NEW CONSTRUCTION OF OFFICE BUILDING FOR R AND B SUB DIVISION RANPUR DI BOTAD

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Excavation for foundation upto 1.50 mt depth including sorting out

and stacking of useful materials and disposing the excavated stuff upto 50 mt

1 lead (B) Dense and hard Soil 246.50 Cu.M. 157.16

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

Meter lead.(C) Hard Murrum

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

Meter lead.(D) Soft rock not requiring Blasting

Filling in foundation and plinth with sand in layers of 20 cm. Thickness

4 including watering ramming and consolidating etc. comp. 15.60 Cu.M. 481.80

Filling available excavated Earth (Excluding Rock ) in trench plinth side of

foundation . in layer not excluding 20 cm in depth consolidation each

5 deposited layer by ramming and watering etc. complete 296.30 Cu.M. 136.92

Filling foundation and plinth with murrum or selected soil in layer of 20 cm in

6 thickness including, ramming watering and consolidating etc. complete 478.10 Cu.M. 301.78

Applying general insecticide pest control treatment to floors, cupboards etc

including labour material etc. complete. Using Heptachloride 20 EC. As Per

6113_pests Consentration Weight 0.50 percent is recommended one litre

7 chemical emulsion dillute with 39 liter of water will give. Total dillute 339.50 sqm 39.09

concrentration will be 40 litre inclusive of one litre chemical emulsion

appication 0.5 Litre chemical / Sqm of surface is recommended as per I.S

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

8 graded stone aggregates 20 mm nominal size) and curing complete excluding 17.50 Cu.M. 3805.29

cost of formwork in (A) Foundation and Plinth

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in foundation footings, base of columns and mass

Providing and laying controlled cement concrete M-250 and curing complete

10 including the cost of form work but excluding the cost of reinforcement for 23.20 Cu.M. 7939.28

reinforced concrete work Column Upto Plinth Level

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6-

graded stone aggregates 40 mmnominal size) and curing complete excluding

cost of formwork in (A) Plinth (more than 10 ton)

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work Plinth & Ground Beam

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

13 graded stone aggregates 20 mm nominal size) and curing complete including 35.50 Cu.M. 3887.47

cost of formwork in (A) Plinth Slab

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing and laying controlled cement concrete M-200 and curing complete

14 including the cost of form work but excluding the cost of reinforcement for 4.90 Cu.M. 5488.35

reinforced concrete work in R.C.C. pardee

Providing and laying controlled cement concrete M.200 and curing complete

15 including the cost of formwork and reinforcement for reinforced concrete 19.70 Cu.M. 7906.28

work in (D) Columns (more than 10 ton)

Providing and laying controlled cement concrete M.200 and curing complete

16 including the cost of formwork and reinforcement for reinforced concrete 5.20 Cu.M. 7947.87

work in (D) Columns (more than 10 ton)

Providing and laying controlled cement concrete M-200 and curing complete

17 including the cost of form work but excluding the cost of reinforcement for 26.80 Cu.M. 6356.15

reinforced concrete work Beam

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work Lintel & coping

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

19 reinforced concrete work Lintel & coping 1.90 Cu.M. 7952.42

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

graded stone aggregates 20 mm nominal size) for reinforced concrete

Chhajjas not exceeding 10cm. thickness upto floor two level including

20 finishing the exposed surfaces with cement mortar 1:3 (1-cement, 3 Fine 1.10 Cu.M. 6693.27

sand) to give a smooth and even surface centering and formwork and curing

complete excluding cost of reinforcement.

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

21 reinforced concrete work Slab 34.50 Cu.M. 7019.57

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

22 bending, binding and placing in position complete 27494.00 Kg. 77.29

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

23 bending, binding and placing in position complete 1544.00 Kg. 78.34

Brick work using common burnt clay building bricks having crushing strength

not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1-

24 Cement : 6 -fine sand)(B) Conventional 39.20 Cu.M. 4214.33

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b)

Conventional G.F

(i) Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -

26 coarse sand ) GF (B) Conventional 191.40 Sqm 684.26

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b)

Conventional First floor

Providing and fixing 38mm thick Double Shutter Hardwood flush door of BWP

Grade confirming to IS-710 of approved quality and design including applying

of 1mm thick laminate sheet of approved quality and design to both both

side, all edges shall be covered with 35x12mm first class teakwood bedding

incl. required steel finished brass hardware like hinges, handles, mortice

locks, door stop, stoppers and lock, etc. of approved brands and including

28 extruded aluminum colour anodized "L" section main outer frame size 20.20 Sq.Mt. 4362.19

