8821 REPAIRS TO JOINERY, PLASTERING, PLUMBING, FLOORING, PLINTH PROTECTION AND BRICK WORK ETC. AT AF STATION, BAREILLY

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc. 15cm thickness (below or above ground level) all as specified and as directed.

M&L for 75mm thick cement concrete type C1, 1:3:6 (using 40mm graded stone aggregate) in plinth protection, laid in bay n.exc. 3.00 sq.m each, finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight) complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:2:4) type B1, (using 20 mm graded stone aggregates) as in floor, surface finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on concrete or brick masonry surfaces including raking out joints, hacking for key, scrubbing down with water etc. to receive plaster

M&L for rendering 15mm thick in CM (1:4) on brick or concrete surfaces finishing even and smooth without using extra cement complete including mixing water proofing compound all as specified. [Note: Supply only water proofing compound shall be measured and paid separately]

M&L for 15 mm thick rendering in CM (1:4) mixed with liquid WPC on fair faces of brick or concrete surfaces, finished fair and even at wall height from 3.0m to 8.0 mtr including necessary steel scaffolding complete all as specified and directed. Note :- WPC shall be measured and paid separately.

M&L for 15 mm thick rendering in CM (1:6) in patches on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound.

M&L for 10 mm thick rendering in CM (1:3) on concrete surfaces as on ceiling complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls & applying two coats of cement based paint over one coat of primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of white cement based putty including sand papering the puttied surfaces to form an even and smooth surface, applying a priming coat of exterior primer over new or untreated plastered surfaces, and finally applying two coats of weather proof exterior emulsion paint of five different shades in camouflage pattern (Specific pattern as directed by Engineer-in-Charge) by allowing 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over a coat of primer all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified.

Preparation of old surfaces including brooming down to remove all dust, dirt and loose scales and other foreign matter or steel wire brushing, scrapping down smoke soot, greasy spots, moulds, moss and efflorescent salts and trading oil and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of old decorated surfaces by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying two coat of cement base paint complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of weather proof exterior emulsion paint of five different shades in camouflage pattern (Specific pattern as directed by Engineer-in-Charge) complete all as specified and directed.

M&L for preparation of old decorated surfaces by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of oil bound distemper on wall complete all as specified and as directed.

M&L for preparation of old decorated surfaces by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white wash complete all as specified and as directed.

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for all as specified and as directed

M&L for providing cement concrete type B1, 1:2:4 using 20mm graded aggregate as in lintels up to 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, copings, bed plates etc complete including necessary formwork all as specified.

Demolition of brick work, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as directed.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6m mean radius using old size bricks built in cement mortar (1:6) all as specified.

S&F in repairs PVC (SWR) pipe 110mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as directed.

S&F in repairs PVC (SWR) bends 110mm bore, any radius complete all as directed.

S&F in repairs PVC (SWR) pipe 160mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as directed.

S&F in repairs PVC (SWR) bends 160mm bore, any radius complete all as directed.

Taking down chowkats or frames with shutters (with out taking off shutters from frames) exc. 1.5sq.m. but n. exc. 4sq.m. each all as specified.

Taking down chowkats or frames with shutters (with out taking off shutters from frames) n. exc. 1.5sq.m. each all as specified.

Taking down shutters of any description exc 2 sq.m. each all as specified and directed.

Taking down shutters of any description exc 1 sq.m. and n. exc. 2 sq.m each all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening as per specification & drawing shown on Sl. Page No. 180 of SSR Part-II-2020.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing shown on Sl. Page No. 176 of SSR Part-II-2020.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkat of size 65 x 125 mm, double rebated comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

All as per Item No. 33 herein before but single rebated of size 50x100mm

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Butt hinges and necessary screws shall be paid separately)

S&F Factory made PVC solid panel wire gauzed shutter 35 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling with wire gauze duly wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly as per specification & drawing shown on Sl. Page No. 179 of SSR Part-II-2020.

S&F 35mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both sides all as specified

S&F 35mm thick Second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc size of members as specified in SSR Pt-I, section 8 clause 8.24 (a) all as specified and as directed.

S&F 300mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 250mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 100mm long cold rolled MS butt hinges medium weight.

S&F extruded aluminium handle 125mm long fabricated type anodized all as specified.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section.

S&F 300mm ordinary mild steel rat tail rod pattern springs including roller and roller plate complete

M&L for preparation of wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified

M&L for preparation of old painted steel/ iron surfaces of any description exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and as directed.

