CA NO GE(N)AMB-24/2022-23 REPAIR TO JOINERY, PLUMBING, SANITARY, PLASTERING AND OTHER CONNECTED BUILDING REPAIR WORK IN OTM ACCN-III AREA OF AGE B/R-II (NORTH) UNDER GE (N) AMBALA CANTT

Amount

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts, wells, manholes etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including spreading, levlling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated soil to a distance exceeding 250 metre and not exceeding 500 metre and deposited where directed at a level not exceeding 1.50m above the starting point, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

Demolition of stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons, etc. removing the rubbish outside the defence land ,complete all as specified

Material and labour PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for providing 75 mm thick cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour brick work with sub class 'B' old size bricks straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290 (Gde E-165) complete all as specified and as directed by the Engineer-in-Charge.

S&F fixed side hung type without sash bar window, ventilator shutter made from powder coated aluminium section (minimum thickness of powder coating 50 micron) comprising of the following sections, including the cost of EPDM rubber/ neoprene gasket required (fittings shall be paid for seperatly) with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge:- (a) Window frame 101.6mm x 44.45mm x 2.10mm thick (b) Window shutter top bottom and sides 47.62mm x 44.45mm x 1.95mm thick (c) Mullion bottom 53mm x 52mm x 2.00mm thick (d) Glazing clip weighing not less than 0.097Kg/matre Note : (a). Glazing/wire mesh shall be measured and paid separately; (b). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required. (c). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fixing powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows, ventilators, etc. including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

S & F anodised aluminium grill (anodized transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the window frame with C.P brass/ stainless steel screws @ 200 mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for repairing of all type aluminium window/door shutter with frame and refixing it after resecuring its frame work by means of tightening with new screw or by new frame ,cleats, rubber gasket and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge. Note:- New frame shall be measured and paid for separately.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) Frame/ chowkats shall be of ERW hollow P section of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill , other accessoriries and connected items as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staple as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelam sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing stainless steel butt hinges 100mm long medium weight complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing aluminium (Diecast) body hydraulically door closer regulated,designation No.3, universal type,suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg as in repair complete all as specified and as directed by the Engr-in-charge.

Supply and fixing mild steel helical door spring, 200 mm long, fixed to wooden chowkats or welded to angle iron/ steel door frames complete all as specified and as directed by the Engr-in-charge.

Supply and fixing in repair mild steel powder coated wooden finish curtain rod 25mm dia having wall thickness 1.60 mm fixed with and including decorative brackets ,stop roller and glass at the end etc complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets and false ceiling frame work complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing false ceiling with semi perforated 12 mm thick micro tegular edged at all hights with GRG(glass fiber reinforced gypsum ) false ceiling tiles of size 595mmx595mm of approved texture ,design and pattern having moisture content less than 2% ,humidity resistance of 99% ,NRC 0.5 to 0.75 as per IS 8225-1987 ,non- combustile as per BS475 (part-4) -1970 and light code description unit rate No.429 SUB HEAD :26.0 new technologies and material reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 gms per sqm including both sides ) comprising of main -T runners of size 15x32mm of length 3000mm ,cross T of size 15x32mm of length 1200mm and secondry intermediate cross-T of size 15x32mm of length 600 mm to form grid module of size 600x600mm ,suspended from ceiling using galvanised mild steel items (galvanising @80 gms per sqm ) i.e, 50mm long ,8 mm outer diameter M-6 dash fastners ,6mm dia fully threaded hanger rod upto 1000mm length and L- Shape level adjuster of size 85x25x2mm . Galvanised iron perimeter wall angle of size 24x24x0.4mm of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 8mm thick hollow profile designer PVC paneling with panel of width 250mm to 300mm fixed to wall/ceiling with screws and rawal plug including PVC beading (U, L) section, complete all as specified and as directed by the Engr-in-charge.

Supply and fix 12 mm thick prelaminated particale board,interior grade, prelaminated both side with decorative choice lamination and fixed to aluminium door with glazing clips, rubber gasket etc complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 5 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement but using water proofing compound @ 2% by weight of cement or as per manufacturer's instructions complete all as specified and as directed by the Engineer-in-Charge. (water proofing compound shall be measured and paid for separatally)

Supply only water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of new plastered/ unplastered surfaces of brick/concrete ceiling and applying three coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of newly plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed by the Engineer-in-Charge.

