Restoration of Old Rest Room and Construct New Inspection Bunglow (Sarswati Bhavan) At Mukteshwar Dam Site, Mukteshwar Ta. Vadgam Dist. B.K.

BILL OF QUANTITIES

Name of Work :- Restoration of Old Rest Room and Construct New Inspection

Bunglow (Sarswati Bhavan) At Mukteshwar Dam Site,

Mukteshwar Ta. Vadgam Dist. B.K.

(A) Percentage Rate Tender (Up to INR 50 Cr. )

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

1 Excavation for foundation up to 1.5 m depth

including sorting out and stacking of useful materials

and disposing off the excavated stuff up to 50 Meter

lead.(A) Loose or soft soil

2 Excavation for foundation up to 1.5 m to 3.00 mt

depth including sorting out and stacking of useful

materials and disposing off the excavated stuff up to

50 Meter lead.(A) Loose or soft soil

3 Filling in foundation and plinth with murrum or

selected soil in layers of 20cm. thickness including

watering, ramming and consolidating etc. complete.

(more than 10 ton)

4 Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers

not exceeding 20 cm. in depth consolidating each

deposited layer by ramming and watering.

5 Providing and laying controlled cement concrete

M.150 for curing complete excluding cost of

formwork and reinforcement for reinforced concrete 18.00 CMT 3806.990

work in (A) Foundations, footings,Base of columns

and Mass concrete

6 Providing TMT Bar FE 500D reinforcement for R.C.C.

work including bending, binding and placing in 20645.00 Kg. 77.560

position complete upto all floor level.

7 Providing and laying controlled cement concrete M-

250 with curing complete, including the cost of

formwork but excluding the cost of reinforcement 44.00 CMT 4451.700

for reinforced concrete work in Foundation footing

base of columns and mass concrete. (For any size)

8 Providing and laying controlled cement concrete M-

250 and finishing smooth with cuing etc. complete

including the cost of formwork but excluding the cost 10.00 CMT 7242.000

of reinforcement for reinforced concrete work in

columns up to plinth level.

9 Providing and laying controlled cement concrete M-

250 and curing complete including the cost of

formwork but excluding the cost of reinforcement

for RCC work in Ground beam and Plinth Beam.

10 Providing and laying cement concrete 1:3:6 (1-

Cement : 3- coarse sand : 6- hand broken stone

aggregates 40 mmnominal size) and curing complete 18.00 CMT 2949.480

excluding cost of formwork in (A) Foundation and

11 Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:6. (1-

Cement : 6 fine sand) (b) Conventional

12 Providing and laying controlled cement concrete M-

250 curing complete including cost of Formwork but

including cost of reinforcement for wall caps/coping.

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

13 Carring out plinth treatment to post construction /

existing structure by spraying chemical solution for

termite control treatment including labour and

material consistment with I.S.I specification. Using

Chlordene and Chiorpurfiles 20 EC. As Per

_paret-II Consentration Weight one percent is 120.00 SMT 86.000

recommended i.e one litre 20 EC chemical emulsion

with 19 liter give 1 % concrentration inclusive of one

litre chemical emulsion appication at the rate of

Litre chemical / Sqm of surface is recommended as

14 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement 8.00 CMT 7684.370

for reinforced concrete work in Columns, Pillars

posts and struts at Ground floor.

15 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement 7.00 CMT 7723.900

for reinforced concrete work in Columns, Pillars

posts and struts at First floor.

16 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement 12.00 CMT 6245.490

for reinforced concrete work in Beam at Ground

17 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement

for reinforced concrete work in Beam at First floor.

18 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement

for reinforced concrete work in Slab at Ground floor.

19 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement

for reinforced concrete work in Slab at First floor.

20 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement 4.00 CMT 7998.540

for reinforced concrete work in Lintel at Ground

21 Providing and laying controlled cement concrete

M.250 and curing complete including the cost of

formwork but excluding the cost of reinforcement

for reinforced concrete work in Lintel at First floor.

22 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement 3.00 CMT 7309.330

for reinforced concrete work in Staircase at Ground

23 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement 1.00 CMT 6540.190

for reinforced concrete work in Chhajja at Ground

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

24 Providing and laying controlled cement concrete

M.200 and curing complete including the cost of

formwork but excluding the cost of reinforcement

for reinforced concrete work in Chhajja at First floor.

25 Providing and laying controlled cement concrete

M.150 for curing complete including cost of

formwork but excluding the cost of reinforcement 2.00 CMT 4782.890

for reinforced concrete work in columns at Second

26 Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:6. (1- 53.00 CMT 4451.530

Cement : 6 fine sand) (b) Conventional (Ground

27 Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:6. (1-

Cement : 6 fine sand) (b) Conventional ( First Floor )

28 Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:6. (1- 5.00 CMT 4534.930

Cement : 6 fine sand) (b) Conventional (Second Floor

29 (i) Half brick masonry in common brunt clay

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement 12.00 SMT 677.490

: 4 -coarse sand ) in foundation and plinth (B)

Conventional ( Ground Floor )

30 (i) Half brick masonry in common brunt clay

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement 31.00 SMT 683.730

: 4 -coarse sand ) in foundation and plinth (B)

Conventional ( First Floor )

31 Charges for making holes in brick walls / RCC with

or without plaster / tiles with mechanical cutter

like HILTI etc. Including disposing the debris and

finishing the same as per requirements.

Measurement of holes will be taken per no. of holes 15.00 NOS 1035.000

drilled as per following range of diameters. Making

of holes by hammer and chisel will not be

considered in this item. For Diameter of holes up to

32 Charges for making holes in brick walls / RCC with

or without plaster / tiles with mechanical cutter

like HILTI etc. Including disposing the debris and

finishing the same as per requirements.

