MOEI , Fans, RMO A.C. equipment, pump set at Bungalow of senior officers , Ministers residence, Tilak Marg, Rouse Avenue, Darya Ganj, Chanakya Puri , nearby areas New Delhi

Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group B

Rewiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 Sq.mm. FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel conduit including dismantling as required. (a) Group B

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. (a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

(b) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

(c) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

(d) 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Supplying and drawing of following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. (a) 3 x 1.5 sq. mm

(b) 3 x 4 sq. mm

(c) 3 x 6 sq. mm

(d) 6 x 4 sq. mm

Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 ampers modular socket outlet and 15/16 ampers modular switch, connection, painting etc as required.

Supplying and fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 12 way, Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 Volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) (a) 8 way (4 + 24), Double door

Providing and fixing of following rating and breaking capacity and pole MCCB with thermo magnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. (a) 125 Ampers, 16 kA, breaking capacity TPMCCB (Icu = 100% Ics)

Supplying and fixing of 5 Ampers to 32 Ampers rating, 240/415 Volts, 10 kA, breaking capacity “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

(b) Single pole and neutral

Supplying and fixing of 20 Ampers, 240 Volts, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 Ampers, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying, installation, testing & commissioning of energy efficient 1400 mm sweep size, ceiling fan including wiring the down rod of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheet cover on fan box etc as required.

Supplying, installation, testing & commissioning of energy efficient 1200 mm sweep size, ceiling fan, including wiring the down rod of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable including providing and fixing phenolic laminated sheet cover on fan box etc. as required.

Supply and fixing of 400 mm sweep size, wall mounted fan complete with inbuilt Electronic Regulator, Blade, wire lead with moulded plug top etc as required.

Supplying and installation of Heavy duty exhaust fan of 300 mm sweep size, 900 rpm speed with shutter & louvers in the existing opening alongwith connection, testing & commissioning etc as required.

Supplying and installation of Heavy duty exhaust fan of 380 mm sweep size, 900 rpm speed with shutter & louvers in the existing opening alongwith connection, testing & commissioning etc as required.

Supplying and installation of Fresh Air Fan of 250 mm sweep size (plastic body) in the existing opening connection, testing, commissioning etc as required.

Supplying, installation, testing & commissioning of 20 to 22 watt, 6000K, 1200 mm long energy efficient LED wall mounted light luminaries, extruded aluminum heat sink provided for efficient heat dissipation & integrated electronic driver, suitable to work on 230 volts, AC supply complete with connection etc. with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying, installation, testing & commissioning of energy efficient recessed mounted type 34W to 38W full window glare free opal diffuser LED panel luminaries of size 595mm x 595mm (nominal size) suitable for both Armstrong/POP/Geypsum Board or grid false ceiling fabricated with MS powder coated white CRCA housing including mounting with the help of chain/other suitable method, hanging from the ceiling including connections with 3 x 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required. The Total system Lumen of 34W to 38W LED should be 3600 with minimum system efficacy of 100 lumen /watt colour temperature 5500K to 6500K, power factor>0.95, CRI (Ra)>75, THD <10%, with APFC driver having driver efficiency >85%, operating voltage 150-270 volts with minimum 2.5KV surge protection. The luminaries shall be submitted with LM-80 report with a life of 50000 Hours @ L-70 and LED photo biological safety report conforming to IEC 62471 & LED source manufacturer and LM-79 report from NABL accredited Lab. The LED chip should be of Cree, Nichia, Philips Lumiled, Osram, Edison.

Supplying, installation, testing & commissioning of LED Bollard Fitting of system wattage 8W to 11W of Multiple LED with lens optics and IP65 pressure die-cast aluminum housing for effective thermal management. Total system Lumen of 8W to 11W LED should be 500 or above in cool day light (5700K to 6500K), power factor>0.90, CRI>70 complete with mounting brackets & accessories including making necessary foundation as required with connections