M &L preparation of old decoraded plastered/unplastered surfaces of walls and applying one coat of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparing new plastered surfaces and applying two coats of oil bound distemper with painting roller over a coat of alkali resistant primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour applying 1 to 2 mm thick wall care putty white cement based in two or more coats to achive smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash over prepared surfaces of ceiling, pillar, cornices complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of the ceiling complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls/ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of the walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper with painting roller over prepared surfaces of the walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for complete removal of existing treatment on surfaces of walls by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface including filling up all cracks with Shalimar tar plastic (STP) crack filler and also, make good to plastered surface complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old wooden surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls, pillars, cornices etc. and applying two coats of plastic emulsion paint with painting roller complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls and applying two coats of exterior acrylic emulsion paint with painting roller over prepared surfaces complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge

Material and labour Non-skid ceramic coloured tiles joint free 1st quality (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

Material and labour Non Skid coloured ceramic tiles joint free premium/1st quality of same description as of floor tiles in serial item No 62 above but 150mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour Double charged, vitrified ceramic light shade tiles, premium/1st quality 10mm thick (square/rectangular) area of each tile exceeding 0.42 sqm and not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour Double charged, vitrified ceramic light shade tiles premium/1st quality 10mm thick of same description as of floor tiles as in serial item No 64 above but 150mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour 25mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base, finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour glazed ceramic coloured tiles joint free 1st quality in vertical surfaces/ skirtings/dados of size 450x350x7mm thick or nearest size as required , set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 16-18 mm thick Baroda green stone slab as in skirting, dado, window cills, jambs, cooking platform ,etc.machine cut and machine polished, and moulded over and including 10mm thick in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and jointed with grey cement slurry complete, all as specified.

Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour machine cut kota stone slab flooring 16 to 18 mm thick of size not less than 550mm x 550mm in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for machine cut kota stone slab 16-18 mm thick laid on verticle surface (cut from size of kota stone not less than 550 x 550 mm) and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar 1:4 on brick work or concrete surfaces,complete all as specified and as directed by the Engr-in-charge.

M &L 10mm thick coloured paver tiles (Endura Tiles) of size 300 x 300mm in floors etc set and jointed in neat cment slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in C.M 1 :4 ,complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Material and labour galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body and crutch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing fancy type 15mm bore cast copper alloy chromium plated angular stop valves, screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 15mm bore Gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash hand basin, white, flat back of size 550mmx400mm with pedestal, ISI marked. fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connection, flush pipes, etc. for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe and complete accessories as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing plastic water closet seat cover, white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 600 mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 32/40mm dia PVC waste pipe of standard length for wash hand basin / Kitchen sink etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) tripple layer body, 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight-210 grm) complete all as specified and as directed by the Engineer-in-Charge. Note : Water storage tank shall be White in colour.

Supply and fixing as in repair 500 litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minium weight-210 grm) complete all as specified and as directed by the Engineer-in-Charge Note:- Tank shall be in white colour.

Dismantling of 100/75 mm cast iron, PVC pipe or reinforced concrete drain pipes any dia, set in cement mortar including taking out from trenches, if required complete all as specified and as directed by the Engineer-in-Charge.

Material and labour 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and directed. (Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing as in repair stainless steel grating cover 100 mm dia fixed complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing as in repair waste fittings, 32 mm dia brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair waste fittings, 38 mm dia brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing & adjusting shutters of any description not exc 1.00 Sqm each, without taking down shutters from frame complete all as specified and as directed by the Engineer-in-Charge

Resecuring or easing & adjusting shutters of any description exc 1 sqm and not exc 2 Sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge

Taking down carefully steel door shutter exceeding area 1.00 sqm but not exceeding 2.00 Sqm including cutting, welding and adjusting as per opening and refiixng the same at same location complete all as specified and as directed by the Engineer-in-Charge (new angle iron etc shall be measuared and paid for separately)

Material and labour for running welding in repairs thickness of metal to be welded not exc 6mm complete all as specified and directed by Engr-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

Material and labour sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

Material and labour figured glass 4mm thick pin head type and fixed to aluminium door with glazing clips, rubber gasket etc in square n exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

Material and labour concrete bed to drain pipes of 110mm bore, including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate complete all as specified and as directed by the Engineer-in-Charge

M&L cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity 250 litre and upto and including 1000 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc .

Material and labour for cutting and uprooting of tree roots and unwanted vegetations on roof and wall surfaces by digging safely in concrete roof or brick wall and pouring acid or approved chemical to avoid further growth of roots land making good the surfaces by filling cracks and disturbed portion in cement mortar (1:3) or PCC 12:4 type B-0 (using 12.5mm size crushed stone aggregates) without using extra cement, of each area exceeding 0.5 sqm but not exc 1.00 sqm complete all as specified and as directed by the Engineer-in-Charge. Note:- The approvale of pouring acid shall be got approved by GE before incorporating in above item.

S & F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm aluminium mortice lock, vertical type, two lever with dublicate key complete all as specified and as directed by the Engineer-in-Charge.

S&F 200 mm long disk type aluminium handle complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long peg stay of aluminium and fixed to aluminium window complete all as specified and as directed by the Engineer-in-Charge.

Sawhney Constructions

M/s Mangal Construction Co.

Durga Enterprises

m/s parmod kamar

dhingra builders

Jai Bala Ji

M/S Mahal Enterprises