Measurement of holes will be taken per no. of holes 10.00 NOS 863.000

drilled as per following range of diameters. Making

of holes by hammer and chisel will not be

considered in this item. For Diameter of holes up to

33 Providing and fixing teak wood window &

ventilation fully glazed with wooden frame and

shutters, complete as per design and direction of the

Engineer/Architect. Frame & Shutter Material: First-

class seasoned teak wood. Section size of frame: As

per approved drawing (typically 100 mm × 75 mm

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

or as directed). Shutters with vertical and horizontal

members (styles and rails) of adequate thickness

(typically 40 mm to 50 mm). Finish & Joinery:

Properly planed, smooth surface, free from defects,

warping, or knots. All joints to be tight, with adhesive

and wooden dowels/tenons for rigidity. Brass/SS

hinges, handles, and tower bolts to be provided.

Glazing: 5 mm thick clear float glass, set with

wooden beads and nails. Glass panels properly fitted

without gaps or looseness.

Polishing: Two coats of melamine/PU polish over

one coat of wood filler, rubbed and finished to

smooth texture, highlighting natural grains.

Installation: Fixed in masonry opening with proper

holdfasts and screws. All edges aligned and sealed

with approved quality sealant.

34 Providing and fixing first-class seasoned teak wood

partly paneled and partly glazed decorative door

shutter including teak wood frame, conforming to

approved architectural design and drawings,

complete in all respects.

Specifications:

Frame: Made of first-class seasoned teak wood. Size

of frame sections not less than 100 mm × 75 mm (or

as per drawing). Joints to be mortise and tenon,

glued and pinned with teak wood/wooden dowels.

Shutter: Thickness of shutter 35–40 mm (or as per

design). Lower portion to be provided with solid

teak wood panels, properly tongued and

grooved.Upper portion to be provided with 3 mm–5

mm thick glass panes, fixed with teak wood glazing

beads.Styles and rails made of solid teak wood,

section as per approved design. Finish &

Workmanship: All exposed surfaces to be planned,

smooth, and sanded. All members to be free from

knots, cracks, decay, or sap. Proper polishing /

painting to be carried out as specified. Fittings:

Standard oxidized brass/stainless steel hinges,

handles, tower bolts, and other necessary hardware.

Fittings fixed with screws, not nails.

35 Provoding and fixing flush door shutters, solid core

construction with frame of first class hardwood with

cross board and face veneer or plywood face panels,

including anodised alluminium butt hinges with

necessary screws. (A) Non-decorative type and block 10.00 SMT 2678.000

board core anodised alluminium butt hinges in flush

door shutters 35 mm thick. (B) Apply front side 1mm

decorative laminate and back side 0.80mm white

laminate with wood adhesive as directed by EIC.

36 Providing and fixing FRP frame size 125x65 mm and

35mm thick FRP shutter having extra reinforcement

on sides & edges in polish finish. The core of the

shutter & frame is to be filed up with injected

polyurethene foam done in situ alongwith embedded

wooden pieces for stiffening & also taking hinges &

fintures. The whole FRP frame & shutter is to be

water proof weather proof, termite proof &

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

resistance to mild acid/alkali. Rates are to be

inclusive of S.S hinges with necessary screws &

alluminium S.S fixtures & fastenings & fastener

37 providing and fixing dead lock of approved 3 lever in

doors with necessary screws and as per drawing,

complete as approved by architect or engineer in

38 providing and fixing S.S. Pipe Handle for door 30 Cm

size o ASIS 316 Grade finish push -pull handles in

pair of two, with necessary screws etc. Complete, as

per drawing as approved by architect or engineer in

charge. Two pieces of handle shall be considered as

one no. for measurement & payment.

39 Fixing Metallic tower bolts of sizes with necessary

screws etc. complete

40 Providing & fixing 75 mm S.S. 316 satin finish baby

latch (kitch or equivalent approved make ) with

indication of occupancy ( flat / round ) of kitch of

equivalent with necessary screws etc. Complete as

approved by Architect or Engineer-in- charge with

indication of occupancy.

41 Providing & fixing 75 - 100 mm white PVC door

buffer with necessary screws etc. Complete as 5.00 NOS 40.000

approved by Architect or Engineer-in-charge.

42 Providing fabricating, erecting and fixing of M.S.grill,

fabricated from m.s. plat, angles, tees, spacebar,

round bar, pipes etc. complete as per Architect detail

& Drawing including applying one coat of red oxide 1748.00 KG 109.000

& two coat synthetic enamel paint etc complete. As

per Architect instructions and drawing or as directed

by engineer in charge.

43 providing and fixing stainless steel railing made from

anticorrosive 304 grade s.s. pipe of 50mm dia (16

gage) as hand rails.s. 304 grade baluster as vertical

support fixed in r.c.c. slab at 1.00 T0 1.20 mt c/c and 12.00 RMT 2402.840

height should be 900 mm including accessories as

per detail drawing as directed etc complete as

approved by engineer in charge

44 Providing 10mm thick cement plaster in single coat

on brick/concrete walls for interior plastering upto

floor two level and finished even and smooth in 126.00 SMT 137.270

(i)Cement mortar 1:3 (1-cement:3-sand). Ground

45 Providing 10mm thick cement plaster in single coat

on brick/concrete walls for interior plastering upto

floor two level and finished even and smooth in

(i)Cement mortar 1:3 (1-cement:3-sand). First Floor

46 Providing 15mm thick cement plaster in single coat

on Rough (Similar)side of single or half brick walls

for interior plastering upto floor two level and 463.00 SMT 163.390

finished even and smooth in (ii) Cement mortar 1:4

(1-cement :4-sand) Ground floor

47 Providing 15mm thick cement plaster in single coat

on Rough (Similar)side of single or half brick walls

for interior plastering upto floor two level and

finished even and smooth in (ii) Cement mortar 1:4

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

(1-cement :4-sand) First floor

48 Providing and fixing 24 gauge - GI chicken wire mesh

(PLASTER MESH OF AMAX INTERNATIONAL) at the

junction of masonry work and RCC work or on any

other place as directed to receive plaster including 42.00 SMT 286.010

fixing with galvanized nails, raw plugs at all heights

plinth level- including scaffolding etc complete as

49 20mm thick sand faced/mala cement plaster on

walls upto height 10 metres above ground level

consisting of 12mm thick backing coat of C.M. 1:3 (1- 701.00 SMT 317.520

cement : 3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) etc. complete.