M&L for treating small article such as hold fast etc area n.exc 0.1 sq.m each with tar or coal tar black paint complete all as specified and as directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L for mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

S&F steel window with side hung shutters including projecting type hinges with steel handles and steel peg stay with glazing bars dovetailed or welded complete all as specified and as directed.

S&F steel window with side hung shutters including projecting type hinges with steel handles and steel peg stay without glazing bars dovetailed or welded complete all as specified and as directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay with glazing bars dovetailed or welded complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290, Gde-E-165

S&F aluminium handle 150mm long cast type anodized all as specified.

S&F floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ wooden beadings.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ wooden beadings.

S&F 100mm long Butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized and fixed, type C-21

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with wooden beads in square n. exc. 0.5sq.m in each pane all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with wooden beads in square exc. 0.5sq.m in each pane all as specified and as directed.

S&F 3mm thick figured glass, ordinary quality and glazing with oil putty or fixed with wooden beads in square n. exc. 0.5sq.m in each pane all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel/ aluminium frames glazed with putty or fixed with beads

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for 25mm thick cement concrete PCC 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified

M&L for brushing neat cement slurry with 3 kg of cement per sq.m. complete all as specified and as directed.

M&L for non skid coloured ceramic joint free tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11sq.m but n.exc. 0.18sq.m, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 15mm thick screed bed in CM (1:6) complete all as specified.

M&L for double charged, vitrified tiles, coloured, first quality of size 600x600mm, 9 to 10mm thick as in Floors/ skirting, set and jointed in cement slurry, finished with flush pointing in coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. [Note: The colour / shade / design of tiles shall be as approved by GE.]

M&L for glazed digitally printed ceramic tiles of size 300x450mm, 6 to 7mm thick in vertical surfaces of wall, set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 10mm thick backing coat in CM 1:4 complete all as specified.

S&F in repairs 18/19mm thick Pre-laminated particle board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified.

S&F Hasp and staple, 100mm long safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified.

S&F continuous (piano) hinges, mild steel, bright finish or electro-galvanized, width of flaps (when open) 30mm complete as specified.

S&F stainless steel cupboard/ cabinet/ drawer handles 250mm long complete all as directed

S&F Brass lock for cupboard, 2 levers, grade 1, size 65mm complete all as specified

Labour for chamfers, splays, grooves, rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and each groove measured) etc., exc 3mm but n. exc 75mm girth on softwood

S&F high strength deformed TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed.

S&F high strength deformed TMT steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed.

Use and removal of steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete all as specified

M&L for reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like concrete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for

M&L for preparation of new or previously untreated steel/ iron surfaces of any description exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar all as specified.

M&L for 18-20mm thick Udaipur green stone work (table rubbed and polished) in floors, steps, jambs, pillars, window cills, cooking platforms and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone, laid over and including 20mm thick screed bed in CM 1:4 complete including rounding and polishing the edges all as specified and as directed.

M&L for machine cut Kota stone slab flooring 18-22mm thick in treads of stair case etc. over and including 20mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for machine cut Kota stone slab 18-22mm thick in riser of steps, skirting, dado etc. over and including 10mm thick cement screed base in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 1.25mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required and as specified.

M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 410-W (Gde-E- 250), quality-A all as specified.

M&L for Welding in repairs n. exc 2.5cm in length and thickness of metal to be welded n.exc. 6mm all as specified

M&L for Welding in repairs exc. 2.5cm but n. exc 5cm in length and thickness of metal to be welded n.exc. 6mm all as specified

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) sliding type three track (02 glazed shutters and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick tinted glass and mosquito proofing net as detailed below complete all as specified and directed: - (i) Frame section 91.85 X 31.75 X 1.30 mm, section No. 8758 for top and sides rails and 91.85 X 31.75 X 1.20 mm for bottom rail, section No. 8687. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.50 mm, section No. 8820. (iii) Glass 5 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips bearing section No. 4407 and necessary handles, tower bolt etc. as directed. (iv) Stainless steel wire cloth (v) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vi) Locking arrangement and providing Namda rope to make the frames air tight.

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as handles, SS friction hinges etc. complete all as specified and as directed. [Note: Panel inserts like glass & gauge shall be measured & paid separately]

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) door shutters, aluminium section weighing not less than 1.00 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified and as directed. [Note: 1. Weight of builders hardware & rubber beading shall not be considered for payment, however rate quoted shall be deemed to be included for the same. 2. Panel inserts like glass, pre-laminated particle board & gauge shall be measured & paid separately]

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) work for doors, windows, ventilators and partitions (fixed portion) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. complete all as specified and as directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) grill of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F 5.50 mm thick sheet glass (tinted/ reflective type) of any size complete fixed to aluminium frames

S&F 12mm thick pre-laminated particle board, interior grade, pre-laminated on both sides with decorative choice lamination, fixed with screws to timber frame work all as specified.