Supplying, installation, testing & commissioning of energy efficient LED flood light luminaries of system wattages 90 to 100 complete with accessories on the existing boundary wall including connections with 1.5 sq mm FRLS PVC insulated copper conductor single core cable complete etc as required The LED luminaries should confirm the following technical specifications :- a. Type of LED: High power LEDs Nichia/Osram/Cree/Philips b. driver efficiency >85% c. System Efficacy >100lm/w d. color Index(CRI) Ra>70 e. Color Temperature (CCT) Cool white:5500°-6500°K f. Input Voltage. 140-270V AC g. Frequency Range 50-60Hz h. Power Factor(PF) > 0.95 i. Surge protection = 4.0KV j. Total Harmonic Distortion(THD)< 10% k. Working Environment 0°C to 50°C;10%-90%RH l. Working lifetime: >50000hrs m. IP Rating :- IP: 65/ IP: 66 n. Housing and finish :-epoxy powder coated die cast aluminum housing with elegantly designed heat sink for efficient thermal management and to excellent corrosion resistant, cable gland P49 is provided at cable entry cover & high quality toughned glass.

Supplying & fixing of 9 watts fancy single wall mounted decorating light luminaries with lamp complete with connection etc as required.

Supplying & fixing of 9 watts fancy double wall mounted decorating light luminaries with lamp complete with connection etc as required.

Supplying & fixing of energy efficient 10 watts wall mounted mirror LED luminaries (600mm) suitable to work on 230Volts, AC supply complete with connection & testing etc as required.

Supplying, installation, testing & commissioning of energy efficient surface mounted type 6W to 10W glare free opal diffuser LED Bulk Head luminaries including connections with 3 x 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required. The Total system Lumen of 6W to 10W LED should be 550 with minimum system efficacy of 100 lumen /watt, colour temperature 5700K to 6500K, power factor>0.95, CRI (Ra)>75, THD <10%, with APFC driver having driver efficiency >85%, operating voltage 150-270 volts with minimum 2.5KV surge protection. The luminaries shall be submitted with LM-80 report with a life of 50000 Hours @ L-70 and LED photo biological safety report conforming to IEC 62471 & LED source manufacturer and LM-79 report from NABL accredited Lab. The LED chip should be of Cree, Nichia, Philips Lumiled, Osram, Edison

Supplying, installation, testing & commissioning of LED Post top lantern luminaries of system wattages of 40 to 50 multiple LED with lens optics and IP:65 pressure die-cast aluminum housing for effective thermal management, total system lumen efficiency should be >90 lumen/watt or above in cool day light (5700K to 6500J), power factor>0.90, CRI>70 complete with mounting brackets on gate including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. The luminaries shall be submitted with LM-80 report with a life of 50000 Hours @ L-70 and LED photo biological safety report conforming to IEC 62471 & LED source manufacturer and LM-79 report from NABL accredited Lab. The LED chip should be of Cree, Nichia, Philips Lumiled, Osram.

Supplying & fixing of energy efficient 15 watts LED down lighter luminaries in the surface including connection, testing etc. as required The Total minimum system efficacy of luminaries should be minimum 80 lumen /watt colour temperature 5500K to 6500K, power factor>0.95, CRI (Ra)>75, THD <10%, with APFC driver having driver efficiency >85%, operating voltage 150-270 volts with minimum 2.5KV surge protection. The luminaries shall be submitted with LM-80 report with a life of 50000 Hours @ L-70 & LED source manufacturer and LM-79 report from NABL accredited Lab. The LED chip should be of Cree, Nichia, Philips Lumiled, Osram.

Providing, replacement, installation, testing & commissioning of single phase, 01 HP capacity centrifugal mono-block pump sets, 1500-RPM, 25mm X 25 mm suction & delivery capable to deliver 880 LPM at the head of 45 meters alongwith making good the damaged foundation including connection etc complete as required.

Supplying, laying and fixing of 3 x 6 sq.mm PVC insulated and PVC sheathed/ XLPE aluminum conductor armoured power cable of 1.1 KV grade etc as required. in the following manner: (a) On wall surface

(b) Direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Dismantling & less credit for following electrical accessories etc. complete as required under buy back arrangement (a) SPDB/TPDB with accessories.

(b) 1200/1400mm sweep size ceiling fan

(c) assorted Wall/Fresh Air Fan size

(d) 380/300mm sweep size, Exhaust Fan

(e) LED luminaries

(f) 1 HP capacity centrifugal mono-block pump set

(g) Assorted PVC copper cable.

(h) Assorted XLPE aluminum cable

tej Enterprises

M/s Cholia Electric works