50 Finishing wall with water base primer (one coat) and

weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even

shade after thoroughly brushing the surface to

remove all dirt, and remains of loose powdered

materials.etc complete.

51 Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall

surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth and

painting (two coats) with plastic emulsion paint of

approved brand and manufacture on wall surface to

give an even shade including throughly brushing the

surface free from mortar droppings and other

foreign matter and sand papered smooth.

52 Applying two coats of putty & two coats of primer of

approved brand and manufacture on new ceilings

and sloping roof surface to give an even shade

including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand

papered smooth and Wall painting (two coats) with 209.00 SMT 128.020

plastic emulsion paint of approved brand and

manufacture on ceilings and sloping roof surface to

give an even shade including throughly brushing the

surface free from mortar droppings and other

foreign matter and sand papered smooth.

53 P & L 24" x 24" vitrified 8 mm thick tile flooring over

20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with

color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for

54 Providing and laying Vitrified tiles 8 to 10 mm thick

24'' x 24'' in dedo on 10mm thick cement plaster 1:3

(1-cement : 3 coarse sand) and jointed with white

55 P & L 600 x 1200 vitrified 8 mm thick tile flooring

over 20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on 190.00 SMT 1860.000

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for

56 Providing and laying polished Kota stone slab

flooring over 20mm (Average) thick base of cement

mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5

(1-Lime putty :1.5 - coarse sand) laid over and 6.00 SMT 1008.790

jointed with grey cement slurry mixed with pigment

to match the shade of slab including rubbing and

polishing etc. complete. (A) 25mm thick

57 Providing and laying Vitrified granite tiles 8mm to

10 mm thick in skirting risers of steps and dado on

10 mm. thick cement plaster 1:3 (1 cement : 3 coarse 13.00 SMT 1576.630

sand) pointing in white cement and jointed with

white cement slurry.

58 Providing & fixing granite stone average 18 mm thick

(16-18 mm) machine-cut & machined polished stone

in treads of steps, sill, copings, parapet top, window

sill, planter top, and such other locations, laid on

mm(average) thick cement mortar 1:4 (1

cement:4coarse sand) and jointed with Super flex

guranted fixing solution by kerakoll mixed with

pigment to match the shades of the slabs, including 70.00 SMT 3531.000

rubbing and polishing complete. The Stone used

should be in one single long piece up to 3000 mm as

per drawing or as directed by Engineer-in-charge.

The exposed projected edges shall be of uniform

thickness and of uniform projection including

molding , chamfering, rounding, polishing complete.

as directed by EIC.

59 Providing & fixing sandwich type average 18 mm

thick (16-18 mm) machined polished GRAINITE

stone molded door frame of inner trip 130mm

X18mm wide and outer trip 150mm X 18mm wide

jointed with Super flex guranted fixing solution by

kerakoll mixed with pigment to match the shades of

the slabs, including rubbing and polishing complete. 69.00 RMT 1102.000

The Stone used should be in one single long piece as

per drawing or as directed by Engineer-in-charge.

The exposed projected edges shall be of uniform

thickness and of uniform projection including

molding , chamfering, rounding, polishing complete

as directed by EIC.

60 Providing and laying cement concrete flooring 1:2:4

(1- cement : 2-coarse sand : 4-graded stone

aggregate 20mm nominal size) laid in one layer and 109.00 SMT 296.030

finished with a floating coat of neat cement. (A)

61 Providing and laying broken china mosaic flooring

for terrace using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar

creme out up to surface using white cement

including rounding off junctions and extending them

up to 15 cm along the wall, clearing with water and

oxalic acid etc. as directed.

62 Providing erecting and fixing double coated ISI water 2000.00 LITER 3.910

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

tank of required capacity each with all necessary

fittings and connection etc. complete on terrace.

63 providing and fixing (A) White glazed vitreous

chinaware extended wall mounted cantilever type

European type water closet with Hydrolic seat cover,

with (B) flushing tank constellation cistern with

cistern fittings, CI chair bracket with rag bolt and GI

12mm rag bolt with nut and metal washer etc.

including supply and fixing of (C) 1 no CP heavy duty

angle cock with CP wall flange with CP brass inlet

connection with integral P or S trap including cutting

and making good the wall and floor as under with

supported on CI wall brackets and (D) flush cock

mm etc. complete to the satisfaction of EIC.

64 providing and fixing (A) white glazed vitreous

chinaware European type water closet with seat

cover, with , CI chair bracket with 12mm rag bolt nut

and metal washer etc. including supply and fixing of

(B) 1 no CP heavy duty angle cock with CP wall

flange with CP brass inlet connection with integral P

or S trap including cutting and making good the wall

and floor as under with supported on CI wall

brackets and (C) flush cock etc. complete to the

satisfactionof EIC

65 providing and fixing (water closet squatting Pan

(Indian type W.C. Pan) size 580mm (A) Vitreous

China.(I) Long pattern = White colour inlet

connection with integral P or S trap including cutting 1.00 NOS 1583.000

and making good the wall and floor as under with

supported on CI wall brackets and (B) flush cock

etc. complete to the satisfaction of EIC

66 providing and fixingProviding and fixing washbasin

with single hole for pillar tap with C.I. or M.S.

brackets painted white including sutting holes and

making good the same including fittings.(a) Vitreous

China:(ii) Flat Back washbasin 550 mm x v 400mm

size. (i) In white colour. (b) 32mm CP cast brass

bottle trap heavy casted, with 250mm long wall

connection pipe and wall flange with rubber adopter 6.00 NOS 5030.000

for waste connection and one 40mm dia waste

coupling. (c) 1 no heavy quality CP brass angle cock

with wall CP flange (d) 15 mm size. pillar cock with

fitting complete. (e)1 no 15mm NB heavy quality CP

brass inlet connection with unions end. the

supporting bracket shall be painted with 3 coats of

approved paint of approved shade etc complete

67 providing and fixing screw down brass chromium

plated heavy quality two way bib-tap on water

supply pipe lines of 15mm dia with or with extension 6.00 NOS 2442.000

piece but with a flange etc. complete to the

satisfaction of EIC.