63.50mm x 38.00mm x 2.50mm (of jindal section 19552 @ Wt.1.1165 kg/mt)

filled with country wood and providing and applying minimum 3 coats of

Melamine Polish and two coats of sealer etc. complete as directed by

Engineer-in-Charge

Providing and fixing 38mm thick Single leaf Shutter Hardwood flush door of

BWP Grade confirming to IS-710 of approved quality and design including

applying of 1mm thick laminate sheet of approved quality and design to both

both side, all edges shall be covered with 35x12mm first class teakwood

bedding incl. required steel finished brass hardware like hinges, handles,

mortice locks, door stop, stoppers and lock, etc. of approved brands and

29 including extruded aluminum colour anodized "L" section main outer frame 8.40 Sq.Mt. 2818.91

size 63.50mm x 38.00mm x 2.50mm (of jindal section 19552 @ Wt.1.1165

kg/mt) filled with country wood and providing and applying minimum 3 coats

of Melamine Polish and two coats of sealer etc. complete as directed by

Engineer-in-Charge

Providing and fixing FRP frame size 125x65 mm and 35mm thick FRP shutter

having extra reinforcement on sides & edges in polish finish. The core of the

shutter & frame is to be filed up with injected polyurethene foam done in

situ alongwith embedded wooden pieces for stiffening & also taking hinges &

fintures. The whole FRP frame & shutter is to be water proof weather proof,

termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S

hinges with necessary screws & alluminium S.S fixtures & fastenings &

fastener sleeve.

Providing and fixing extruded aluminum window having extruded aluminum

Colour anodized section frame main outer size 127mm x 38.10mm x 1.35mm

(of Jindal Section no:2443,@ Wt.1.384 Kg/mt),horizontal Three Track (2

Shutter + 1 Mosqito Net Shutter ) member size 122.20mm x 31.75mm x

1.10mm (of Jindal Section no:8787,@ Wt. 1.205 Kg/mt), vertical member of

size 122.20mm x 31.75mm x 1.50mm (of Jindal Section no:8935,@ Wt.

31 Kg/mt) with sliding shutters of horizontal member size 40mm x 18mm x 23.10 Sq.Mt. 1583.95

1.29mm (of Jindal Section no:8949 @ wt.of 0.456Kg/mt),vertical member of

size 40mm x 18mm x 1.29mm (of Jindal Section no:8947 @ wt.of

0.456Kg/mt/Section 8948,@ Wt. 0.457 Kg/mt) with 5 mm thick transparent

bronze colour tinted float glass with powder coated aluminum fittings and

fixtures and transparent silicon sealant glass fixing to frame as per details etc

complete for window.

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing and fixing standared extruded of alluminium section of size 63mm x

38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour anodized alluminium

32 frame for ventilation with 5 mm thick frosted glass as details etc complete 12.10 Sq.Mt. 1175.56

for Ventilation

Providing and fixing adjustable glass louvers (jalousie type) for ventilation,

consisting of 3 mm thick figured (bajari/obscured) float glass blades of

approved make, securely held in extruded aluminium frames and channels

made from aluminium alloy 6063-T6, conforming to IS:733 and IS:1285. The

aluminium framing shall comprise of top and bottom channels, side supports,

and pivot mechanisms fabricated from standard Jindal or Hindalco sections,

with an average section weight of about 2.00 kg per square metre of louver

area. All aluminium sections shall be anodised to a minimum thickness of

microns in natural or approved colour shade, conforming to IS:1868, with

coating weight not less than 0.40 gm/dm²/μm. The louver blades shall be

33 mounted on stainless steel pivot pins with nylon bushes for smooth 3.30 Sq.Mt. 1016.06

adjustment and operation, and fitted with aluminium operating handles and

locking devices. The assembly shall include all necessary EPDM gaskets, cleat

angles, screws, sealant, and accessories to ensure complete weather-

tightness and smooth functioning. The entire system shall be factory-

fabricated and installed in position at site using dash fasteners, sealants, and

proper alignment tools, including all materials, labour, scaffolding, cutting,

finishing, cleaning, and testing, complete as per manufacturer’s

specifications, architectural drawings, and the direction of the Engineer-in-

Charge. (Anodised aluminium adjustable louver with 3 mm thick figured glass,

complete in allfixing

Providing and respects.)

Safty grills of required pattern for Windows / Door using

16 mm dia M.S polished bars and Rectangular CRC pipes of size 50 * 30* 2mm

34 at Requuired spacing as per design and hold fasting with coach bolts including 576.00 Kg. 116.15

one coat of primer and two coats of mattfinished oil painting etc complete.

