement in Cement mortar 1:4 all as specified and directed.

Material and labour for preparation of newly plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted over one coat of alkaline resistant primer ( before application of cement base paint) of walls including washing floors, etc. , of drops and splashes complete all as specified .

Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations/mass concrete complete all as specified.

Dismantling of chain link wire mesh of any type including removing of rusted unserviceable wire mesh, flat iton, round bar MS, nuts & bolts from work site and keep serviceable wire mesh, flat iton, round bar MS, nuts & bolts for reused in safe custody all as directed.

Supplying only chain link fencing of MS galvanised wire (Hot dipped galvanised), not less than 3 Kg/sqm , made up into mattresses or cages of any mesh size and to any type of standards , rails , straining bolts, etc. including provision of binding wire complete all as specified.

Fixing only chain link fencing to post old and new including line wires, any mesh , size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire all as directed.

Material and labour for Mild steel bars round bar 10mm dia. and over cut to length, bent to shape required,as in fixing of the chain link fence with fencing post including jointing ends of bars by welding, complete all as specified.

Supply and fix mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290-Gde E-165 complete all as specified and directed.

Supply and fixed mild steel framed work such as grills , gratings, and gates of ornamental and intricates design with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290-Gde E-165 including fro portions framed and hung as gates, including pintel, stops complete all as specified and directed.

Material and labour for Mild screw bolts ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut, exc 15 but n exc 22.5cm long and 11 to 15 mm dia. of shank complete all as specified.

Material and labour for preparation of new steel surfaces of any description not otherwise described not exc.10 cm width or girth and applying two coats of synthetic enamelled paint (1st quality) over one coat of red oxide Zinc chrome primer complete all as specified.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint (1st quality) over one coat of red oxide Zinc chrome primer complete all as specified.

Taking down chowkats with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n exc 4 sqm each etc including removing material from work site complete all as specified and directed.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each and including removing material from work site complete all as specified and directed.

Supply and fixing of pressed steel framed for door with one or more rebates including necessary fixing lugs, hinges, lock strike plates, size of frame 125 X 60 mm, complete all as specified and as directed.

Supply and Fixing solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supply & fixing in opening as per specification & drawing and as directed.

Material and labour for 2nd class hard wood for plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, in pieces for replacing one leg or certain portion of dacayed portion without taking down chowkhat or frame by cutting existing length/portion complete including making good disturbed opening by rich mortar in cement mortar (1:4) complete all as specified and as directed.

Supply and fixing of 30mm thick Flush door shutter, solid core construction , with block board core and plywood face panels, commercial type on both faces complete all as specified and as directed.

Supply and fixing of factory made 35mm thick 2nd class hard wood gauged and skeleton shutter open rebated and prepared to received gauge etc (without sash bars) for fly proof door shutter, edges of framing plain, chamfered or rounded, fitted with cut of any mitred beads for securing gauge etc, size of members of shutter as specified in SSR Part-I section 8 clause No.8.23(a) and fitted to chowkats complete all as specified and as directed.

Supply and Fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side as gap insert for top rails bottom rail, panelling of plain colour PVC sheet to be fitting in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drg and as directed.

Supply and fix 100mm size Butt Hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B11 complete all as specified.

Supply and fixing 150 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

Supply and fixing 150 mm size aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified.

Supply and fixing 250 mm long Aluminium alloy. Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

Supply and fixing in repairs factory made steel window with side hung shutters including projecting type hinges with steel handles, and steel peg stay, fixing lugs complete with glazing bar devetailed or welded including one shop coat of red oxide primer compete all as specified and as directed.

Supply and fixing in repairs factory made steel window with side hung shutters including projecting type hinges with steel handles, and steel peg stay, fixing lugs complete without glazing bar devetailed or welded including one shop coat of red oxide primer compete all as specified and as directed.

Supply and fixing in repairs factory made steel ventilators, top hung including hinges, steel peg, fiixng lugs etc complete with or without glazing bars complete all as specified.

Supply and fixed mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290-Gde E-165 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, removing of unserviceable material from work site complete all as specified and as directed.

Supply and fixed rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening .grade Fe-410-W ( Gde-E-250) quality -B complete all as specified.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint (1st quality) over one coat of red oxide Zinc chrome primer complete all as specified.