68 providing and fixing 15 mm knob cp brass heavy

quality wall or floor mounted sink tap, with cp wall

flange, casted spout of three way etc. complete to

the satisfaction of eic.

69 Providing and fixing 600mm x 450mm bevelled edge

mirrror of superior glass mounted on 6mm thick A.C.

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

sheet or plywood sheet and fixing to wooden pluge

with C.P. brass screws and washers.

70 Providing and fixing C.P. brass towel rail comlete

with C.P. brass brackets fixed to wooden plugs with 6.00 NOS 610.320

C.P. brass scews.(B) 600mm x 20mm size.

71 providing and fixing ss or brass chromium plated

double robe hook as per the design and 6.00 NOS 935.000

specifications etc., complete to the satisfaction of eic.

72 Providing and fixing toilet paper holder.(A) C.P.

73 providing and fixing hand shower (health faucet)

with cp flange with 8 mm dia., 1 m long pvc tube and

wall hook with fitting . as approved by the

74 Providing and fixing Urinal of approved quality

including connection with trap and with integral

longitudinal flush pipe.(A) Squating plate pattern

white earthenware 550mm x 300mm.

75 providing and fixing to wall, ceiling and floor, SWR

quality, heavy duty 6KG/RMT pvc pipes of finolax /

astral or equivalent make as approved by eic,, open

laid for soil / waste / rain water etc complete, with

necessary specials, bends, such as Y junction T

junction (both single and double) including plugs,

shoes, cowls flange compression type fittings, wall

clips, in proper line and level with necessary support

like split clamps of chilly make 3mm minimum 80.00 RMT 427.000

thickness fixed with approved anchor fasteners ,RCC

or brick pedestals or battens if necessary to wall,

ceiling and floor, open laid complete jointing with

suitable grade of good quality solvent cement (as

recommended by the manufacturer) including

testing, cutting, making good the wall, ceiling and

floor, etc complete to the satisfaction of EIC of the

following OD. 110 mm 6 Kg.F/cm

76 providing and fixing to wall, ceiling and floor, SWR

quality, heavy duty 6KG/RMT pvc pipes of finolax /

astral or equivalent make as approved by eic,, open

laid for soil / waste / rain water etc complete, with

necessary specials, bends, such as Y junction T

junction (both single and double) including plugs,

shoes, cowls flange compression type fittings, wall

clips, in proper line and level with necessary support

like split clamps of chilly make 3mm minimum

thickness fixed with approved anchor fasteners of

HILTI equivalent ,RCC or brick pedestals or battens if

necessary to wall, ceiling and floor, open laid

complete jointing with suitable grade of good quality

solvent cement (as recommended by the

manufacturer) including testing, cutting, making

good the wall, ceiling and floor, etc complete to the

satisfaction of EIC of the following OD. 75 mm

77 providing and fixing to wall, ceiling and floor, SWR

quality, heavy duty 6KG/RMT pvc pipes of finolax /

astral or equivalent make as approved by eic,, open

laid for soil / waste / rain water etc complete, with

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

necessary specials, bends, such as Y junction T

junction (both single and double) including plugs,

shoes, cowls flange compression type fittings, wall

clips, in proper line and level with necessary support

like split clamps of chilly make 3mm minimum

thickness fixed with approved anchor fasteners of

HILTI equivalent ,RCC or brick pedestals or battens if

necessary to wall, ceiling and floor, open laid

complete jointing with suitable grade of good quality

solvent cement (as recommended by the

manufacturer) including testing, cutting, making

good the wall, ceiling and floor, etc complete to the

satisfaction of EIC of the following OD. 160 mm

78 Providing laying and jointing in true line and level

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

79 Providing laying and jointing in true line and level

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

80 Providing laying and jointing in true line and level

40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

81 Providing laying and jointing in true line and level

50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

82 Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water

of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

floor etc. complete. [A] 15 mm.

83 Providing and fixing concealed center point to wall

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water 20.00 RMT 251.310

of following dia. nominal bore tube fittings and

clamps including making good the wall, ceiling and

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

floor etc. complete. [C] 25 mm.

84 Providing cement vata (10 cm x 10 cm size) quarter

round in cement mortar 1 :1 including neat cement

finishing watering etc. complete as per architect

85 Providing and fixing pre-cast concrete kerb stone of

gray cement based concrete block 30cm length,30cm

height and 15cm thick of M200 grade concret as per

approved design and including excavation for fixing

in proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

86 Providing and fixing pre-cast Rubber Dye / steel Dye

inter locking concrete block 60mm thick with grade

of concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming

to IS 15658 : 2006 including 35 mm Sand layer for

levelling and filling the joint with sand in proper line

and level as per guidlines of IRC : SP 63-2018 etc.

87 Constructing sandwitch platform ofn18mm thick

polished black granite at top and 25mm thick kota

stone slab using cement mortar 1:3 for sandwich and

fitting at bottom & edges with water proof rigid

adhesives including macking necessary grooves in

walls with vertical kotastone 30mm X 2no sandwitch 9.00 SMT 3192.000

thick every 60cm center to center including alll

labour material of approved quality incl. full

moulded round front edge fixed in wall for partition

and jointed with grey cement slurry including

rubbing and polishing etc. complete

88 Providing and fixing Gun metal check or non-return

fullway wheel valve.(E) 40mm dia.

89 Providing and fixing Gun metal check or non-return

fullway wheel valve.(C) 25mm dia.

90 Providing and fixing PVC SWR Nahni Trap IS

for drain - 100 mm diameter with jali of the

following nominal diameter of self cleansing design

with C.I. screwed down or hinged grating including 16.00 NOS 726.000

the cost of cutting and making good the walls.e As

per Architect instructions and drawing or as directed

by engineer in charge.