P & L 60 X 60 CMS. GLAZED VITRIFIED TILES (GVT)/60 X 60 CMS. GLAZED

VITRIFIED TILES (GVT), 8 mm thick tile flooring over 20 mm (average) base of

cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for light shade.COLOUR &

SAMPLE TO BE APPROVED BY THE ENGINEER IN CHARGE.

Providing and laying Ceramic/Porcelene tiles 60 X 60 CMS, 6mm thick in

flooring Bath,W.C. etc. on a bed of 12mm thick cement mortar 1:3 (1-cement

36 : 3-coarse sand ) finishing with flush pointing in white cement. COLOUR & 29.10 Sq.Mt. 992.15

SAMPLE TO BE APPROVED BY THE ENGINEER IN CHARGE.

Providing and laying Ceramic tiles 30 X 60 CMS. CERAMIC WALL TILES DADO

UPTO BEAM BOTTOM, 6mm thick dado on 10mm thick cement plaster 1:3 (1-

37 cement : 3-coarse sand) and jointed with white cement slurry. COLOUR & 166.80 Sq.Mt. 1023.89

SAMPLE TO BE APPROVED BY THE ENGINEER IN CHARGE.

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing and laying broken chine mosaic flooring for terrace using

mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar

1:3 to plain or slope and to be tempered to bring mortar creme out upto

38 surface using white cement including rounding off junctions and extending 284.00 Sq.Mt. 779.70

them upto 15 cm along the wall,clearing with water and oxalic acid etc. as

Providing and laying Granite Stone slab 25 mm ( Average ) thick incl. Full

molded round front edge laid on 15 mm thick cement mortar 1:3 (1- cvement

39 : 6 coarse sand ) jointed with grey cement Slurry including rubbing and 28.40 Sq.Mt. 2713.55

polishing etc. Complete

Providing and laying mirror polished Black Granite stone slab 18 mm (

Average )thick (Shade of Black Granite Aprooved by Engineer in Charge incl

adhesive used with Sand for Proper Joint with Wall With. Full molded round

40 front edge laid on 10 mm thick cement mortar 1:3 (1- cvement : 6 coarse 65.30 Sq.Mt. 1917.11

sand ) jointed with grey cement Slurry including rubbing and polishing etc.

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of

single or half brick walls for interior plastering upto floor two level and

41 finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) for 981.00 Sq.Mt. 172.00

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) Ground Floor

20mm thick sand faced cement plaster on walls upto height 10 metres above

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

43 sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. 426.50 Sq.Mt. 342.41

Providng and applying two coats acrylic lappy (putty) and two coats of primer

& Wall painting ( two coats) with plastic emulsion paint of approved brand

and manufacture on wall surfaces to give an even brushing the surface free

from mortar droppings and other foreign including Wall painting (two coats)

44 with plastic emulsion paint of approved brand and manufacture on 981.00 Sq.Mt. 123.44

undecorated wall surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign matter and sand

papered smooth.

Providng and applying two coats acrylic lappy (putty) and two coats of Primer

Wall painting ( Two coats) with plastic emulsion paint of approved brand and

manufacture on ceiling & sofit to give an even brushing the surface free from

mortar droppings and other foreign including Wall painting (two coats) with

45 plastic emulsion paint of approved brand and manufacture on undecorated 231.00 Sq.Mt. 128.97

wall surface to give an even shade including throughly brushing the surface

free from mortar droppings and other foreign matter and sand papered

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

46 brushing the surface to remove all dirt, and remains of loose powdered 427.00 Sq.Mt. 120.26

materials etc complete

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

47 or shall be concealed as directed including necessary fittings etc. including 10.00 Rmt. 91.84

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

48 or shall be concealed as directed including necessary fittings etc. including 15.00 Rmt. 72.65

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

49 or shall be concealed as directed including necessary fittings etc. including 30.00 Rmt. 148.12

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing and fixing heavy Handle valve of aprroved brand & Following

internal dia of brass including fixing in pipe lines etc.complete © 25 mm dia

Providing and fixing heavy Handle valve of aprroved brand & Following

internal dia of brass including fixing in pipe lines etc. Complete (E) 40 mm Dia

Providing and fixing Sluice valves IS 14846 with ISI mark of Approved Brand &

52 Follwing internal dia including fixing in pipe lines 40mm 1.00 Nos. 5644.89

Providing and fixing to wall, ceiling and floor galvanised mild steel tubes

(Medium grade) of the following nominal bore, tube, fittings and clamps

53 included making good the wall, ceiling and 40mm 20.00 Rmt. 608.35

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure

polythene pipes of the following outside Dia. Low densidy, complete with

54 special falnge compression type fittings, wall clipsetc. including making good 100.00 Rmt. 280.23

the wall ceiling and floor.(F) 75mm

Providing laying and jointing in true line and level 110 diameter

U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain

and other end socketed with rubbering, & fitting 110mm

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing design

56 with C.I. screwed down or hinged grating 12.00 Nos. 586.27

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing and fixing Screw down Quarter turn bib taps of following size