Material and labour for preparation of untreated new wooden surface of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint, (1 st quality) with a coat of pink primer all as specified and directed.

Hacking out old broken glass ( any thickness , size , quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads upto 1.5 sqm complete all as specified.

Supply and fixing 3 mm thick (nominal) Sheet glass, ordinary quality , in squares, not exceeding 0.50 sqm each each pane fixed with oil putty complete all as specified.

Supply and fixing 3 mm thick figured glass, pin head type and ordinary quality , in squares, not exceeding 0.50 sqm each each pane fixed with oil putty complete all as specified.

Material and labour for plain cement concrete 1:3:6 type C-1 using 20 mm graded crushed stone aggregate as in fixing of hold fast ,bed blocks parapet, cills, coping, filling concrete in PS door frames, filling gaps in between glazed and flyproof steel window, cills and similar works including necessary form work as required complete all as specified and as directed.

Supply and fixed stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fixed in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Demolition Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles including removing of demolished materialfrom work site complete all as specified.

Material and labour for brickwork with fly ash bricks, old size, having compressive strength 75Kg sqcm, straight or curved on plan excd 6 M mean radius in built in cement and sand mortar 1:6 complete all as specified.

Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water, any description etc.including removing of rubbished material from work site complete all as specified.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces , in cement and sand mortar 1:4 using water liquid water proofing compound @ 200 ml per bag of cement or as per manufacturer's instructionscomplete all as specified top surfaces finished even and smooth without using extra cement complete all as specified. (WPC shall be apply in second layer and measured and paid separately)

Material and labour for rendering 5mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 complete all as specified

Material and Labour for rendering 15 mm thick on fair faces of brick or concrete surfaces finishing surfaces even and smooth without using extra cement in Cement mortar 1:6 all as specified and directed.

Supply only Integral liquid water proofing compound conforming to IS-2645-2003 complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), in floors, aprons etc .laid dry or laid dry and pointed including removing of demolished material from work site at any distance outside MD land complete all as specified and directed.complete all as specified.

Material and labour for 18 to 20 mm thick Granite ( of any type) work ( table rubbed and polished) in steps , jambs, pillars, window cills, cooking plateforms and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screeding in CM 1:4 complete all as specified. ( Note Screed bed shall not be measured and paid separately).

Material and labour for Non Skid ceramic coloured tiles (1st quality) 7 to 8mm thick ( square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screeding in CM 1:4 complete all as specified (Note : screed bed shall not be measured and paid separately).

Material and labour for glazed ceramic coloured / digital printed of size (300 x 200 mm / 300 x 450 mm x 7 mm thick ) as in vertical surfaces such as skirting/dado / riser to steps etc conforming to IS - 13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:3) complete all as specified and as directed. (Note : screed bed shall not be measured and paid separately).

Material and labour for preparation of newly plastered surfaces of walls by applying two coats of acrylic based distemper emulsion, white or any tinted including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

Material and labour fo preparation of new plastered or unplastered surafces of ceilings and applying three coats of white wash including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

Material and labour for preparation of newly plastered and applying and applying alkali resistant primer ( before application of cement base paint) and applying two coat of cement base paint complete all as specified.

Taking up or down steel tubing and connections, including cleaning for re-fixing and removal of unserviceable pipe from work site,15 mm bore dia all as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing and removal of unserviceable pipe from work site, 20 mm bore dia all as directed.

Supplying , laying, jointing and testing 15 mm nominal bore Steel water tubes, 'medium grade' ,galvanised , with all fittings ; fixed to walls and ceilings or laid in floors complete all as specified.

Supplying , laying, jointing and testing 20 mm nominal bore Steel water tubes, 'medium grade' ,galvanised , with all fittings ; fixed to walls and ceilings or laid in floors complete all as specified.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)15 mm nominal bore dia, including new fittings complete all as specified ( Note:- Refixing means including cleaning down existing pipes and fittings. )

Cutting chases in brick work, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades,shelves, lintels,etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc.,and making good, cutting not exc 10 cm girth complete all as specified.

Supply and fixed in repair, CP stop cock ( concealed type) long fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified

Supply and fixed in repair PTMT ( Polytetra Methyllene Terephthalate ) Stop cock suitable for 15 mm bore pipe standard of PTMT any colour high pressure screwed for iron pipe and fixed ( Minimum weight 15 mm-90 gms complete all as specified .