91 Providing and fixing S.W. gully trap with C.I. grating

brick masonry chamber and water tight C.I. cover

with frame of 300mm x 300mm size (inside) with 10.00 NOS 1279.400

standard weight.(i) Square mouth traps (A) 100mm

x 100mm size P type. (up to. 10 ton)

92 Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends with

bricks having crushing strength not less than 35Kg.

Cm2 in C.M. 1:5 C.I. cover with frame (Light duty)

455mm x 610mm internal dimensions total weight

of cover with frame to be not less than 38Kg. (Wt. of 6.00 NOS 7109.350

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top

slab with 1:2:4 mix (1-cement :2- coarse sand :4-

graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x 850 mm

and 450mm deep for pipe lines with three or more

inlets. (up to 10 ton)

93 Providing and fixing ball cock of approved. quality as

directed.(A) Copper Metal 50mm dia

94 Providing & constructing BB masonry in C.M. 1:6 (1

cement : 6 coarse sand) and cement concrete 1:2:4(1

cement : 2 sand : 4 graded stone age. of 0mm size BT

kapchi) septic tank of 3m x 0.9 m x 1.5 m internal

dimension with necessary compartment of grit

chambers and septic tank with necessary inlet and

outlet connections with cement plaster (15 mm

thick) in C.M. 1:4 (1 cement : 4 sand) with water

proofing material 1:5:10 (1 cement : 4 sand) brick 1.00 NOS 28834.000

bat concrete bedding RCC 1:2:4 top cover slab 12 cm

thick with C.I. cover of 60 cm x 45 cm size (light

duty) 75mm dia. C.I. ventilating pipe 2 mt. long with

cowl vent 40mm thick IPS flooring 10 cm. thick

cement vata mild steel for steel and finishing to

exposed faces in C.M. 1:3 (1 cement : 3 sand) curing

etc. complete As per Architect instructions and

drawing or as directed by engineer in charge.

95 Providing and constructing sock pit of 3.00 mt. dia

inside and 5.00 mt. depth with honey combed

masonry upto 4.00 mt. from bottom and 1.00 mt.

brick masonry in C.M. 1:5 top with RCC slab cover of

M200 vent pipe 1.80 mt. long 75 mm dia & C.I. cover

and cowl vent etc. complete

96 Providing and fixing in position cowel went to

pipes.(B) 75 mm dia.

97 Providing and fixing in position cowel went to

pipes.(B) 100 mm dia.

98 Providing and fixing single layer waterproof gypsum

board 12.5 mm thick of the make Newgood Group

Co. Ltd. Or equivalent & Newgood Group Co. Ltd.

company sections using waterproof board of size

1220 mm x 1830 mm x 8.0 mm suspended by G.I

suspender of size 25 mm x 3 mm with intermediate

channel of size 18 mm x 40 mm x 0.80 mm at

mm center to center ceiling section of size 40 mm x 190.00 SMT 600.940

35 mm x 0.55 mm at 457 mm center to center and

perimeter channel A of size 20 mm x 27 mm x 30 mm

x 0.50 mm at edges & drops including paper tap sand

soffit cleat, anchor fastener, scotch bolt connecting

cleat joining compound top coat on ceiling including

making necessary opening for light fitting, diffuser

etc. complete as per detail drawing as directed.

99 Providing and Filling screned of burnt coal cinder

including and consolidation etc complete.

100 Providing and fixing screw down bib taps of

following size.(B) Brass chromium plated screws 3.00 NOS 184.980

down Bib Tap. (i) 15mm dia.

101 Providing and fixing pillar tap, capstan head, screw

down high pressure with screws, shanks and back 2.00 NOS 305.670

nuts. (i) 15mm dia.

102 Providing and fixing brass screw down stop tap.(C) 6.00 NOS 218.630

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

103 Providing and fixing SS Sink Glosy ASIS 304 Grade x

1mm thick with over all size 610x460 mm & bowl

size 560x410x200 with single hole for pillar tap

fixing in sandwitch platform including cutting holes 1.00 NOS 3012.000

and making gods the same, necessary fixtures,

connections and waste pipes with c.p. pillar cock

15mm heavy duty swan neck etc complete

104 Providing throating or plaster drip and moulding to

R.C.C. Chhajja.or grove plaster

105 Providing and fixing C.P. brass shower rose with

15mm or 20mm inlet.(A) 100mm dia. Each

106 Providing and fixing Terracotta Jali Block of

approved design, size, and thickness. The block shall

be factory-made, machine-pressed, and of uniform

shape with decorative. Blocks should be free from

cracks, warping, and efflorescence, with compressive

strength as per IS specifications. perforations for

ventilation and aesthetic appeal.

Material: Natural terracotta clay, kiln-fired for

strength and durability.

Finish: Smooth surface, reddish-brown natural

terracotta shade.

Design: Ornamental floral cutwork pattern with

central circular opening and curved petal-like

cutouts (as per sample approved).

Size: Approx. (200mm x 200mm x 63mm) or as

Installation: Blocks shall be fixed in position with

cement mortar (1:4) or as directed, joints neatly

finished, and alignment maintained to achieve the

desired pattern.

107 Providing and fixing Large Plain Dado & Picture Rail

of approved profile and design, suitable for exterior

application. The rail shall be manufactured from

high-quality weather-proof polymer / fibre-

reinforced material (FRP/PU/UPVC) or equivalent

durable material, resistant to moisture, UV rays,

thermal expansion, and weathering.

Size/Dimensions: Large section profile – approx. 90–

120 mm projection, 25–35 mm thickness (or as 32.00 RMT 2760.000

Installation: Rails to be fixed with weather-proof

adhesive and/or stainless steel screws with proper

joint treatment. All gaps to be sealed with exterior-

grade sealant to ensure water tightness.

Performance Requirements: Must withstand outdoor

exposure, resistant to rain, heat, humidity, and not

prone to cracking, warping, or discolouration.