57 (A) Brass chromium plated screw down Bib tap (I) 15 mm dia 5.00 Nos. 186.83

Providing and Fixing wash basin with pedestal of std. Height with single hole

for pillar tap with C.I or M.S brackets painted white including cutting cutting

58 holes and making goods the same include C.P brass Waste and Waste pipes 2.00 Nos. 2282.60

(A) Vitreous china.

Providing and fixing wash down water closet (Europen type W.C.Pan) with

integral"P" and "S" trap including jointing the trap with soil pipe in cement

mortar 1:1 (1-cement, 1-sand) of Hindware Wall Hung Water Closet

has a slow falling seat cover with an antibacterial and germ free ceramic

surface. with a water saving dual flush. and including jet spray

operated with necessary valve of Jaquar / Cabtree / Plumber including

cutting holes in walls and making good the same connecting the flush bend

with cistern and closet vitreous china etc. complete.

Providing erecting and fixing WHITE COLOUR COATED Tripple coated

Syntex or equivalent PVC. (ISI) mark water tank of reqd

capacity,CONFIRMING TO IS 12704 OF APPROVED COMPANY, each with all

necessary fittings & connection etc. comp on terrace.

Providing and fixing 600 mm x 450 mm bevelled edge mirror of superior

glass mounted on 6 mm thick A.C sheet or plywood sheet or PVC framing and

61 fixed to wooden plugs with C.P brass screw abd washers. 5.00 Nos. 859.41

Providing and fixing C.P. brass towel rail complet with C.P. brass brakets

fixed to wooden plugs with cpbrass screws ( B ) 600 mm X 20mm size

Constructing brick masonary chamber for under ground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in cm. 1:5 C.I. Cover with frame (light duty) 455 mm. X 610 mm.

Internal dimensions, total weight of cover with frame to be not less than

Kgs. weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top slab with

1:2:4 mix(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm.

63 size ) foundation concrete 1:5:10 inside plaster 15 mm. thick with cement 10.00 Nos. 2932.93

mortar 1:3 finished smooth with a floating coat of neat cement on walls &

bed concrete etc. complete.

(I) inside dimensions, 455 mm. x 610 mm. And 450 mm. Deep for single

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling

brickbats with dry masonry work at top for 45cm. height including

covering the top with stone including providing vatas in C.M. 1:3 with

finishing curing etc. complete as directed.

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing throating or plaster drip and moulding to R.C.C. Chhajja.

Providing & fixing Stainless Steel letters of approved design, 75–150 mm

height, 1.5 mm thick, polished finish, fixed with SS pins & epoxy adhesive on

Brick/RCC wall, complete in all respects.

Providing and fixing “Sandwich Platform” type kitchen platform with bottom

support slab and top slab, made of 18–20 mm thick machine-cut, machine-

polished Granite stone slabs of approved shade and colour, including vertical

67 fascia, edge moulding, cutting for sink/hob, making necessary openings, and 1.00 Sq.Mt. 5636.81

providing nosing wherever required, fixed in position with cement mortar 1:4

and approved stone adhesive (epoxy/resin based), complete in all respects.

Providing and fixing C.I. Manhole cover 0.60m x 0.45m size having weight not

less than 35 kgs.

Providing and fixing chiken mesh jali with square of 12.50 X 12.50 mm of

gauge at junction the Brick masonary and reinforcement concrete member

69 including fixing materials sacffolding labour etc.complete 210.00 Sq.Mt. 99.99

Providing and fixing M.S Square pipe 50mm x 50mm x 1.6 mm thickness

weight 4.25 Kg / Rmt suggested by Engineer in Change including including

70 cutting. Bending welding, jointing and fixing on site including painting two 11.00 Rmt. 401.15

coats etc. complete.

Providing, fabricating, supplying, and fixing Stainless Steel (Grade 304) Roof

Access Ladder including treads, balusters, handrails, and necessary fittings,

71 complete with welding, polishing, and erection at site as per drawing and 120.00 Kg 651.45

direction of Engineer-in-Charge.