Supply and fixed in repair PTMT ( Polytetra Methyllene Terephthalate ) Swivel shower suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed ( Minimum weight 40 gms complete all as specified .

Supply and fixed in repairs vitreous china wash basin (WHB) , white , flat back , size 550 mm x 400 mm (1st quality) including brackets, waste fittings , brass Chromium plated for glazed basins etc. with long screw shanks and fly nuts , flange end embedded in red lead cement , including cutting for and pinning in ends of brackets or erecting stand but but incl providing brackets, waste pipe & CP waste coupling complete all as specified and as directed.

Supply and fixed in repair, 15 mm bore dia of pipe , chromium plated ,pillar taps, fancy type, cast copper alloy , with capstan heads, screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified.

Supply and fixed in repairs vitreous China white Squatting pan ,'Orissa' pattern size 580 mm x 440 mm with integral footrests water closet) with 'P' or 'S' trap front or back inlet complete including lime concrete for bedding, connection to drain pipe and to flushing pipe , anti syphonage pipe etc complete all as specified.

Supply and fixed in repairs low level flushing cistern (dual-flush), 9-10 litres capacity ISI marked embossed moulded from virgin poly propylene including flush pipe complete all as specified and directed.

Supply and fixed in repairs of grating doom 125 mm dia of PTMT (Minimum weight 40gms) with waste holecomplete all as specified.

Supply and fixed in repairs of 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with necessary clamps complete all as specified including taking down old unserviceable pipe including fittings.

Supply and fix PVC (SWR) bends 110 mm bore of any radius without acess door complete all as specified

Supply and fix PVC (SWR) 110mm bore junction single 'T' equal or unequal with access door complete all as specified.

S&F 110mm dia PVC (SWR) branch piece, single ‘Y‘ equal or unequal Complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not specifically provided for , including removing of demolished material from work site at any distance as directed

Material and labour for re-inforced cement concrete type B-1 (1:2:4), using 20 mm graded crushed stone aggregate, as in slabs supported on walls, beams and coloums in floor , roofs , landing, balconies, canopies, deck slab and in shelves and like complete all as specified.

Material and labour for use and waste of form work to flat soffits of suspended slabs, floor slabs, landings and similar work; not exceeding 200 mm thick ( Horizontal or sloping) surfaces finished rough in forms complete all as specified.

Material and labour fo preparation of old plastered or unplastered surafces of ceiling and applying one coat of white wash including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

Material and labour fo preparation of new plastered or unplastered surafces of ceilings and applying three coats of white wash including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

Material and labour for preparation of old plastered surfaces of wall and applying acrylic based distemper emulsion, white or any tinted including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

INTERNAL ELECTRIFICATION Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

Material & Labour for consealed type point wiring with 1.50 Sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed single core multi stranded copper conductor cable of working voltage 1100 volts grade conforming to IS-694 Pt I & II of 2000 drawn through and including PVC conduit of adequate size having a wall thickness not less than 1.5 mm with all accessories (including cutting chases & making good the disturbed surface to its original specification), including provision of 1.5 Sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed single core multi stranded copper conductor cable as earth continuity conductor, connected to main switch / DBs or common earth dolly for one light / fan point / exhaust point controlled by one 5 Amps one way switch complete all as specified and as directed . Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

Material and labour wiring for 5/6 pin 6/16 Amp switch socket combination on independent boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FR earth wire and connecting to earth dolly and brass screws, washers etc. including cutting chases pinning in for concealed conduit wiring and making good of disturbed surface n exc 15 cm girth complete all as specified.

Supply and fixed switch piano flush type, single pole , 6 Amps, one way complete all as specified.

Supply and fixed socket 2 in 1, 5 Pin, 5/16 amps, any type complete all as specified and as directed.

Supply and fixed switch piano flush type, single pole , 15/16 Amps, one way complete all as specified.

Supply & fixed lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

Supply & fixed LED white glass Lamp 1 x 14 Watts, 230V Base-22 complete all as directed.

SHRI ARABINDA GHOSH

SG ENTERPRISE

samrat saw mill and joinery workshop