108 Providing and fixing Decorative Exterior Corbels of

approved design, size (Approx.18" height), and

profile, suitable for outdoor architectural

applications. The corbels shall be manufactured from

high-quality weather-proof materials such as FRP

(Fibre Reinforced Polymer), GRC (Glass Reinforced

Concrete), or PU (Polyurethane) with UV stabilizers,

ensuring long-term durability against rain, heat, and

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

humidity. To be securely installed with stainless

steel fasteners, mechanical anchors, or adhesive as

per manufacturer’s specifications. Joints and gaps to

be sealed with exterior-grade sealant to prevent

109 Providing corrugated G.I. sheet of class-3 roofing

fixed with glavanished iron J or L Hooks, Bolts and

nuts 8mm diameter with bitumen and G.I. limpet

washer or G.I. limpet washer. filled with white lead

complete excluding the cost of purlins, Rafters and

Trusses.(1) 0.80 mm thick sheet.

110 Structural steel work ( Confirming to IS 4923 1997)

riveted, bolted or welded in builtup for all type

sections, in framed work, including cutting, hoisting,

fixing in position and applying a priming coat of 1032.00 KG 130.520

approved steel primer all complete as per the

structural designs and directions of Engineer in

Modern queen-size bed measuring 2000 × 1600 ×

300 mm, crafted with high-quality specified wood

and playwood for durability and long-lasting

strength. The bed features a premium laminate finish

that is scratch-resistant, moisture-resistant, and easy

to clean. Designed for convenience, it includes two

side drawers on both sides—each measuring 500 ×

450 × 450 mm—providing ample storage space for

essentials such as bedding, pillows, and personal

items as provided detail drawing and directed by

engineer in-charge.

112 Mattresses of sleep well , product name inspire type -

1950 x 1550x 150 Providing Bonnel type mattresses

of 1950 x 1550x 150 with high quality sleepwell

form as mentioned in specification with tempering

and edge support having 4 overlays for camfer

system of polypzopylene mesh insulator, 10 to

mm thick high density natural fabric pads in both 3.00 Nos. 8970.000

sides, 6 to 8 mm cotton fele on both sides and exotic

chain stitch deep qualiting with 5 to 20 mm high

density polyare thane foam on both sides . The

inspire tapestry of approved design and color by

architect in charge . above work with include

trasportation and all taxes include complete.

113 Providing, fabricating and placing TV Unit, floor-

mounted type, overall size 1800 mm (L) × 400 mm

(D) × 1600 mm (H). Unit made with 18 mm thick

premium-grade plywood with laminated / veneer

finish. Includes two side cabinets, open shelves, and

soft-close drawers. Back panel in 18 mm plywood

with laminate. All exposed edges finished with 2 mm

PVC edge banding; hardware: soft-close hinges,

telescopic channels, and concealed wall-mount

114 Dressing Unit ( 800x1600 ) :

Providing and fixing Dressing unit as shown in detail

drawing with 5mm mirror( modi gard glass fixed

with silicon solvant on ply wood) as approved by

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

engineer in charge of 1400 x 500 having wooden

(teak wood) frame 100mm x 25mm three sided

hanged on the wall with necessary fixture. The

Dressing Unit will have a drawer unit made up of

19mm plywood with necessary wooden beading in

Ghana teak as shown in drawing with 1.00 mm

laminate outside and 0.8mm laminate inside of

approved shade of century or greenlam with

telescopic channel of hetich or kaff . The unit is also

contain dressing stool made up of Ghana teak

wooden legs and frame with 3” U-foam of 40 density

with approved tapestry by engineer in charge. The

unit should be complete with providing dressing

light fixture (led fixture L- 300MM handles,

telescopic channels , hardware, 5MM mirror etc with

necessary melamine polish or as directed by

architect, incharge etc.

115 Dining Table

Providing and Fixing of dining table, The table size

available in 1500mm x 900mm x 750mm. Table leg 1.00 Nos. 13500.000

material use in solid wood and size of the solid wood

is 67mm x 67mm. as shown in image.

116 VIP Dining Table Chair :

Providing and fixing of godrej make dining chair, The

chair size available 980mm x 440mm x 540mm. Back

side leg material use laminate solid wood-22mm. 6.00 Nos. 4890.000

Lamination use -38mm x 28mm. Front leg material

solid wood use 1.5 x 1.538 x 38 mm solid wood. As

shown in image.

117 3 SEATER SOFA :- Manufacturing and Supply of

Three Seater Sofa

two seater sofa Size 2131(L) x 851(D) x

1. 50mm thick 40 Density + 50 mm Thik Super Soft

Sleep well Feather foam for Seat & back

2. 25mm thick 32 Density sleep well (Feather foam)

Super Soft black(Velvet) Foam and 300 GSM Fiber

for seat and back to be pasted over the 100mm thick 2.00 Nos. 53000.000

foam with good quality of Adhesive (Fevicol)

3. 12mm plywood and 19mm plywood (MR-303)

semi waterproof

4. Teak Wood Use In Sofa Framing

5. Zic Zac Spring + Belt Use in Seat.

6.upholstered in selected color at the time of

execution by Engineer (Max 700/- Per Mtr.)

118 Woven Rope Accent Lounge Chair :- Modern lounge

chair with a powder-coated metal frame, hand-

woven rope armrests, and cushioned seat and

backrest. Features a lightweight design, comfortable

foam cushions with removable fabric covers, and a

stylish natural-beige woven finish as directed by EIC.

119 CENTER TABLE

Providing and Fixing of Center Table, The table size

is 900 mm x 600 mm x 510 mm. 10 mm tampered

glass top and 8 mm tempered bottom glass for 1.00 Nos. 7250.000

storage option and frame should be make from

gread stainless steel pipe of size 25mm x25mm .

glass should be fixed with clear solution of

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

pedilite.legs bottom with 25mm pvc buffer. The Load

bearing Capacity -20 kg.

120 Sleep well Pillow’s – 17” x 27”

Springwel Fibre Pillows (750gm)

are filled with highly flexible hollow fibre..A very fine

channel of air running through the length of the

hollow fibre gives approximately 15% more volume

than solid fibre. As air is the added insulation,

pillows are giving airy feel in summer and maximum

warmth in winter.