Providing and fixing Stainless steel (316 Grade) railing made from

anticorrocive 316 grade S S pipe of 50 mm dia (16Gauge) as hand rail with

mm dia pipe for suports at 1.05 mt Vertical supports at equal distance fixed

in RCC, along with londitudnal support with C/C Spacing 38mm dia including

accessories as per detailed drawing as directed, etc. complete including

drilling, fixing, grouting, cleaning, finishing, polishing. As per directed by

engineer in charge.

Providing and fixing roll-formed GI louvres made from 114 mm wide, 0.55 mm

thick GI coil (weight not less than 490 gm/mtr), roll formed to produce

mm effective louvre width, snap-fixed on specially shaped GI

channels/frames. Louvers and channels shall be degreased, passivated and

powder coated to 55 micron (approved shade) after pretreatment, and

73 completed with necessary cleats, fasteners, neoprene washers/EPDM gaskets, 9.80 Sqm 1526.56

drip profile, and sealing. Work includes supply of GI sheet & channels, roll

forming, shop fabrication, powder coating (55 µm), site fixing with dash/bolt

fasteners, trimming, alignment, testing and cleaning, complete as per

drawings and Engineer-in-Charge.

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Earthwork for embankment including breaking clods, dressing with all lead

and lift (including watering and consolidation)(A) From Borrow pits within

74 land width 31.00 Cum 132.37

Providing, laying, spreading and compacting stone aggregates of 63 to 45mm

sizes & Stone screenings Type-A for WBM Grade-II, as per specification

including spreading in uniform thickness, hand packing, rolling with smooth

wheel roller 80-100 kN in stages to proper grade and camber, applying and

75 brooming, stone screening/binding materials to fill-up the interstices of 23.00 Cum 1116.44

coarse aggregate, watering and compacting to the required density grading

as per Technical Specification Clause 405. By Manual Means

Providing and laying cement concrete 1:3:6 (1 Cement : 3- coarse sand : 6-

hand broken stone aggregates 40 mm nominal size) and curing complete

76 excluding cost of formwork in (A) Foundation and Plinth 15.00 Cum 3095.25

Providing and cast in situ Vacuum De-watered Unreinforced cement concrete

of grade M-20-Trimix flooring for average wearing coat / C.C. pavement laid

as directed in approved fixed side form work of steel channel including

vibrating by screedneedle vibrator and leveling with trimix, surface vibrator,

Vacuum De-watering with trimix vacuum pump, floating and further

compaction with trimix skin floater equipped with floating disc, and finished

77 in continous operation including cutting the concrete with concrete cutting 28.00 Cum 6877.46

machine for contraction joints at every 4.00 mtr and expansion joint at

interval of 40 mtr of size 6x12mm to 12x25mm deep or as specified /

providing stripped / broom finish evenly, applying debonding strips, bitumen

primer,bituminous sealant,12 mm dia jute rope and curing etc. complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based

concrete block 30cm length,30cm height and 15cm thick of M250 grade

78 concret as per approved design and including excavation for fixing in proper 79.00 Rmt. 374.92

line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Providing and fixing pre-cast Rubber Dye / Steel dye inter locking concrete

block 60mm thick with grade of concrete M30 pnumatic compressed/ vibrated

mechanically and as per approved design Confirming to IS 15658:2006

79 including 35mm Sand layer for levelling and filling the joint with sand in 56.00 Sqmt 706.93

proper line and level as per Guideline of IRC :SP 63-2018 etc complete.

Drilling of 200 / 215 mm dia. bore well in over burden rocky or loose

collapsible / boulder strata & lowering of 175 / 200 mm dia. UPVC / PVC /

80 ERW casing pipe above 12 meters and up to 40 meters depth by DTH rig 20.00 Rmt 418.14

etc.complete For Zone-I

Drilling of 200 mm dia bore hole by DTH rig in rocky formation in All takuka of

81 Zone III ( o to 350 Mtr ) 50.00 Rmt 489.85

Supply of "U" PVC Casing pipe CM type (B) 200 mm dia

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

83 Providing and fixing bail plug {Bottom Cap } Suitable for 200mm dia. Pipe 1.00 L.S. 830.27

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base

84 frame covered with textured/metallic/white front plate modules erected on 90.00 Pt 485.81

/ in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete CAT-III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected with 6A Modular

type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC /

85 Metallic/Wooden box, single mounting base frame covered with 20.00 Pt. 674.68

textured/metallic/white front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete CAT-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe

86 erected with following type of accessories. [III] For 16A Plug and 16 amp 7.00 Pt. 871.63

switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green) earthing wire from

mcb d b board. (f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame

87 covered with textured / metallic/white front plate modules erected on / in 50.00 Pt. 257.55

wall / ceiling with following type accessories Cat.III

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as

per site situation directed by Engineer In charge. (7) Blank Plate Single cat-III

