Construction of Govt Sen Sec School Ghaniyar in Tehsil Balichowki Distt Mandi SH C/o laboratory and class room Library computer room and craft room including staircase under RMSA

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Cutting in earth work in all heights and deptth in all kinds of classification of soil including stuarted soil comparising of pick work, jumper work, jumper, blasting work both in spot and hard rock with chieseling/weding out of rock ( where blasting is probhiited) and their intermediate classification of soil setting out time required line, side slope, trimming ottoms and levels as shown in drawing and as per direction Engineer in charge at site stacking the useful/unuseful matrial at required wdth or an approved dumping site through all modes of transportation i/c head load or animal load and carriage of all laour, machenary, material, tools and equipment and safety measures and incidentals necessary to complete the work. If useful matrial such as slate singhal sand and aggregate shall be soerted out and stacked along side of work. Any loss to the publicor private property during execution of work shall e absolute responcibility of the contractor which shall be duly compensated y him in all cases as per direction Engineer - in - charge. The recovery of usefull stones of 36.54 cubic meter( thirty six point fifty four cubic meter) @ 300/ per cubic meter anounting to 10962.00 only shall be done on prorata basis for quantity of cutting in earth work effected.

Earth work in excavation for structure as per drawing and technical specification clause 305.1including setting out construction of shoring and bracing removal of stumps and other deletarious material and disposal up to any lead dressing of sides and bottom and back filling in trenches with excavated suitable material ordinary soil including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Back filling behind abutment wing wall and retainling wall complete as per drawing & technical specification clause 1204.3.8 and including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing weep hole in brick masonry/ stone masonry / plain reinforced concrete abutment, wing wall, return wall with 100mm dia.(one hundred millimetre diametre) PVC pipe extending through the full width of the structures with slope of 1V:20H (one vertical isto twenty horizontal) towards drawing face complete as per drawing and technical specifications clauses 614,709,1204.3.7 with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification Clause 802,803,1202 and 1203 in cement concrete 1:4:8 (one cement: four sand : eight graded stone aggregate 40mm nominal size) including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Demolition of stone masonry below G.L upto 15 mtr. (fifteen metre) depth stacking standing of servciable materials and disposal of un - serciable material with any lead including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, for all heights of propping and centring below supporting floor to cailing up to all heights and removal of same for insitu reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Beams, cantilever, girders and lintels Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintelsof any depthes up to one flors

flat surfaces such as soffits of suspended floors,roofs, landings and the like floors etc. upto any in thickness.

Stair cases with sloping or stepped soffits excluding landing.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in Foundation and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire in all tore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. (two point seven five kilogram of cement per sq.metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing throating or plaster drip and moulding to R.C.C. chajja including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Brick work using common burnt clay building bricks in super structure upto floor all level in cement mortar 1:6 (one cement : six sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

2nd class Brick work using common burnt clay building bricks of approved kilh in super structure upto floor all level in cement mortar 1:6 (one cement : six sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Half brick masonry in common burnt clay building bricks in Cement Mortar 1:4 (1 cement:4 sand) Second Class Bricks including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) and down gauge foundation and plinth upto floor all level in Cement Mortar 1:6 (one cement : six sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 40 mm (fourty millimetre) thick frame work 12 mm (twelve millimetre) thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (1 cement:2 sand :4 graded stone aggregate 40mm (fourty millimetre) nominal size) and curing complete excluding cost of form work in including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge. Foundation and plinth.

Providing and laying mechanically mixed and vibrated cement concrete work M-20 (twenty) nominal size and curing complete excluding cost of form work and reinforcement for reinforced, concrete work in including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge. Suspended Floor roofs, landing and shelves and their support balconies,beams, girders, bressumers and contilever upto floor any level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor any level.

Providing and laying upto floor all level reinforced cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm (twenty millimetre) nominal size to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing 300x16mm (three hundred sixteen millimetre) anodized aluminium sliding door bolts with nuts and screws etc. complete including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Providing and fixing aluminium tower bolts (berrel type) anodized trans-parent or dyed to required shade and colour with screws etc. complete including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge. 250x10mm (two hundred fifty into ten millimetre)

200x10 mm (two hundred into ten millimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge. 100 mm (one hundred millimetre)

125 mm (one hundred twenty five millimetre)

Providing and fixing 100mm (hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing partical board ceiling of approved quality with butt jointing and nail (frame work and cover fillets to be paid for separately) Cement bonded particle board 8 mm (eight millimetre) thick including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing 40 mm (fourty millimetre) wide and 4 mm (four millimetre) thick glass strips in joints of terrazzo floors including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and laying 40 mm (fourty millimetre) Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Extra for making chequers of approved pattern on cement concrete floors Steps Landings and pavements etc. including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

15 mm (fifteen millimetre) thick Cement plaster skirting upto 30cm (thirty centimetre) height with cement morter 1:3 (1 cement:3 sand) finished with a floating coat of neat cement including rounding of junction with floor including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing and fixing 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing and chajjas with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six millimetre) dia & prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing valley 60 cm (sixty centimetre) overall 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia with prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 40 mm (fourty millimetre) thick 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing 2nd class deodar wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position. including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing and fixing 40mm (fourty millimetre) thick 2nd class deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing and fixing M.S.fan clamp type -1 of 16 mm (sixteen millimetre) dia M.S. bar bent to shape with hooked ends in R.C.C slab during laying including painting the exposed portion of loop,all as per standard design complete including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing and fixing 85 cm (eighty five centimetre) high moulded hand railing of M.S rectangular hollow pipe 75x50mm (seventy five into fifty millimetre) of 14 (fourteen) gauge MS black sheet make hand rail and MS square bar 20 mm size bluster embaded in RCC steps or easte of slab priming coat including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters,purlins connected to common rafters and the like.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separtely) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen millimetre) Cement plaster in single coat on the rough side of brick/ concrete/ stone walls for interior plastering upto floor any level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth Cement Mortar 1:6 (1Cement:6 Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen millimetre) cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor any level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth Cement Mortar 1:6 (1Cement:6 Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting two costs (excluding priming cost on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel white paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting Readymixed paint brushing wood primer pink including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Painting two coats (excluding priming coat)on new wood and wood based surfaces,under coat with enamel and finishing coating with flat oil paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping With paint other then white including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

White washing with chalk wahiting on decorated cloth or Hassian ceiling(one coat) to give an even shade including thoroughly brooming the surface to remove all dirt,dust,mortar drops and losse scales of chalk wash and other foreign matter including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing plinth protection 50mm (Fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three sand : six Graded stone aggregated 20mm (Twenty millimetre) nominal size) mechanically mix finishing surface of concrete smooth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two centimetre) in cement mortor 1:6 (one cement: six sand) and in side blastering with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4 (one cement :two sand :four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 20mm (Twenty Millimetre) nominal bore

Providing and laying in trenches, galvanized mild steel tubes (heavy grade), tube fittings (earth work in trenches to be measured and paid separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 20mm (Twenty Millimetre) dia

Providing and fixing 500 ltr. (five hundred litre) Net capacity PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 110 mm (one hundred ten millimetre)dia PVC collers ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 110 mm (one hundred ten millimetre) PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia c.p brass pillar tap with capstan head including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) brass stop cock including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing brass full way valve with wheel including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 20mm (twenty millimetre) nominal bore

Khajan Singh