121 Providing and placing Round Centre Table (36" dia.

and 18" height.) of approved make and design,

consisting of a rigid powder-coated steel/metal

frame and a circular top made of pre-laminated

board/toughened glass/marble (as approved). Table

shall be stable, durable, and suitable for office 3.00 No 7525.000

waiting areas, lounges, and meeting spaces. All

materials shall conform to standard specifications,

with smooth finish, properly levelled top, and anti-

rust coated frame. Complete in all respects as

directed by the Engineer-in-Charge.

122 Roll-up-Blind Blinds

Providing and fixing roller-up- blinds cutting as per

necessary size, cutting and fitting with aluminum

powder coated slim line channel with imported

mechanism, pattern trade including runners, spacer

hangers and fabrics per size of window, bottom

weight should be zinc coated (16 gauge to be used).

Including fitting to old window and labour etc.

complete as per detail instruction of engineer-in

charge and consultant.

123 Providing Double bed white –stripped cotton bed

sheet of Bombay dying with all four sides stitched 6.00 no 2050.000

and finished as approved by architect in charge.

124 Pillow cover

Providing Pillow cover ( 17” x 27” )– white stripped

design with fine stitching and finish of Bombay dying

make as approved by architect in charge.

125 Providing double bed Jaipuri Rajai of 3'6"x 6’6” with

cotton infill & even stitching having four sides 6.00 No 2300.000

borders and as approved by architect in charge.

126 Providing and placing wardrobe unit of overall size

fabricated from factory-made pre-laminated particle

board/plywood of approved shade and grade, with

all edges sealed using PVC edge banding. Wardrobe

to include hinged doors, internal shelving, hanging 3.00 No 28700.000

provision, and necessary hardware such as hinges,

handles, and magnetic catchers of approved make.

All materials shall conform to departmental

specifications and the item shall be completed in all

respects as directed by the Engineer-in-Charge.

127 Providing and fixing Stainless Steel (SS) Kitchen

Basket of approved size and type, manufactured

from 100% SS 304 grade wire with polished finish, 1.00 Set 21700.000

minimum wire thickness as per manufacturer

standards. Basket shall be factory-made, rust-

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

resistant, smoothly welded, and suitable for modular

kitchen storage. Complete with required fittings and

placed inside kitchen carcass as directed by the

Engineer-in-Charge.

128 Providing and fixing kitchen drawers and shutters

fabricated from boiling-water resistant (BWR)

18mm plywood of approved thickness, finished with

1.0 mm/1.25 mm thick laminate on exposed surfaces

and balancing laminate on inner faces. All edges to

be sealed with PVC edge banding. Drawers to include

necessary channels/slides and shutters to include

hinges and handles of approved make. Complete as

per design and as directed by the Engineer-in-

129 Providing and fixing sliding toughened glass

partition made from 18 mm thick toughened safety

glass, edges polished, fixed with approved powder-

coated aluminium/SS top track, bottom guide,

rollers, and sliding fittings. Partition shall be smooth 11.00 sqmt 4850.000

in operation, rigid, and securely fitted with necessary

accessories, including floor guide, stoppers, and

handles. Work to be completed in all respects as

directed by the Engineer-in-Charge.

130 Point wiring for Light / Bell with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated

multistrand copper wires, in following type of pipe

to be erected concealed in/ on surface on

wall/ceiling complete with 6A Modular type switch /

bell push & accessories and earth continuity of

following type, erected on PVC / Metallic box, single

mounting base frame covered with

textured/metallic front plate modules erected on /

in wall / ceiling as per pipe erected, with necessary

Lamp holder/ceiling rose / H.D.Connector as

directed. (e) in existing pipe erected flushed on

wall/ceiling complete CAT III

131 Point wiring for FAN with 2-1.5 sq.mm & earthwire

of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multistrand copper wires,

in following type of pipe to be erected concealed in /

flushed on wall/ceiling complete with 6A Modular

type switch and hum free EME four or more step

type electronic fan regulator with separately

mounted and accessories with earth continuity of

following type erected on PVC / Metallic box, single

mounting base frame covered with textured/metallic

front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (e) in existing pipe

erected flushed on wall/ceiling completeCAT III

132 Point wiring for Looped Plug with 6A Modular type

switch & 5 pin socket erected on PVC / Metallic box,

single mounting base frame covered with textured / 20.00 PT 255.000

metallic front plate modules erected on / in wall /

ceiling with following type accessories. CAT III

133A Providing following type of Modular Type

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

Accessories mounted with pvc / metallic box, single

mounting base frame covered with textured /

metallic front plate , modules erected with

necessary connection. As desired by Engineer In

133A (7)Blank Plate Single Cat III 10.00 NO 25.000

133B (11) 6 Amp. Bell push cat III 1.00 NO 150.000

133C (19) Modular Indicating Call Bell 1.00 NO 326.000

133D (21) Foot Light as per colour requirement with

concealed box, modular accessories, acrylic glass

cover with suitable LED watt with all accessories as

per following module(a) Two modules Cat-III

133E (24) Angle holder cat III 10.00 NO 64.000

134 Providing & erecting following type of Modular Type

Accessories with necessary connection. As desired

by Engineer In charge

134A (1) 6 Amp. SP one way switch 6.00 NO 27.000

135 Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall 4.00 NO 505.000

/ ceiling as per pipe erected with following type of

accessories.[I] For 6A Plug and 6 a switch with 2-1.5

sq.mm Cu. Wire from nearby switchboard/mcb db

board(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

completeCat. III

136 Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall

/ ceiling as per pipe erected with following type of

accessories.( III) for 16 amp plug and 16 amp switch

with 2-4 sq mm cu. wire with 2.5 sq mm earthing

wire from mcb db board.(e) in existing pipe erected

flushed on wall/ceiling complete cat III.