89 (8) Computer RJ-45 socket CAT-III 18.00 Ea. 160.59

90 (9) 16 Amp. SP one way switch Cat.III 19.00 Ea. 180.79

91 (10) 6/16Amp. Universal socket Cat.III 19.00 Ea. 199.98

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following

size complete to be erected on/in wall or ceiling erected with necessary PVC

92 fittings & Junction boxes fixed with adhesive solution & Clamps with 252.00 Mtr 24.24

following dia of pipes, in approved manner as directed (A) 20mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor

93 FRLS PVC insulated stranded wire of green colour for earth continuity of 450.00 Mtr 82.82

following size (a) with medium class Rigid PVC pipe and accessories (b)

wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected in /

on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

94 stranded wire of green colour for earth continuity of following size (a) with 40.00 Mtr 425.21

medium class Rigid PVC pipe and accessories (i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

95 (Specifically for control panel, relays, power switchgears, motor starters & 25.00 Mtr. 56.56

control wiring) with required size of copper lugs, nuts and bolts if

required.(e) One wire 6.00 sq. mm

(f) One wire 10.00 sq. mm

(i) One wire 35.00 sq. mm

(k) One wire 70.00 sq. mm

Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv

grade ISI marked copper wires of following size to be erected as directed. e)

1.50 Sq.mm 3 core round PVC sheathed

Supplying & erecting approved make LAN cable of following size in existing

100 pipe as per direction [C] CAT - 6 270.00 Mtr 47.47

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary

101 connections as directed 19.00 Ea. 1133.22

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

Decorative call bell Ting-tong box type 250 volts complete erected

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

103 LED driver efficiency > 85 % 4.00 Ea. 165.64

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (A) Tube Light with

integral driver (i) 5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet, Cat-

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet, Cat-lll

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure

die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

105 LED driver efficiency > 85 % 40.00 Ea. 589.84

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)(A) Square/ Circular

shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20,(iii) 16-20 watts, Surge-2 KV, Cat-lll

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet long

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

107 >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( 8.00 Ea. 8453.70

fittings required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (B) Flood Light (IP-

65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (v) above 120 to 160 watts, Cat-lll

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating

up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work

108 on A.C. supply 50 c/s. with all internal connections, spreader tinned copper 3.00 Ea. 6173.12

& complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. at 415 V. having normal current rating

125A. with Fixed thermal & magnetic release suitable to work on A.C.supply

109 50 c/s. with all internal connections, spreader tinned copper & complete 3.00 Ea. 8055.76

erected in existing 16 G.M.S. housing. ICS=100% of ICU only

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

110 work on A.C.supply 50 c/s. with all internal connections, spreader tinned 1.00 Ea. 16221.61

copper & complete erected in existing 16 G.M.S.housing ICS=100% of ICU

Providing and erecting Approved make Earth fault Relay suitable to mount

with inter connection suitable to following size of moulded case circuit

breaker having CT ratio & MCCB rating as following along with shunt trip

111 220V AC. with all internal connections & complete erected in existing 2.00 Ea. 4983.34

M.S.housing.. (2) 125 A -200 A , CT Ratio 1/200

Supplying & erecting approved make Four Pole 415V change over switch

interior for panel mounting with operating mechanism A.C.23 duty confirming

112 to IS for (A)32-40A Cat-lll 1.00 Ea. 2611.86

Supplying and erecting triple pole & neutral 440V / 500V panel mounting

Copper Busbars with four equal Nos. of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

113 carrying capacity, erected with necessary bus bar supports /insulators, main 0.60 Rn mtr. 1961.42

cable socket to each bar, erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

(B) Suitable for 200 Amp. capacity

Supplying KITKAT pattern porcelain cut-out fuse with base of following

115 current capacity erected on existing block board.(v) 100 A. 500 V. 3.00 Ea. 278.76

providing and erecting Miniature circuit breaker single pole 0.5A to 2A system

116 and having breaking capacity 10 KA to be erected in existing box. confirming 8.00 Ea. 270.68

to IS 8828/1996 with ISI Mark Cat.III

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

117 erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III 60.00 Ea. 112.11

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve)

having 10 KA breaking capacity & confirms to IS : 8828 in existing box having

following capacity (B) 40 Amp. Cat-III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve)

having 10KA breaking capacity & confirms to IS :8828 in existing box having

following capacity (b)40 Amp. Cat-III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity, (a) 6 to 32 Amp. Cat.III

121 (b)40 Amp. Cat.III 1.00 Ea. 668.62

122 (c)63 Amp. CAT-III 7.00 Ea. 737.30

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

123 appropriate nos. of MCBs.(The DBs should be used of same company of MCB to 2.00 Ea. 3874.36

be used) suitable for (B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI), (b) sheet steel double door

providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz. having characteristic of

124 quick action & tripping with all advance feature & do not incorporate any 6.00 Ea. 1969.50

electronic component. for following Max. rating erected as directed (i)

Amps.DP Cat. III

Providing and erecting Annealed bare Copper wire 8 to 16 S.W.G.