S&F Mortise lock, brass vertical type, size 65mm, 2 levers all as specified

S&F glass dividing strips 38mm wide, 3mm thick, inserted in position, conform to design all as specified and as directed.

M&L 150mm length of Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring.

S&F in repairs 25mm dia curtain rod mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed by Engineer-in-Charge.

S&F rotational moulded polyethylene water storage tank [cylindrical vertical with closed top], double layered, ISI marked of 500 Ltr capacity with 25mm GI medium grade tank nipple for inlet, outlet, over flow, check nuts for inlet and outlet, hoisted and fixed in position all as specified including disconnecting & taking down existing tanks.

S&F in repairs Ball valves 20mm bore dia, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed [Minimum weight: 210gms] all as specified.

Taking up or down galvanized steel tubing and connections 15mm bore complete all as directed.

Taking up or down galvanized steel tubing and connections 20mm bore complete all as directed.

S&F GI tubes 15mm bore dia medium grade galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F GI tubes 20mm bore dia medium grade galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Refixing old GI tubing 20mm bore dia and connecting in new or old location including cleaning etc. complete all as specified and as directed.

S&F Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) with dia of outlet 75mm complete all as specified.

S&F Cast iron soil, waste and vent pipes 75mm bore, sand cast in any length with or without ears, with cement joints, laid in trenches or in floors all as specified.

S&F Cast iron soil, waste and vent pipes 100mm bore, sand cast in any length with or without ears, with cement joints, fixed to walls all as specified.

S&F of 100mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S&F of 75mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S&F cast iron cowl 75mm

S&F 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

S&F 75mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

S&F Stack clamps for 75mm bore pipe out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

S&F Stack clamps for 100mm bore pipe out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

Dismantling of cast iron or reinforced concrete drain pipes 75/ 100mm dia, jointed in cement mortar and taking out of trenches, if required

S&F in repairs vitreous China squatting pan, Orissa pattern, size 580x440mm, white with integral foot rests, 'P' or 'S' trap including provision of lime concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match complete all as directed.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern) white EWC floor or wall hung type with PVC seat cover including fixing bolts and making connection to flushing cistern, flush pipe etc. complete all as specified and directed.

S&F in repair vitreous china white flat back wash hand basin 550 x 400mm size including CP waste coupling, 32mm dia PVC waste pipe, CI/MS brackets including cutting for and pinning in brackets or fixed with brass screws all as directed.

S&F in repairs PVC valve less, syphonic action type, flushing cistern, dual flush, 10 litres capacity, low level, white, with inlet, ball valve, float and handle, brackets complete including PVC connection and outlet pipe all as directed.

S&F in repairs Stop valves, 15mm bore, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and as directed

S&F PVC connection 15mm size 450mm long with PTMT nuts on both sides.

S&F in repairs wall mixer cast copper alloy, chromium plated for kitchen sink with swan neck bends, fancy type 15mm bore complete all as directed.

S&F in repairs basin mixer cast copper alloy, chromium plated with central hole for WHB, fancy type 15mm bore complete all as directed.

S&F in repairs cast copper alloy, chromium plated hot and cold 15mm dia wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting legs & wall flange complete all as directed [excluding hand & overhead shower].

S&F in repairs Bib taps, 15mm bore, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F corner shelf, fancy type three tier with 5.50mm thick glass mounted on CP brass frame fixed with brass screw & plug, size not less than 450mm complete all as specified.

S&F in repairs brass chromium plated grating doom 100 mm dia complete all as directed.

S&F in repairs brass chromium plated shower rose 125mm dia with swivel joint suitable for fixing to 15mm bore tube all as specified and as directed.

S&F in repairs brass chromium plated Towel rail 'D' type, 600mm long complete all as specified and directed.

S&F in repair brass chromium plated Soap dish complete all as directed.

S&F in repairs 20mm bore gun metal globe or gate valve with iron wheel heads Class-II, screwed both ends for iron pipe all as specified.

Deduct: Amount of Schedule of Credit b/f from Sl. Page No. 17 of tender document i.e. Rs. 54,550.00

S.K.Enterprises (BID ID -3069204)

M/s M Aali construction co (BID ID -3081074)

Ikrar khan & co. (BID ID -3070098)

REHAN CONSTRUCTIONS (BID ID -3070265)