137 Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution

& Clamps with following dia of pipes, in approved

manner as directed (b) 20 mm

138 Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in

following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper 250.00 MTR 62.000

conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (E)

in existing pipe (b) 2 wire 2.5 sq. mm

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

139 Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC 155.00 MTR 86.000

insulated stranded wire of green colour for earth

continuity of following size (E) in existing pipe (a)

140 Providing & erecting Approved make Power Saving

50 Watt Ceiling Fan with double ball bearing ISI

mark with Condenser 230 volt A.C. 50 Hz 1200 mm

sweep complete having 3blades with aluminium

blades with , canopy & 30 cms. down rod erected

with 24/ 0.2, 3 core flexible wire with

earthing.(Make shall be approved by Engineer in

141 Supplying and erecting 19 / 20 mm. nominal bore

Medium Class M.S. Pipe down rod erected duly

painted for fan complete with proper insulation

without leakage and earthing.

142 Supplying & erecting Fan Hook of 10 mm M.S. Round

bar grouted in RCC slab with Making the site as 9.00 NO 43.000

143 Supplying & erecting approved make low noise

decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame. 200 mm

with 1350 rpm cat II

144 Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.9, THD <

%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

shown.)(A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete.IP20 (ii)

11-15 watts, Surge-2 KV Cat-lll

145 Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and

high U.V. & corrosion resistance with diffuser with 12.00 NO 293.000

company mark/name 160V to 270V, Power Factor

more than 0.95, THD < 15%,CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED LED driver

efficiency > 85 %( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Tube Light with

integral driver (lll) 18-20 Watts, Surge - 2KV,IP-20,

146 Supplying and erecting led lamps with following

wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable 6.00 NO 111.000

for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED

Lamps integral type, with PC diffuser suitable LAMP

holder( ll ) 5 to 8 watts Cat-lll

147 providing and erecting 10 watt to 15 watt outdoor

doom light complete as per directed by engineer 5.00 NO 1500.000

148 Providing & Erecting 3mm thick acrylic Sheet with

420.00 sq.inch 3.000

grooving as directed.

149 Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/

lenses, with toughened glass with company

mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency >

85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.)(A) Street Light (IP-65),

Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (i)

above 36 to 48 watts Cat-lll

150 Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The 2.00 NO 1478.000

DBs should be used of same company of MCB to be

used) suitable for(A) single phase incoming and

horizontal single phase outgoing(b) sheet steel

double door (IP-43) (iv)12 way

151 Providing & erecting 240 V MCB double pole switch

for lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box

having following capacity (B) 40 amp Cat. III

152 providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on single phase 240 2.00 NO 2213.000

V,50Hz. having characteristic of quick action &

tripping with all advance feature & do not

incorporate any electronic component. for following

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

Max. rating erected as directed (iii) 40 Amps. DP DP

153 providing and erecting Miniature circuit breaker

single pole 6A to 25A suitable to operate on 240 V

A.C. system and having breaking capacity 10 KA to 20.00 NO 111.000

be erected in existing box. confirming to IS

8828/1996 with ISI Mark (B) Cat.III

154 Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I. Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia

of 12 mm with constant ohmic value surrounded by

highly conductive compound with high charge

dissipation suitable for following type of applications

with chamber and heavy duty cover. (approved

make OEM has to submit test certificate) & having

back filling compound of (B) Inner chemical (CCM

Compound) - Resistivity :- 0.2/ meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2% (C) Back fill

Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test

report must be submitted. (a ) For Electrical

installation up to 440V in normal soil. Length of Pipe

: 1.00 mtrs. Back filling Compound :1 no. Bag of

155 Providing and Erecting Annealed bare Copper wire

156 Providing & erecting open well type horizontal mono

block pump set with stainless steel body having

following specification (C) 1 H.P. single phase open

well motor pump set suitable for 185 LPM discharge

@ 25 mtr. head, suitable for 32 mm dia. Delivery pipe

with control panel. Cat. II

157 Supplying & erecting XLPE(IS:7098)(I)-88 ISI

unarmoured copper cable 1.1 KV grade to be erected 32.00 MTR 136.000

as directed of following size. (E) 3 core 2.5 Sq. mm

158 Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor

for 1.1 KV. to be laid on wall with necessary clamps 55.00 MTR 142.000

or in existing trench / pipe of following size of

cables. (E) 3 core 16 Sq. mm

159 Making trench in soft soil of suitable width of 90 cm

deep for laying cable or locating the fault all over the

run and back filling the same and making the surface

as normal ground.

160 Providing and erecting Inverter based approved

make split air-conditioning unit consisting of

condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary compressor

with accessories etc. duly connected separately

erected evaporating unit and blower motor with its

accessories by means of extra supplied proper

insulated copper tubing,drain PVC pipes suitable for

Item Description of Item (with brief specification Quantity Unit Rate In Amount

No and reference to book of specifications) figures

( cost includes Eco Friendly green gas charging and

15A plug top & Remote Control & MS Stand) with

necessary core cutting.(1)For 3 Star Rating of

current year (B) for 1.5 ton capacity Premium cat.

Rupees Seventy Six Lakh Fifty Seven Thousand Four Hundred Five Paise Thirty Five Only

I/We am/are willing to carry out the work at… ...................... % above/below percent(Should

be written in figures and words) of the estimated rate mentioned above. Amount of my /our

tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

(B) For Item Rate Tender (For above INR 50 Cr.):

Item Description of Item Quantity Unit Rate Amount

No (with brief specification

and reference to book of In In

specifications) figures Words

(A) Total Tendered Amount

(B) Rebate on above tendered amount (if any) % (in figure) ………………………………

(C)Net Tendered Amount (A-B) (in figure) ………………………………

1. The Contractor shall exhibit a board with brief details of work as directed by the Engineer-In-Charge

for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R. NO.:

MIS102010/17/K1 Dated:30/07/2018 as stated in S.O.R. therefore in R.C.C. items where there is a change

as per actual mix design the cost of difference of cement consumption have been deducted from the rate of

original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Sr. Divisional Accounts Officer Executive Engineer

Mkt. H.W. Sub Dn. No-1 Sipu Project Division Sipu Project Division

Mukteshwar Palanpur Palanpur