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover. (A)(approved make OEM has to submit test certificate including value

of earth resistance of installation duly stamped and signed by agency and

126 officer Incharge has to ensure the value of earthing resistane mentioned in 2.00 Nos 4591.46

test Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back

fill Compound :- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Providing & erecting weather proof, dust & vermin proof, floor mounted front

operated indoor type cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements & instruction of engineer-in-

charge with erection of supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber grommets,

rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth

bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with following approved

manufacturers with following size. (A) locally fabricated panel board (i) with

Providing , erecting , fabricating the M.S. structure as per requirement on

site incorporating proper size of M.S. angles,square,round, flats, bars,

channels, sections complete with cutting, welding, grinding & finishing duly

128 painted with one coat of red oxide with erection on site as per direction of 15.00 Kg. 77.77

engineer in charge with necessary grouting, cementing, plastering & finishing

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or

129 in existing trench / pipe of following size of cables (E) 3 1/2 core 95 Sq. 50.00 Mtr. 490.86

mm ( 50 Sq. mm 1/2 core)

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand /

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary

131 clamps or in existing trench / pipe of following size of cables, (C) 4 core 10 180.00 Mtr 140.39

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below

ground across the road crossing or on floor with necessary material in an

approved manner and making the ground as per original.(E)150 mm dia

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting

133 accessories of same material at required depth in existing trench for laying 145.00 Mtr. 62.62

of cable. below ground / road surface for enclosing cable (A)50 mm outer

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with

134 out going tails, insulating tape etc for following size of cables.(D) 3 & 1/2 2.00 Ea. 131.30

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Solder less crimping type Aluminium lugs conforming to IS suitable for cable

of following size evenly crimped with high pressure tool & connected to

136 switchgear terminals with brass/cadmium plated nut bolts in an approved 8.00 Ea. 40.40

manner. (F) 95 Sq.mm.

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite

magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos.

canopies, shackle kit with earthing provision, copper winding, Power factor

not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum

CMM, 350 RPM,230v (tolerance as per IS : 374-2019), THD < 10%, compitible

138 with electronic regulator unit for Speed Control and all remaining accessories 20.00 Ea. 2629.03

including safety pin, nut bolts, washers, temperature rise = 75 degree C

(Max.), suitable for 140 to 285 Voltage and rectifier circuit with surge, over

current and overload protection , 50 Hz, Single phase AC Supply, earthing

etc. Complete as required.[ Make shall be approved by Engineer in Charge]

(A) 1200 mm Sweep (48")

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe

down rod erected duly painted for fan complete with proper insulation

139 without leakage and earthing. 12.00 Mtr. 108.07

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the

RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S.

140 box / Heavy Duty PVC box complete erected concealed in Ceiling with 20.00 Nos 108.07

necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan

Providing & erecting fresh air fan 250 mm dia with square frame make of ABS

142 body with louvers CAT-II 4.00 Nos 1559.44

Supplying & erecting approved make SMC press moulded composite FRP.

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per

143 requirement having locking arrangements with mounting clamp with nuts, 8.00 Ea. 476.72

bolts & washers suitable for erection on pole with cable clamps& earth bolt

of following size of box. (C)150mm x 125mm x 100mm [deep]

Supplying and erecting B class Galvanized iron pipe having smooth finished

bore of the pipe on both ends erected nuts and bolts along the pole / wall

144 shaping the pipe as per site requirement. Pipe dia as following.(A) 25 mm dia 8.00 Mtr 180.79

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

Supplying & erecting approved make IP 55 grade Company fabricated Timer

Panel of following capacity for switch On-Off street lights on time scheduling

basis made from 16G CRCA sheet duly epoxy power painted inside and outside

with hinged doors and locking arrangement consisting of suitable size of

145 Pole MCB and 4 pole contactor (cat-III)with analog time switch, auto manual 1.00 Ea. 13350.18

switch of same make and suitable input and output Bakelite terminals and

with door earthing approved by Engineer in charge. (B) 40 Amp

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling

capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of

the water should drop by 15˚C within a hour, The water cooler should be

comprising of hermetically sealed compressor, fan motor, condensing unit,

water tank surrounded by evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The body of water cooler will be

made from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis water purification system

with M.S. powder coated frame, prefilter housing with 'O' ring presediment

filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi,

147 mention with 40 psi inline type post carbon filter auto low & high pressure 1.00 Ea. 29187.99

switches with following size of storage tank & LPH capacity & erected as

directed [C] 50 Ltr / Hr with 150 psi 2 nos booster pump

Supplying and erecting Direct-on-line, Starter with 15A.rating contractor and

with 4-14A. range, directly operated thermal overload relay in sheet steel

enclosure for 3phase 415V.50 c/s. A.C. motor up to 7.5 H.P.complete

erected on P.W. Block with necessary connection. Cat-lll

Supplying and erecting push button operated fully automatic Star-Delta

starter with 3 Nos. of 15A.rating contactors and directly operated thermal

overload relay having 10-21A range and erected in sheet steel enclosure

149 for 3 phase 415V. 50 c/s. A.C. motors from 7.5 to 15H.P. complete erected 1.00 Ea. 9758.62

on (A) P.W. Block with necessary connection. Cat.III

Providing & erecting open well horizontal mono block pump set with cast iron

body, complete for three phase submersible motor having [C] For 3 HP

150 phase open well horizontal mono block pump set suitable for 85 LPM to 270 2.00 Ea. 15707.52

LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe Cat.II

S.I.T.C. submersible pump set suitable for bore of 150 mm dia or more having

3 phase motor capacity not less than 10 HP with following capacity. Lifting

151 and Lowering taken extra. [A] 10 stage 575 to 480 LPM discharge at 60 to 70 1.00 Ea. 39659.67

mtr head for 65 mm dia delivery pipe Cat.III

Lowering of submersible motor pump set at the depth of following ,complete

with required. Nos. and size of casing pipes erected by means of proper chain

pulley block & pipe wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe assembly filled up with

water, (B)Above 60 mtrs. and Up to 120 mtrs.

Name Of Work : Construction of New Office Building for Road & Building Sub Division At Ranpur, Dist- Botad.

Bill Of Quantity

Estimated Total amount

Estimated Total amount

Sr.no. Description of item Unit rates. as per

In figure estimated

(D)For Open well Horizontal submersible pump set for sump well, (i) 1 HP

153 to 5 HP 2.00 Per Job 856.48

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible

154 Submersible copper cable approved make of following Size. (C) 3 Core x 4 235.00 Mtr. 146.45

Providing Water proof straight Joint in PVC insulated flat flexible copper

cable by using insulating material, water proofing material, & making the

joint complete. (A) Up to 10Sq. mm

Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as

per IS:4984:1995 PE-80 to be erected at road crossing on or floor as directed

156 for laying of cable. The pipes as following size of dia & weight per 6 mtr. (C) 85.00 Mtr. 249.47

63 mm inner Dia.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no

The labour cessshall made.

will be deducted as per prevailing rules i.e. 1% of the work done.

GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C

All Date:11/05/2017

work shall be carried as stated

out as per P.W.D. in Book

therefore in R.C.C. items

other specification where

Division orisasa directed.

change as per actual mix design the

All the columns in the Schedule be filled in ink and the total of the entries in the last column should be struck by the contractor under

Rates quoted include clearance of site (prior commencement of work and at its close) in all respects and hold good for work under all

contractor moisture, weather

exhibit etc. of work, tender amount, specifications as per Govt. circular No. BDG / 3277 / 1657 Dated. 26-4-

In R.C.C. G.R. No. TNC/

there C, Dated.

is change 18-11-91

of grade as directed

mix orchange by the

as per Engineer-in-charge

actual on the work

mix design the difference ofsite for which

of cement contactor shall be

earthquake from rateprovision

resistance of original

works shallrate of star rate

be carried mentioned

cut as in the tender.

per the intruction of Engineer in charge.

The other conditions of Schedule "B" will remain unchanged.

Testing of materials shalll be as per statement atteched with the specification. The materials shall be tested in G.E.R.I. bill of testing

shall be િવભાગ ગાંExecutive

paid the ધીનગરના ઠરાવEngineerમાંકand

of the ૧૧૨૦૦૦/૨૦૧૩/છ

amount તા.shall

put to Tender ૧-૯-૨૦૨૪ થી સાદી માટી

be recovered ઓિડનરી

from (the કલે/અથ

contractor ) અને સોફટ

in running bills

Contractor shallટીeven

percentage. કરવામાં આવે

deduction લ છે .

Deputy Executive Engineer Executive Engineer

( R & B) Sub Division (R & B) Division